Search Documents

By E. C. Tveter, R. B. Tippin

The separation of minerals by heavy liquids is a standard laboratory technique which goes back at least 50 years, but commercially economic application of this principal to ore concenfration has been prevented by problems of liquid recovery. Recent investigations which demonstrate the different types of liquid-solid systems on various ores using the two major heavy liquids - methylene bromide and tetra-bromoelhane — are discussed in this article. As a result of these studies, over-all liquid recovery, and especially desorption of heavy liquid from the mineral surface, was improved by the use of surfactants as well as both thermal and mechanical energy. The examples given in the article indicate that heavy liquids which should find major commercial use in ore concentration are now available. The sink-float process using a heavy liquid medium has long been recognized as a nearly perfect method of mineral separation based on the differences in density of the minerals. The use of heavy liquid separation (HLS) offers the potential of an ore dressing method that provides the maximum possible natural concentrate grade and high recovery. In addi- tion the process requires no water, causes no waste disposal problems, and is extremely simple — the crushed ore is merely introduced into a liquid whose density is between that of the minerals to be separated. The minerals lighter than the liquid float while those heavier than the liquid sink. As such, HLS has become a standard laboratory tool but major commercial application has been prevented by the requirement for complete recovery of the heavy liquid, imposed by economics and materials handling hazards. Investigations, both in the United States and abroad, have shown that improved liquid stability as well as improved chemical engineering techniques brighten the future for HLS in ore dressing. The available commercial heavy liquids suitable for mineral separation cost from $2.00 to $20.00 per gallon1 and on this basis alone their complete recovery is economically desirable. Possibly of even greater importance is the fact that any residual heavy liquid remaining on the products could create a serious toxicity hazard. Consequently, to make the process commercially attractive requires (1) essentially complete removal of the liquid from the ore products and (2) optimum recovery of the liquid for reuse. Until recently these two stipulations have remained as obstacles but laboratory and pilot plant research now in progress suggests that these may soon be overcome. Various heavy liquid recovery systems have been proposed to meet these requirements and might be classified into one or more of the following three general classes: Solvent Wash (Fig. 1): The dissolution of the heavy liquid from the ore with a less expensive solvent,

Jan 1, 1969

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By Robert L. Dean, Michael Hoch, Samuel M. Wolosin, Chung K. Hwu

The general shape of the 1450°C isotherm of the Ti-TiO-ZrO2-Zr region was evaluated from the surrounding binary phase diagrams and from thermo-dynamic data on the metal-oxygen binaries. The phase boundaries were accurately determined using X-ray and metallographic techniques. At 1450°C the system shows a large bcc ß field, which extends from the two metal-oxygen binary systems as a Gaussian error function, and is stable up to 30 at. pct 0 when Ti and Zr are present in equal amounts. At higher O Concentrations, the ß field is in equilibrium with t-ZrO . The following four regions, with three solid phases, are present: two a ß t-ZrO,, a TW t-ZrO,, and TiO t-ZrO2 c-ZrO2. On cooling the ß phase transforms into the a phase, going through the w transition phase. The isotherm at 1500°C for the region TiO-TiO,-ZrO, was obtained by using X-ray diffraction. At 1500°C a large c-ZrOz region is present as well as a large two-phase field, Ti0 c-ZrO,. The following regions, with three solid phases in equilibrium, were found These regions are relatively small. The solidus and liquidus relationships were determined by observing samples suspended in a tungsten crucible by means of a fine tungsten wire and heated in vacuum. Eleven univariant points were found. C-ZrO, decomposes through a peritectic reaction into liquid t-ZrO2. The activities of Ti and TiO in the TiO t-ZrOz and in the two a ß t-ZrO regions were measured using the Knudsen effusion method. In the a TiO t-ZrO, region the activities of Ti and Ti are the same, as in the a — Ti TiO binary. In the two a t-ZrO, regions, the Ti activity is high and the Ti0 activity very low, although all phases present contain at least 30 at. pct 0. This indicates a short-range order in the solid phases, Zr atoms being preferentially surrounded by 0. 1 HE system Ti-Zr-0 is of interest because of the wide ranges of solid solubility exhibited by the boundary systems; as titanium and zirconium both belong to the same group of the periodic table, large single-phase regions should occur within the system, with a great variation of properties (as the composition changes within the single-phase region). Furthermore, the possibility of modifying ZrO, to make it a more usable refractory by the addition of other metals makes this system also of interest. Because of the high affinity of titanium and zirconium for oxygen, the oxygen partial pressure is very low at all compositions; thus, there exists a ternary metal-metal-oxygen system in which the oxygen pressure is not an important variable, so long as it is low enough. When a sample is heated in vacuum to a temperature high enough for vaporization to occur, the vapor phase will consist of metal and metal-oxide gas, the oxygen concentration being very low. The phase relationships in the surrounding binary systems have already been reported in the literature; therefore, the study of the ternary diagram

Jan 1, 1962

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role ad the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By Carl Beal

THE most important factors that should be given consideration in valuation of oil land are: (1) the amount of oil the property will produce; (2) the amount of money this oil will bring (based upon the future prices of oil) ; (3) development and production costs; (4) the rate of interest on the investment; (5) the retirement or amortization of invested capital; and (6) the salvage or "scrap" value of the equipment when the property is exhausted. These factors are of varying importance, and some of them may not enter all valuation problems, but most of them should be given consideration in any valuation even though only a rough estimate of the value of the property is desired. The value of a property may be changed over-night by the completion of important test wells, by the sudden water flooding, or by a change in the price of oil. The best a petroleum engineer can give is the value of the property under the conditions existing at the time the appraisal is made with a fair forecast of future action of the wells and of the price of oil. Our experience in the scientific valuation of oil lands is not broad and there is very little published information on the subject; it, therefore, becomes necessary in studying such problems to form comparisons with the factors involved in the valuation of mines-the closest parallel. One of the reasons for the lack of substantial progress in oil-land valuation methods has been the necessity of making an estimate of the future production of the oil property to be valued. Oil men and accountants have not generally conceded that such estimates could be made with any degree of accuracy. It has been shown, however, in several recent publications that with certain data available reasonably close estimates can be made. The accuracy of an appraisal depends chiefly on the accuracy of the estimates of future production and of the future price of oil. The accuracy of the former is sometimes necessarily based on geological inferences. Geology is not an exact science and geological data in connection with oil production cannot always be mathematically evaluated.

Jan 9, 1919

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

By S. H. Chauvenet

The binding of the boshes and inwalls of blast furnaces has always been an expensive piece of work. When the old stone stack was replaced by the iron shell, the brickwork was kept at a thickness of five feet or more. These five-foot walls were still too thick, and the practice now is to have as thin walls as possible and to have a free circulation of air about the brickwork of the furnace. The " basket," or lattice-work biuding, accomplishes this object, but it is expensive, m to first cost, and, if any change in the diameter of a furnace has to be made, it necessitates an alteration of the binding or of the thickness of the walls.

Jan 1, 1882

By Joseph D. Weeks

NOTE BY THE SECRETARY.—This address having been made the object of much hostile comment, arising, as Mr. Weeks believed, in large part from misunderstanding of its purpose and meaning, was, by his express direction, withheld from official publication in the Transactions until he should have so modified or added to it as to make such misunderstanding impossible. His illness and death prevented him from executing this intention; and, consequently, the only version of the address now in the Secretary&apos;s hands is one of which the author had forbidden the publication. Under the circumstances, therefore, it seems best to publish, in this place, only some portions of the address and its appendixes which have a historical value and are beyond controversy, giving at the same time a summary of its general nature, based upon the original manuscript and upon correspondence with Mr. Weeks. For this summary, the Secretary is alone responsible. The address was essentially a restatement of well-known and established facts, which it interpreted as proving that, of the three elements of the Bessemer process (namely, the pneumatic principle, the successful mechanical application of that principle, and the recarburization with spiegeleisen), William Kelly was the first inventor of the first, Bessemer of the second, and Mushet of the third. Mr. Weeks used the words " original inventor " in the sense (as he explained in one place) of first inventor, and neither asserted nor believed that Bessemer&apos;s con-

Jan 1, 1897

By W. Mostowitsch

Lead sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. 11. Decomposition of PbS04 by Heat The dissociation of PbSO4 into PbO and SO3 or SO2 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumannl found that PbS04 was not affected-by heat at 800" C.; that dissociation began at 900" C., and was rapid at 1,000° when the salt lost in 1 1/2 hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbS04 begins at 195&apos; C., but progresses very slowly, with the formation of the basic salt 6PbO.5SO3 at 705"; that this salt undergoes a transformation at 847") begins to be decomposed at 888") to sinter at 896", and to fuse at 910"; rapid dissociation begins at 952") and is accompanied by volatilization of PbO; retardations at 958" and 962" indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900" C. in 30 min. only 0.63 per cent. of its 803, and that the loss increased with

Jan 1, 1917

By B. Chalmers

THE practical importance of the phenomena of melting and freezing must have been recognized for a very long time. The difference between ice and water, for example, has had a profound influence on the history of mankind and the evolution of society. The possibility of melting a metal and allowing it to freeze in a mold of chosen shape has been an essential ingredient in our mastery of the art of shaping metals, and therefore in the evolution of the: machine age in which we find ourselves. The importance of melting and freezing, as applied to metals and alloys, has been so great, in fact, that empirical solutions have been found for the multitude of practical problems that have arisen. This approach has been so successful that relatively little attention has been directed to arriving at an understanding of the fundamentals of the processes. But metallurgy has come to a stage at which we may expect that some, at least, of the more complex problems that have not yet been solved (or perhaps even recognized) may be handled more effectively by scientific study, theoretical understanding, and logical experimentation than by trial and error. In this lecture, therefore, I propose to describe in outline what I think really happens when a metal freezes. In doing so I hope to explain many of the phenomena which have been observed, and in particular to account for the structures that are obtained in actual ingots and castings. The basic problem, to which this lecture represents a tentative partial answer, is this: a mass of metal, containing known proportions of various elements, is melted, heated to a given temperature, and then allowed to freeze under specified conditions. What will be the "structure" of the resulting metal? The term structure includes: 1—crystal size, shape, and orientations, 2—distribution of chemical elements, and 3-—shape, including cracks, cavities, pores, etc. The Solid-Liquid Interface We will first consider what takes place if a single crystal of a metal in the form of a rod is heated, not uniformly, but so that one end is hotter than the other. If this heating process is continued long enough, the hotter end will eventually melt; we will suppose that the rod is in a containing vessel so that the molten metal does not run away, Fig. 1. When some of the metal has melted, we have some solid, some liquid, and an interface or surface of contact between them. If the source of heat is now removed, the interface will move so that some of the liquid freezes, and if the supply of heat is suitably adjusted the interface will remain at rest. This very simple arrangement allows us to study the basic processes of melting and freezing, and if we fully understand this simple case, we may be able to account for what takes place under practical conditions where the heat does not all flow in the same direction, and where the heat flow is determined not by a controllable source of heat but by the heat capacity and temperature of metal and mold, and by the heat loss from the mold surface. The solid-liquid interface is evidently the region of the greatest interest to us; on one side of it there is crystalline solid, and on the other, liquid. In the solid, each atom has a well defined position, around which it vibrates as a result of thermal agitation. It only leaves this position in the relatively rare event of a "diffusion jump." The liquid is much less systematically organized. The atoms are about as far from their neighbors as in the solid, but the arrangement is much less systematic and is continuously changing. The solid and the liquid are represented diagrammatically in Fig. 2. The average energy of the atoms in the liquid is greater than in the solid by an amount that corresponds to the latent heat of fusion, i.e., the amount of heat that has to be supplied to convert unit mass of solid into liquid at the same temperature. The Two Processes As has recently been shown by Jackson and Chalmers,3 many of the features of the processes of freezing and melting can be understood if it is assumed that a continuous and rapid interchange of atoms between solid and liquid always takes place at a solid-liquid interface." It is necessary to con- sider two distinct processes, that of melting, in which atoms leave the surface of the solid and become part of the liquid, and the converse process,

Jan 1, 1955

CONTENTS PAGE Need for Research in Foundry Pig Iron. By Richard Moldenke. (With Discussion) 1 Carbon Characteristics of Copper-bearing Pig Iron. By W. B. Coleman. (With Discussion) 12 A Pig Iron, Low in Total Carbon, is in Demand for Use in Various Industries. By Enrique Touceda. (With Discussion) 24 Carbon in Pig Iron. By Ralph H. Sweetser. (With Discussion) 28 Second Session (Discussion) 37 Need for Research in Foundry Pig Iron BY RICHARD MOLDENKE,* WATCHUNG, N. J. So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and, for the

Jan 1, 1927

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO&apos;AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor&apos; and Kay and alor&apos; determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.&apos; , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O&apos;Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

Frank L. Bader has been appointed to the sales staff of Lehigh Navigation Coal Co. in the Philadelphia territory. H. C. Burrell, former coordinator of raw materials, Pittsburgh, Penna., has been made manager of raw materials for Columbia-Geneva Div. of U. S. Steel Co., San Francisco. J. H. Cazier has resigned as general superintendent of Bagdad Copper Corp., Bagdad, Ariz., to devote full time with E. A. Scholz to the operation of the Copper King, Phillips and Black Pearl Mines near Bagdad. They have operated the Copper King zinc mine for more than two years.. Production started from the Black Pearl and Phillips tungsten mines during the past year. Robert T. Chapman has resigned from Reynolds Mining Corp. to join Westmoreland Manganese Corp. as general superintendent. Annan Cook, with Kennecott Copper Corp.&apos;s exploration dept. for the past three years, has been appointed district geologist for the eastern states.

Jan 1, 1952

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent, of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART I.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent., of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results.

Jan 1, 1929

[A Aalseth, Earl P. (M 51) Geol, Amerada Petr. Corp., Box 1498, Billings, Mont. Abadie, Henry G. (M 43) Asst to Supvr of Oper, Long Beach Oil Dev. Co., 255 S. Santa Clara, Long Beach 7, Calif. Abbe, T. Waldo (A 56) Ass&apos;t Dist Oper Supt, Sun Oil Co., Beaumont, Tex. Abbott, J. L. (M 56) Partner, Pritchard & Abbott, 501, Century Bldg, Fort Worth, Tex. Abbott, Richard H. (J 51) Owner, Abbott & Howard, 422 W. Hermosa, San Antonio, Tex. Abbott, Seth J., Jr. (M 51) Tekoil Corp., .2;A6 Mercantile Nat&apos;l. Bank. Dallas, Tex. Abbott,. William G. (M 50) Div Mgr, Rice Eng. & Op. Inc., Box 1142, Hobbs, N. M. Abderhalden, R. R. (J,59) Box 100, Carmi, Ill. Abel, Malcolm D., Gen Mgr, Bakke Oil Co., Midland, Tex. Abel, Raymond L. (M 28) Prof of Chem Engr, Univ. of Pittsburgh, Pittsburgh 13, Pa. Abel, Wayne K. (M 57) 1513 Patton Drive, Odessa, Tex.]

Jan 1, 1961

By C. F. Floe, N. J. Grant, A. Joukainen

A CCORDING to Guertler,¹ Smith and Hamilton were the first to study the Cu-Ti alloy system, but because of the presence of large amounts of impurities their data are inconclusive. Hensel and Larsen² in 1930 and Kroll³ in 1931 determined the high copper end of the diagram. In 1939 Laves and Wallbaum,4 in a short summary of compound determinations in titanium binary alloys, mentioned the existence of a face-centered cubic compound, Ti2Cu, with 96 atoms per unit cell, and also a compound, TiCu3, which was said to have a deformed hexagonal close-packed structure in which ordering had been observed. The existence of a compound, TiCu, was also found but the crystal structure was not determined. Craighead, Simmons, and Eastwood determined the effect of copper on the allotropic transformation in titanium. The investigation was limited to alloys containing from 0 to 5 pct Cu, using titanium of fairly high impurity content. Experimental Procedure The methods used for determination of the diagram included metallographic examination and X-ray and thermal analyses. The system was first worked out using the higher purity "Process A" sponge titanium and oxygen-free copper. The high titanium region was next determined more accurately using iodide titanium and vacuum-melted, oxygen-free copper. Preparation of Alloys: The alloys were prepared by arc melting under prepurified helium atmos- pheres in water-cooled copper crucibles. The high purity iodide titanium alloys were prepared by melting three compositions along with a specimen of unalloyed titanium in a single charge. A multiple crucible was used which consisted of a copper plate with four cup-like depressions. The unalloyed titanium was melted first and acted as a getter for any oxygen and nitrogen in the melting chamber. Since these elements harden titanium, the hardness of the standard specimen was an index of the highest probable contamination of the alloy melts. The sponge titanium alloy melts weighed from 100 to 200 g each and the iodide titanium melts from 20 to 25 g. In order to insure greater homogeneity most of the alloys were melted, turned, and remelted twice. The larger buttons made from sponge titanium were sectioned or crushed before remelting. These alloys up to 30 pct Cu were further homogenized by forging at 925°C. They forged readily up to 20 pct Cu but numerous cracks were formed in the alloys containing from 20 to 30 pct. Above 30 pct Cu the sponge titanium alloys were homogenized by heating for 200 hr at 850°C under prepurified helium. Similarly, the iodide-grade titanium alloys containing up to 3 pct Cu were homogenized at 1000°C for 24 hr and all others at 880°C for 200 hr.

Jan 1, 1953

By H. F. Miller

Fox some years the prejudice against basic open-hearth steel for casting has been gradually decreasing. Yet many consumers and engineers still cling to acid steel for castings, because of their alleged greater freedom from blow-holes and sponginess. Acid steel has been used for this purpose much longer than basic steel; and the melters in acid practice had it well in hand when basic steel was first tried. Then the necessity of learning a new set of laws for the production of satisfactory basic open-hearth steel for castings became evident. The first of these laws, in my opinion, has to do with the furnace construction. The heat should be melted down as speedily as possible so as to prevent excessive oxidation. I have described in another article &apos; some furnaces designed by me, and having as one of their features the promotion of quick melting. Size of the Furnace. The hearth of the furnace, however, is a decisive factor in the production of solid castings. The manufacturer should know the size of the heats he intends to make constantly, and should have his furnace built for that size of heat. The hearth should differ in dimensions from that of a furnace making ingotr steel. That is, the bath should be deeper and should have less surface-area. A shallow bath permits the slag to come out soon after the steel commences to flow, and thus prevents the additions from going into the steel, or from becoming uniformly distributed in case they have been put in hurriedly. Under this head comes the very poor practice of making small heats in hearths of a much larger capacity. If into a 25-or 30-ton furnace only 12 or 15 tons of metal is charged per heat, the proportion of heats that will be wild, or show signs

Jan 1, 1913

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. However, with the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, presently exploited by Foote Mineral Co., and the Great Salt Lake of Utah, to be exploited by the Great Salt Lake Chemicals Corp., have been defined as major sources of lithium. Also a lithium-bearing brine has been discovered in Chile. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close down their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938. Its ionic radius is 0.60A and its charge is + 1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO)/Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns. 1955). Genetically, the pegmatites are associated kith neigh- boring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their respective distance from the granitic bodies to which they are genetically related (Mulligan, 1965). Lithium is also found in small proportions in a variety of rocks. The average lithium

Jan 1, 1975

By V. Patarini, M. Salkind

BECAUSE of its high strength and stiffness coupled with low density, continuous boron filament is showing great promise as a potential reinforcement for both metals and nonmetals. Of primary consideration for structural applications is the fatigue behavior of boron fiber composites. Composite fatigue behavior is dependent upon three factors: 1) fiber fatigue behavior, 2) matrix fatigue behavior, and 3) the effect of the interface and fiber ends. The purpose of this note is to describe the behavior of boron filament in rotating beam fatigue. The filament, described by Talley&apos; and Galasso, Salkind, Kuehl, and Patarini,&apos; was made by the hydrogen reduction of boron trichloride on a hot tungsten filament. Testing was performed using a commercial rotating beam wire fatigue tester* described by Votta.~ One end of the test sample is held in a chuck in a synchronous motor. The sample is bent around in a "U" shape, and the other end inserted into a carbide bushing. The maximum strain occurs at the bottom of the "U" where the radius of curvature is a minimum. The strain is adjusted by adjusting the length of the specimen and the location of the bushing. Samples were rotated at 3600 rpm and an automatic shutoff device used to determine the number of cycles to failure. The measurements were accurate to the nearest 360 cycles. The fatigue behavior is summarized in Fig. 1 for fifty-one samples of 4.8 x 10"3 in. diam fibers and ten samples of 3.2 X 10"3 in. diam fiber. The two sample groups represent two different filament production runs and two different nominal size groups. Both groups exhibited nominal tensile strengths of 400,000 psi. No significant difference in the fatigue behavior of the two sample groups is apparent. The scatter in the data is not unexpected for a brittle filament which exhibits a tensile strength distribution with a standard deviation of 10 to 15 pct. Because the test procedure provides a known outer fiber strain in the sample, the maximum stress was calculated assuming a Young&apos;s modulus of 58 x 10&apos; psi. This value was selected as being representative of several nominal fiber sizes.2 All of the samples which failed exhibited sudden, catastrophic fracture, and no permanent deformation. One sample was stopped after 1.66 x lo8 cycles at *200,000 psi. The fiber exhibited no apparent damage or deformation. It is apparent that the fatigue resistance of boron filament is quite good. It can therefore be speculated that the fatigue behavior of boron fiber composites would be controlled by the "weaker links", namely matrix fatigue resistance and interface behavior. In fact, preliminary investigations have revealed that this is true for boron-reinforced aluminum? It should be noted that the data presented herein may not necessarily reflect the tensile fatigue behavior of boron filament. It is well-known that boron filament has a radial residual stress pattern with the outer surface in ~om~ression.~ Because of this fact, tensile failure is normally nucleated in the interior of the filament.5 Since the data presented herein is for a rotating beam test in which only the outer surface of the fiber is stressed to the maximum value, it would be incorrect to assume that the failure mechanism and fatigue behavior would be the same if the fiber were tested in tensile fatigue. The fact that many of the data are well above the nominal 400,000 psi tensile strength would tend to support this argument. The authors would like to express their appreciation to the United Aircraft Research Laboratories for supporting this investigation and for permission to publish the results. A portion of this effort was supported by the Air Force Materials Laboratory under contract AF33(615)-2125.

Jan 1, 1968