Search Documents

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By V. R. Garflas, J. W. Ristori, R. V. Whetshel

Preliminary estimates indicate that world consumption of petroleum products and related fuels in 1937 shattered previous records with a figure of 1,920,000,000 bbl.; that is, 124,000,000 bbl. more than the 1936 total. The writers, as in previous years, have been unable to account for all the available supply in 1937. This "unaccounted-for" supply, which formerly was thought to go largely into storage in foreign countries, was close to 53,000,000 bbl. in 1933; 93,000,000 in 1934; 111,000,000 in 1935; 75,000,000 in 1936 and 148,000,000 in 1937. As this discrepancy between supply and demand continued year after year, it became evident that other reasons than additional foreign stocks were responsible for it. It can now be stated that the "unaccounted-for" supply (see Table 1) goes to take care of: (1) consumption of petroleum products and related fuels for military purposes, the figures of which have been and are kept confidential by foreign countries, (2) additions to stocks to be consumed for military and nonmilitary purposes in foreign countries on which likewise no information is available, (3) errors incurred in the conversion of figures of production of crude oil, its products and related fuels from "weight" units, as used in Russia, for instance, to their American or "volume" equivalents and vice versa, and (4) to the lack of reliable statistics on production and consumption, particularly from Russia, the

Jan 1, 1938

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By G. Bhat, J. F. Libsch

A STUDY of the kinetics of embrittlement in engineering alloy steels during tempering has indicated that the presence of alloying elements may define two distinct regions of embrittlement: 1) at 800° to 1000 °F, termed low temperature embrittle-ment, and 2) in the temperature range 1150 ° to 1250°F, termed high temperature embrittlement.13 It has been suggested that embrittlement in each region may be due to a different mechanism. At intermediate temperatures and extended times the course of embrittlement may be influenced by the superposition of the embrittlement occurring in the two regions. Furthermore, low temperature embrittlement has been known to decrease as the temperature is raised slightly above the maximum embrittlement range.' Jaffe and BuffumV ave presented data for a Ni-Cr steel illustrating the removal of the em-brittlement occurring at 932°F by reheating to 1250°F for an hour. Their data further shows that embrittlement proceeds continuously with increased time at 1250°F, becoming pronounced at long times. They interpreted this behavior as a retrogression phenomenon involving the solution of the small nuclei of precipitate formed at 932°F as the temperature was increased, and reprecipitation of larger nuclei stable at 1250°F, with the reoccurrence of embrittlement. It appears desirable to reconsider this explanation in the light of the two regions of embrittlement proposed by the authors1 for some alloy steels. In addition, it appears desirable to determine any influence of a preconditioning treatment in each temperature range upon subsequent development of low and high temperature embrittlement. It is thus the object of this investigation to study the characteristics of the two modes of embrittlement proposed in a commercial Ni-Cr alloy steel (AISI 3140). Experimental Details Material—The material used in this investigation was commercial AISI 3140 steel bar stock, received as % in. hot-rolled rounds. The steel analysis was as follows (in percentages): C, 0.39; Mn, 0.79; Si, 0.30; S, 0.028; P, 0.015; Ni, 1.26; and Cr, 0.77. Material Processing and Heat Treatment—The bar stock was first ground to 0.430 in. squares and cut into specimens 23/4 in. long. These specimens were austenitized at 1650°F for 1 hr and oil

Jan 1, 1958

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By H. T. Van Ells

The following is a brief description of the cost accounts in effect at the mines of the Anaconda Copper Mining Co. The accompanying chart, Table I., shows the distribution of labor, materials, and redistributable accounts to the various operating and repair accounts. OperatiNG. Development. Owing to the fact that every mine has its peculiarities in formation and methods, the question of arriving at what charges should be included under the head of " Development" is one that has occasioned considerable thought and comment, and in the cost sheet of the Anaconda Copper Mining Co. this account has been sub-divided to show the expenses of breaking ground, tramming, timbering, shaft sinking, up-raising, and cutting stations and skip chutes. It has always been the policy of the company to charge the entire cost of this work to operations monthly, whether the mines are producing or not, also the cost of the opening up of new mines; and only surface construction and additions are charged to capital, excepting original machinery installed for operating pumping plants. Explanations of the charges to the various sub-accounts follow : Breaking Ground.—Work performed in driving cross-cuts from the station, or cross-cuts from the drifts, and diamond-drill work, for the purpose of discovering or developing ore bodies. Tramming.—Cost of tramming waste produced by cross-cuts mentioned above. When waste is hoisted to another level to be used for filling, the charge to this account stops at the station, and when hoisted to surface the charge includes tramming from the collar of the shaft to the dump. Timbering.—Cost of timbering the cross-cuts mentioned above includes the cost of handling and framing such timbers, but does not include the wages of station tenders and top carmen.

Jan 1, 1914

By H. C. Spaulding

The rapid increase, during the last few years, in the number and magnitude of applications of electric power-transmission to commer cial uses in this country, has been due principally to three causes: first, the ability and enterprise of those who have been identified with the progress of electrical industries, since electric illumination became an economic fact instead of a laboratory-experiment: sec ondly, the readiness of the American people to adopt new and ad vanced methods as soon as their superiority has been fairly demon strated; and thirdly, tile economy and flexibility of the apparatus employed, when properly designed and constructed, and installed under suitable conditions. Basing our judgment on the world's advance in scientific devel opments during the past century, we may reasonably conclude that in no other country would the pioneeis of electrical invention, whose names have now become household words, have received the prompt and plentiful financial support which has enabled them to inaugurate undertakings of exceptional magnitude, even in this era of tremendous monetary organizations. And, on the other hand, we have seen, in the numerous financial and engineering failures inseparable from such rapid development, the natural results of a too implicit faith in electrical omnipotence. It is not to be wondered at that conservative engineers have been slow to adopt this new and mighty agent in the solution of exten sive problems, and under circumstances where a single failure means not only a greater or less financial sacrifice, but the loss, in a greater or less degree, of professional reputation. Be mechanical engineer, while recognizing the fact that thousands of horse-power are to-day transmitted by electrical means, from sunning the lathe in a dentist's office to the operation of a fifty-ton travelling crane; from passing a cooling draught of air through a

Jan 1, 1891

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many. compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides, polysulfides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By Thomas T., Read

THE education of adolescents to perform the duties and assume the responsibilities of maturity has been a characteristic of human society since the dawn of history. In the beginning the members of the immediate family performed this function, and in modern life they still have an important part in it. Possibly religion was the first field in which education began to be functional; young people were sent for instruction to a teacher who had a broader and deeper knowledge of the subject than was possessed by the family. It does not seem necessary for our purpose to attempt to determine how, when, or where instruction in the practical arts first' began to become functional, and the brief outline which follows must suffice. The discovery and utilization of mineral substances to improve and maintain the conditions of human living is a practical art, which must have had an almost accidental origin and have been developed by empirical experiments. We do not know, nor would it be useful to try to fancy, how men first learned that they could make use .of mineral substances to their benefit, but how- ever that knowledge was initially gained it was certainly trans mitted through instruction in the family. At first such activities must have been merely a .minor part of the making of a-living, but in time those who excelled found it better to devote them-

Jan 1, 1941

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By E. B. Thornhill

Discussion of the paper of E. B. THORNHILL, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1653 to 1670. D. B. HUNTLEY, Oakland, Cal.-About 15 years ago it chanced to be my lot to cyanide some mill tailings, assaying about $5 per toll in gold and, a few cents in silver. It was in southern Idaho, a. desert region where costs are nearly as large as in central Nevada. We knew that we had a lot of tailings that had been amalgamated and contained about 1 lb. of quicksilver per ton. We knew that we would dissolve some of the quicksilver when we cyanided them with say 0.25 per cent. cyanide solution. We figured (optimistically) that the cyanide would dissolve all of the quicksilver, and we thought to capture all of that, 1 lb. per ton; and we figured out profits as partly gold, partly silver, and partly quicksilver from the recovery in working those tailings. Actually, however, we did this: We had a battery of three large, old-fashioned silver-mill retorts. We retorted our zinc-dust precipitate, recovering about ¼ lb. of quicksilver per ton treated. That was only a loss of 75 per cent. of what we originally had, but still it was profitable by virtue of the conditions. I mention it partly to call attention to the crude old way of doing it, and partly to call attention to how chemical methods for recovering quicksilver have developed in the last 15 years.

Jan 12, 1915

By M. M. Fine

In a laboratory study of grinding and classification of silica sand, a satisfactory means of producing the medium-fine specification sand desired by producers of flint-glass containers was developed. The best procedure consisted of ball-mill grinding and double classification, which gave a properly sized sand containing less iron than the feed.

Jan 3, 1950

By William H. Spice

No devclopment of major importance has been made in the south central fault-line district of Texas during 1939. Four new fields have been discovcred, all of which appear to be of minor importance, with small wells in the Navarro sand, the Taylor marl or the Austin chalk. Drilling along the fault line has not developed any new prospects in the Edwards lime, the most prolific producing horizon of the district. At the close of the year, a few deep tests for lower producing horizons have been projected and should prove to be of interest, and plans are under way for further development of the Pearsall field, which has been under the control of a single company until recently. Production from the 46 producing fields was maintained at 8,460,000 bbl. for the year, a decrease of approximately 400,000 bbl. under 1938. This decrease is due in part to natural decline of production and in part to decreased allowed production. Approximately 55 producing wells were completed on proven acreage in the Darst Creek and Salt Flat fields. No new lease plays were made during the year, although approximately the same amount of land, 600,000 acres, remained under lease during the year. Some geophysical operations of various types were carried on along the fault-line area itself and also in the Edwards plateau and in the area south and southeast of the main fault line.

Jan 1, 1940

By William H. Spice

No devclopment of major importance has been made in the south central fault-line district of Texas during 1939. Four new fields have been discovcred, all of which appear to be of minor importance, with small wells in the Navarro sand, the Taylor marl or the Austin chalk. Drilling along the fault line has not developed any new prospects in the Edwards lime, the most prolific producing horizon of the district. At the close of the year, a few deep tests for lower producing horizons have been projected and should prove to be of interest, and plans are under way for further development of the Pearsall field, which has been under the control of a single company until recently. Production from the 46 producing fields was maintained at 8,460,000 bbl. for the year, a decrease of approximately 400,000 bbl. under 1938. This decrease is due in part to natural decline of production and in part to decreased allowed production. Approximately 55 producing wells were completed on proven acreage in the Darst Creek and Salt Flat fields. No new lease plays were made during the year, although approximately the same amount of land, 600,000 acres, remained under lease during the year. Some geophysical operations of various types were carried on along the fault-line area itself and also in the Edwards plateau and in the area south and southeast of the main fault line.

Jan 1, 1940

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By G. W. Healy

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963