Search Documents

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By Milton E. Wadsworth

The reduction of a metal in an aqueous solution may be defined in terms of its source of electrons. In electrolytic reduction electrons flow as a result of applied voltages. In other systems electron sources are reducing gases or metals of lower electron affinity. In the latter two cases it is increasingly evident that reduction is electro-chemical in nature in that electrons flow through one or more conducting phases even though the discharge reactions may not be rate controlling. Electrode processes impmtant in reduction and metal deposition are reviewed and extended to contact reduction by precipitation (cementation) on mme electropositive metals. Contact reduc- tion Processes are ancient in origin and represent techniques which have had successful application for hundreds of years. In spite of this, little has been understood in terms of the dynamic properties of such systems or of important side reactions. In recent years an increasing amount of laboratory work has been carried out on contact reduction and an attempt is made here to summarize the important findings. Undoubtedly the interest aroused recently may be attributed to improved reactor design which has demonstrated on a commercial basis accelerated metal recovery by taking advantage of important kinetic and chemical parameters. of gold cyanide (Au(CN)-), respectively. The most common method for the reduction of ions in solution is by electrolysis. The impure metal is made the anode and the ions are reduced at the cathode. Leach liquors containing reducible ions may similarly be reduced electrolytically using an inert anode. The latter process is referred to as electrowinning. In recent years hydrogen has been used successfully as a gaseous re-Metallurgical Society of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). He was also a member of the Executive Board of the Metallurgical Society (AIME). In 1957 Dr. WADSWORTH was given the AlME Best Paper Award as coauthor of a paper on the roasting of sphalerite. On July 1, 1968 Dr. WADS-WORTH started an 24 month assignment in the Philippine Islands to assist in the development of graduate metallurgical engineering at the University of the Philippines. In addition to graduate teaching and curriculum development he will establish research programs to develop extraction processes for metals production in the islands. The project is supported by the Ford Foundation through Educational Projects, Incorporated.

Jan 1, 1970

By R. J. Charles

F. C. Bond: This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = —Cdx/x [1] either Corn must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant. According to the Third Theory, in the general case n is a constant equal to 3/2, and C is a variable related to the work index Wi. If x is placed equal to P (the size in microns which 80 pct of the product passes) and F is the size 80 pct of the feed passes, then C equals 5 W1, and dE = 5 -5 Widx/x = 10 Wi 10 Wi w = vP vF which is the basic equation of the Third Theory. It is apparent that this integration involves the error of treating the parameter Wi as a constant, just as the author's treatment involves the error of integrating his variable n as a constant. These errors are probably relatively unimportant, considering the small range of the variables. When more is known about the factors contained in the work index, Eq. 1 can be revised as a partial differential equation. The Third Theory exponent of 1/2, or n = 3/2 in the Charles' differential equation (Eq. l), was not chosen primarily because it is the average between the Kick and Rittinger exponents; this may be merely fortuitous, since it is illogical to define truth as the average between two errors. It was first discovered from the study of a large mass of crushing and grinding data and confirmed by laboratory testing. The general correspondence of the Third Theory equation to actual crushing and grinding results over the entire size reduction range argues strongly that a fundamental phenomenon is involved. The a posteriori theoretical explanation of the constant Third Theory exponent is that the work done in breaking rock is proportional to the length of the crack tips formed. Compressive force applied to the rock results in deformation and strain energy. When this locally exceeds the breaking strength a crack tip forms, the surrounding strain energy flows to the crack tip and extends it to split the rock, with release of the energy as heat. Under rapid impact the crack tip may form before the strain has reached equilibrium, resulting in less energy expenditure and probably a coarser product. In any case, the elastic limit of a brittle material is practically the same as its breaking strength, and the work necessary to form the crack tip is the work required to break. The crack length of a ton of broken rock cannot be measured directly. However, the particle shapes of feed and product are similar, and the crack length is considered equal to the square root of one half of the new surface area formed. It is, therefore, proportional to 1/vD, where D is the equivalent product particle diameter. This is the basis of the Third Theory equation. Many secondary factors can be imposed upon the crack length breakage. These may cause the Third Theory work index to increase or decrease somewhat as the product size becomes finer. The work index is properly a parameter rather than a constant, making it an increasingly valuable practical criterion of the work input required in crushing and grinding.

Jan 1, 1959

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By F. E. Wood

Since the earliest discoveries of oil in the Rocky Mountain area the spirit of cooperation in drilling and production programs has prevailed. There has scarcely been a field which has not been developed in an orderly manner through mutual agreement between competitive operators. An appreciable saving has resulted, as many unnecessary wells have been eliminated. We have unit operation plans and agreements which were developed at an early date. Rock River, found in 1918, has been a unit operation. One of the first prorate agreements ever attempted was made in Salt Creek in 1921. Teapot, first developed in 1922, has been a unit operation; the lessee, the Government, and the lessor, one operator. South Casper Creek, found in 1918, has been developed as a unit. Rex Lake, found in 1923, is a unit operation. The list might be extended materially but it serves to indicate that the Rocky Mountain region enjoyed the fruits of unit operation at an early date. It is concluded from this unitization study in the Rocky Mountain region that there is an appreciable saving in both development and production costs as well as the elimination of waste of a natural resource. Certainly, when unit operation conserves an irreplaceable natural resource as well as capital, any legal or political impediment to its successful development will be overcome. If one company supervises the operations in one field, it appears to be a unit operation. This may not be true if the lands involved have been leased from a great number of lessors. Royalty holders create a most intense competitive operation. The Rocky Mountain region has its full quota of such diversified interests. The original study calls for consideration of two types of fields, unit and near-unit operation. This Committee has felt that if an agreement of any character has brought about a saving it is an approach to unit operation. The fields have been classified into four types: 1. Unit Operation.—Any field whereby the competitive drilling-drainage feature is or will be absent in the development and operation of the pool.

Jan 1, 1930

By C. Altstetter, Y. Huang, E. de Lamotte

Nitrogen was introduced into pure niobium (colutn-bium) and dilute Nb- Zr alloy wires by equilibration with pure nitrogen gas at high temperatures. Room-temperature hardness was correlated with the alloy composition, heat treatment, and microstructure. Hardness was found to be most sensitive to the amount of nitrogen in solution; however, a significant hardening up to 500 Dph look place upon aging of quenched alloys. A coarse dispersion of nitride did not significantly increase the hardness of the material though the nitride was found to have a hardness of 1400 Khn. BY now the marked effect of nitrogen on the properties of bcc refractorv metals is we ll-documented. There are few studies, however, in which the state of the solute has been carefully controlled. Indeed, the composition-temperature-pressure relationships in nitrogen-refractory metal systems have been determined precisely for only niobium and tantalum.'-4 Most investigations on niobium have dealt with alloys High-nitrogen alloys cleaved on (100) planes and had negligible ductility. Precipitation was found to occur in either a discontinuous or a continuous fashion, depending on the composition and cooling rates. Upon cooling, the precipitation first proceeded discontinu-ously by the nucleation of nilride needles at subbound-aries and subsequent growth of a two-phase microcon-stituent. At lower temperatures continuous precipitation occurred in the subgrain interior ahead of the discontinuous precipitation interface. containing nitrogen, carbon, and oxygen in significant but uncontrolled and, in several instances, undetermined amounts. Thus, there has been some uncertainty regarding the presence and the distribution of precipitates. This paper presents results which relate the hardness and microstructure to the heat treatment and nitrogen content of niobium and Nb-Zr alloys. Niobium rod* produced by the Wah Chang Corp.

Jan 1, 1968

By John V. Beall

As recently as 1964, the situation in the Australian iron ore industry was chiefly one of potential. The only producer was the Broken Hill Pty. (BHP). That company mined about 5 million tpy from deposits in the Middleback Range in South Australia and at Yampi Sound in Western Australia. No ore was exported from Australia. Now, just five years later, and after expenditures amounting to approximately one half billion dollars, BHP and seven new companies exported about 15 million tons (long tons) of iron ore and pellets as well as meeting Australia's own annual requirements of approximately 8.5 million tons of ore. Early this year, the volume of iron ore on order stood at 328 mil- lion tons to be delivered over a period of 15 years, but Cliffs Western negotiations for sale of Robe River iron ore have boosted the volume to the new high of 466 million tons. All of this has meant a great deal to Australia in terms of new income. In fiscal year 1967 (ending June 30, 1967) exports of iron ore amounted to $52 million; in 1968, $128 million and by 1'972 the Bureau of Mineral Resources expects the value of exports from iron ore to reach $242 million. In achieving the position of major- supplier of iron ore to the Japanese steelmakers, it was necessary to build a great many new facilities, mostly in Western Australia. Three railroads, 70 miles long, 182 miles and 265 miles were constructed. A new port was created at Dampier; Port Hedland was deepened and otherwise improved; both of these ports are in Western Australia. In Tasmania, Savage River developers built an offshore shiploading station that has received the recognition of engineers internationally. At least a half dozen new communities have been founded. The narrow gage railroad from Kalgoorlie to Perth and Freemantle was replaced with a standard gage line.

Jan 6, 1969

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3', as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By C. E. Arnold

IN attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?", The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized; and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a, case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman's ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total. costs will be as shown in the following table:

Jan 9, 1916

By Lyon F. Terry

INCREASING domestic demand for products, a sharp reduction in exports to Europe, and a rise in imports from South America were the chief features of the economic side of the industry in 1940. As the war progressed it became evident that exports to former European customers were being cut off or drastically reduced, leaving heavy inventories of products in the hands of many American refiners who had anticipated larger demands from the belligerents. Stocks of motor fuel reached burden-some proportions early in the year for the added reason that refining operations were stimulated by heavy demand for heating oils. Excessive tanker rates for Gulf to Eastern Seaboard movements during the first part of 1940 contributed to the accumulation of products on the Gulf Coast, where refinery gasoline prices were forced to extremely low levels by midyear. Tanker rates receded to normal during the summer but have since risen again to the approximate equivalent of pipe-line tariffs from the Mid-Continent.

Jan 1, 1941

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By E. B. Burwell, R. H. Nesbitt

Designed by army engineers, the NX borehole camera provides the most economical method of subsurface exploration so far devised. Continuous cylindrical color photographs now reveal minor flaws in foundation bedrock not always disclosed by borehole samples. A unique projector transforms the photographs into true-to-scale images of three dimensions. ANEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery. The pilot model of the camera has more than paid for itself as a result of its success in bringing to the surface at two dams information previously obtainable only by costly drilling of mansized boreholes for subsurface on-the-spot examination. Such bores cost as much as $200 per lineal foot as against $10 per ft for the conventional 3-in. or NX exploratory core borings from which the present invention derives its name. The NX camera can now photograph completely the interior surface of these borings. Research and development for the first camera and projection equipment were conducted by Engineering Research Associates, Division of Remington Rand, Inc., under the technical supervision of the Geology and Geophysics Branch, Office of the Chief of Army Engineers in Washington, in accordance with plans and specifications furnished by this branch. Subsequent modifications of the camera-lowering device, transporting equipment, and special field tools were made in the Corps of Engineers' Ohio River Division Laboratories in Cincinnati. The background of this development is interesting. Among the more difficult foundation problems involved in construction of concrete dams are those resulting from bedrock imperfections that escape disclosure by conventional exploration methods. Often these imperfections are of sufficient magnitude to introduce costly changes, especially when their presence is discovered only after foundation excavation is well in progress. Bedrock flaws most frequently camouflaged may be ruptures resulting from the enormous stresses to which rocks have been subjected, or they may be planes or zones of weakness related to chemical alteration and underground erosion. Obviously, detailed information on their location, dimensions, and structure is important, as these factors can affect the stability of a dam and the security of life and property downstream. Their discovery and appraisal entail extensive subsurface exploration. At present the most economical exploratory tool available to geologists and engineers is the small-diameter diamond core drill by means of which cores of the foundation bedrock are recovered for examination and testing. All too often, however, these samples fail to disclose minor foundation flaws that may be of major importance before a structure is completed. As a result, the small-diameter drillings are supplemented generally by more reliable but much more costly shafts, tunnels, or large-diameter calyx drill holes that permit the investigator to examine the foundation rocks in place. It was to reduce the number and cost of these expensive and time-consuming investigations, as well as to obtain more complete information on rock structure from the smaller borings, that the NX borehole camera was developed. That it has been eminently satisfactory in accomplishing that purpose is demonstrated by its success most recently at the Folsom dam, under construction on the American River, 23

Jan 1, 1955

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By Wilson B. Emery

The discovery well in the Rock River field, in Carbon County, Wyoming, came in May 1, 1918. The field is on a large anticline having more than 1500 ft. of closure and production is obtained from three sands of the Dakota group. At its peak, production approximated 10,000 bbl. daily and is now averaging 2200 bbl. Total production to Jan. 1, 1930, exceeded 12,500,000 barrels. So far as known to the writer, Rock River was the first light oil field in the Rocky Mountain region to be produced under what we now term unit operation. Though this type of operation was not popularly acclaimed by the oil industry, the Federal Government and the public until many years after the inception of development at Rock River, the officials of the Ohio Oil Co. when acquiring this property were fully cognizant of the economies to be effected by unit ownership and the consequent elimination of competitive drilling and producing of wells, and had this in mind at the time. Thus unit management was introduced in this field at an early date by this company. Area and Management Fig. 1 shows the location of all wells drilled on the Rock River structure and the outline of the productive area as now defined, which amounts to 1380 acres. The hachured line indicates the area now under unit ownership; originally a much larger area was so owned but leases have been canceled as progressive development indicated their lack of oil. The management and operation of the entire productive area is handled by the Ohio Oil Co., which owns the majority working interest. The Continental Oil Co. with a 20 to 35 per cent. interest in much of this acreage, and smaller interests owned by others in some of the leases, constitute the remainder of the ownership. The fee rests in the State of

Jan 1, 1930

By C.A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By C. A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

EDMUND NEWTON, Minneapolis, Minn. (communication to the Secretary?).-In discussing the question of the deoxidation of steel and material suitable for performing this function at the end of the heat, it would seem logical also to include the question of prevention of oxidation in the steel or the formation of iron oxide, FeO. I refer to the use of manganese in the basic open-hearth and basic Bessemer processes. The advantages of high manganese in pig iron for these processes have evidently been clearly understood in Germany for a number of years, although little has been written in regard to the exact manner in which the benefits are obtained. In this country, while we make no steel by the basic Bessemer process, our basic open-hearth process is becoming more and more important. Until 10 years ago, in this country, manganese in the pig iron for this process was considered of little value and by many writers it was spoken of as a disadvantage. During the past 10 years, however, in certain parts of the United States, higher contents of manganese in basic pig have been used with considerable success, although there is apparently nothing in our technical literature to show the reasons for this trend. A German book, "The Basic Open-Hearth Steel Process" by Carl Dichmann does, however, offer an explanation. Dichmann says that if the charge for either of the above-mentioned processes contains 3 per cent. of manganese or above, satisfactory steel.

Jan 6, 1917

By T. B. Counselman

An iron blast furnace of 1000 tons daily capacity will produce a 100,000 cu. ft. per minute of blast-furnace gas. This contains a 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. gas is used primarily for heating the stoves of the blast furnace, secondarily, under boilers, for steam production. Occasionally it is used in gas engines. The raw gas coming out of the furnace carries about 10 grains of dust per cubic foot of gas, under best operating conditions. With furnace "rolling" or slipping, this quantity may temporarily be gre increased. This dust would, of course, deposit on the checkers o: stoves, or plug the burners under the boilers; therefore the gas : be cleaned. Flow Sheet The first step in the cleaning operation, as shown by the flow s Fig. 1, is a dry dust catcher, of which there are several forms, partially cleaned gas next goes to a primary wet washer, where v sprays knock down most of the solid particles. If further cleani desired, the gas may then go to electrical precipitation. Again, the removed is collected in water. Dry dust catchers reduce the dust col from 10 grains to between 4 and 6 grains per cubic foot, and rec roughly half of the total flue dust in the gas. The wet washers rea most of the remaining dust, reducing the dust content to about 1/4 per cubic foot. Electrical precipitators, if used, further reduce the content to about 0.01 grain per cubic foot of gas. The flow sheet s the dust content of the gas at various steps in the treatment and als content of solids in the water. It should be noted that some plant less water on the primary wet washer than indicated, and that ofte solids content of the scrubber water will be 300 grains per gallon, or much higher. Reasons for Recovering Flue Dust.—There are two main incentive recovering flue dust from the scrubber water: (1) the value of the (2) stream or lake pollution, where such a reason applies.

Jan 1, 1937

By D. L. Johnson

Only general treatment of a subject of such scope can be given in a short paper, therefore, except in a few instances, statistics and descriptions of specific installations are omitted. The earlier applications of electricity to the production of petroleum in the Mid-Continent field were widely separated chonologically, each holding a special interest, and each contributing greatly to the present development. Electric Pumping One of the first installations of electric pumping was on a lease near Jenks, Okla., in the Arkansas River bed, where a difficult problem was solved by the use of motors. The Arkansas River had frequent flood periods which interfered seriously with the use of jacks and pull rods. Small piers were built with old casing used as piling, and upon these were set small jacks driven by 3-hp. squirrel-cage motors. The starting switches were located on a bank and the power was furnished by a small generator, which was driven by an oil country gas engine. This installation was made in 1913 and is, I believe, still in satisfactory operation. In 1914, the Cushing field came in and the Hill Oil & Gas Co. electrified its Shamrock property, using eight-pole Star Delta motors, rated at 10 to 30 hp. and belted through countershafts to the band wheel. Power was furnished by a small generating plant consisting of two 135-kw. machines, gas-engine driven. Considerable difficulty was experienced in the early operation of this station because of low voltage. It is characteristic of small alternating-current generators that voltage regulation will be poor with widely fluctuating loads. This field had three producing sands, and a number of wells were redrilled with the motors, and this, together with a great deal of swabbing, was responsible for the bad load conditions. However, when the wells had settled down to steady operation, the electric equipment functioned satisfactorily, and continued in use as installed until a few years ago when the present owners contracted for service from a central-station company and shut

Jan 1, 1928