Search Documents

By C. Y. Wen, H. O. Hofman

In casting a thermal balance of the heat generated and absorbed in a blast-furnace treating lead-, copper- and similar non-ferrous ores, assumptions have always to be made for the values of the heat of formation of slag. Considering that the larger part of the charge introduced into the furnace comes out in the form of slag, the significance becomes apparent of a lack of heat-values for the singulo-silicate, which is the type of slag commonly made. The aim of the present investigation is to supply these heat-values as far as possible with the apparatus and the time available. The heats of formation of the ferrous and manganous bi-silicates have been determined by Le Chatelier;1 those of some silicates other than iron and manganese by Tschernobaeff;' finally Richards3 gives a figure for a copper blast-furnace slag of known composition. The existing data and those resulting from the present investigation are assembled in Table VI. 11. Materials Used. The materials used in the experiments mere silica, ferrous oxide, and calcium carbonate. Silica.—The silica sold in the market as chemically pure usually contains small amounts of magnesia, lime, and alumina, and is therefore not suited for the work. The pure material was obtained from clear quartz crystals from Arkansas, broken in a diamond mortar and ground in an agate mortar to pass

Jan 1, 1911

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-'; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann's and Planck's constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By Clemens Catesby Jones

The substance of this paper, now amended and altered in form for its present use, was the basis of a private report prepared under professional engagement.* A private report is necessarily objective, and deprived of the scope and technicality of a scieintific treatise—which accounts for the prevalence of drawings and succinct mathematical statements rather than full descriptive details in a paper reproduced from data, of which all the original working-notes have been destroyed. In a practical sense the Hudson river valley clay-deposits owe their present existence to the protection afforded by the rock-formations on which they are supported, and, instead of being uniform in depth or continuity, are subject to the irregularities of the rugged masses which preceded and are now concealed by them. The only available information concerning these deposits contained in previous public reports or maps furnished at best a mere photograph of the surface, and as now apparent this was misleading or unreliable. It was the object of this investigation to determine in a practical manner the location, form and extent of all the clay-deposits at present existing in the lower Hudson river valley, and to ascertain with a

Jan 1, 1900

By Smith, George Otis

THE matter that I have on my mind this evening is engineering's need of an open forum. Our fathers of three centuries ago were pro-testanta for freedom of speech and thought in matters religious; later, our fathers were revolutionists for freedom of speech in matters political; until today freedom of speech has become so universal throughout the land that even in the sanctuary of our homes, at times, we have to turn off the loud-speaker. Talk is not always a condition of progress, but light is everywhere necessary to growth, whether the growing thing is a blade of grass, a baby chick, or a young idea, and we must regret anything that tends to shut out the light from the operations of business and industry. Of course, I realize there is little that is novel in what I am saying. Indeed, I have found that Dr. James Douglas-a name we love to honor in our Institute-as long ago as 1907, gave an address at the Toronto meeting that any of us would be proud to be author of twenty-one years after. Dr. Douglas at that time spoke on secrecy in the arts and the text then taken by this leader in metallurgical technique and in the constructive management of big business was "the dangerous temptation to adopt secretive methods by very large corporations." In both thought and language Dr. Douglas was direct and vigorous and he needs no internreter. He advocated the wide open door for ideas on two counts: advancement of technical knowledge and education of public opinion. A few sentences will serve not only to prove the vision of James Douglas, but also, I hope, tempt you to hunt up his address in the Institute's TRANSACTIONS, and thus get his whole thought first hand.

Jan 1, 1928

By F. W. Metzger

INTRODUCTION Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA, have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic units, or benches, within the coal seam can be made. These units are recognizable in the core and also on geophysical logs. Like any systematic approach, geologic modeling has been refined and improved through new technologies. Today, coal seam properties are mapped using computer applications. Rapid access and manipulation of these data allow for optimization of mining efforts. This presentation will demonstrate how a detailed mapping program can be important in both pre-mine development and in-pit quality control.

Jan 1, 1983

By T. Prof. Egleston

ALL industrial establishments whose operations depend upon chemical reactions use gases. In the simplest case the oxygen of the atmosphere, heated or not, as the case may be, is used, and in other cases, gases which are produced by a special apparatus of more or less complex composition. The manufacturer depends, for the success of his operations, entirely upon having these gases arrive at the right time, in the proper proportions, at the required temperature. It often requires but a slight variation in their composition to make a given process a success or a failure. In most cases the gas used is formed from fuel, and according as variations in its composition are produced by alterations in the manner of charging the grate, not only different, but often directly opposite, results are obtained. The great industrial question of the present time, and one upon which the prosperity of the world depends, is how to get the greatest amount of useful effect from fuel, whether the caloric is used directly or is transformed into horse-power. In almost all industrial pursuits this translates itself into the question of how to construct a fireplace and its adjuncts in such a way that the heat of the flame and of the products of combustion shall be made to produce a maximum effect. Unfortunately, until very recently, except by comparison, there was no means of ascertaining whether the loss of useful effect was 80, 40, or 20 per cent. of the total amount of fuel employed. It seems now strange that there should have been furnaces so constructed as to produce 20 per cent. of carbonic acid in the fireplace, but this has been proved by analysis to have been true. It does seem incredible that, notwithstanding the immense number and variety of furnaces used for different processes, and the great difference in kind, quality, and quantity of fuels consumed, there should formerly have been used for them all, the same stereotyped fireplace, varied only in its dimensions of height, length, and breadth. It is true that, with a good fireman, excellent effects may be, and have been, produced, but the manufacture is here, as in many other cases, dependent on the intelligence of the workman, a very uncertain reliance for capital to rest upon. The workman, unless he receives a prime for fuel saved, or is fined for excessive use of it, may be said

Jan 1, 1874

R. F. MCELVENNY.- Over 20 years ago I went back East on a little tour of copper companies to see how copper was handled and fabricated, and I met a Mr. Bassett who took me through the Waterbury branche of the American Brass Co. I have not seen this gentleman for 20 years, but I have a letter from him that I would like to read to you. 'The American Brass Co. Waterbury, Conn. May 19, 1930. To the-Salt Lake City Conference on Reverberatory Smelting Practice: Through the courtesy of Mr. Scott Turner, Director of the U. S. Bureau of Mines, Mr. G. L. Oldright has been temporarily released from his regular duties to act as your secretary. We have asked him and Mr. McElvenny to make the necessary preliminary arrangements and to present to you at the opening session the greetings of the officers and' directors of the Institute. I am very glad that it has been possible for you to come together under the auspices of the Institute and that the acceptance of our invitation has been so very unanimous. Such an acceptance of the invitation to this meeting indicates your interest in getting together for an exchange of technical data and ideas. We anticipate that this meeting will be of real service to the smelting industry through your open discussion and exchange of ideas, and we sincerely hope that you will form an organization which will arrange for future meetings of a similar nature. While it probably may not be desirable to. distribute the minutes of this conference except to the members who take part in it, we hope that later the Institute publications may be enriched by such matter as you think it desirable to have published; and also, that some of you may be able to offer technical papers for the Institute publications. I hope that you will find a permanent organization desirable and trust that it will be possible for you to form such an organization so that conferences may be regularly called. We hope that you can make use of the Institute organization and that we can be of real service to your industry. With best wishes for your success in this undertaking, I am Most cordially yours, W. H. Bassett, President.

Jan 1, 1930

By J. D. Vincent, Pierre R. Hines

INTRODUCTION OF FROTH FLOTATION INTO THE UNITED STATES "The introduction and development of the flotation process have proved to be of such momentous importance to the mining industry of the United States that they deserve to be considered historically ." T. A. Rickard l James M. Hyde installed the first froth flotation process in the U. S., about Aug. 1, 1911, at the Basin Reduction Co. plant, Basin, Mont., which was then under lease to the Butte and Superior Copper Co.2 Two months later, the Minerals Separation Ltd.. filed suit in the U. S. District Court of Montana against Mr. Hyde char& him with infringement of their Patent 835, 120/1906. The U. S. District Court decided in favor of Minerals Separation Ltd. on July 28, 1913. This decision was reversed by the Ninth Court of Appeals in San Francisco on May 4, 1914. Then the U. S. Supreme Court, on Dec. 11, 1916, upheld the patent on three counts only but restricted it to 'the use of less than one percent of oil.” The Miami Copper Co. was sued by Minerals Separation on Oct. 10, 1914, for infringement of Patents 835,120 and 962,678, and 1,099,699. The Miami Copper Co. was operating under John M. Callow's froth flotation process Patent 1,104,755/~uly 23, 1914. Miami lost this suit in the District Court of Wilmington, Del., and appealed to the Court of Appeals, Third Circuit, Philadelphia. The Third Court of Appeals decided against Miami, May 24, 1917. The case was referred to a Master and hearings to determine profit and damages were not settled until 1923. Nevada Consolidated Copper Co. was sued Sept. 9, 1919, and Magma Copper Co. was sued Jan. 10, 1920. Thus, the first ten years of froth flotation in the U. S. were beset by patent litigation. This litigation suppressed the free circulation of new discoveries or useful information that might be cited in a patent suit against the originator; it accounts for many of the blank spaces in the historical record. T. A. Rickard3 has reviewed the history of flotation and has given the chain of discoveries, patents, and processes that resulted in froth flotation. He has re- ported also on the patent litigation beginning in 1911 and ending in November 1923, when Minerals Separation's Patent 835,120 expired. He comments on

Jan 1, 1962

By T. Prof. Egleston

DURING the last winter we have been actively engaged in the School of Mines in search for boracic acid. This has been owing to the fact that Mr. M. W. Iles, assistant in the qualitative laboratory, has discovered a test for that substance which makes its discovery exceedingly simple instead of being, as previously, very difficult. It consists in powdering the mineral, calcining it, then moistening it with sulphuric acid, and heating on a platinum wire until the sulphuric acid is expelled. It is then moistened with glycerin and made to take fire. If boracic acid is present it infallibly gives a green flame. It is not at all surprising, under such circumstances, the test being so easy, that boracic acid has been found by the students in a great many cases where its presence was not previously suspected, and in some where its detection was previously too difficult to warrant looking for it. We were not prepared, however, for its discovery in Lake Superior iron ores, and were disposed at first to think that a mistake had been made. After, however, it had been frequently reported in these ores it was considered worth while

Jan 1, 1877

By J. B. Shannon, J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc. and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the `New Missouri Lead Belt'. Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated 1100 ft below the surface at an elevation 270 ft above sea level, the flat lying sinuous orebodies are up to 250 ft wide, 85 ft high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite.

Jan 7, 1973

By Henry J. Sandri

The use of economic models for forecasting purposes is an inexact yet necessary tool for mineral decision making. One method not commonly used is cyclical analysis because of its "non-scientific approach". However, under certain circumstances a modified cyclical approach can provide useful insight to mining companies. The current paper discusses mineral modeling, the type of economic models and the use of cyclical forecasting for mining firms (not speculators) involved in precious metals.

Jan 1, 1984

By M. Gell, G. R. Leveran

The high- and low-cycle fatigue properties of the nickel-base superalloy, Mar-MBOO, in columnar-grained and single-crystal forms were determined at room temperature. It was found that the fatigue lives of these materials were greatly affected by the size of preexisting cracks in MC-type carbides contained in the micro structure. Most of the data falls on two curves given by: (zN)'/A€= K, where Nf is the number of cycles to failure, Af is the total strain range, and K is a function of carbide size. No difference was observed in the fatigue behavior of the columnar-grained and single-crystal materials for the same MC carbide size. Matrix slip and crack initiation occurred at precracked MC carbides and, to a lesser extent, at micropores. Fatigue crack propagation was mainly in the Stage I mode, i.e., on cry stallo graPhic slip planes. The Stage I fracture in these materials was unusual in that distinct features were observed on the fracture surfaces. In high-cycle fatigue, these features resembled those commonly observed on the cleavage fracture surfaces of bcc and hcp materials. Yet, in this study, the cracks propagated slowly in a cyclic manner. In low-cycle fatigue, the Stage I facets contained equiaxed dimples, similar to those observed on the tensile fracture surfaces of ductile materials. These observations indicate that both local normal and shear stresses are involved in these Stage I fractures. A model is proposed to explain these results based on the weakening of the cohesive energy of the active slip planes by reversed shear deformation and the fracture of the bonds across the weakened planes by the local normal stress. RECENT developments in casting technology have produced cast nickel-base superalloys in columnar -grained and single-crystal forms.1'2 The tensile and creep properties of the nickel-base superalloy, Mar-M200, cast in these forms have been shown to be superior to the corresponding properties of the conventionally cast polycrystalline material.lp2 This improvement in properties results, in part, from the elimination of grain boundaries in the single crystals and the alignment of the grain boundaries parallel to the stress axis in the columnar-grained castings. As part of a program to evaluate the fatigue properties of nickel-base superalloys cast in single-crystal and columnar-grained forms, a study has been made of the cyclic deformation and fracture of Mar-M2OO at room temperature. M. fiFl I .hininr Mpmher AIMF ic ^pninr Rocoarrh Accn^iata anH I) EXPERIMENTAL PROCEDURE The composition range of Mar-Ma00 in weight percent is: 8 to 10 Cr, 9 to 11 Co, 11.5 to 13.5 W, 0.75 to 1.25 Cb, 1.75 to 2.25 Ti, 4.75 to 5.25 Al, 0.01 to 0.02 B, 0.03 to 0.08 Zr, 0.07 to 0.12 C, bal. Ni. All of the castings met the above specifications. The castings were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr which resulted in a 0.2 pct offset yield stress of 150,000 psi at room temperature. The microstructure of the material consisted of cuboidal, coherent particles of ordered, fcc Ni3(A1,Ti) (commonly designated y'), approximately 0.3 p on edge, distributed in an fcc y solid-solution matrix. MC carbides together with shrinkage and gas micropores were also distributed throughout the materials. The MC carbides and micropores were located preferentially in the interdendritic interstices, as well as in the grain boundaries in the columnar-grained castings. The (100) direction of all the single crystals and the common (100) axis of the grains in the columnar materials were aligned within about 5 deg of the specimen axis. Fatigue testing was carried out in the high-cycle (HCF) and low-cycle (LCF) fatigue regions, with the major difference being gross yielding of the specimen occurred during the first cycle in the LCF region. This division also corresponded with the more usual one in which the life of a specimen in LCF is less than lo4 cycles and that in HCF is greater than lo4 cycles. The designs of the high-cycle fatigue and low-cycle fatigue specimens are shown in Figs. l(a) and (c), respectively. The gage sections of both HCF and LCF specimens were electropolished prior to testing. The HCF specimens were tested in an MTS, closed-loop, hydraulic fatigue machine at 10 cps in air. The specimens were cycled between a tensile stress of 5000 psi and a maximum tensile stress which ranged from 35,000 to 125,000 psi, Fig. l(b). The LCF specimens were cycled under strain control from zero to a maximum tensile strain, Fig. l(d), in a Wiedemann-Baldwin testing machine. The experimental procedure has been described elsewhere.3'4 Both HCF and LCF tests were interrupted periodically in order to replicate the development of slip and cracking at the specimen surface. This was accomplished by placing plastic replicating tape around the gage section of the specimen while the specimen was in the mahine. The size of the MC carbides for all specimens was measured on a polished longitudinal section through the gage section after fatigue testing. The method of measurement consisted of carefully scanning the entire polished section in order to locate the largest MC carbides. Photographs were then taken of the six longest carbides oriented approximately normal to the

Jan 1, 1969

By John V. Beall

Many Americans will judge the energy crisis by the picture shrink on their TV screen. And they are right to make this assessment considering the large areas of the country with marginal generating capacity, (See Fig, 1). The Federal Power Commission (FPC) recommends 20-25% reserve generating capacity above peak summer loads and 15-20% as minimal. The New York metropolitan area is the most concentrated power service area in the United States, and a spot check with Consolidated Edison, serving this area, revealed that on Friday, August 18, the company was operating at 5% reserve.

Jan 10, 1972

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract.

Jan 1, 1928

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947

By T. Egleston

THE manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their construction, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be equally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seem to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest quantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can be made in kilns, but that most of the workmen do not like kiln charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a large production of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the quantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not equally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron * Read at the Pittsburgh meeting, May, 1879.

Jan 1, 1880

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles', this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construc-tion. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and, drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By Axel Hultgren

IN ingots of silicon-killed carbon steel made without addition of - aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially. In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents arid, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,10,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis17 and their amount to increase from the top downward in the axial region .2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form," by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.15 Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19,20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping' or of refractory material from various sources1,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistance to hydrofluoric acid, imparted by the alumina content. Silicate inclusions, are often referred to as. the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1948