Search Documents

By C. F. Cockrell, K. K. Humphreys, H. E. Shajer

It is quite conceivable that the question of using coal or an alternate fuel in the future by large industrial consumers may be decided on the basis of possible profitable utilization of flyash. Accordingly, the Coal Research Bureau at West Virginia University has been attempting to develop new uses for this waste material. This effort has resulted in the development of a process for producing flyash-based face brick and other structural materials which generally exceed published specifications for competitive clay-based materials. These structural materials, containing up to 97% waste coal ash, can be produced from flyash derived from most coals without regard to the physical or chemical properties of the coal ash. Preliminary production cost estimates indicate that face brick can be manufactured at a rate of 9000 brick per hr or more with a resultant gross profit of over $24.00 per thousand brick. Plant payout time for a plant of this size would be only about 1.2 years assuming a market price of approximately $55.00 per thousand, a well established figure for comparable clay brick. With flyash production expected to more than double in the next 15 years, there is an increasing need for a practical and Profitable method for the utilization of large tonnages of this material (see Table I listing total flyash production of utilities in each state of the U.S.). Present industrial and governmental physical and chemical restrictions, particularly for use as a lightweight filler or pozzolanic material, have limited the use of flyash considerably. For those ashes which have met the required standards, utilization is not always assured because of lack of promotion and poor public acceptance. Less than 6% of the total flyash production in the U.S. was sold in 1962. The remainder was dumped in disposal areas at costs as high as $2.42 per ton.' It is quite conceivable that in the near future the question of using coal or an alternate fuel by large industrial consumers may be decided on the basis of the possible utilization of flyash. To help insure future coal demands, the Coal Research Bureau at

Jan 1, 1968

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.' Nickel added to the iron progressively decreases the stable range of composition of wustite.' When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs' determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. ' 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.' 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex X-ray instrument for the measurement of the ash contents of washed bituminous coal products. The results obtained for selected products from five preparation plants in the northern Appalachian region are described. Emphasis of the study was placed on low-ash bituminous coals suit-able for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by the Cendrex for all the products tested. A principal disadvantage of coal in competition with other fuels has been its inconsistent quality, especially with respect to ash content. Mine rnechanization and production from coalbeds of inferior quality have accentuated this failing. Present quality control methods in coal preparation plants are inadequate because (1) control samples taken over a production shift only serve to give the average quality of the product, (2) conventional sampling and analysis data are usually not available at the time a shipment is scheduled, and (3) the plant operator does not have the use of such data when the coal is being processed so that operating conditions may be adjusted for correcting variations in quality. Thus, the development and use of continuous-control monitoring instruments is of prime importance. The Federal Bureau of Mines arranged to investigate an instrument using x-rays for rapid continuous ash determinations. Developed by the Dutch State Mines and first described in 1958,' this instrument, which has found widespread acceptance in Europe, is designed to provide ash analysis of any desired coal feed or product stream with only a five-minute time lag between sample collection and analytical results. With limit controls, this unit could be used to feed back signals to preset the separating gravity of coal washers, control the ratio of various coals needed to produce an acceptable blend, and permit the sorting of a washed product into two qualities, one which is below and the other which is above a prescribed ash content. This unit can also be used discontinuously for rapid determination of coal samples taken in the usual manner. THEORY Di jkstra and Sieswerda of the Dutch State Mines studied the effect of chemical composition and ash content on the absorption coefficient of coal with the transmitted radiation method.' They found that with an X-ray wavelength of 1.79 A and values calculated for the absorption coefficients of ash and combustibles, the absorption coefficient of coal gave a linear relationship when plotted against the ash content. Thus, a method of measuring the absorption coefficient of coal could also be used to measure the ash content. However, practical attempts to measure the ash content of coal by comparing the intensities of the transmitted X-rays failed. The absorption coefficient of coal can also be obtained by irradiating a layer of coal with x-rays and measuring the intensity of the diffused reflection (backscatter method). The relationship between the diffused reflection and the ash content is actually hyperbolic but approximates a straight line over a narrow range. A measuring circuit that balanced the difference in intensity of the reflected radiation from a standard surface against that from a coal sample was used. By plotting this difference of reflected radiation against the ash content, a curve which approximated a straight line over a range of 8 percentage points of ash was obtained. DESCRIPTION OF EQUIPMENT The apparatus performs two distinct functions: (1) the preparation of the sample to a suitable size consist and moisture content for delivery to the x-ray element, and (2) the measurement of the ash content by the x-ray element. In a continuous operation the coal sample is delivered to a conditioner where it is dried to a maximum of 1% surface moisture and pulverized in a high speed mill to -48-mesh. This material is fed, at a rate of 250-300 gpm onto a rotating disk, shown in Fig. 1, where it is mixed with material already present. The mixture is rotated on the disk and

Jan 1, 1969

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.' I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By G. L. Wilhelm

Prior to the construction of a 450 tpd concentrator at the Mayflower mine, owned by the New Park Mining Co. and operated by the Hecla Mining Co., the common mining methods were cut and fill, with waste or gob filling and square set timbering with waste fill. Stoping operations were beset with the usual problems related to waste filling methods- storage and handling of fill material from development, costly waste excavations necessary to obtain a portion of the needed waste rock, slow mining cycles due to filling and inefficient ground support. After Hecla Mining Co.'s successful utilization of sandfill in its mines in the Coeur d'Alene district, utilization of hydraulic fill in stoping operations at the Mayflower was a logical development of the modernization plan then in progress. The mine, located in the southeasterly part of the Park City mining district, Utah, is a medium size producer of lead and zinc ores, with gold, silver and copper as secondary minerals. The mine has been producing commercial ore since 1939 from a dual vein system which outcrops at an elevation of 7200 ft in the Wasatch Range. Access to the present mining areas is gained by a 7200-ft haulage tunnel and by an interior, three-compartment main shaft. The present mining horizons are about 2400 ft deep. The average horizontal cut and fill stopes, ranging from 3-15 ft wide and up to 120 ft long, can be classed as small.

Jan 5, 1968

By D. A. Elgillani, M. C. Fuerstenau

With either sulfonate or oleate as collector, quartz responds to flotation with moderate additions of calcium only at moderately high pH, where some portion of the activator has hydrolyzed to caOH+ . Calculations of the concentrations of various ionic and precipitated species of calcium and collectors suggest that the products of [(CaOH+) (RSO3)] and [(CaOH+)(01-)] determine whether flotation is obtained under specific conditions. Ion products on the order of 10-12 were calculated for both the sulfonate and oleate systems. The activating effect of calcium ion in nonmetallic flotation systems is of considerable interest because of the normal presence of calcium in natural water. As a result, this phenomenon has received quite some attention in the past. Kraeber and Boppel1 showed that quartz could be activated by calcium above pH 10 with sulfonate as collector. The feasibility of selectively separating quartz from hematite with calcium activation at relatively high pH was demonstrated by Clemmer, Clemmons, Rampacek, Williams, and stacy.2 Cooke and Digre3 showed with a bubble pick-up method that the minimum quantity of calcium ion required as activator for complete pick-up of particles occurs at pH 11.5 for an addition of 20 mg per liter sodium oleate. They also showed that larger additions of calcium (10-fold increase per unit decrease of pH) must be added for complete bubble pick-up as the pH is reduced. Schuhmann and Prakash,4 using a vacuum flotation technique, found that quartz could be floated with moderate additions of calcium chloride and oleic acid at neutral pH, providing the metal ion was present in stoichiometric excess over the quantity needed to form the normal soap with oleic acid. They also reported that calcium will function as an activator only in basic media. More recently, Eigeles and volova5 have shown that essentially complete flotation of quartz is obtained with 6 x 10-4 mole per liter calcium chloride and 1.7 x 10-5 mole per liter sodium oleate at pH 11.6. while no flotation is obtained at about pH 10.9 and below. The importance of adsorption of activator and collector at the air-liquid interface is also demonstrated in these systems. The important role that metal ion hydrolysis assumes in quartz activation systems was also demonstrated recently.6-8 A detailed investigation of metal activation in sulfonate flotation of quartz was undertaken in one system7 and yielded a number of interesting and important observations. Quantification of the data of this system7 to the extent desired was not possible, though, because certain species could neither be ignored nor accounted for accurately. These difficulties can be circumvented when calcium is involved as activator. This detailed analysis was undertaken to obtain a more quantitative explanation of calcium and metal ion activation in quartz flotation. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate9 mol wt 450, and pure potassium oleate were used as collectors. All other reagents used were reagent grade in quality, i.e., n-amyl alcohol as frother, KOH for pH adjustment, and calcium chloride. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. The experimental equipment and procedure were the same as that described previously.6,10 EXPERIMENTAL RESULTS As the presence of precipitates was noted in all of the systems to which ca++ and collector were added, experiments were undertaken to determine the solubility products of calcium sulfonate and calcium oleate using a nephelometer. With this technique, collector is titrated into a known solution, which in this case was 5 x 10-5 mole per liter CaCl2 at pH 5.5. Upon precipitation of the calcium-col lector salt, e.g., calcium oleate, light is scattered and detected

Jan 1, 1967

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

By Edmund Newton

The steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry. has been accustomed to use. To make them available, therefore, either the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries for chemical purpose, and in other ways; while approximately 750,000 T. are required for making steel. , By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen, During the year 1917, 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T. of ferromanganese. was imported. The metallic manganese represented by these alloys was 304,000 T., the product of roughly 800,000 T. of high-grade ore and 345,000 T. of low-grade ore. Manganese Deposits in the United States Before the war manganese ore was mined in relatively small quantities in the Appalachian region, including Virginia, Tennessee and Georgia, and in Arkansas, but owing to the increase in prices during the past three years manganese mining has been undertaken also in Montana, California, Arizona, New Mexico, Nevada, Utah, and Minnesota. From data now available it appears that in this country deposits of high-grade manganese ores are usually small, while materials lower in manganese and higher in iron occur in appreciable quantities. Our total quantity of manganese-bearing material is relatively large, but on

Jan 1, 1920

By Jack Fox

Although this is going to appear in the December Issue of &E, it is being written long before the end of the year. December, of course, is the time for a summing up of the year's activities. Perhaps, the best way to begin is to report on what went on at the SME Board of Directors Meeting in St. Louis on October 20. This won't be a chronological report, and I shall take time to comment on some of the items we cover as we go along. You should be encouraged to know that your Directors take their duties seriously. Of the 21 current Directors, 19 were present, and three of the new 1971 Directors came to observe what goes on at an SME Board Meeting.

Jan 1, 1970

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of 'style'- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie's remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By J. Marshall Downey

The most fortunately situated U. S. potash producer-whether in New Mexico, California, or Utah--once simply took from the ground a mixture of sodium chloride and potassium chloride, crushed it to a maximum of 10 mesh, and separated the two salts by physical methods. He piled the sodium chloride on the desert and sold the potassium chloride to fertilizer mixing companies. Seven companies in the Carlsbad basin of New Mexico now use at least three basic processes for making the separation and at least three more processes have been or are under investigation. In addition, two companies outside the basin use two methods for taking KC1 from natural brines

Jan 12, 1958