Search Documents

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.' Previous investigators'' have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana' showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By Ellsworth Daggett

THE ore smelted in the Winnamuck furnace during the year 1872 consisted, for the most part, of oxidized ores from the Winnamuck mine, only sixty tons of outside ore (from the Spanish mine) having been smelted. The latter, like the principal Winnamuck ore, was oxidized or so-called carbonate ore. There was mixed with these oxidized ores three hundred to four hundred tons, or 7 to 10 per cent. of galena, some of which was mined with the oxidized ore, while a part was mined separately from the lower portion of the mine, and afterwards mixed with the ore, with a view of preventing the formation of deposits of metallic iron in the furnaces. The average assay in silver of all the ore handled was 51.46 oz. per ton, most of it existing as chloride of silver. The lead contents were 34.98 per cent., all, or nearly all, in the form of carbonate of lead. The relative amount of silver is not at all constant, the best silver ore often being poorest in lead. The predominant gangue was silica, several determinations of which have been made on representative samples, yielding in three such samples 26, 38, and 58 per cent. silica, the latter test being ore containing but little lead. The average contents in silica are about 35 per cent., with 6 to 7 per cent. sesquioxide of iron, and small quantities of alumina and lime. Mechanically, the ore was very fine, and so thoroughly disintegrated that it presented few distin¬guishing characteristics, rendering sorting or separating of ore from waste difficult, and often impracticable. Experiments on a small scale have been tried, with a view to separate the silica by washing; but these were unsuccessful, as the finest slime, requiring a long time to settle in still water, contained a large amount of silver; and on a careful sizing and washing of the sands and coarser parts, the silver contents were found to be less dependent upon specific gravity

Jan 1, 1874

By Ken Sublette

The mining industry has been a leader in the application of ultrasonic level monitoring systems, utilizing the "sonar-in-air" concept for the accurate inventorying of material not only as an end within itself, but going on to activate alarms, turn off feeders, operate tripper systems, and totalize the inventory in numerous bins as well as other more sophisticated applications. The virtues of ultrasonic level monitoring are no doubt appreciated by most users. However, to be of maximum service to the expanding mining industry, the manufacturer must be fair in pointing out ultrasonic's limitations as well as its virtues. The limitations can be surmounted with new technology and through a proper understanding of the principles of operation and application.

Jan 6, 1974

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally.' Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan,3 show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision; using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by, the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.5 However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: [3fB = 9.20•'./V•Vn- (n-1) • (n+2) /8[1]] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts' as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of, a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsymmetric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat I than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system, of one degree of freedom can be applied: [1E/m[2] fP = 27] Here f, is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: [t~ = 2/f = 7r\/m/E[3]] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson' 1831) [aP = 4 D2.pL•g•h +7rD•y sin a[4]] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, pL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of-the liquid in cm, y the surface tension in dynes per cm and a the supporting angle' or the one required to insure equilibrium, a being smaller than the contact angle ?. Although demonstrated by Poisson, it has not

Jan 1, 1952

By Arthur Redfield

THE year 1923 was marked by slight progress in exploring and developing the petroleum resources assumed to exist in Central America. Actual drilling for oil took place only in Costa Rica and Panama. The Sinclair Consolidated Oil Corpn., through its subsidiary the Costa Rica Oil Corpn., drilled in southeastern Costa Rica.. Its, Panaman subsidiary is reported to have abandoned drilling in Bocas del Toro. The Texas Co. drilled in Chiriqui, and the Panama Gulf Co. in Garachiné, Province of Darién. No oil was obtained in any of these wells;' shows of gas were met in Costa Rica. Concession hunting continued during the year. A number of concessions, several of which appear to be purely speculative, were submitted for ratification. Some confusion has been caused by overlapping concessions and claims to oil lands, caused partly by the imperfection of existing maps. A conflict between the Sinclair, and Gulf companies in Panama has been compromised. The Amory concession in central Costa Rica, held by the British Controlled Oilfields, Ltd., was voided by decision of the arbitrator, Chief -Justice Taft. Geologic exploration took-place in Guatemala and in Panama. The chief contribution of the year to Central American geology was a description by Katherine Van Winkle Palmer of Lower Miocene foraminifera and mollusks from southeastern Costa Rica. A new petroleum law was promulgated in Panama.

Jan 3, 1924

By Jim V. Rouse

In situ mining and dump leaching has been practiced for years. Recent environmental concern over conventional mining and milling techniques has rendered in situ mining more attractive. While there are many environmental advantages to in situ mining, there are disadvantages which, if ignored, can lead to environmental damages, followed by stringent control. The environmental advantages and disadvantages of the various types of in situ mining operations are discussed. Current legislation and regulations governing in situ mining are cited, together with a suggested program of environmental monitoring designed to protect the mining company as well as the environment. Suggestions are made for possible solution of existing pollution problems associated with previous mining activities by heap-leaching techniques. Present and indicated control of subsurface injection is traced, because of the many similarities in philosphy and monitoring requirements to in situ mining.

Jan 1, 1974

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1917, to July 10, 1917. BANKS, LEON MAXWELL Agent 3. Supt., Grant Leasing Co. Metcalf Ariz. BEAUCHAMP, HENRY CLAY : Mine Operator, Sisson, Siskiyou Co., Cal. BOCKING, CHARLES, Asst. Mgr., Butte & Superior ,Mining Co., Rialto Bldg., Butte, Mont. BEYER, HERMAN E., Chief Engr., Condenser Dept., Ingersoll-Rand Co., 11 Broadway, New York, N. Y. BLACK, HERBERT F 1512 Oliver Bldg., Pittsburgh, Pa. BRENNAN, PATRICK J., Gen&apos;l. Supt., Elkhorn Division, Consolidation Coal Co., Jenkins, Ky. BUTNER, DANIEL W., Chem. & Supt., Underground Min., Spanish American Iron Co., Daiquiri, Santiago de Cuba, Cuba. CARLTON, DAVE P Nevada-Douglas Cons. Copper Co., Ludwig, Nev. DE AROZENA, JOE Min. Engr., 321 Preusser St., San Angelo, Texas. DICKIE, CHARLES HERBERT, Pres., Georgia River Min. Co., Duncan, Vancouver Island, B. C., Canada. DOBBINS, WALTER Mill Foreman, Chino Copper Co., Hurley, New Mexico. DRURY, CHARLES W., Asst. Professor of Met., Queen&apos;s University, Kingston Out. Canada.

Jan 8, 1917

By Kendall E. Born

Production of crude oil in Tennessee during 5945 was slightly more than 6000 bbl., the lowest figure since 1916. Approximately 5500 bbl. was produced from the "Mississippi lime" in Scott and Morgan Counties. The remainder was from two wells each in Clay and Fentress Counties. Thirty million cubic feet of gas was marketed off the lease in Morgan County and about 10 million cubic feet was produced in the Jamestown field in Fentress County. The production of oil by counties is shown in Table 1.

Jan 1, 1946

By R. P. Smith

IN 1937 the employees of the Hollinger Consolidated Gold Mines Ltd., at Timmins, Ont., Canada, approached organized medicine for a plan to provide themselves and their families with a complete medical service including hospitalization. This approach was made because of two conditions: (1) the necessity for some organization whereby contributions could be made in instalments to offset the sudden and large expense connected with illness for which the average employee is not prepared, and (2) the need for a more cohesive quality of service to replace a contract practice then in vogue, which did not take care of the employee&apos;s family or dependents. In different parts of the United States and Canada similar plans were in force, not only for employed groups but for numbers of people in circumscribed areas. In Europe different countries had adopted various forms of health insurance plans. It then was no surprise that these employees as a group should ask for some similar plan. With the cooperation of the management, a plan was instituted. The plan has one object only-the provision of medical services, including the accessory services such as hospitalization, X-rays, nursing, and necessary drugs and medicines. It is not concerned with cash benefits, sickness and accident payments, or any form of monetary return as the result of illness, but is simply an organization to provide medical services and pay for them from a central fund. It is a nonprofit organization and the only shareholders are the employees and their families who contribute and who in turn receive services. The Hollinger plan is limited to the employees of the Hollinger mine, who live in Timmins and the immediate vicinity. At first, the membership was voluntary. In the third year, it was made a condition of employment, with the proviso that at the end of any Association financial year an employee may withdraw if he wishes to do so. After withdrawal, he cannot again become a member until the end of the next Association year, and then only by the payment of the back dues. This step was taken to ensure continuity, and to prevent employees from withdrawing when well and reentering when faced with impending illness or operations. The employee himself is subject to medical examination on application for employment, and if accepted is subject to further examination by a specialist in chest diseases under the Workmen&apos;s Compensation Board of Ontario. Thus it is possible to exclude those who have heart disease, tuberculosis, or other disabling conditions when first employed. Wives and families of employees are not subject to medical examination but other dependents of an employee-mother, father, or other relative-who are declared by the employee to be wholly dependent upon him must be examined. The employee

Jan 1, 1944

By G. Sachs

THE iron-rich iron-nickel alloys have at-tracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are Atomic per cent nickel FIG. I. FIG. 2. FIG, I.-HONDA&apos;S AND MERICA&apos;s IRON-NICKEL DIAGRAM, FIG. 2.-MARSH&apos;S IRON-NICKEL CONSTITU-TIONAL DIAGRAM. the base of many alloys with various out-standing properties. The iron-nickel alloys, therefore, have been investigated exten-sively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,1 and will be discussed in some detail in the sec-tions of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis,2 which is not dependent upon

Jan 1, 1940

By J. Jolly, R. V. Wheeler

This short note on the probable character of the organic sulfur compounds in coal can do no more than indicate lines of research. We have no new experimental work to describe, nothing comparable in value with the careful studies of American coals by Powell and Parrl and Yancey and Frazer. A study of the manner in which sulfur compounds exist in British coals (and their behavior on heat treatment) is rendered increasingly necessary by the fact that the British reserves of good coking coals of reasonably low sulfur content are fast being depleted. We believe that it is essentially by a study of the modes of formation, occurrence, and decomposition of the various types of inorganic and organic sulfur compounds in coal that it will be possible, with hope of success, to attack the problem of purifying coals, otherwise eminently suitable for coking, from these objectionable ingredients. Sulfur, so far as is at present known, does not normally occur in the free state in the coal conglomerate, but is chiefly distributed, irregularly, in three forms : 1. As primary constituents of the coal conglomerate, organic in nature and probably associated with those molecular complexes that have resulted from the degradation of the proteins of the plant tissues responsible for the formation of the coal mass. These constituents can be classed as "organic sulfur." 2. As metallic sulfides, e.g., iron pyrites. 3. As metallic sulfates, e.g., calcium sulfate and ferrous sulfate. (The occurrence of these compounds varies with the occurrence and degree of degradation of class 2.) It is usually found that sulfur compounds of class 3, the metallic sulfates, are present in coal in small proportions only, amounting to about 1 or 1.5 per cent. of the total sulfur. The compounds in classes 1 and 2 are therefore of more importance. Class 1 alone will receive considera-

Jan 1, 1925

By M. E. de Morton

Low frequency-internal friction measurements on annealed chromium have shown a marked increase in damping below - 40°C which is strongly strain amplitude dependent. An interpretation of these results is given in terms of the motion of antiferromagnetic domains assumed to exist below - 40°C. A time effect on internal friction was measured after slight overstraining. After heavy deformation a pemzanent, five-fold increase in internal friction was observed at -45°C and the character of the internal friction us temperature curve markedly changed. Full recovery of damping was not attained until after heating to 800°C. A qualitative interpretation of some of these effects is given. THE aim of this preliminary investigation was to study the internal-friction characteristics of chromium containing comparatively small quantities of interstitial solutes in the fully annealed and heavily worked condition. Marked anomalies in a number of physical properties of chromium at temperatures near 40°C have been observed1 and an investigation by neutron diffraction&apos; has shown that chromium at room teyperature is weakly antiferromagnetic with a Nee1 temperature at approximately 200oC. No irregularities in the degree of antiferromagnetic ordering have been observed at -40°C, the transition temperature, and a complete explanation of this transition in chromium is still awaited. Recently weiss3 has suggested that an ordering effect of nitrogen in the face-centered interstices of the bcc lattice of chromium could be responsible for the superlattice detected below 200 °C in the neutron diffraction experiments. EXPERIMENTAL MATERIAL AND METHOD Specimens 10 by 0.030 in. diam were prepared from ingots of arc-melted electro-deposited chro-

Jan 1, 1961

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948