Search Documents

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By Karl D. Libsch, Modesto E. Erneta

Both battery design and environmental pressures are forcing the secondary lead industry to consider new and different processes. Trends in battery design are making normal decasing increasingly difficult. Lead in air, sulfur dioxides, and solid/liquid waste heavy metal restrictions are tightening. There is no clearly defined industry trend toward a given process, but it is clear that plants will be larger, less labor-intensive, and automated.

Jan 1, 1977

Geology, by O. D. Von Engeln and Kenneth E. Caster, McGraw Hill Book Co., Inc., $7.00, 730 pp., 1952.The authors desired to write a book which would supplement the work of the teacher. The effort presents the facts of historical geology as an outgrowth of the understanding of physical geology-a method in keeping with the fundamental law of geology that "present agencies and forces, acting through enormous time, have shaped the world as we see it-the law of uniformitarianism." Narrative continuity is maintained throughout the text. Each historical geology period is made distinctive, provided with an identity, and shown to have particular characteristics. Elementary Heat Power, second edition, by Harry L. Solberg, Orville C. Cromer, and Albert R. Spalding. John Wiley & Sons, 1952. $6.50, 624 pp. The authors attempt to develop an understanding of the functions, principles of construction, and actual performance of heat-power machinery as a preliminary to the study of engineering thermodynamics. Matter and energy, fuels, and combustion are considered first, followed by chapters on internal combustion engines, fuel burning equipment, and steam engineering and utilizing installations. Pumps, compressors, gas turbines and refrigeration are also dealt with.

Jan 1, 1952

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.' This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

By A. C. Backeberg

There is no South African code for the design of reinforced concrete headframes, and all those erected have been designed on a uniform basis which, up to the present, has tended to be conservative. With certain exceptions designs have generally conformed with British Standard Code of Practice C.P. 114. In the design of reinforced concrete headframes the following loads are taken into account:

Jan 11, 1961

The Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysi-cists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1946

The Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysi-cists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1946

By Graham Bright

Metal mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-fame lamp was exceedingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only permitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, I;. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the development of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the developmenb was almost entirely along the

Jan 1, 1936

By Graham Bright

Metal mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-fame lamp was exceedingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only permitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, I;. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the development of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the developmenb was almost entirely along the

Jan 1, 1936

By N. J. Olson, G. W. Toop

A regular solution is characterized by a finite molar heat of mixing and entropy due only to ideal or random mixing. The thermodynamic properties of binary regular solutions which exhibit constant atomic coordination number and constant atom-atom intefac-

Jan 1, 1967

By P. V. Martin

SHORTLY after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bes-semer process stimulated a, rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracite and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt,, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast tempera-ture not only resulted in greater output but also reduced fuel consumption far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given tile chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's pains-taking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recog-nition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory.

Jan 1, 1939

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935

By Phillip B. Bucky, Fred D. Wright

The present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should Prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems, The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.' As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining Cost. It Was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1949

By C. M. Shigley

Tan record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.1 The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 t0 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000000-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation-the largest known magnesium plant utilizing sea water as its raw material. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and y miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1945

By Chung Yu Wang

During the time I was in charge of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:' "The iron ores at Tayeh * * * * lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between hornblende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende."' These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General DescriptLon of the Deposits The deposits are situated to the west of the Yangtse River, being connected with the river by a standard-gage railroad of 66 li (18.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 1, 1918

Professor Jenney has performed a notable service in presenting this summary of the steadily increasing body of observation on the presence of carbon in rocks of all kinds and its probable influence upon ore-deposition, and in formulating a mode of comparing directly the relative resistance of minerals to oxidation, as well as their reducing-power, and the protective action which minerals having higher reducing-powers exert in preventing the oxidation of associated minerals which possess relatively lower affinities for oxygen. I have had an opportunity of observing a vein which falls within the scope of his interesting discussion. The vein at Ku Shau Tzu, Mongolia, lies directly across a contact of limestone and overlying bituminous shales. Probably it occupies a compression-fissure. The shale has been reduced to such a condition of' non-coherence that much of it can be crushed in the hand, producing a handful of angular fragments resembling beech-nuts in shape and size. In the limestone the metals are principally in argentiferous galena with some pyrite and blende; but the latter two are very subordinate in quantity to the galena. In short, it is an every-day lead-vein in limestone, with siliceous limestone gangue. It is one of those veins in which the ore is not continuous, but consists of a band in the country-rock in which seams of lead sulphide begin at one wall and cross in a bent form, increasing in thickness, to the other wall, where they thin out and end. This may indicate torsional stress, but the shape of the lenses points to some other action. They often ran nearly parallel to the hanging-wall for a considerable distance and crossed the vein on a moderate angle, but turned sharply along the vein on approaching the foot-wall. The intermediate rock contains nodules, bunches and specks of ore, and the lenses vary exceedingly in size, shape and position in the vein.

Jan 1, 1903

By Robert Glass Cleland

THE DEVELOPMENT of the Phelps Dodge copper and railroad interests began in one era of the company's history and continued unbroken into the next. Yet the two eras themselves were strikingly dissimilar and represented marked differences in the company's activities, corporate structure, and personnel. From its organization in 1834 almost to the end of the first decade of the twentieth century, the partnership known as Phelps Dodge was directed, managed, and controlled by the family dynasty established by Anson Greene Phelps. The last two directing partners of this three-generation-old regime assumed control of the company's affairs in 1879 when the economic revolution that followed the Civil War was well under way.' They lived in an age of gigantic undertakings, gigantic enterprises, gigantic combinations, gi- .

Jan 1, 1952