Search Documents

By Nicholas J. Grant, Italo S. Servi

Extensive data of minimum creep rates and rupture times for high purity and commercial aluminum confirm the existence of a transition range from the low temperature-type to the high temperature-type behavior. The data are analyzed in line with the suggested theories of deformation of metals. CONSIDERABLY more work has been done on the rupture and creep behavior of commercial alloys than on the less complex, high purity metals. As a result, certain fundamental behaviors are overlooked. One of the lesser known variables affecting the high temperature behavior of metals is the impurity content (or alloy content). Impurities are known to affect strongly the recrystallization temperature, electrical resistivity, and other properties of metals, but the effect on creep and other high temperature mechanical properties has been determined for very few materials. In view of these facts aluminum appears to be a fairly ideal metal, since it is available in a wide range of purity contents from 99.995+ down through the 2s (99.0 + Al) and 3s (1.2 Mn) grades in small steps. It is highly resistant to oxidation and other surface instabilities, leaving recrystallization and grain growth as virtually the only instabilities. Control of grain size is also well standardized. Limited data on the creep of aluminum have been obtained by Dushman et a1.l for high purity aluminum; by Sherby2 on 2s aluminum of variable grain size; and by Dorn and Tietz³ on cold-worked 3s aluminum. Experimental Procedure The apparatus consisted of a constant stress, creep testing unit similar to the type described by Hop-kin.' The specimens were held at temperature for 30 min before loading. The loading time was less than 2 min. Factors affecting the accuracy of the data were: 1-—the temperature gradient and control, ± 3°F; 2-the stress determinations, ± 1.5 pct; and 3—elongation measurements (1 in. gage), ? 0.001 in. Three grades of aluminum were tested: 1— high purity (99.995 pct Al), 2—2s (99.3 pct Al), and 3—3s (98.2 pct Al). The spectrographic analyses of these materials are reported in Table I. The specimens were annealed then electropolished in a perchloric-acetic mixture before testing. Data on heat treatments and grain size obtained appear in Table 11. The entire creep curve was determined for almost all of the tests. A few tests were interrupted after the beginning of the third stage of creep, and in these cases the rupture time was estimated. Experimental Results Constant stress creep-rupture testing gives a much longer, more accurately measurable second stage of creep than constant load testing. This behavior is in agreement with the results obtained by Andrade for lead (see Fig. 1). If the test is run to completion, the third stage of creep appears as soon as stress intensification occurs. In the case of specimens which fail in a ductile manner, the stress intensification begins when the sample starts "necking". This differs from the "high temperature brittle" specimens in which the stress intensification is caused by intercrystalline cracking. These specimens

Jan 1, 1952

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By B. C. Craft

Development and exploratory work in Mississippi during 1934 was rather active, resulting in the expansion of the proven area and the drilling of a number of important wildcat wells. Mississippi showed a decrease in drilling operations during 1934. There were 36 completions from 18 counties during this period compared with 58 completions from 22 counties during 1933. There was a considerable decrease in activity in the Jackson gas field in Hinds and Rankin counties with only 9 completions, resulting in 8 gas wells and 1 dry hole compared with 17 gas wells, 2 oil wells and 7 dry holes during 1933. Leasing and geophysical work was reported from several sections of Mississippi last year. Extensive exploration and drilling were carried on in Lamar, Hancock, Pearl River, Greene and Stone counties and on the flanks of the Jackson anticline. Exploration will be continued in these areas during 1935. Four important wildcats were completed during 1934, all of which were reported as being structurally high, but without having important shows of oil or gas. These tests were: Hix and Germany's, J. J. Newman Lumber Co. No. 1, sec. 21-4N.-15W., Lamar County, abandoned at 3520 it. in the Wilcox; United Gas Public Service Company's Davis No. 1, sec. 30-1N.-5W., Greene County, abandoned at 7439 ft.; Gulf Refining Company's May L. Williams No. 1, sec. 33-5S.-17W., Pearl River County, abandoned at 4800 ft.; and Clarke County Oil Company's S. B. Kirkland No. 1, sec. 10-2 N.-16E., abandoned at 4002 ft. in the Eutaw. Another interesting wildcat was Gulf Refining Company's Dantzler Lumber Co. No. 6, sec. 22-4S.-llW., Stone County, abandoned at 7700 ft. (according to reports below the Selma chalk). A total of 114 of the 132 gas wells completed in the Jackson gas field are still producing and have a combined open-flow capacity of 4,145,-696,000 cu. ft. Four of the abandoned gas producers were never connected to the lines. The open-flow capacity of three wells in the Amory field is approximately 1,000,000 cu. ft. Producing against a line pressure of 50 lb., the demand during December greatly exceeded the capacity.

Jan 1, 1935

By Edgar A. Scholz, Attilio G. Spat

The rapid worldwide increase in labor costs, prices of goods and services, and the rising tide of economic nationalism do not bode well for the future of mineral exploration and the mining industry. The increasing complexity and difficulty involved in finding economic mineral deposits makes these trends particularly significant. A comparative cost analysis of domestic and foreign exploration projects which developed into mines during the period 1960-74 may be useful in indicating the general nature of exploration expenditures as these trends continue. This analysis is based on a survey of 18 US and Canadian mining companies. Due to the inexact nature of exploration expenditure data, plus the fact that no two mining companies follow the same system of cost allocation, the results of the survey must be considered quite general in character.

Jan 6, 1977

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

Richard Moldenke, New Pork, N. P. (communication to the Secretary*):—Iu following the discussion of the specifications for cast-iron and finished castings, I mas strongly impressed with two points which might be ventilated to advantage more fully from the view of the practical foundry-man. First, the reasons why only silicon and sulphur were specified and not phosphorus, manganese and carbon; and second, why but little was said concerning the presence of iron oxide in the material.

Jan 1, 1905

By C. G. Dunn, W. W. Martin

Various X ray diffraction techniques have been developed for determining orientations of crystals. Transmission and back-reflection Laue methods1,2,3 in particular have been found to be very useful. In many applications, however, a need still exists for a simplification of the details of analysis so that orientations can be determined more rapidly, and operators with little or no training in crystallography can be easily instructed in the necessary procedures. Filling this need in part is a system of analysis that has been in use for several years in the Metals Section of the Laboratory, General Electric Co., Pittsfield, Mass. This method is an extension of the one of Majima and Togino,4 which uses fifty-five indexed standard transmission Lauemams to cover the entire range of crystal orientations. Greater rapidity in determining the orientation of a crystal is achieved by using a slightly larger set of standard Lauegrams and by systematizing the steps followed. This system of analysis in its present form constitutes the subject matter of the present paper. Although the method uses transmission X ray Laue patterns, many of the operations are applicable to the analysis of back-reflection Lauegrams. Very briefly the method is based on the fact that Bragg and azimuthal angles for two or more identified Laue diffraction spots completely determine the orientation of a crystal, and standard Laue photographs of the Majima and Togino type provide a ready means for identifying Laue spots. After a preliminary analysis, which consists of identifying the pattern in terms of one of the standard patterns, a correctly marked Lauegram is selected to carry out the final analysis. From measured Bragg and azimuthal angles, the normals (poles) of the reflecting planes for the selected Laue spots are located on a stereographic projection and the orient.at.ion of the crystal determined (in terms of the positions of cube poles for example) by a few additional operations on a \I1ulff net. The actual procedure followed will be illustrated in detail after a brief treatment or X ray problems connected with orientation determinations and a discussion of useful principles and techniques. X Ray and Plotting Problems RELATIVE ADVANTAGES OF BACK-REFLECTION AND TRANSMISSION LAUE DIFFRACTION METHODS In the back-reflection Laue method it is easy to make a direct measurement of the tilt of a zone of Laue spots. Specimen thickness also is generally no problem. In the case of thin specimens, however, the time of exposure is less for the transmission Laue method. For example, with silicon ferrite this advantage holds up to a thickness of 0.6 mm if tungsten radiation at 40 kv peak voltage is used. Furthermore, the transmission photograph represents the entire thickness of the crystal whereas the back-reflection picture represents only a surface layer (a thickness of less than 0.05 mm for silicon ferrite), the deeper layers supplying a negligible amount to the diffraction pattern. If a crystal is distorted, the transmission Laue pattern gives more information particularly with regard to the orientation of the crystal and the overall amount of spread in orientation. Finally a 3 1/4 X 4 in. film suffices for transmission photograms; a 4 X 5 in. or 5 X 7 in. film with a central hole is needed for back-reflection patterns Not only is the manipulation of film easier because of the size of film, but

Jan 1, 1950

By Carl Lee

CHICAGO in the last week of June fulfilled all its promises to the visiting engineers except one. This holds true with respect to the activities of the Regional Meeting of the A. I. M. E. in particular and of Engineers' Week in general. No one expected to find much of the beautiful in the outward aspects of the Fair-the Century of Progress Exposition, to be more formal; but they expected novelty, color, and startling lighting effects at night, and they were in no sense disappointed. It has been said that the architecture is a portent of the style of the buildings of the future; most who have seen the Fair hope that this forecast will prove inaccurate. As to the exhibits themselves, they are splendid. They are in keeping with the theme of the Exposition-a Century of Progress in science, in engineering, in the industries based upon them. No attempt will be made here even to suggest the exhibits that are most interesting. There are plenty for every one; and any member of the Institute who has the opportunity should by all means visit Chicago before the end of October.

Jan 1, 1933

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economically entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transportation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotivcs are replacing coal in some places, where railroads operating high-speed passenger trains are willing, temporarily at least, to pay a premium for the fuel that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly established, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be rcquired in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bituminous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1936

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economically entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transportation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotivcs are replacing coal in some places, where railroads operating high-speed passenger trains are willing, temporarily at least, to pay a premium for the fuel that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly established, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be rcquired in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bituminous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1936

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By H. R. Hanley, Charles Y. Clayton

ONE of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi¬menting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electrodeposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electrodeposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect oil tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1938

By Manning W. Cox

Van Stone mine area is situated at the head of Onion Creek on the northwest flank of Gillette Mountain, Stevens County, Washington. The di strict was found during World War I, but the mine did not come into production until 1952. Production to the end of 1965 was 2,242,960 tons of ore that yielded 10,700 tons of lead concentrates and 120,000 tons of zinc concentrates. The area is part of the Selkirk Mountains Zinc-Lead Belt, or Kootenay Arc, extending from near Revelstoke, British Columbia, to Colville, Washington. A thick but incomplete section of Paleozoic marine formations occurs in the Kootenay Arc and is overlain by marine and continental Mesozoic formations. Both are invaded by Late Mesozoic-Tertiary batholiths. The belt is characterized by open complex folding and extensive high-angle and local thrust faulting. Principal ore deposits occur in the highly deformed carbonate rocks of Cambrian age-the Maitlen (Laib) and Metaline formations. The Van Stone mine occurs along a steeply S-shaped fold lying between the Kaniksu Batholith on the west and the Rogers Mountain Fault, a northeast-trending fault on the west flank of the Gillette Mountain Anticline, to the southeast. The fold is cut by northeasttrending faults containing notoriously irregular lamprophyric, diabasic, and pebble dikes. The host rocks, lower Paleozoic dolomites, are decolorized, silicified, and silicated in the mine area. Jasperoid and tremolite are the common alteration minerals. Other gangue minerals are barite, pyrite, brucite, calcite, and, near the batholith, pyrrhotite. Ore minerals are galena, jamesonite, and sphalerite. Ore minerals occur in bunches and pods intergrown with tremolite and jasperoid. Zinc is roughly eight times more abundant than lead. The highest ore outcrops at 3870 feet elevation, and an undeterminable portion has been removed by glacial scour. The lowest drill hole penetration has reached 3220 feet elevation. Oxidation ranges up to several hundred feet in depth and may be most closely related to pre-glacial groundwater circulation. The area of the mine was completely over-ridden by Pleistocene continental glaciers, and the present erosion surface is nearly continuously blanketed by up to 150 feet of glacial outwash.

Jan 1, 1968

By G. F. Loughlin

THE matter of grading Indiana oolitic limestone has been under a cooperative study by the Supervising Architect's office, the U. S. Geological Survey, the Bureau of Standards, and the former Indiana Limestone Quarrymen's Association. As the criteria for grading are necessarily based on a number of geologic and related factors of which those quarrying and using the stone had only imperfect appreciation, the first part of the report is a very elementary account of the origin, structure, and the chemical and physical properties of tie stone, and their relations to durability and utilization, and serves as a foundation for the second part, which discusses grading and pro- poses limits for grades established by the quamymen. Salient features of Part I of a report that has been prepared are the variations in uniformity of stone due to cross bedding, and local uncomformities; the relative prominence of weathering effects on the coarser uneven grained surfaces, and its apparent absence on fine, uniform grained surfaces, although the amount of weathering is the same on each; the attributing "crow feet" (stylolites) to solution under pressure, and the explanation that, whereas the thinnest "crow feet" have no noteworthy effect on weathering quality or strength, the thicker ones are likely to weather out rapidly and to promote splitting; the influence of fracturing on the oxidation of the original gray or "blue" to buff color above the ground water level; the interpretation of chemical analyses and the pointing out that both the gray and buff colors are due mainly to organic

Jan 1, 1929

By Grover R. Castle

INTRODUCTION "Project Financing" or "Project Loans" have become increasingly popular in recent years, and commercial banks are being asked to consider more and more of such financing. However, the analysis of this type of loan is quite different from the analysis of a loan to a financially sound corporation based on the company's balance sheet. For this reason Chemical Bank did a study of project loans in an attempt to be more sophisticated in our approach to them. As part of this study, we examined 29 project financings for which information was available. In this article I shall describe project loans and set forth the guidelines we developed, as an aid to credit officers who might have occasion to analyse this type of financing. DEFINITION OF "PROJECT FINANCING" OR "PROJECT LOAN" The terms "project financing" and "project loan" commonly describe the various methods that banks and institutional lenders use to finance the construction of new projects on a basis whereby payout is anticipated from the revenue stream generated by the project. A project financing often involves a loan to a new entity formed specifically to own the project. The analysis of a project loan proposal is quite different from the analysis of other term-loan proposals since it involves a credit decision based on the review of a projection or forecast rather than of historical earnings and/or it involves the reliance on contractual obligations of third parties. Lenders are asked to assume the added risks associated with project loans because: 1. Project financing may permit a company to obtain additional leverage. It is possible for companies to arrange financing on a project basis that could not be arranged as a direct borrowing. For example, a company may not be permitted to borrow more money directly, due to a limitation in a bond indenture. However, a project financing can sometimes be negotiated on a basis not prohibited by the indenture. 2. Often the sponsors of, or the stockholders in, the project are seeking an off-balance-sheet financing. For example, 11 of the 29 projects in our study were arranged on an off-balance-sheet basis and one showed on the balance sheet as a deferred income item. An off-balance-sheet financing, for the purpose of this article, is a financing which does not show as a direct liability on the balance sheet of the sponsors of or stockholders in a project. 3. Projects are often located in a foreign country. The financing is arranged so that the lenders assume the political risk on the loan because many companies rightly believe that this arrangement affords a degree of insulation from political risk not otherwise obtainable. 4. Many projects are jointly owned by several sponsors. This form of financing lends itself well to a situation where a new entity is formed to own a project and do the borrowing. Project loans can be used to finance a variety of activities including development of iron-ore deposits and associated pelletizing plants; development of coal reserves; construction of pipelines, alumina plants, fertilizer plants and refineries; etc. The specific areas of analysis can be quite different, depending upon the type of project being financed. It is important, therefore, to classify the proposal according to the type of project, and also by the nature of the financing - nonrecourse financing, financing covered by a guarantee of completion and financing supported by an undertaking lasting for the life of the financing. I will discuss each of these types in more detail later, but first, I should like to make some

Jan 1, 1985

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker's data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942