Search Documents

By Francis M. Walters, Irvin R. Kramer

THE substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient of expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and [ ] their use up to 400° or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. EXPERIMENTAL METHODS Two methods were used in studying the stability of the low-expansion iron-nickel-cobalt alloys. Dilatometer specimens were held at 480°C, for 9 months and the change in expansion characteristics was determined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection [ ] temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1941

By Rudolf Gahl

Page Tests Conducted in Small Test Mill................... 577 Demonstration Tests Conducted by Minerals Separation Co....... 577 Flotation Tcsts Conducted by Inspiration Co............. 577 Sampling of Orebody........................ 578 Other Results Obtained in Small Test Mill.............. 580 Tests Conducted in Large Test Mill................... 580 Flow Sheet............................. 580 Discussion of the Value of Preliminary Table Treatment......582 Callow Flotation Installation..................... 585 Flinn-Towne ~nstallation...................... 587 Cole-Bergman Installation...................... 588 Methods Followed in Competitive Tests................ 590 Advantage of Pneumatic Flotation Machines.............. 591 Pneumatic Machines of Minerals Separation Co............. 591 Float Skimming Device......................; 594 Experimental Inspiration Flotation Machine.............. 596 Arrangement of Callow Cells in Series ................ 598 Variations of Flow Sheet....................... 599 Coal Tar as Flotation Agent..................... 600 Experience with Primary Slime.................... 602 Influence of Iron on Flotation..................... 605 Influence of Chemicals on Primary Slime............... 607 Fineness of Crushing Desired.................... 607 Operation of Large Concentrator..................... 608 Flow Sheet of Callow Sections.................... 608 Flow Sheet of Inspiration Sections.................• 609 Inspiration Flotation Machine of Steel Construction.......... 610 Minerals Separation Section..................... 613 Filter Plant............................ 613 Results Obtained in Commercial Concentrator............... 616 Tonnage............................... 616 Air and Power Consumption...................... 616 Floor Space............................ 617 Water Consumption......................... 617 Recovery............................. 618 Oil Consumption.......................... 618 Operating Costs for Flotation..................... 620 Discussion of Results Obtained.................... 620 Prospects for Futurc Development of the Flotation Process......... 621 Porous-Bottom Experiments..................... 622 Raising the Grade of Concentrates.................. 624 Recovering Carbonates by Flotation................. 624 Recovery of Silicates by Flotation.................. 627 General Theory......................... 628 Conclusion............................... 630

Jan 1, 1917

By George Stone

THE method of making oxide of zinc direct from the ore was invented and developed at the works of The New Jersey Zinc Co. at Newark in the middle of the last century. The process was invented by Burrows, who had not the ability, financial or technical, to work out the details necessary to make it of commercial value. This was done by Col. Wetherill, whose name is commonly attached to this process. The, grate bars used are also frequently called Wetherill grates, which is a misnomer because they were in common use for boiler firing at the time and he never claimed their invention. The invention of the process was due to the efforts of The New Jersey Zinc Co. to find a profitable means of working the ores from Franklin and Sterling Hill, N. J. These are a mixture of franklinite, willemite and zincite, containing about 20 per cent. of zinc. The first attempts were to make spelter, which were not successful, owing to the low grade of the ore and the fusibility of the residue. Failing in this, the next attempt was to make oxide in large muffles and reverberatory furnaces. This succeeded, although the cost of operation was high, the recovery low, and the quality of the product uncertain. In 1855, the new process was patented and has been in successful operation ever since. Essentially, the process is to spread a mixture of coal and ore on a body of burning coal on a perforated grate and blow an excess of air through the grate. The zinc is reduced in contact with the coal, volatilizes and burned by the excess of air in the upper part off the furnace and in the flues. It is then carried to the hag rooms by the excess air and products of combustion which are forced through the flues by fans. In its main features, the process is the same today as at the time of its invention, but the details have been so modified that it would hardly be recognized by its originators.

Jan 9, 1917

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By L. S. Chabot

INTRODUCTION THE bibliography of mining methods in the past few years has contained many articles dealing with the use of the diamond drill for blasthole drilling. In the Canadian mines, this method has been used with great success in stoping at Noranda, Aldermac, Waite Amulet, East Malartic and Sladen Malartic mines in the Province of Quebec. It has also been used at the Dorchester and Beattie gold mines in Duparquet, Quebec. The method has found useful application at Copper Mountain mine, British Colombia, and at Flin Flon mine in Manitoba. In the United States, the diamond drill blasthole method has been used at Cornwall Iron Ore Mines in Pennsylvania and at the Republic Steel Corporation magnetite properties in the Port Henry district of northern New York. In the Lake Superior iron district, the method has been used at the Anvil-Palms mine of Pickands, Mather and Co. at Bessemer, Mich., and is also used at the Book mine of the North Range Mining Co. at Alpha, Mich. Other companies in the district have also experimented in some degree with the method at some of their properties. This paper is being offered as a preliminary report on the use of the diamond drill method of stoping at the Book mine. Sufficient work has been done with it to prove its worth and it is the purpose of the article to present some results, operational details, equipment ideas and recommendations which we have found in its use at our mine. LOCATION AND DESCRIPTION The Book mine is situated about a mile north of the village of Alpha, in the NE-NE ¼ and the SE-NE ¼ of sec 12-42-33, between the Dunn mine and the Balkan-Judson mine, and about four miles southwest of the village of Crystal Falls, on the Menominee Range of Michigan. The property was found to have ore near surface in sufficient quantities for open-pit operations and stripping was begun in the latter part of 1942 to prepare it for ore production in 1943. During 1943, 288,447 tons of direct shipping ore were produced from the open pit and 382,933 tons in 1944. While the mine was being operated as an open pit some 350,000 tons of lean ore were stockpiled for later treatment. This material is being treated in a washing and jig plant and concentrates are produced during the shipping season. The ore bodies at the Book mine are characteristic of the Menominee Range. They are found on the flanks of sharply folded anticlines which have a fairly steep pitch to the northwest. The open-pit operations in 1943 and 1944 revealed two of these anticlinal structures. A detailed study and classification of the old diamond drill records, coupled with the information of some new holes drilled, has established the

Jan 1, 1947

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By J. L. Jernegan

In a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaftfurnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the varions metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

By D. W. Fuerstenau, D. A. Sullevan

In the experimental work for this comparison of wet and dry grinding, it was found that the size distributions for wet grinding operations are characterized by a constant value of the distribution modulus, (a; whereas, for dry grinding the distribution modulus decreases slightly with increased size reduction. Wet grindability seems independent of the weight of material in the mill while dry grindability depends on weight. Experimental data and eqmtions for each process are presented for noncleavable isotropic material, for cleavable or material in which there is some form of internal stress, and for energy consumption. The equation ED/EW=BK-? (where ED and Ew are, respectively, energy for wet and dry grinding, k is the size modulus, and B and ? are constants) was found to give the ratio of energy. Dry grinding is generally considered to require more energy than wet grinding. Taggart' states that power consumption in wet grinding ranges from 60 to 90 pct of that required for dry grinding. Bond' states that dry grinding requires one third more power than wet grinding. It is interesting that Rose and Sullivan' note this same difference in power required for wet and dry grinding, but they state that on purely mechanical grounds it is difficult to see any great difference in fundamental principles between wet and dry milling, since dry milling may be regarded as wet milling with a fluid of low viscosity (i.e., air vs water). Yet it must be the viscosity of the fluid that is responsible for the differences between wet and dry grinding. Probably the most comprehensive investigation comparing wet and dry grinding has been that made by Coghill and Devaney. They compared the grind-ability of both chert and dolomite in a 19x36-in. batch ball mill under both wet and dry conditions. In these tests the weight of ore in the mill was varied from 35 to 200 lb and each grinding test was carried out for such period of time that the amount of -200-mesh material in the product was essentially the same for each test with a given material. Cog-hill and DeVaney's data for the grindability of dolomite, which are reproduced in Fig. 1, show that a comparison between wet and dry grinding is com- plex. The comminution of a material by a wet grinding method is characterized by a constant grindability over a wide range of mill loadings. Since grindability is the weight of material comminuted per unit of energy expended, it is equivalent to (w)/ (p)(t), where W is the weight of material being ground, P is the power, and t is the grinding time. In the case of wet grinding, the grindability of dolomite in the Coghill and DeVaney experiments was 0.546 * 0.009 ton per hp-hr when the load of dolomite in the mill ranged from 50 to 200 lb. On the other hand, for dry grinding no such simple relationship was found to exist between power, time, and weight of material in the mill. Dry grinding efficiency appears to depend greatly upon the amount of material within the mill. When the mill contained

Jan 1, 1961

By Frederick Laist

This paper is a review of Montana reverberatory smelting practice covering a period of approximately fifty years, during which time the small furnaces that had been in use elsewhere for a century or more, without much change in size or method of operation, were revolutionized and were developed into the huge, continuously operating furnaces of today. A study of Montana practice is particularly instructive, since reverberatory furnace smelting for the production of copper matte received more attention there than in other smelting centers and many of the improvements that finally resulted in establishing the preeminence of this type of furnace over the blast furnace originated in Butte and Anaconda. The material in this paper was gathered from original sources, wherever possible, and all of the illustrations were made from original drawings, some of which have been simplified and worked over so as to be better adapted for reproduction. The aim has been to trace the modifications in design and operation which took place during the period in question—the reasons for the changes and the results achieved through them. For developments during the first twenty years, the technical literature of the period was freely drawn upon, but I am particularly indebted to W. M. Kelly, general foreman at the Anaconda Works, whose recollections and personal experience extend back to the early days. I wish to acknowledge the use made of publications of E. P. Mathewson, William Wraith and L. V. Bender, as well as information obtained here and there from friends and associates. The resume of Great Falls practice was compiled from correspondence, notes and drawings found in the files of the old Boston & Montana Co. and the tabulations showing the performance of furnaces at Butte and Anaconda are adapted from plant records and correspondence in the files of the Anaconda Copper Mining Company. The paper deals with some interesting comparisons that were made between furnaces operated under various conditions in connection with the Carson Case, and results obtained when using natural gas as fuel. This part of the paper may be considered original to the extent that these results have not previously been published.

Jan 1, 1934

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur' Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur' Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

By R. Janes, F. Everard

Pilot plant studies have been conducted on a variety of iron ores of differing composition and grain size to test their amenability to dry autogeneous grinding and dry magnetic concentration. A general description of the pilot plant and its equipment is given with particular reference to the Aerofall mill and the dry magnetic separators developed by the Ontario Research Foundation. Test results are reviewed in detail with emphasis on power consumption, mill speed, the use of ball charges, types of ores, moisture content, separator speeds, and design. In 1957 the Ontario Research Foundation installed a pilot plant (Fig. 1) for the study of dry autogenous grinding and dry magnetic concentration of iron ores. A 61/2-ft Aerofall mill was installed as the dry autogenous crushing and grinding medium. The Cavanagh fast drum and the Double Helix, two dry magnetic separators developed at Ontario Research Foundation, were also installed. Iron ore samples of 10 to 150 tons have been investigated. These ores varied widely in mineralogy and grain size. Taconite (-325 mesh), fine-grained magnetite (200 to 325 mesh), and medium-grained magnetites (65 to 150 mesh) have been treated with varying degrees of success. Lately, considerable research has also been conducted on the metamorphosed magnetite-hematite complexes of the Labrador Trough. Operational and metallurgical data have been compiled from these tests. The effects of ore type, air flow, mill speed, and ball charge on mill operation are discussed. Metallurgical data are also presented to illustrate the operation of the dry magnetic separators. PILOT PLANT DESCRIPTION Fig. 2 depicts the normal flowsheet used. Minus 6-in. ore from a vibrating feeder is fed to the 6%-ft Aerofall mill powered by a 50-hp 550-v induction motor. The main blower, a 25-hp 550-v fan rated at 7000 cfm, draws air through the mill. Finely ground ore is conveyed by the air stream to a horizontal classifier, where expansion and a change in direction cause the +I50 mesh fraction to fall onto a vibrating

Jan 1, 1962

By Walter R. Crane

Operators of diamond drills have long been familiar with threadlike markings or riflings on cores but apparently have given but little serious thought to the conditions that are responsible for their production. The opinion generally held by those who have observed the phenomena is that the riflings are produced directly or indirectly by vibration, but so far as the writer is aware no systematic attempt has been made to demonstrate the fact. A careful search through the literature on diamond-drilling practice has been rewarded by only one reference to such markings of cores. J. N. Justice1 writes, "Of the peculiarities met with in the core, I will mention only one. The core from the "H" drill, at about 360 ft. came out rifled and pentagonal. The change from the circular to the pentagonal was sudden, and for 9 ft. this structure was maintained, when suddenly it returned to the circular. I have not been able to find any one who can explain the cause of this change of form. The drill men marveled at it and suggested vibration, six-stone bits, and several other hypotheses which need not be mentioned." The writer became interested in the matter of core riflings some 10 years ago while in the Flat River lead region of Missouri, where many remarkable examples of "rifled" cores were observed and collected. Since that time similar phenomena have been observed in various localities throughout the United States and Canada, and samples have been gotten together illustrating a large number of variations in form. After a careful study had been made of the material at hand it seemed desirable that certain data should be obtained from the experience of others regarding the normal action of diamond drills in forming cores, portions of which are occasionally rifled, before an attempt was made to draw any conclusions as to their cause. About 20 letters were addressed to diamond-drill companies, operators, and engineers actively engaged in drilling operations, with a

Jan 1, 1917

By AIME AIME

THE many kinds of iron and steel may be grouped into two general classes. First, there are the common steels and cast irons, made in enormous tonnages each year and used for the construction of buildings, ships and bridges, for pipe, for reinforced concrete highways, for the so-called tin cans, and by the railroads and other industries for which a low cost material is suitable. Second, there are the alloy steels and alloy cast irons, which are alloys of the chemical element iron and one or more of a large number of special elements such as manganese, silicon, nickel, chromium, vanadium, tungsten, and molybdenum. Alloy steels and irons are more costly than the common grades but their higher cost is, for many applications, justified by their superior properties, leading to ultimate economies or other advantages. They may be harder, stronger, tougher, or more resistant to rusting than the common varieties, and so are extensively used for tools, for ornamental work on buildings and in the automotive, aircraft, and other industries for, which the higher cost is compensated for by the higher quality.

Jan 1, 1933

By Wilfrid R. Foster

The industrial importance of the sillimanite group of minerals depends upon the beneficial properties exhibited by porcelains and refractories in which substantial amounts of these minerals are utilized as raw materials. The presence of "sillimanite" (now known to be the closely related mineral, mullite) in conventional porcelains and refractories has been known since before the turn of the century. As early as 1906 German investigators observed a direct correlation between the "sillimanite" content of a porcelain and its electrical and mechanical properties. Acting upon this discovery, U. S. Bureau of Standards investigators during World War I developed improved pyrometer tubes and spark plug porcelains, by increasing substantially the amount of "sillimanite" at the expense of quartz. The success of these experiments, first reported in 1918, at once aroused a lively interest in the location of natural sources of sillimanite and its related minerals. As a result of diligent search, the large andalusite deposits in California were discovered in 1919. Within the next several years large deposits of kyanite and sillimanite in India and kyanite in the United States had been reported. The search for these minerals in quantity, by both private and governmental agencies, has continued unabated during the ensuing forty years. A number of domestic deposits of kyanite have been worked during the past 30 years. Of these, only the Virginian and South Carolinian deposits are currently in substantial production. The only commercial andalusite production in the United States has been in California and Nevada. A dumortierite deposit in Nevada, known since 1917 but ignored for want of a commercial use, began production in 1925. A topaz occurrence in South Carolina has yielded a small production since about 1940. Domestic production of andalusite, dumortierite and topaz had virtually ceased by 1950. There has never been any commercial development of domestic sillimanite deposits. Kyanite has been mined almost continuously in India since about 1922. The remoteness of the large deposits of Indian sillimanite had caused it to be neglected until 1949. In that year sillimanite production began, and it has continued to the present. South African andalusite has been marketed from the 1930's until the present time. From 1944 to 1955 Kenya, British East Africa, was an important producer of kyanite. Commercial deposits of kyanite in Ontario, Canada should soon be in production. The first production of kyanite in Europe began in Austria in 1953. No commercial deposits of mullite are known anywhere in the world. It is of interest to note that synthetic mullite, which as "sillimanite" first elicited interest in the A12O3-rich aluminosilicate refractories, has enjoyed a marked increase in production in recent years. This is a result of the gradual depletion of known deposits of high-quality kyanite and related minerals."' Composition The sillimanite group includes kyanite, andalusite, and sillimanite, all having the same chemical composition (A12O3•SiO2) but different physical properties. Two other minerals, dumortierite and topaz, are also included in

Jan 1, 1960

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By Z. E. Arlin, R. D. Lynn

The problem of disposing of excess waste water coming from The Anaconda Co.'s two uranium mills in Grants, N. M., first confronted the company's engineers in 1956. The increased discharge of mill waste water was due to the start-up of a second mill, recently completed to supplement production from a smaller plant which the company had operated since 1953. The waste water is mildly acidic and has a low level of radioactivity due to small amounts of uranium-natural, thorium-230 and radium-226. In addition, it contains large amounts of manganese, iron and the sulfate and chloride salts of sodium, calcium and magnesium.

Jan 7, 1962

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process. This procedure can be made quantitative. Separations are obtained and are remarkably complete and repeatable. The effect of different reagents, optimum quantities, pH and other variables can be determined in a fraction of the time required for conventional testing. However, the method gives no information on the effect of frothers and the quality of froth to be expected in a cell, and it is not practical for particles finer than 200-mesh. Unlike other preliminary tests, separate float and nonfloat products are obtained, and their contents can be determined quantitatively by chemical analysis or grain counts. After the optimum reagent combination has been determined, the effect of fines and frothing may be verified in the conventional flotation cell. On the other hand, agglomeration-tabling can be directly duplicated from beaker tests. Procedure: Five to ten grams of sample are weighed into a 100-ml beaker. Flotation reagents and a small initial quantity of water are stirred together; additional water is then added to produce the proper water-solids ratio. The beaker is then tilted to 45" and rotated slowly. After three to five rotations, liquid and float are poured off and filtered; the filtrate may be recycled until the separation is completed. One test generally requires less than 10 min. Reagent concentration and pH remain quite constant because of the recycling of the filtrate. Two to four tests may be made simultaneously, and the effect of varied conditions may be observed by comparison. Considerable time is saved in preparation and handling since small quantities of sample suffice for a series of systematic tests. Repeatability One test was repeated four times under constant conditions. The sample used was a quartz sand containing approximately 24 pct feldspar and some clay aggregates. The +28-mesh grains had been screened out, and most of those finer than 100-mesh had been removed by hydraulic classification. The results are presented in Table I. For comparison, 500 g of the sample were separated by agglomeration-tabling using the same reagent combination and quantities as given in Table I. The weight percent float was 18.3 pct, composed almost entirely of feldspar and with only traces of quartz. Most of the remaining feldspar was recovered in a middling product with 2.2 pct by weight.

Jan 1, 1952