Search Documents

By R. Hogg

INTRODUCTION The principal applications of the flocculation process in the coal industry lie in the area of waste water treatment. Consequently, the concern is more with the behavior of the associated minerals, clays for example, than with the coal itself. At the same time, however, the presence of even small amounts of fine coal can significantly influence the performance of the flocculation operation. Coal preparation waste water treatment is a substantial problem involving over 200 billion gallons of water annually. There can be no doubt that these quantities will continue to increase as coal production increases and environmental considerations dictate the increased use of closed circuit systems and tighter control of effluent quality. Furthermore, we can expect to find a continued increase in the amount of fines generated in the coal mining and processing operations. Modern mining techniques tend to yield a finer raw coal with a higher ash content. The greater emphasis on fine coal cleaning for improved sulfur and ash removal and increased coal recovery will also lead to greater demands being placed upon the wastewater treatment system. The costs of "blackwater" treatment have been shown to vary widely from plant to plant (1). Part of this variation can be attributed to differences in the coal being mined and the plant flowsheet but there are no doubt significant contributions from the improper design and operation of treatment facilities.

Jan 1, 1980

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By Willard P. Ward

IT is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

Jan 1, 1876

By E. M. Kalar, I. Iwasaki, J. D. Zetterstrom

Several methods of removing fatty acid coatings from iron ore flotation concentrates were tested both on a Mesabi oxidized iron ore and on a magnetic taconite concentrate, and their effects on the duplex flotation process and on pelletizing were compared. Either acid or alkali alone could not remove the coatings, but a combination of such reagents as lime and quebracho, calcium chloride and pyrophosphate, or sulfuric acid and an organic acid (oxalic, malonic, or citric acid) was quite effective. The use of activated carbon was found to be particularly promising. The removal of fatty acid coatings from iron ores is of much practical interest when a pelletizing process is being considered for a concentrate floated with a fatty acid collector or when a duplex flotation process is being considered for upgrading an oxidized iron ore. A duplex flotation process is a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process is being used in the Florida phosphate fields.&apos; Although in northern Michigan mills fatty acid flotation concentrates have been pelletized successfully, at other locations fatty acid coatings on iron flotation concentrates have proved so undesirable in the agglomeration operation that other methods of concentration had to be sought.&apos; Since fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates, a combination of reagents, such as lime and quebracho,3 lime and alkali phosphate,4 or sulfuric acid and oxalic acid,&apos; has been proposed. It was also thought that activated carbon might be effective in removing fatty acid coatings due to its high adsorptive capacity. Activated carbon, with its enormous surface per unit of volume, is well known for its exceptional efficiency in removing organic pollutants from industrial effluents. This article presents the practical aspects of the above methods when they are applied to the duplex flotation process and to the pelletizing of iron flotation concentrates. The article also includes a preliminary investigation of the common parameters involved in the depressant activity of the reagents. EXPERIMENTAL WORK Initially, the experimental work was directed towards the optimization of each method for the removal of hydrophobic coatings from iron oxide surfaces floated with fatty acids. Subsequently, the methods thus optimized were tested in the duplex flotation process with an oxidized iron ore and in the pelletizing process with a magnetic taconite concentrate. Preliminary Flotation Tests: Although the three types of chemical treatment reported in the literature were briefly investigated for the purpose of comparison, major emphasis was placed during the preliminary flotation tests on the use of activated carbon because it was thought to have certain advantages over the chemical methods. LIME AND QUEBRACHO - To obtain a flotation concentrate for optimizing the lime and quebracho method of fatty acid removal, the magnetic taconite concentrate was used. The concentrate had a size consist of 90% passing 325 mesh and analyzed 64.5% iron. After a few preliminary tests the fatty acid flotation procedure with the magnetic taconite concentrate was standardized as follows. A 1200-g sample of the magnetic concentrate was pulped in a Fagergren laboratoy flotation cell to 40% solids, conditioned with 0.5 lb of soda ash per ton for 2 min, and then further conditioned with 1.0 lb of Acintol FA-2 per ton for 2 min. After 5 min of flotation, recovery was nearly complete, averaging 98.6% of the weight and 98.7% of the iron. The cell product, which amounted to 1.4% by weight and analyzed 63.2% iron, consisted mainly of relatively coarse middling particles. Since the repro-ducibility of the flotation concentrates produced by this procedure was vey high, the same procedure was used to prepare fatty acid concentrates for each of the six tests of the lime and quebracho method. To test the removal of the fatty acid from the magnetite surfaces by the lime and quebracho method, a fatty acid froth product was returned to the flotation cell, repulped by 30 sec of agitation, and then con-

Jan 1, 1968

The Year Book of the Institute is mailed with this Bulletin. Its membership lists, both alphabetic and geographic, are corrected to Jan. 1, 1918, but its list of officers is revised inn accordance with the elections in February, 1918. The amendment to the Constitution, relating, to qualifications for membership, adopted at the same time, is also inserted in its proper place. We would call attention to the Honor Roll, heading the list of membership. This includes the names of those whom we know (in February, 1918) to be on active military duty, as well as those who are rendering emergency service to the Government in other branches. We are aware that the list is not complete, and shall be grateful for information as to any omissions or corrections. Because of the rapid movement of the military members, their addresses have been omitted from the alphabetic list. Mail addressed to such members, and sent to the office of the Institute, will be forwarded to the best of our information at the time.

Jan 3, 1918

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

By H. B. Kinnear

THE first copper stool used under an ingot mold to receive molten steel has recently been taken out of service after it had received ingots amounting to 6012 gross tons. This stool, weighing 8330 lb. had been in continuous service for 1822 heats since its installation. From this modest beginning the use of copper for ingot-mold stools grew to 425,000 lb. in 1934, with an additional 50,000 lb. of copper used in the form of inserts in cast-iron stools. During 1935 the quantity of copper used for stools increased by about 350,000 lb., making a total of 775,000 lb. now in use for that purpose. Copper used for inserts has increased during this time 180,000 lb., or over 350 per cent, to a total of 230,000 lb. The total of copper, therefore, in use at present under ingot molds is slightly over 1.000,000 lb.

Jan 1, 1936

By S. LeFevre

THE solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covers briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results.

Jan 2, 1915

By R. E. Somers

THE Appalachian field is notable for four tests drilled in recent years to depths of over 7000 ft. and for one commercial gas well at 6822 ft. The latter is the Ligonier well and produces from the Oriskany FIG. I.-NATURAL GAS PRODUCTION OF PENNSYLVANIA AND WEST VIRGINIA. sandstone. Together with several other comparatively deep tests, these holes were drilled in search of natural gas, to make up for the decline in production of the field. The production curve of Pennsylvania FIG. 2.-EAST WEST SECTION OF APPALACHIAN FIELD. (AFTER ASHLEY AND ROBINSON, PENN. G. S.) and West Virginia from 1907-21 is given in Fig. 1 to illustrate the heavy decline from the peak of 1917. This diminishing supply has also been shown by Moyer,1 on the basis of decreasing rock pressures.

Jan 3, 1924

By K. E. Brown, A. R. Hagedorn

A 1,500-ft experimental well was used to study the pressure gradients occurring during continuous, vertical, two-phase flow through 1-in., 1 1/4-in. and 1 1/3-in. nominal size tubing. The test well was equipped with two gas-lijt valves and four Mathak electronic pressure transmitters as well as with instruments to measure the liquid production rate, air injection rate, temperatures and surface pressures. Tests were conducted for widely varying liquid flow, rates, gas-liquid ratios and liquid viscosities. From these data, an accucrate pressure-depth traverse was construcred for each test in each of the three tubing sizes. From the results of these tests, correlations have beer] developed which allow the accurate prediction of flowing pressure gradients for a wide variety of tubing sizes, flow conditions, and liquid properties. Also. the correlations and equations which are developed satisfy the necessary condition that they reduce to the relationships approprate to single-phase flow when the flow rate of either the gas or the liqutid phase becomes zero. All the correlations involve only dimensionless groups. which is a condition usually Sought for in similarity analysis but not always achieved. The correlations developed in this study have been used to calculate pressure gradients for pipes of larger diameter than those upon which the correlations are based. Comparisons of these calcuclaed gradients with experimetally determined gradients for the same flow conditions obtained from the literature indicate that extrapolation to these larger pipe sizes is possible with a degree of accuracy sufficient for engineering calculations. The extent of this extrapolation can only he determined with additional data from larger pipe diameters. INTRODUCTION The accurate prediction of the pressure drop expected to occur during the multiphase flow of fluids in the flow string of a well is a wideiy recognized problem in the petroleum industry. The problem has been brought even more into prominence with the advent of tubingless or slim-hole completions which use small-diameter tubing. Many of the correlations which give reasonably accurale results in the lager tubing sizes are greatly in error when applied to small-diameter conduits. Small-diameter conduits are defined as 1 1/2-in. nominal size tubing or smaller. The study of the pressure gradients which occur during multiphase flow of fluids in pipes is exceedingly complex because of the large number of variables involved. Further difficulties relate to the possibility of numerous flow regimes of widely varying geometry and mechanism and the instabilities of the fluid interfaces involved. Consequently, a solution to the problem by the approach normally used in classical fluid dynamics based on the formulation and solution of the Navier-Stokes equation has not been forthcoming. This is primarily the result of the nonlincarities involved and the difficulty of adequately describing the boundary conditions. As a result of the foregoing, most investigators have chosen semi-empirical or purely empirical approaches in an efford to obtain a practical solution to the problem. Much of the previous work in this area was done in short-tube models in the laboratory. A number of problems arise, however, when attempts are made to extrapolate these laboratory results to oilfield conditions where a much longer tube is encountered. In those few studies where data taken in long tubes were utilized, the data covered only a limited range of the variables, and as a result inaccuracies are introduced when the correlations are extended outside the range of the original data. Also, as a consequence of the limited amount of data available for these studies, the effects of several important variables were overlooked. The problem of predicting the pressure drop which occurs in multiphase flow differs from that of single-phase flow in that another source of pressure loss is introduced, namely, those pressure losses arising from slippage between the phases. This slippage is a result of the difference between the integrated average linear velocities of the two phases, which in turn is due to the physical properties of the fluids involved. In contrast to single-phase flow. the pressure losses in multiphase flow do not always increase with a decrease in the size of the conduit or an increase in production rate. This is attributed to the presence of the gas phase which tends to slip by the liquid phase without actually contributing to its lift. Many investigators have attempted to correlate both the slippage losses and the friction losses by means of a single energy-loss factor analogous to the one used in the single-phase flow problem. In an approach of this type, hourever, many of the important variables, such as

Jan 1, 1966

By Hubert D. Keiser

An observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. Historical Summary It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the. impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man&apos;s action was a glass fiber. Artisans in glass, throughout the long Direc- of glassmaking as an art> drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1948

By Hubert D. Keiser

An observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. Historical Summary It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the. impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man&apos;s action was a glass fiber. Artisans in glass, throughout the long Direc- of glassmaking as an art> drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1948

By James L. Poole

INTRODUCTION Companies in the mining industry are subjected at times to currency exchange rate risks and interest rate risks. The former occurs any time a firm deals in more than one currency. The latter occurs anytime a firm is financing itself with borrowings that have a floating interest rate (although a fixed rate can be a problem at times). FOREIGN EXCHANGE RISKS There are two general reasons why exchange rate risks (FX risk) can occur: First, a firm may be building a mine or plant in another country where financing for the plan is denominated in funds other than the country hosting the plant. For example, if a Canadian firm is building a smelter in another country which is being financed with Canadian dollars, the C$100 million for labor, which must be paid in the local currency, has subjected the firm to a C$100 million FX exposure risk. If after the cost estimates were made the local currency appreciates 30% against the Canadian dollar, the cost of labor has increased to C$130 million. (Of course, the local currency could also devalue during this period making the labor cost component less than estimated.) The other reason exchange rate risk arises is due to the fact that the costs of production in one country producing minerals may be incurred in one currency while the production is sold in another currency, such as coal being exported from Canada to Japan under contracts denominated in Yen. In this example, the Canadian firm is exporting coal to Japan and being paid in yen in 30 days at a contract price of 100 Y per ton. Furthermore, assume that the mining firm anticipates a depreciation of the yen against the Canadian dollar of 5% in the next 30 days. Therefore, the mining firm stands to lose 5% of the value of its shipment in a month&apos;s time not including carrying costs. In both cases, the mining company risks an adverse change in the exchange rate, that is, the currency the company holds may decrease in value relative to the other currency. There are a number of ways to mitigate the exposure to foreign exchange which can be utilized by the mining company. Optimally, a company should try to match all their inflows and all their outflows in the same currency. For example, if a Canadian firm has mining costs and debt service costs both denominated in Canadian dollars then 100% of their receipts would need to be in Canadian dollars. If a Canadian firm has 70% of its cash outflows in Canadian dollars and 30% of its cash outflow in American dollars in the form of a loan amortization then their receipts would need to be 70% in Canadian dollars and 30% in U.S. dollars. This general principle of matching cash receipts and cash costs in the same currency works fine in a perfect world but what of the real world when these cannot be matched? In actual practice, however, the financial markets have developed a number of ways in which foreign exchange risks can he managed or reduced. FORWARD MARKETS One method is to use the forward markets which are made on a world-wide basis by the commerical banks for foreign exchange. If a firm wanted to lock in the current exchange rate for the receipt of a foreign currency at some point in the future, they could do so by contracting on the forward market with a bank selling that foreign currency at the current rate at the future date. For example, assume that a Canadian firm is exporting coal to Japan which would pay yen in 90 days. If a firm wanted to lock in today&apos;s exchange rate they could contract with a bank to sell on the forward market yen in 90 days. When the yen was received the contract would be executed by selling the yen to the bank and receiving the previously agreed upon number of Canadian dollars. Generally speaking, the forward market can be used to sell forward about 12 months. The costs of selling (or buying) forward

Jan 1, 1985

By S. F. Emmons

THE first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre, in May, 1871. It is entitled The Geological Distribution of Mining Districts in the United States, and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from .a geological stand-point. At the request of Dr. Raymond, I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such published data within my reach as bore upon this subject, and could be consulted in the brief time I have been able to give to it. Had the geological investigations undertaken by the Tenth Census been continued systematically by the United States Geological Survey or by the Eleventh Census, it might have been possible to make a fairly-complete review of the subject. As it is, the principal result of my examination 1 has been to show how very unequal

Jan 1, 1913

By Howland Bancroft

This article is not presented as a treatise on tin mines and mining in Bolivia. It deals primarily with the tin situation, and but fragmentary information is given regarding individual properties, generalizations being necessary in so short an article. Data on general subjects related to tin mining in Bolivia are necessarily abbreviated and very incomplete. It is believed that the references to be found in this article will help those interested to a more thorough understanding of the general conditions extant in Bolivia. Bolivia produces from one-fifth to one-fourth of the world&apos;s supply of tin. The United States consumes about one-half of the world&apos;s supply and produces practically none. Tin ore is not reduced in the United States. These facts are not generally appreciated by American mining men. Many conflicting data have been published regarding tin in Bolivia. The Transactions of the Institute contain practically no mention of this subject.&apos; I have made a study of mines and mining conditions in the west coast republics of South America and have been particularly impressed by the possibilities of the Bolivian field.= In consequence the thought seems justified that the present meeting would present a fitting occasion to bring the tin situation in Bolivia to the attention of American mining men.

Jan 1, 1914

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939