Search Documents

By Erwin Pink

It has been pointed out in a previous publication' that, for a given strain rate, serrated yielding can be observed only at certain test temperatures. Fig. 1 shows the results obtained for polycrystalline and re-crystallized tantalum, Va group in the periodic table of elements, where serrations in the course of deformation match the decrease of total elongation. However, there was no evidence of repeated yielding when testing molybdenum or tungsten, VIa group, at similar conditions, i.e., annealed and air-cooled samples (serrations have been found in quenched tungsten2). The reason for the observed serrations in the stress-strain curve are dissolved impurities on interstitial sites of the lattice. Of importance is the concentration of oxygen, carbon, and nitrogen, which are in random solution. Two methods to calculate the limiting concentrations for serrated yielding have been evaluated and applied with more or less success in estimating the role of carbon and nitrogen in mild steel.3 J. Friedel4 has given two equations, which determine the upper and lower strain rates i for the appearance of serrations at a certain test temperature: W denotes the binding energy of the interstitial atom, -1 ev for refractory metals;5 e' the portion of continuous strain in the discontinuous stress-strain curve, measured as -3x10-3; b the Burgers vector, c the concentration, see Table 11, in atom fractions; p the dislocation density, -2 X l09 per cm2 at an average stress ?, -15 kp per mm2 at medium strain. k stands for the Boltzmann constant, T for the absolute temperature, and D for the diffusion coefficient. Table I. Eq. [1], for a given strain rate, determines the minimum temperature, and [2] the maximum temperature, below or above which no "dynamic strain-aging" can occur. According to the calculation, which uses the given quantities, serrations should only be observed within the cross-hatched temperature regions in Fig. 1, and this is in good agreement with the experiment. The effect of varying impurity concentrations is indicated schematically in Fig. 2: only Eq. [I] is affected. Setting Eq. [I] equal to [2], one can calculate the limiting concentration cmin which first causes serrations. The second method uses the aging condition by Cottrell and Bilby6,7 \£i/ \ n. a / where n(t) is the number of impurity atoms, which segregate at a dislocation line of 1 cm length after the time t (t in our case is the time between "repeated yield drops" in the serrated curve, or, the time until the above mentioned strain E' is obtained, i.e., -1 sec for medium intensity or serrations). no is the number of impurity atoms in 1 cm3 and A = Qb4ep[(1 + v)/(l - v)], derived from equations given in Ref. 7. p is the shear modulus, 18,800 kp per mm2 for tantalum, 12,200 for molybdenum, AE the tetragonal distortion caused by interstitial impurities in a bcc lattice (approximately 0.4 for both tantalum and molybdenum) and v Poisson's ratio (0.35 for tantalum, 0.30 for molybdenum). From Eq. [3], combined with the condition for a pronounced yield drop as formulated by cottrel16 (at least one impurity atom segregated at the unit length of a dislocation), again a no min, and hence the concentration Cmin can be calculated.

Jan 1, 1970

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru, for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to. appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By A. W. Furbank

IN reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65º. The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95º. Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45º relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140º. Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1938

By Freeman Bishop

The Bureau of Mines, beset by political woes not of its own making, is struggling to maintain equilibrium as Congress is being made the focal point for repeated charges that the Bureau has "not done a very good job" of setting up and supervising coal mine health and safety standards approved last year by the Congress. Senator Harrison Williams (D- N.J.) is the latest to enter the arena. A crusading legislator, he is now calling for "legislative overview" hearings to judge Bureau competency in matters of coal safety legislation enforcement

Jan 1, 1970

By Carleton Ellis

The problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific standpoint, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London ; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by may of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of

Jan 1, 1913

By Ian Wark

IN the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practiced at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts off many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies-the Broken Hill South, the North Broken Hill, and the Zinc Corporation-together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism.

Jan 1, 1932

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960

This study of engineering education arose out of the action of a joint committee on engineering education, representing the principal engineering societies. The committee had gathered so much material that it decided the work could best be carried out by some one trained in applied' science, who would devote his entire attention to the study.. The Carnegie Foundation therefore asked Prof. Charles R. Mann, of the University of Chicago, to undertake the work. After making a thorough study Prof. Mann has made a most comprehensive report. In it he says: The engineering schools of the United States began their work upon a definite teaching plan and one that had at least pedagogic consistency. But during the past half century the course of study has been overlaid with many special studies intended to enable the student to deal with the constantly growing applications of science to the industries. As a result, the load upon the student has become so heavy that there is a feeling that the students fail to gain a satisfactory grounding in the fundamental sciences and do not fulfil the expectations of engineers in d manufacturers in dealing with the practical problems with which they are confronted on leaving school. At present 60 per cent. of those who enter the schools fail to graduate, still many of them persist in engineering and make a success of it. It is evident, therefore, that the present systems of admission are not satisfactory. If a group of schools will take up the careful study of their entrance systems and experiment with objective tests and records of the students' youthful interests and achievements, the percentage of elimination can be reduced to at least a fourth of its present size, with an enormous saving of time, energy, and money for both student and school. The number of required credit hours per week should be less than eighteen, preferably sixteen. The few experiments that have been made indicate that college students do their best work when not more than five subjects are studied at a given time.

Jan 1, 1919

By Walter Lang

The year 1931 has shown a marked change over 1930 in New Mexico, with respect to the volume of activities attendant upon the petroleum industry. Although the total production of oil and gas this year exceeds that of preceding years, the results have been attained from established units operating under restriction, but capable of supplying far more than the economic conditions justify. The presidential order of March 12, 1929, that "there will be complete conservation of Government oil in this administration," has merely anticipated a normal consequence of overdevelopment. As a result of the combined economic and legal restrictions imposed, very little new drilling has occurred during the year. Even in proven areas the drilling of offsets has been curtailed to the absolute limit of requirements. Scouting and sample-cutting, which in 1930 were still in a state of feverish activity, are at low ebb, and lease buying has reached a condition of stagnation. A number of the major oil companies have either materially reduced their field and office forces or completely eliminated local office representation. Two tests of particular interest, because correlation shows them to be structurally high although they failed to produce, are the National Securities well drilled six miles west of the town of Hobbs, on sec. 33, T.18 S., R.37 E., Lea County, to a total depth of 4272 ft., which developed a flow of 4,000,000 cu. ft. of gas at 3860 ft., and a show of oil; and the Western Drilling Co. No. 1 State, sec. 16, T.20S., R.32 E., Lea County. The latter test found dead oil at 2575 to 2580 ft., and sulfur water at 2745 ft., increasing to 2780 ft., representing the zone from which production was generally expected. The well was drilled to 4013 feet. The discovery of sulfur at about 950 ft. in the deepening of an old water well (Pearson, NE. 1/4 sec. 8, T.16 S., R.25 E.) drilled in the Little Cottonwood area northwest of Artesia led the Union Sulphur Co. to drill three prospect tests on a block of acreage in the vicinity during the summer and fall. The results of the investigation have not been disclosed. The Kummbaca Oil and Gas Co. drilled the T. J. Kerline No. 1, in sec. 34, T.21 N., R.30 E., Harding County, gaging 3,654,000 cu. ft. of 98 per cent CO² at 940 ft. The Barton structure, 20 miles east of Albu-

Jan 1, 1932

By Willard H. Tracy

The method of seismic reflection prospecting has many times been compared to sound ranging, a process that became familiar to many during the World War. According to this very simple theory, the dynamite goes off and sends out a compression wave, which meets a reflecting horizon and returns to the surface, where it is recorded and the elapsed time of its travel in the earth accurately determined. Computations are then made on the general theory that the longer the elapsed time, the greater the depth of the reflecting bed. While this serves to give an idea of the fundamental basis of the process, it suggests a simplicity that does not exist in the life history of the various waves set up by a dynamite explosion in the earth. To begin with, a seismic wave in the earth does not obey the same simple laws of propagation that apply to a sound wave in the air. The property of strength in shear possessed by solids introduces a factor that sets such waves apart from the ordinary air waves. Also, the transmission charactcristics of the earth vary widely from place to place, and a fairly accurate knowledge of the space relationships of these variations is necessary if the final results are to be understood. Besides the waves recorded and used in the reflection computations, there are many

Jan 1, 1940

By Willard H. Tracy

The method of seismic reflection prospecting has many times been compared to sound ranging, a process that became familiar to many during the World War. According to this very simple theory, the dynamite goes off and sends out a compression wave, which meets a reflecting horizon and returns to the surface, where it is recorded and the elapsed time of its travel in the earth accurately determined. Computations are then made on the general theory that the longer the elapsed time, the greater the depth of the reflecting bed. While this serves to give an idea of the fundamental basis of the process, it suggests a simplicity that does not exist in the life history of the various waves set up by a dynamite explosion in the earth. To begin with, a seismic wave in the earth does not obey the same simple laws of propagation that apply to a sound wave in the air. The property of strength in shear possessed by solids introduces a factor that sets such waves apart from the ordinary air waves. Also, the transmission charactcristics of the earth vary widely from place to place, and a fairly accurate knowledge of the space relationships of these variations is necessary if the final results are to be understood. Besides the waves recorded and used in the reflection computations, there are many

Jan 1, 1940

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By R. L. Stegman, M. R. Achter

Nickel, fatigued in vacuum, shows intragranular crack initiation and growth at low temperatures. An increase in temperature initially prolongs fatigue life due to a more homogeneous distribution of slip. With a further temperature increase, the mode of failure undergoes a transitiotz to intergranular crack initiation with concurrent recrystallization which results in a shorter life. The transition temperature varies with bending strain and specimen purity. UNTIL recently, very little work has been done on the effect of temperature on the mechanism of fatigue and the resultant variation in fatigue life. Except for mild steel, where strain aging raises the strength at moderate temperature, fatigue lives had been shown to decrease with an increase in temperature. In their review article, Allen and Forrest' summarized the work of McCammon and Rosenberg and of Forrest and Mann on the fatigue of copper from -269" to 325°C. The fatigue life vs stress curves remained roughly parallel over this temperature range, the fatigue strength decreasing progressively with increasing temperature. When testing was done in vacuum, the present authors' found the results for nickel were different from those quoted above. Initially, the fatigue lives increased with temperature and then decreased as a grain boundary mode of failure was observed. The initial increase was attributed to a more homogeneous distribution of slip, a condition which was not as conducive to crack initiation as the bunching of slip lines observed at 20°C. Ronay, Reimann, and wood3 observed a similar change of slip line distribution in brass, tested in air, with rising temperature. Our previous observations were based on preliminary work with relatively few specimens, fatigued at comparatively low strains. To learn more about the mechanisms, the present investigation was undertaken for the purpose of studying systematically this effect over a wider range of strains and as a function of purity of the nickel. EXPERIMENTAL PROCEDURES The testing equipment, procedures, and specimen geometry have been described elsewhere.' An optical technique to measure bending strains was used as de-

Jan 1, 1968

By H. Herman, M. E. Fine

Kinetics of reversion and reformation of GP I were studied resistometrically in Al-1.7 at. pct Cu. The reversion process is over in roughly 1/2 minute at 205 "C irrespective of the amount of primary aging. After reversion the occurrence of an incubation time before reaging begins has been substantiated. The reaging kinetics is drastically accelerated by plastic deformation to the specimen. An incubation time is observed only if the specimen is aged before reversion. The incubation time and the effect of plastic deformation indicate that nucleation of GP I is heterogeneous. Simple clusters of copper atoms apparently do not act as nuclei for GP I. AFTER quenching aluminum-rich copper from the solid solution range, Guinier-Preston zones of the first kind, GP I, form very rapidly at room temperature. The rate, largely controlled by the concentration of vacancies, is initially most rapid1 (that is, at the time of the first measurement: 1/2 min) and decreases with time. The nucleation is thought to be athermal. If after aging for several days the GP I is dissolved by reversion at 205°C, according to measurement of Young's modulus an incubation period is observed before GP I begins to form on subsequent aging.2 Yet if the reversion is carried out immediately after quenching, both resistivity3 and modulus changes2 show no incubation effect. The zones which form after reversion have the same structure as those which form after the quench.4 Because of entropy considerations and also the short diffusion time, the solid solution after reversion, 2 min at 205°C, is probably more highly clustered than at the original solution treating temperature, 520" to 550°C. It appears most reasonable to associate with nucleation the incubation time observed on reaging after reversion. A simple cluster of copper atoms, many of which are presumed to be present after reversion, is then not a sufficient nucleus for GP I; a GP I nucleus must contain something in addition to a cluster of copper atoms. The purpose of the present note is to give some additional experimental information concerning the incubation time and rates of reaging after reversion. The existence of the incubation time has been verified by measurement of another property, the electrical resistivity. Acceleration of reaging after reversion by plastic deformation has also been investigated. In acl.dition, the kinetics of the reversion process itself was studied. EXPERIMENTAL Electrical resistance was measured by the poten-tiometric four probe method. The 1.7 at. pct Cu alloy was furnished by the Aluminum Co. of America in the form of 1/2 in. rod. The major impurities reported by Alcoa were Fe (0.002 wt pct), Si (0.003 wt pct), and Mg (0.001 wt pct). Specimens for measuremenl of resistance were prepared by rolling to 0.010 in., cutting 2 by 0.2 in. pieces, rolling the middle pclrtions of these to 0.005 in., and splitting the 0.010 in. sections up to the reduced central section to form current and potential leads. Aluminum extension wires insulated with ceramic tubes were spot welded to the leads. The specimen was supported by the lead wires. The whole specimen assembly was annealed at 500" C in an air furnace for more than 12 hr and then aged at room temperature. This was done to assure quick and complete resolution during subsequent solution treatments. These were carried out in Houghton's "430 Temper Salt" at 520'C for 1 hr. Unless otherwise specified, quenching was accomplished by quickly transferring the specimen from a salt pot to 25°C water. Aging was carried out in a 3 liter dewar of distilled water, rotated and stirred. The temperature was controlled to +0.01°C with a thermomercurial regulator in conjunction with a transistorized relay

Jan 1, 1962

By O. C. Wheeler

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February of those two years, but the manuscripts were held until released for publication in 1945. 1942 Lack of transportation facilities during 1942 resulted in a sharp curtailment of producing operations in Colombia at the middle of the year, and production of crude for export was thus greatly affected. Total production in 1942 amounted to only 10,617,008 bbl. Of this amount the Tropical Oil Co. produced 9,453,995 bbl., which includes 126,607 bbl. of petroleum condensate, and the Colombian Petroleum Co. produced 1,163,013 bbl, from its Barco property. The following summary, showing a comparison of the number of barrels of crude produced during the years 1941 . and 1942, reflects the extent to which producing operations were reduced during 1942: These above figures do not include any production recovered from Condor's (Shell's) Casabe wells during testing operations. An active exploratory drilling Program was carried out by several of the major companies, and the year 1942 established a record for wildcatting activity in Colombia. Excluding development operations on the Shell's Casabe wells on the Yondo concession, 13 wildcats were completed. Eight of these were in the Magdalena Valley, and all were abandoned; five were on the Barco Concession, and of these four were completed as producers. Particularly notable among the petroleum developments during 1942 was the continued success of drilling operations on the Shell's Yondo Concession of Compania Colombiana de Petroleos El Condor opposite Barranca-Bermeja. In 1941 the discovery well, Casabe No. I, was drilled and completed with an estimated initial production of approximately 480 bbl. of 19 1/2 A.P.I. gr. oil per day. In 1942, seven stepouts from the discovery well were successfully completed with initial production ratings ranging from 150 to 1230 bbl. per day. An extensive wildcat program on the Barco Concession of the Colombian Petroleum Co. yielded favorable results with the completion of four producers in the Socuavo and Tres Bocas areas; a fifth test, Sardinata Norte No. I, was abandoned at 500;" feet. Wildcatting operations in the lower Magdalena Valley area were initiated in 1942 With the drilling of a deep test, El Dote No. I, by Compania de petroleo Shell de Colombia. The well was a failure and was abandoned at a depth of 10,046 (?) feet. Wildcats on which drilling operations were being conducted at the end of the

Jan 1, 1945

By Raymond S. Weimer

OF the several characteristics of a coal that influence its suitability for use in a given piece of burning equipment, the clinkering and slagging characteristics of the ash of the coal are highly important. They determine the maximum rate at which the coal may be burned on a stoker or in pulverized form without difficulty from damage to metal parts, from erosion of refractory walls, or from stoppage of gas passages by accumulation on the tubes. They also determine the minimum rate at which a slag-tap furnace may be operated without difficulty in removal of the ash in fluid form. NEED FOR A BETTER CRITERION In common with other producers and users of coal, the Northern Illinois Coal Corporation has long used the available methods for the measurement of the clinkering characteristics of coal ash, chemical composition and fusion temperature of the ash, as criteria for the selection of coal that would suit the particular requirements of its customers. These two available criteria have greatly helped in the problem of selection but it is unnecessary to dwell upon the fact that they are not completely adequate for the purpose. The composition of the ash and its clinkering tendency vary widely over the company's mining area. In a certain period, some years ago, an unusual amount of severe clinkering of the ash of coal shipped made extremely acute the need for a better criterion of the clinkering that might be expected. It was also desirable that the criterion result from a reasonably rapid method, so that the clinkering characteristics of the coal would be known before shipment. Complaints on the severe clinkering of the ash came from only a fraction of the output of the mine but the occurrence of the clinkering seemed quite unpredictable. Attempts to relate the chemical composition of the ash and the fusion temperatures to the clinkering were unsuccessful. Coal from the area of the mine in which the fusion temperature of the ash was the lowest gave the least trouble from clinkering. Chemical analysis of the ash from that section giving the most trouble showed high contents of iron and low contents of silica, but frequently these were not greatly different from those of coals that gave little trouble from clinker. Aside from the clinkering difficulty, the coal was quite satisfactory. The ash content was normal and high rates of burning could be obtained, but again and again such severe clinkering would occur that the furnace would be shut down because of the accumulation of clinker. Examination of the clinker from the customers' plants showed that the clinkers that adhered to the grates and fouled the fuel beds were hard, flat, dense, and usually dark in color. Coal that was satisfactory gave clinkers that were softer, bulky rather than flat, of low density, and usually lighter in color.

Jan 1, 1944

By John Birkinbine

In a former paper* attention was directed to the various forms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal fnrnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillatinig engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter

Jan 1, 1879

By R. W. Ludt, C. C. DeWitt

The use of froth flotation for the separation of minerals has become one of the most important of ore dressing processes. Its particular adaptability to the enrichment of low grade ores has made the process an important factor in the national economy. The methods have been extended to the recovery of a great number of minerals. Among the few minerals which have resisted efforts toward industrial flotation is chrysocolla, a hydrated partly colloidal copper silicate. Chrysocolla, being a product of natural oxidation, has been found to occur in small quantities with many ores which are recovered by flotation methods. In present practice, these small quantities of copper silicate pass off with the tailings and are lost. The advantages to be gained by a satisfactory process for the recovery of chrysocolla is apparent. Any application of principles which points a way toward the satisfactory industrial flotation process for copper silicate would be of advantage. This paper presents an attack on this problem. Two methods for the recovery of chrysocolla have been developed by the United States Bureau of Mines.1,2 They have been successful on a laboratory scale but have been seriously restricted in industrial application by critical requirements in the procedure. In one of the Bureau of Mines methods,' the ore is activated with sodium or hydrogen sulphide in an aqueous solution at a pH of 4. Amy1 xanthate is then used as a collector with pine oil as a frother in the flotation process. An excess of sulphide acts as a depressant and the state of optimum conditions is difficult to control industrially. In the second Bureau of Mines method,2 soap is used as the collector at a pH of between 8 and 9. The diffi- culties with this process are that soap is not a specific collector, that heavy metal or alkaline earth ions cause the formation of insoluble soaps, and that a more acid solution causes the formation of a free acid which does not act as a collector for chrysocolla. The problem of recovering chrysocolla by flotation involves the selection of a suitable collector. The collector molecule must be composed of an active polar group that has an attraction for chrysocolla, and of a hydrocarbon chain. Certain dyes have been shown to have an attraction for certain minerals. Suida3 found that hydrated silicates are colored by basic dyes. Dittler4 showed that chrysocolla, among other colloidal minerals of acid reaction, preferentially takes up such basic dyes as fuchsin B, methylene blue, and methyl green. Endell5 gave information to show that the colloidal material in clay may be determined by its selective adsorption of fuchsin. A simple experiment, likewise, illustrates the difference in the adsorptive power of chrysocolla and of silica for the basic triphenyl methane dyes. When a mixture of chrysocolla and silica is immersed in a very dilute dye solution, less than 5 ppm, the chryso-colla is rapidly dyed and the silica is dyed more slowly. The difference is substantial but one of degree. Dean2 showed that the dyes, crystal violet and toluidine blue, are taken up by quartz in an adsorption type process. The difference in the adsorptive power, however, offers the means by which a new collector may act. To form such a collector, a hydrocarbon chain must be attached to the dye molecule. This involves a process of organic synthesis. Butyl, hexyl, and octyl hydrocarbon chains were selected for substitution in the malachite green molecule. For the purpose of identification, the alkyl-substituted dyes formed are called: butyl-malachite green; hexyl- malachite green; and octyl-malachite green. An outline of the procedure for their synthesis is given in the appendix. It is generally recognized in the preparation of this type of dye that the chemical structure of some of the dye molecules varies. However, a uniform formula is attributed to the dye. Such a procedure has been followed in specifying the structure of these alkyl-substi-tuted malachite green dyes. The structure is given on the basis of their properties as an homologous series of dyes, on their method of preparation, and on the purity of intermediates used. Structure of substituted alkyl malachite green is: C6H4 N(CH3)2 p-R C6H4 CH C6H4 N(CH)2 Procedure The flotation cell is a Bureau of Mines 100-g, batch unit provided with an air inlet at the bottom above which is a variable speed agitator. The agi-

Jan 1, 1950