Search Documents

INTERNATIONAL ENGINEERING CONGRESS This Congress will be held under the auspices of five National Engineering Societies, of whi h the Institute is one. The sessions will be held in 11 sections and the proceedings will be published in 10 volumes of 500 pages each, of which Volume 8 will contain the papers and proceedings on Mining Engineering and Metallurgy. The membership fee of $5 will entitle the holder to the volume of General Proceedings and Index, and, in addition thereto, any other single volume chosen. Other volumes may be subscribed for according to a sliding scale depending upon the number of volumes taken. The Institute will have a meeting in San Francisco during 1915, and it is desirable for our members to join the International Engineering Congress at in early date in order that their support of the enterprise may be given in its early stages, when it is most needed.

Jan 2, 1914

By Z. F. Oszter

This paper discusses the materials handling problems encountered in cement plants in the areas of raw and finished product grinding and cement storage. It illustrates by examples taken from actual installations, how optimum feed rate is maintained in grinding circuits with properly applied bin dischargers (vibrating hoppers, Mexican feed boxes and aerated bin bottoms) for materials with high moisture content and/or difficult handling characteristics. Initial operating problems with the equipment will be discussed and maintenance requirements will be indicated for comparison purposes. In a modern cement plant, properly functioning bins and feeders are as essential as process control, for no process control system, however sophisticated, can perform efficiently if raw materials do not flow into the plant processing facilities at the required time and rate. Most materials used in the manufacture of portland cement - such as silica sand, iron ore fines, crushed limestone, gypsum, clinker or cement itself-have difficult handling characteristics under specific conditions. High moisture content or even dampness due to condensation may create bin hang-ups, arching and ratholing, all of which result in improper functioning of the feeders or proportioning equipment. The occurrence of these problems in existing cement plants spurred a search for the corrective devices discussed in this article. The equipment investigated included bin dischargers in the form of vibrating hoppers for moist raw materials, Mexican feed boxes for clinker and aerated bin bottoms for cement. Operating experience with different types of bin dischargers showed that the actual performance of some did not come up to the expected level under prevailing operating conditions. The aim of this paper is to record the results of this experience and there- by aid designers and/or operators in selecting the most suitable equipment for their requirements. BIN DISCHARGERS (GENERAL) A discharger is a device that causes stored solids to flow out of a hopper without metering the rate of flow as a feeder does. The investigation discussed here encompasses the following types of bin dischargers used in a cement plant: (1) vibrating hoppers (horizontal motion), (2) whirlpool hoppers (horizontal and vertical motion), (3) aerated bin bottoms (air fluidization), and (4) Mexican feed boxes. Most of the bins used in the cement industry are of the plug flow type. Raw materials with difficult handling characteristics such as high moisture content may cause flow problems when fed through small openings (12 x 18 in.), even if two walls of the bin are vertical.' The most appropriate solution to these flow problems would be the installation of separate mass flow bins for the different materials such as silica sand, iron ore fines, crushed limestone and gypsum, with each bin correctly designed from test data obtained by measuring the flow properties of representative samples. However, limited storage capacity and plant space usually preclude this approach. Quantitative design of bins for flow based on measured flow properties of representative samples of the bulk solid to be handled is no longer an "engineering art," thanks to the basic research done on the flow of bulk solids in bins during the last decade.2, Where space limitations exist, however, or where improvements are being sought for equipment already installed, bin dischargers offer a satisfactory solution to flow problems. They can be applied effectively under flat-bottom bins or mounted to existing plug-flow bins with very little modification to these facilities. In both the foregoing cases, plug flow will be maintained, but the flow channel will be considerably increased so that it is larger than the discharger's bin-side diameter, and material flow can be sustained if the discharger is correctly selected. The main purpose of a bin discharger is to draw the bulk solids across the whole area of the bin outlet, to make the opening fully effective. As long as the bin-side opening of the discharger is large enough

Jan 1, 1969

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By K. H. Heino

Two 200 T/da Lurgi Turbulent Layer fluid-bed roasters have been in operation at Canadian Electrolytic Zinc Limited since 1966. Zinc concentrate containing 52-54% Zn, 9-11% Fe,31-33% S is treated to produce calcine containing 60-62% Zn,10-12% Fe, .l-.3% S as sulphide and .8-1.2% S as sulphate. Each roaster train comprises a waste heat boiler, two cyclones in parallel and a two-field electrostatic precipitator. Distribution of calcine collected is 10-15 percent from bed overflow, 55-65 percent from boilers, 20-25 percent from cyclones and 2-6 percent from precipitators. A Monsanto designed contact plant produces acid at a rated capacity of 365 T/da (100% H2304 basis) from roaster gases diluted to 7.0-7.5% S02. The process steps are gas cleaning and cooling by weak acid scrubbing, acid mist removal in electrostatic precipitators, gas drying in 93.5-96.5% H2304, conversion of sulphur dioxide to sulphur trioxide in a four-pass converter containing vanadium pentoxide catalyst, and absorption of the sulphur trioxide in 98.1-98.3% H2S04. Product acid is 93.2% H2S04. Conversion efficiency is 97-98 percent and overall sulphur recovery from concentrate is 87-90 percent. The adjacent fertilizer plant has a capacity of 135 T/da of P205. The products are 54 percent phosphoric acid, run-of-pile triple superphosphate, and diammonium phosphate. The plant is of Ugine-Kuhlman design and consists of an air-cooled multiple tank reactor, a tilting pan filter, and a forced circultation vacuum evaporator. Triple superphosphate is made on a continuous belt and partially cured in a rotary dryer. Diammonium phosphate is produced by ammoniating phosphoric acid in a single stage reactor. The slurry of ammonium phosphate is granulated in a blunger and dried.

Jan 1, 1970

By F. R. Morral, K. T. Aust

The preferred orientation and earing characteristics of ZS aluminum were studied. An empirical correlation was obtained relating earing behavior and variation of mechanical properties for face-centered cubic metals. Strain-ratio mecsurements for ZS were found to be in good agreement with Hill's theory of plastic anisotropy. DIRECTIONALITY in sheet metals may be revealed by earing in a cupping test, or by the variation of mechanical properties of tensile specimens taken at different angles to the rolling direction. However, no simple correlation appears to exist between earing and variation in mechanical properties in metals and alloys studied.1-5 Aluminum of commercial purity (known as 2S, with a specified minimum of 99.0 pct Al) cast by the direct casting process was chosen in the present investigation since ears at 45° or 0°, 90° can readily be obtained. Preferred orientation is often the principal cause of uneven metal flow, such as earing, and variation in mechanical properties. Consequently, the preferred orientation characteristics of 2s aluminum were initially studied using both X-ray diffraction and micrographic techniques. The variation of mechanical properties with angle to the rolling direction was next determined in an effort to clarify the apparent lack of correlation of earing behavior with mechanical properties for face-centered cubic metals. Strain-ratio*5,8 measurements were finally conducted to determine first, if the maximum values of the strain ratio occurred at the earing positions, and second, if Hill's theory of plastic anisotropy7 is applicable to other face-centered cubic metals such as aluminum. Detailed treatments, working, and heat treating are not given in this paper since this study is not concerned with the methods to produce earing, but to correlate earing with other properties and characteristics of the material. The percentage of earing was measured using the formula specified by the x—Y Aluminum Association, -------- X 100 = pct earing, where x is the height of the ear and y is the height of the valley from the bottom of the cup. Preferred Orientation Characteristics of 2S X-ray Studies: Beck and coworkers8 have determined that the rolling texture of 2s after 95 pct cold reduction may be approximately described by four equivalent ideal orientations near (123) [121]. Also, the recrystallization or annealing texture of 2s aluminum consists of four components of the (123) [l21] type, retained from the rolling texture, and of a (100) [001] or cube texture component." Fig. 1 illustrates the typical appearance of deep drawn earing cups with the corresponding X-ray diffraction patterns. The X-ray patterns were taken with copper radiation using the structure-integrating method'" in which the specimen is scanned during the X-ray exposure. The rolling direction was vertical and the rolling plane was perpendicular to the horizontal X-ray beam. It was found that an increase in the retained rolling texture component resulted in a greater 45" ear height, while an increase in the recrystallization texture component (i.e., cube texture) caused greater 0°, 90° earing. X-ray diffraction studies of 2s cold rolled to final thickness followed by a final anneal have shown that the rolling texture, and also the retained component of the rolling texture after annealing, are increased with greater cold-rolling reduction. The preferred orientation characteristics of 2s sheets given an intermediate anneal between cold rolling followed by a final anneal were found to depend on the position of the intermediate anneal during cold rolling. For instance, three identical samples of 2s homogenized ingot, each 1 in. thick, were given the following cold-rolling and annealing treatments: 1—50 pct reduction, intermediate anneal, 96 pct reduction to 0.020 in. and a final anneal; 2—75 pct reduction, intermediate anneal, 92 pct reduction to 0.020 in. and a final anneal; and 3—90 pct reduction, intermediate anneal, 80 pct reduction to 0.020 in. and a final anneal. The intermediate and final annealing treatments consisted of a 70°F per hr heating rate, held 6 hr at 800°F and air cooled. Typical X-ray patterns after each of these treatments are shown in Fig. 2. It was evident that after treatment 1, the retained rolling texture component predominated; after treatment 2, the retained roll-

Jan 1, 1954

By Ellis Clark

THE greater portion of the brown ore in the vicinity of Easton, along the north slope of the Lehigh Mountain or Durham range of hills, is obtained from mines instead of from open cuts or quarries, as is the case in the ore-beds in the western part of Northampton County, in Lehigh County, and in Berks County. The reasons for this method of procedure are various, and the principal causes of the shaft and regular mine system of working being adopted instead of the open air cuts, are : First, the large amount of stripping that would be necessary, as the richer and more valuable portions of the ore do not appear to be found as near the surface as those in other portions of the Kittatinny valley; second, the occurrence of the ore in regular beds, interstratified with the clay, and, to a less extent, in pockets or erratic deposits, as is the case in the mines of Lehigh County; and third, on account of many of the mines being situated at the immediate base of the Lehigh Mountain, where the surface water would be in such large quantities as to be with difficulty handled, and where the subsequent caving in of the sides of the open cut would be almost certain to expose the gneiss rock, which is water-bearing, the large quantities of water coming from which would probably drown out the ore-bed. Shafts, and a regular system of gangways and mining are therefore required by the configuration of the surface, the depth of the deposits and their geological structure. The ordinary size of the shafts is about four feet square, but where an extensive plant of pumping machinery is required the size may be increased to eight feet by six, with two compartments for the hoisting and pump-shaft respectively. A man-way, consisting of ladders with rests at intervals of twenty or thirty feet, is comprised in the pump-shaft, the wire rope being used for purposes of ascent and descent only in exceptional cases, on account of accidents which

Jan 1, 1879

By Avnulf Muan, P. V. Riboud

The effect of Cr2O3 on melting relations of iron oxide at oxygen pressures slightly above those prevailing in contact with metallic iron has been determined. Liquidus and solidus temperatures of wüstite are raised by the addition of Cr2O3, from 1385°C for pure iron oxide to 1420°C at the peri-ledie point where wüstite, iron chromite, liquid, and gas coexist in equilibrium under the atmospheric conditions used in the present investigation (CO2/H2 = 1). It has been shown in a previous investigation1 that the liquidus and solidus temperatures of iron oxide are drastically increased by the addition of Cr2O3 under the relatively oxidizing conditions prevailing in air. This is to be expected in view of the easy substitution of cr3+ for Fe3+ in crystalline oxide structures which are stable at high oxygen pressures, as demonstrated for instance by the completeness of the solid solution series Fe2O3-Cr2O3 at high temperatures (>1000°C). The stable phase of iron oxide at oxygen pressures approximating those prevailing when metallic iron is present is wüstite. This phase, although commonly represented by the simplified formula FeO for sake of convenience, in reality has a defect structure in which a part of the iron ions are present as Fe3+. It is to be expected that at least a limited amount of cr3 ions will substitute for Fe in this structure when Cr2O3 is added to wüstite. Depending on the ease of this substitution in comparison with that of cr3 substitution for Fe in iron oxide-Cr2O3 liquids under the same atmos- pheric conditions, the liquidus and solidus temperatures of wüstite may increase or decrease upon addition of Cr2O3. The methods of establishing these melting relations and the results obtained are presented in the following. I) EXPERIMENTAL METHOD 1) General Procedure. The quenching technique was used in this study. Oxide mixtures were heated at chosen constant temperatures in an atmosphere consisting of equal parts of CO2 and H2 until equilibrium was established among gas and condensed phases. The samples were then quenched in mercury to room temperature, and the phases present were determined by microscopic and X-ray investigation. 2) Preparation of the Mixtures. Starting mixtures were prepared by weighing and thoroughly mixing Fe2O3 and Cr2O3, or wüstite and Cr2O3. The Fe2O3 and Cr2O3 used were "Baker Analyzed" reagent grades, whereas wüstite of composition was synthesized by reducing Fe203 at 1325°C in an atmosphere consisting of equal parts of CG andHz. In order to avoid contact with crucibles, the equilibration runs were made with small pellets suspended from thin (-0.004-in.) platinum wires. Mixtures made from FOs and Cr203 were readily pelletized at a pressure of 500 atm in a 9.5-mm die, whereas mixtures made from wüstite and Cr203 when treated identically were too weak for handling. In order to obtain a stronger product, these pellets were sintered by heating for 2 min at -1200°C in the same atmosphere as was subsequently used for the equilibration runs (CG/H2 = 1:1). During the sintering, these pellets were wrapped in thin (0.0004-in.) platinum foil, which was stripped off before the equilibration runs. In order to reduce the time needed for equilibrium to be attained, preliminary equilibration of relatively large pellets of each mixture was carried out at -1200°C for 4 to 12 hr. Smaller pellets

Jan 1, 1964

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

By R. M. Waterstrat, B. N. Das, Paul A. Beck

The central region of the Ti-Mn system was studied by means of x-ray diffraction and metallography. The following intermediate phases were found: an MgZn2-type Laves phase having a wide range of homogeneity, the p-phase of unknozvn structure, and the + -phase with a large tetragonal unit cell, stable at 930°C and lower temperatuves. MaYKUTH, Ogden, and jaffee1 determined the soh-inh bility limits of manganese in and titanium. They also confirmed the structure of the intermediate phase TiMn2 which was previously identified as a Laves phase of the MgZn2 type.2 In the equiatomic region they found an additional intermediate phase, y, which presumably formed by a peritectic reaction at approximately 1200°C. This last observation was disputed by Rostoker, Elliott, and McPhers0n,3 who reported the formation of TiMn by a peritectoid reaction between 900" and 1000° C, but found no evidence of any intermediate phase other than the Laves phase at higher temperatures. Elliott and Rostoker4 reported furthermore that the X-ray diffraction pattern of TiMn could be identified as that of a o phase, although their data were not consistent with this inter~retation. Margolin and Ence6 presented X-ray diffraction data for the and TiMn, phases, and obtained metallographic indications for the existence of additional intermediate phases. They concluded from metallographic observations that two Laves phases are formed, separated by another phase, designated as &. A phase diagram for the Mn-Ti system has recently been published by Savitskii and Kopetskii,' which shows considerable disagreement with the work of Hellawell and Hume-Rothery,' in particular with regard to the terminal solid solutions based on the allotropes of manganese. The present investigation was undertaken primarily to clarify the phase relationships in the equiatomic region of the Ti-Mn system. The metals used in preparing the alloy specimens Were iodide titanium and electrolytic manganese, the latter having a nominal purity of approximately 99.9 pet. The electrolytic manganese was covered with a thick coating of a brown manganese oxide which was reduced by heating the manganese flakes for several hours at a temperature of 1100°C in an atmosphere of dry hydrogen. Three alloys, see Table I, were made using sponge titanium and manganese not treated in hydrogen. The alloys were prepared by arc-melting in an atmosphere of helium or argon. The composition of each alloy was calculated by assuming that the entire weight loss during melting was due to evaporation of manganese. Subsequent chemical analysis of certain alloys indicated that the compositions calculated in this manner were usually correct within 1.4 pct, as shown in Table I. All alloy specimens were wrapped in molybdenum foil before sealing them in silica tubes containing argon at a pressure of 1 atm at the annealing temperature. After quenching in cold water, the alloy specimens were bright and clean, with no evidence of any surface reaction. The alloys listed in Table I were examined metallographically, using an etchant consisting of 20 pet HNO3, 20 pet HF, and 60 pet Glycerine. powder for X-ray diffraction examination was prepared by crushing a portion of each annealed alloy

Jan 1, 1962

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

* Kennecott Copper Corp. gets Charles R. Cox as president on Jan. 1. Mr. Cox is resigning his position as president of Carnegie-Illinois to take the new post with Kennecott, left vacant by the death of Mr. Stannard in September. •The ECA signed a contract in December to advance X3,600,000 to Newmont Mining Corp. to aid development of lead and zinc mines in French Morocco. The funds are to be repaid in lead and zinc for the United States' stockpile over a period of seven years. The mines are owned by the Societe des Mines de Zellidja, with which organization Newmont is associated. • Under the direction of John M. Brooks, Jr., general manager, the Matahambra mine in Cuba, will probably produce sufficient tonnage to make 4 million lb of copper per month during 1950. The grade is presently running between 7 and 10 pet. •S. H. Ash reports that the fatality rate per million-man-hr for the anthracite industry for 1949, through November, is 0.78. This is 15 pct better than that achieved during 1948, which was the lowest fatal injury rate in coal mining history. The first full year on record without a major disaster was recorded in 1949 (p. 34). •The Atomic Energy Commission has authorized the production of 200 lb of uranium metal for use under AEC license in non-Commission research projects. •A national survey of projected 1950 purchases of new machine tools, machine tool accessories, materials handling equipment, etc., just completed by the American Society of Tool Engineers reveals that, of the companies reporting, 80 pct state that they plan to buy either more equipment or the same amount as in 1948. • Armour Research Foundation is conducting investigations for the use of clay and shale deposits to make lightweight aggregates. The material is heated until it expands and forms material suitable for mixing with cement which it is hoped will be lighter, stronger, have better insulating qualities and will lower the cost of concrete. •In the first six months of 1949 the bituminous coal miners' average hourly earnings were $1.94 -as compared with X1.392_ national average for all manufacturing. Average annual earnings of full-time employees in the bituminous coal mines in 1948 were $3387 as compared with $2809 for all industry. •LaSalle Business Bulletin reports: "year ends on a rising trend in industry and trade ... nearly record-breaking demand from almost all sources keeps business high... most indicators but little below postwar peak... forces keeping activity high arestill powerful--changes in general business conditions likely to be slow and moderate." •Office of Internal Trade of the Commerce Department requests that technical data significant to the national security which is to be sent outside of the United States be submitted to it for an official opinion on the desirability of transmitting such information. This voluntary compliance program is part of our national security control. • Blast furnace slag reduced to 12 to 16 mesh is being used for sanding track at the Mont Coal mines of Armco. The slag replaces silica sand which caused silicosis. It has proved so effective and cheap that tests are being made to use the slag for rock dusting.

Jan 1, 1950

Discussion of the paper of E. J. Hall and C. W. Drury, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1059 to 1066. A. M. SMOOT,* New York, N. Y. (communication to the Secretary +) :-The nails method is given in many text books on assaying as a standard method for gold or for gold and silver in ores. It appears to be taught in the laboratories of technical and scientific schools as a standard method, and to some extent it is used by assayers in actual practice, although the class of ores to which it may be applied is limited to those free from reducible metallic compounds, the metals of which would enter the lead button. The experiments of Messrs. Hall and Drury show the inaccuracy of this rnethod for silver, in heavy sulphides, but not so clearly the short-comings with regard to gold. It seems certain that low silver is caused by the solubility of silver in iron-alkali sulphide as compared with its solubility in molten lead; that is, silver is distributed between iron-alkali sulphide and metal in the charge in proportion to solubility at the particular temperature of the fusion. Lead is a fixed quantity in these assay charges, but iron-alkali sulphide increases with increased sulphur, so the more sulphur in the charge, the lower the silver results.

Jan 11, 1913

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks' and to the precipitation of second phase particles,2'3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these '(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By Joseph W. Leonard

Partition (Tromp) curves, as used in diagnosing problems in coal cleaning equipment, are discussed and classified using five arbitrarily chosen types to represent, on a scale from one to five, system performance. Causes of unsatisfactory Tromp curves for various cleaning units, ranging from operational inadequacies to problems best corrected by the equipment builder, are analyzed.

Jan 1, 1982

By Jay A. Carpenter

FIRST of several sessions at the Annual Meeting devoted to mining methods was a joint program with the Coal Division devoted to the use of Diesels underground. Fred W. Stiefel, in the first paper, stressed the saving in original cost and in operation. Wm. B. Harris then presented the paper of which he was a joint author, and S. H. Ash stressed the poisonous nature of nitrous fumes from Diesel engines even in minute quantity. Determination is difficult but in exhaust gases they are present in amount two to five times that of carbon monoxide. Jay A. Carpenter, in the closing paper of the session, stated that state laws in general prohibit the use of Diesels underground, and that almost all mine inspectors are opposed.

Jan 1, 1942

By John J. Collins

The plight of the Japanese mining business is pitiful. Coal mines were given the highest priority for all materials they needed, yet between the end of the war and June 1948, the government was obliged to subsidize them to the extent of 22 billion yen, this being the difference between the consumer's price and the producer's price. Most of the metal mining companies have been operating at only one fifth to one third of war-time production rates, and financial losses have been terrific. The chief difficulties have been a plethora of office workers and a dearth of equipment, supplies, and miners. The principal material needs at metal mines are steel rails. cars, plates, nails, rubber hoses, and belting, to say nothing of modern core drills which are totally lacking. Until recently the great shortage was in coal; for lack of fuel the smelters and factories failed to produce the very metals and equipment now needed to operate the mines. Nation-wide shortages have created a monstrous inflation of prices throughout all the economy, currently amounting to 200 times the prewar figures. For example, the price of copper ranged from 500 to 900 yen per metric ton for many years until 1937, but in mid-1948 producers were

Jan 1, 1949

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916