Search Documents

By S. E. Bretherton

MOST metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other metals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthless. Such was the experience of the oldest mines in Leadville, Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered y smelting the cinder or clinker left in the re-

Jan 7, 1914

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By Oscar Lee

RESERVE Mining Co., owned jointly, by Armco Steel Corp. and Republic Steel Corp., controls 9% miles of magnetic taconite ore on the eastern end of the Mesabi Range lying between Mesaba and Birch Lake. The ore reserve which can be mined by open pit methods is conservatively estimated at 1.5 billion tons under a shallow, loose overburden requiring no rock stripping. Taconite now being mined is in the upper cherty horizon. It has been metamorphosed by the intrusion of gabbro and most of the iron oxide is altered to magnetite. The nonmagnetic portion of the iron is practically all in the form of silicate. The magnetic iron is finely disseminated through the rock and requires grinding -150 mesh for clean liberation of the iron oxide from the gangue.

Jan 5, 1954

By George C. Branner

BAUXITE is produced in Arkansas from two mining districts in the central portion of the State. These are (1) the Fourche Mountain district, immediately south and southeast of Little Rock in Pulaski County, and (2) the Bauxite (town) district, about five miles east of Becton in the eastern part of Saline County. These two mining districts are about twelve miles apart, separated by territory which, so far, has produced a negligible amount of commercial ore. Mining was by open-pit methods exclusively until 1924, when underground methods came into use. From 1924 to 1930 about 40 per cent of all of the ore produced in Arkansas was mined by underground methods, mainly by retreating caving.

Jan 1, 1935

By Lo-Ching Chang, K. M. Goldman

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By K. M. Goldman, Lo-Ching Chang

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926

By H. P. Greenwald

THOSE interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. Amer-ican findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the pro-motion of mine safety.

Jan 1, 1938

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By William C. Sleppy

The nmgnetic susceptibility of heat-treatable aluminuin alloys is sensitive to chanyes such as solution or dissolution of solute and the precipitation of mew phases. By measuring the change in the magnetic susceptibility of aluminum alloys caused by various heat treatments, an empirical relation was found from which atomic arrangements in dilute binary alloys of copper, zinc, and magnesiutn in aluminum have been delineated. The relation predicts the ultimate formation of C1LA12 when copper is precipitated from solid solution in aluminum. Euidexce joy silovt- range order is found for copper in solid solution in aluminum in the sense that copper atoms avoid being nearest neighbors to an extent greater than would result from a purely random arrangertzeizt. Hume-Rothery has predicted such short-range order joy solid solution of copper in aluminum The Al-Zn system agrees with evidence obtained from X-ray scattering at small angles and predicts a tendency for zinc atoms to cluster in solid solution in aluminum. In the Al-mg system, the empirical relation indicates an approach to randor distribution of magnesium in solid solution in aluminum with a tendency for magnesium segvegation which increases with incveasing temperature. ThE magnetic properties of metals are complicated by the fact that contributions are made to them both by electrons of a "metallic" type which belong to the crystal as a whole, and by electrons in states localized on particular atoms. An expression1'2 for the bulk magnetic susceptibility of aluminum may be written as the sum of three contributions: where XA1 is the bulk susceptibility of aluminum per gram of material (in the cgs system, the units are those of reciprocal density); Xa1+3 is the diamagnetic contribution of the electrons localized in ion cores; Xa1 is. the paramagnetic spin contribution of conduction electrons often called Pauli paramag-netism: Xa1 is the diamagnetic contribution of the conduction electrons often called Landau diamag-netism. Ion core diamagnetism arises from the precession of the electron orbits which occurs when a magnetic field is applied to a system of electrons moving about a nucleus. Its contribution to the magnetic suscepti- bility is small, temperature-independent, and unaffected by alloying. The conduction electron diamagnetism is also temperature-independent and arises from the translatory motion of the electrons. For perfectly free electrons this contribution should be exactly one-third of the Pauli spin paramagnetism, but this relation is seldom even approximately true. Blythe2 determined the conduction electron diamagnetism in pure aluminum and found it to be extremely small. Any change in the conduction electron diamagnetism caused by alloying is neglected in this work. The Pauli paramagnetic contribution3 to the magnetic susceptibility of aluminum depends upon the number of electrons that occupy excited states and whose spins can be turned parallel to an applied magnetic field. The number of electrons free to turn in the field is proportional to the temperature and each spin contribution to the susceptibility is inversely proportional to the temperature. A slight temperature dependence of Pauli paramagnetism occurs when the number of electrons occupying excited states cannot increase sufficiently to balance the inverse dependence on temperature of each spin contribution. The decrease of the magnetic susceptibility of aluminum with increasing temperature is attributed to a temperature dependence of the Pauli paramagnetism. Estimates of the Pauli paramagnetism of aluminum have been made by several workers.2,4,5 All of the values are in reasonably good agreement with each other. In this work Xal at 17°C is taken as 0.761 X 10-8 cu cm per g. An expression similar to [I] can be written for the magnetic susceptibility of an aluminum base alloy containing a fractional weight percent x of solute:' Xa = (1 -x)XAl+3 +xXsoluteion * XaPauli +Xadia) [2] where X, is the magnetic susceptibility per gram of alloy, Xal'3and Xsolute ion are the ion core diamag-netic contributions, and xpauli and xdia are the Pauli and diamagnetic contributions of conduction electrons in the alloy. If the components of a mixture are not alloyed but simply mixed together in their pure states without producing a new phase, then the magnetic susceptibility of the mixture is given by the Wiedemann additivity law: Xm =x1X1 +x2x2 + ..xnxp [3] where X, is the susceptibility per gram of mixture and xnXp are the weight fractions and susceptibilities, respectively,-. for the pure components. The additivity law is not applicable to alloys because the outer electronic structures of the components are changed by alloying.' Both the Pauli paramagnetism and Landau diamagnetism are affected; hence the magnetic susceptibilitv of an alloy is usually different from that calculated using the additivity law. In this work the difference, X, -X,, is taken as a measure of the change caused by alloying.

Jan 1, 1968

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

By James Gayley

The development of blast-furnace practice in America in the direction of large yields is mainly the history of our working since the year 1880, as the advancement that has been made in the last decade is greater than that in the third of a century previous. A new era in the manufactnre of pig-iron began in 1880 with the putting in blast of the Edgar Thomson furnaces. These furnaces at once leaped to the front as pig-iron producers, and have maintained that position—with but one brief interruption—ever since. I shall, therefore, confine myself mainly to a description of these works, showing the changes in design and practice by which these results have been achieved. In order to show more clearly the progress that has been made since 1880, I shall refer briefly to the best work that was done in the ten years previous to that time. The Struthers furnace, in Ohio, was one of the first to attract attention in the matter of large outputs. This furnace was 55 feet high, 16 feet in diameter of bosh, 9 feet in the hearth, and about 8 feet 6 inches at the stock-line. The fuel was raw coal. This furnace, in December, 1871, made 1602

Jan 1, 1891

By O. W. Ellis

THE writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.1 The copper referred to in his in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal, did not measure up to conductivity FIG. L -INGOT OF OVERPOLEP COPPER. standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the Westinghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 ½ in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of overpoling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By L. Russell, van Wert

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By van Wert, L. Russell

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1936

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880's, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940's. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By John V. Beall

New York was bathed in pale winter sunshine and, surprisingly, coatless weather. The time was the AIME Centennial and 100th Annual Meeting. From advance peeks into the fabulous schedule of events we were well aware that the Centennial Committee, New York Host Section and AIME staff' had pulled out all the stops, laying on the best of everything, but the weather gimmick was the frosting on the cake. The Formal Greetings Session on the first morning, Joe Alford confided, was the greatest AIME experience of his life. Without doubt the honor bestowed on AIME by the greetings and felicitations of the presidents of the world's leading professional engineering societies was the greatest moment in AIME history-save one. That one exception was in 1928, when 1920 AIME President Herbert C. Hoover was elected President of the United States.

Jan 1, 1971