Search Documents

By L. M. Howe, J. Gordon Parr, E. Saarema

THE decreasing solid solubility limit at the titanium-rich end of the Ti-Cu constitutional diagram,' Fig. 1, suggests the possibility that titanium-rich alloys may be age-hardenable. However, results obtained by Holden et al. reproduced in Fig. 2 show that after quenching from 790°C the age-hardening of an alloy containing 1.7 pet Cu is very slight, while a 0.8 pet alloy decreases in hardness, during heat treatment at 400°C. It was believed possible that powder samples of alloys might show different results from the lump samples used by Holden et al., since small particles are often more sensitive to diffusion processes than larger samples. Consequently, a 1.9 pet (by weight) Cu alloy was made by the technique of levitation melting," checked for homogeneity, and filings of 48-65 Tyler screen size were cut from it for aging experiments. The filings were helium-quenched (by a technique described previously)' from 790°C, sealed in vacuo in silica tubes and aged at temperatures of 400°, 450°, and 500°C. Microscopic and X-ray examinations failed to reveal any structural changes during the aging process. This is not too surprising since early stages of precipitation do not usually manifest themselves in ways that are readily detectable by metallographic methods, and the extent of precipitation on overaging a 1.9 pet alloy is very small. However, hardness readings (taken on a Bergs-man micro hardness tester, using a 25 g load applied to a diamond indenter) do show a hardness peak at each aging temperature, Fig. 3. About a dozen readings were taken on each heat treated sample; the highest reading and the lowest reading were ignored and an average taken of the remaining values. In

Jan 1, 1957

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By Richard P. Rothwell

Fires in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it mas not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. Causes of Mine Fires.—Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable then] to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

By T. O. Breitling

Two significant problems In mill design are environmental control and cost reduction. Environmental control is predicted to be 5-10% of total plant costs in some parts of the U.S. Operating and design companies will assign this new "unit operation" a place in the early flow sheets. More advanced environmental control will add to both capital and operating costs, so mill designers will strive to reduce other costs.

Jan 1, 1970

By James J. Bailey

Percussive drills have been in commercial use for many decades. Until relatively recently there was little serious effort to analyze the stresses in such devices in any detail. Within the last few years such analyses have been developed and have been reported by a number of authors.1-4 We present here an investigation of the impact systems of a family of conventional down-hole drills with optimization the objective. We have assumed that maximum drilling speed was the quality most desired and that this was to be achieved within conventional practice. In fact the methods that are demonstrated in principle below can readily be adapted to other percussive devices, whether conventional or not, and to other constraints. SOME PERFORMANCE PARAMETERS FOR PERCUSSIVE DRILLS Consider a percussive drill with an air motor operating with the following parameters: p-supply air pressure a-effective piston area W-piston mass S-piston stroke If we consider a simple (constant pressure) cycle, the following relationships can be derived. The blow frequency [N~ pa lie WS 377]

Jan 1, 1968

By Charles E. Locke

SHARP CONTRAST exists in the reports so helpfully contributed by the individual members of the Milling Committee for this review. Those engaged in the milling of gold and silver ores report great activity, of which some details will be given later. Those engaged in milling ores of base metals report continued depression and little progress. Copper production in the United States is running at about fifteen per cent of capacity. Some Arizona copper mills are closed. Anaconda is milling about 45.000 tons of copper ore per month, and the Utah Copper Co. 35,000 monthly. However, in Canada the International and Falconhridge copper-nickel mills and the Noranda copper-gold mill have increased production. Also the Climax molybdenum mill in Colorado is milling 4000 tons per day. Water shortage from the drought has caused curtailment or complete shutdown of mills in some parts of the West.

Jan 1, 1935

By T. L. Johnston

MUCH has been said and written about deep mine shafts and deep drill holes as man in his search for mineral wealth digs deeper into the earth's crust. Each year some new extra depth is heralded as a record, but with unlimited possibilities of going still deeper. In contrast to "digging deep," "mining high" is limited by the height of the mountains (Mt. Everest being the maximum with its 29,000-ft. elevation) and also by the extent of human endurance. An ex- ample of what might be called near- stratosphere mining in what is probably the highest mine worked by compressed air in the world is seen in a recent project in the Andes mountains of southwestern Bolivia.

Jan 1, 1939

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By P. W. Davies, B. Wilshire

PREVIOUS investigations on the effect of stress changes on the high-temperature creep and fracture behavior of metals have been confined mainly to the testing of complex alloys.172 Most of these alloys are structurally unstable during creep because of such effects as recrystallization, overaging, and so forth, so that the results are of limited application. The only pure metals on which observations have been made appear to be lead3,4 and aluminum5 tested under conditions which allow rapid recovery to take place. The present work describes the effect of a single stress change on the creep and fracture properties of a metal in which recovery is very slow. A Ni 0.1 at. pct Pd alloy was used so that grain growth and recrystallization did not occur during creep testing. Specimens of this material were heat-treated to give a uniform grain size of 10 grains per mm. Creep tests were carried out at 500°C using Denison T.47 machines; details of the creep-testing procedure have been given elsewhere.' All specimens were tested at a constant initial stress of 5 tpsi which gives, in an uninterrupted test, a minimum creep rate of ~10-3 pct per rnin and a life of -7000 min. Specimens were loaded under these standard conditions and after 1500 min, when secondary creep was well-established, the stress was changed to either 8, 7, 6, 4, 2, or 0 tpsi for a period of 180 min. After this time the original load was reapplied and the tests continued to fracture. The results are shown in Fig. 1. No detectable creep occurred during the period of reduced load, even at 4 tpsi, and on reverting to 5 tpsi the creep rate returned to its original value immediately. Increasing the stress to 8, 7, or 6 tpsi resulted in an instantaneous extension followed by a period of transient creep leading to a new steady creep rate. On returning from these higher stresses, the resulting creep rate at 5 tpsi was very low compared with the original value. Furthermore, the higher the stress during the stress change, the lower was the final creep rate. It is significant that the rupture life is comparatively unaffected by any of these stress changes.

Jan 1, 1965

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

Phase II of President Nixon's economic game plan will incorporate many top flight metals mining companies. The large corporations must receive approval from the Cost of Living Council before increasing prices and or wages. The theory here is that, with large companies complying with advance approval, smaller firms will be examined more closely by government, and thus will be forced also to comply. Rep. Paul McCloskey (R.-Calif.) called for a moratorium on strip mining for "the few years involved before we adopt a national energy policy and a national land use policy." McCloskey, who is a cosponsor of Congressional legislation that would outlaw strip mining, told a hearing that a "moratorium can scarcely hurt us until national energy and land use policies are adopted."

Jan 1, 1971

By Andrew W. Jenike

STORAGE AND FLOW Introduction The layout and design of a bin or stockpile for bulk solids should assure reliable feed at the required time and rate without spillage and, when required, without segregation and degradation. The typical procedure in the design for gravity flow follows these steps: 1. The bulk solids to be stored are identified and the range of moisture content, temperature, feed rate and time of storage at rest, as well as the storage capacity, are specified. The materials of construction of the hopper, that is of the converging part of the bin, are decided upon. Hopper liners and coatings to reduce wall friction are considered. 2. The flow properties of the bulk solids and the friction angles against the wall materials are measured for the expected range of conditions. 3. The width of a slot outlet needed for reliable flow of each solid under the full range of conditions is determined from the tests. This dimension is an explicit measure of flowability of a solid. The widest slot determines the critical solid and the critical conditions. 4. A suitable feeder of size sufficient for the widest slot outlet is selected. 5. On the basis of the measured wall friction angles, a suitable wall material is selected and a mass flow hopper is designed to ensure reliable and uniform flow of solid into the feeder and to minimize the load on the feeder. The mass flow hopper may extend upward to the intersection with the cylinder thus producing a mass flow bin. Alternatively, the hopper may terminate at a height equal to a few widths of the outlet and then expand at a less steep slope in its upper part in order to save headroom, or it may terminate in the flat bottom of a bin or stockpile. The choice depends on the flow properties of the solids and the size of the bin or stockpile. 6. The design of the bin is completed for the specified storage capacity. Multiple hoppers and

Jan 1, 1982

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month's performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont's original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin's mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By Don Masson

MUCH has been written and many prophecies made on the subject of plastics as a replacement for metal, and the extent to which these materials will compete with each other for peace- time markets. (Metal is used in a broad sense to include all types.) But although certain synthetic resin materials have made considerable headway in war production, this change to plastics can hardly be regarded as a serious threat to the mining and metallurgical industries. Even today, the total yearly tonnage of plastic materials is approximately only 1 per cent of that of steel, and only a small fraction of this might be considered as actually replacing steel. However, these figures must not be taken as indicating that the importance of plastics in fields hitherto considered exclusively the territory of metals is negligible-far from it. Considering the comparatively minute tonnage of plastics now being produced in comparison to the output of metals, the number of applications where plastics have augmented or aided the sale of metals is considerable.

Jan 1, 1944

By Gary P. Thomason

INTRODUCTION One may have heard about how various projects were financed or certain companies were successful in obtaining a bank loan, but there are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of debt financing sources available to finance minerals operations (see the next Chapter 11), but these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to many minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. LOAN APPROVAL PROCESS The initial stages of the loan approval process should begin long before the bankers, and the organizations they represent, enter upon the scene. The loan approval can be broken down into six stages: 1) Generation 2) Preparation 3) Presentation 4) Evaluation 5) Approval 6) Documentation As you can see in Figure 1, the bank is only directly involved in the second half of the process. The perils in obtaining financing for the smaller minerals venture are primarily in the first three stages, not the last three. The minerals venture making application for a loan can, in almost every case, improve its chances of success by carefully planning and preparing itself and the information that will be required of it in the loan approval process. Generation This first step in the process is deciding on the need for a loan. (Earlier papers in this Book and in Chapter 11 provide some guidance.) It is surprising how many ventures confuse the need for money with the need for a loan. Suffice to say that the equity investor risks both the timing of the yield on his capital and, ultimately, his capital. The lender, on the other hand, advances temporary funds which he expects to be repaid on a specific schedule with a fixed

Jan 1, 1985

By A. E. Back, K. E. Tame, W. F. Wyman, S. F. Ravitz

IN 1940, when it appeared that the United States soon might be cut off from foreign sources of high-grade manganese ore, the Bureau of Mines began an extensive series of investigations on the production of ferrgrade products from low-grade domestic ores by ore-dressing, pyrometallurgical, and hydrometallurgical methods. Among the hydrometallurgical processes for oxide ores investigated was a sulphur dioxide process in which the manganese was recovered from solution by precipitation with lime;1 this process is essentially as follows: The ground ore is suspended in water and leached with SO2 gas to extract the manganese as manganese sulphate. Calcium chloride is then added to the slurry to precipitate calcium sulphate and form manganous chloride solution, and the resultant slurry is filtered to remove the calcium sulphate together with the in- soluble portion of the ore. Calcium hydroxide is added to the filtrate and the mixture is agitated with air to precipitate hydrated oxides of manganese and regenerate calcium chloride. The precipitate is calcined, and the calcium chloride is recycled. To determine manganese extraction, reagent consumption, grade of product, and similar data for this process, a laboratory investigation was started. Two minor modifications in the process were soon made: (I) the ore was suspended in calcium chloride solution instead of in water in order to extract the manganese and precipitate the calcium sulphate in one step, and (2) the agitation with air after the addition of slaked lime to the filtrate was omitted because manganese hydroxide is readily precipitated without air agitation and can be nodulized or sintered to a satisfactory product. When the process was carried through a series of cyclic tests, it was noted that the concentration of dithionate ion (which is one of the products of oxidation of SO2 by MnOz) in the cycled solution gradually increased; at the same time the chloride content of the solution gradually decreased, owing to soluble losses in the leach residue and in the precipitate. After a number of cycles, the calcium chloride became virtually completely replaced by calcium dithionate, the quantity of dithionate ion formed during the leach being more than enough to make up for the losses of dithionate in filtering. The calcium chloride process thus developed into a calcium dithionate process. Since the latter eliminated the need for make-up calcium chloride, and the dithionate solutions appeared much less corrosive than the chloride solutions, work on the calcium chloride process was dropped in favor of the calcium dithionate process. ACKNOWLEDGMENTS The dithionate process was developed by the Bureau of Mines as part of a

Jan 1, 1946

By G. W. Dopson, P. A. Korpi

The angular spiral lining system reduces energy consumption and grinding media consumption in grate discharge ball milk. This paper discusses the effect of this lining system on mill product size distribution. Performance comparison of a grinding circuit outfitted with angular spiral liners in ball mills are made with respect to standard double wave-liner installations. The angular spiral lining system was developed by Waagner-Biro of Austria. The installation of this lining system at Magma Copper Co. is the first of its kind in a grate discharge ball mill used for wet grinding.

Jan 1, 1983