Search Documents

By C. E. Sims, F. W. Boulger, H. A. Saller

Most of the data on equilibrium constant and the deoxidations potentialities of those elements, considered to be stronger deoxidizers for steel than is silicon, have been calculated from thermodynamic data. The reason for this is, primarily, the obvious difficulty of obtaining direct experimental evidence of equivalent accuracy. This is an excellent use of the principles of thermodynamics and has given valuable data not otherwise available. Such results, of course, can be no more accurate than the physical constants used in the calculations, and one can never be sure that the basic data are either complete or accurate. In fact, as in the case with silicon,1 there are not only discrepancies among the calculated theoretical values of the equilibrium constant for deoxidation of steel but also between the theoretical and experimental values. It is highly desirable, therefore, to obtain experimental values for checks on calculated results whenever possible. If they disagree, both cannot be right, but if there is good agreement, their value is enhanced. The present work was done in an effort to obtain experimental evidence in regard to some of the common alloying additions but more particularly the so-called "strong" deoxidizers for steel. The method used was to determine the minimum concentration of the deoxidizer that would effect a certain definite degree of deoxidation in steel. The criterion of deoxidation was the change from the large globular Type I sulphide to the eutectic Type II as described by Sims and Dahle.2 This change is sharp and definite, and inasmuch as it can be produced with equal facility by aluminum, zirconium, and titanium, it is considered a manifestation of a certain degree of deoxidation and not an alloying effect. Ostensibly such a procedure could give only a comparison of deoxidizing powers and no absolute values. Nevertheless, repeated observations have shown that, when increasing increments of aluminum are added to a steel, the residual aluminum content begins to increase simultaneously with the appearance of Type II inclusions. Thus it seems warranted to postulate that the Type II inclusions appear coincident with the virtual elimination of FeO as an active constituent of the steel. Experimental Procedure The data obtained were primarily from the microexamination of polished and unetched specimens and from chemical analysis. Experimental heats weighing 200 to 250 lb were made in a basic-lined high-frequency induction furnace. The base composition was nominally that of a medium-carbon casting steel to which the appropriate additions were made. Specimens were poured into sand-cast ingots 3 in. in diam as shown in Fig 1. Sand-cast ingots were used to prevent chilling and to allow sufficient time in freezing for normal inclusions to form of a size large enough to be studied readily. In the first few heats, the tapered wall ingot was used, but in the majority, the extra large riser was used to prevent piping in heavily deoxidized steels. Specimens for microexamination were taken from the location shown in Fig 1, and drillings for chemical analysis were taken from a similar location. The procedure was to melt the base composition and deoxidize with the usual manganese and silicon additions and then to pour an ingot. The furnace was then tilted back, and the first increment of strong deoxidizer or special alloy was added and allowed to disseminate through the melt, with enough power on to hold the temperature constant, for 45 sec. Then a second ingot was poured. After this, another increment was added, and after the same holding time another ingot was poured. In this way from 9 to 12 ingots were poured from each heat, each successive ingot having progressively larger total additions of alloy. Eighteen heats were made altogether, and the range of alloys used and additions made are outlined in Table 1. The three principal types of sulphide inclusions found are illustrated in Fig 2. The globular Type I sulphides are characteristic of silicon-killed steels, the eutectic Type II are characteristic of steels deoxidized with a small amount of aluminum, while the larger, angular Type III are usually found in steels with a residual aluminum content above about 0.02 pct. In all specimens studied, the transition from Type I to II either did not occur at all or was very abrupt and clear cut. There never was any doubt as to just which increment produced the change, although the individual additions were small, in the order of 0.01 pct. The change from Type II to Type III was considerably less sharp, and, in some cases, both types were found together. Inasmuch as the formation of Type III sulphides is apparently not a deoxidation phenomenon, they will not be discussed here.

Jan 1, 1950

By H. M. Callaway

There are key words common to Government and the minerals industry, the use of which immediately spark interest, argument and confusion. Among these is productivity, a term ranking for widespread misunderstanding with mineral self-sufficiency and mineral conservation. Each interpretation of these words tends to emphasize a single aspect and either minimize or ignore the complex dynamic system of things that influence the Nations mineral productiveness. This paper1, abstracted from a monograph on lead now being prepared for publication by the Bureau of Mines, not only sheds light on the trend of productivity in the lead-zinc mining industry but it presents the basis for forming a common general notion of what the term productivity implies.

Jan 11, 1961

By Oscar M. Wicken

The mineral magnesite (MgCO3) if pure would consist of 47.7 pct MgO and 52.3 pct CO2. It is one of the calcite group of rhombohedral carbonates which includes calcite (CaCO3), siderite (FeCO3), rhodocrosite (MnCO3), and smithsonite (ZnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions, whose range is still imperfectly known.* MgCO3 and FeCO3 appear to form a complete series of which breunnerite (ferroan magnesite) is a well known variety. Because of the considerable difference in size of the Ca and Mg ions, there is only a limited range in substitution in the MgCO3-CaCO3 series. (Dolomite, not strictly a member of the calcite group, may be regarded as an ordered structure developed when Ca: Mg is approximately 1:1.) The practical consequence of these relationships is that the lime carbonates (calcite and dolomite) are commonly present in magnesite deposits chiefly as mechanical mixtures. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black through shades of yellow, blue, red or gray. It is rarely found pure but generally contains variable amounts of iron, lime, and silicate minerals. Color cannot be used as an index of purity except under specific local conditions in a single quarry. In a given quarry an experienced man may be able roughly to grade magnesite by intuitively assessing such features as crystallinity and color. Crystalline magnesite occurs in larger deposits, but the cryptocrystalline variety is more common. The latter is fine-grained and compact and shows no cleavage; often it is descriptively called "bone magnesite." The fracture is usually conchoidal, and hardness is 3.5 to 5.0. It is normally white, but sometimes it is light yellow to orange or buff because of included impurities. In addition to lime and iron, which may be present in small amounts, silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. In general, commercial deposits of "amorphous" magnesite have lesser amounts of accessory minerals than does crystalline magnesite. The specific gravity of "amorphous" magnesite is 2.90 to 3.0. Pure, crystalline magnesite has a specific gravity of 3.02, but iron carbonate, commonly present, raises the specific gravity to somewhat higher values. Magnesite dissociates, when sufficiently heated, into magnesia (MgO) and carbon dioxide. Either simultaneously or upon further heating the magnesia develops a crystalline structure identical with that of the natural mineral, periclase, which occurs sparingly in nature but not normally in workable deposits. Brucite is another magnesium mineral capable of being directly reduced to magnesia by heat alone. Brucite (Mg(OH)2) has been mined for the production of various grades of magnesia. It theoretically contains 69.1 pct MgO and 30.9 pct H2O. It may be white, but is generally blue or green with a gray cast. It has a translucent appearance. The mineral is soft (hardness, 2.5), and has a specific gravity of about 2.4. Nomenclature of Products The word "magnesite" literally refers to the natural mineral, but common usage has applied it plus a prefatory word to two other

Jan 1, 1960

By Maximo Monte-Flores

A PERUSAL of the most recent literature on the subject of hydrocarbons reveals that one point seems, to have been neglected by the various theories; that is, the influence of the bed-rock on the accumulation and distribution of oil and gas. This can be seen from the following statement of the principles of the most accepted theories. ANTICLINAL THEORY The anticlinal theory claims that the accumulation of the hydro-carbons in deposits of commercial importance was brought about by the gravity of the hydrocarbons, the oil and gas being forced to the top of the porous stratum by the difference of the specific gravity of the hydro-carbons and the water. The principal factors toward the accumulation were the general stratigraphic condition of the rocks, their texture and porosity, and their water content. This theory advocated the preexistence of structural deformation as the basis of the motion of gravity, thus implying the principle that the forces that have caused the deformation have had no influence on the movement of the hydrocarbons. STRUCTURAL THEORY According to the structural theory, the accumulation is due, chiefly, to the structure of the subsurface rocks and differs from the anticlinal theory, mainly, in not considering that the motion of the liquids have been caused by the force of gravity.

Jan 1, 1920

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By Niles E. Grosvenor

Complex underground mining problems are increasing as mining depths increase. Many of these problems have been solved mainly by unsystematized trial-and-error methods based on individual experiences. This system of solving mining problems has resulted in over-cautiousness whereby a large quantity of our mineral resources are left in the ground, or not enough caution with a resultant failure of the underground opening. From studies made of physical properties of rocks, large volumes of data have been collected as a source of finding correlation among the different physical tests or among certain rock types. Most of these studies have not produced satisfactory results because the investigator usually arrives at the conclusion that the results are too scattered to be reliable. The reasons usually given as the cause of this scatter are that rocks are nonhomogenous and non-isotropic. Similar types of poor correlation that were being obtained from compression tests in the Colorado School of Mines Mining Research Laboratory led to an investigation of a good method of making a simple unidirectional compressive strength test.

Jan 1, 1963

By Frank E. Woolley, Robert D. Pehlke

Jan 1, 1965

THE first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Minersville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal resources of this district, until at present-productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some .easily accessible point on the outcrop with a single entry, usually 1 1/2 yd. wide. Rooms or gangways were turned to the

Jan 10, 1926

By Maureen G. Johnson

At least three million ounces of placer gold has been mined from hundreds of deposits in the Southwest since the 1600's. Nevada, the most productive state, produced about 1,700,000 oz. Most of the placers are in accumulations of unsorted, coarse, angular gravel in gullies, dry washes, and on hill- sides. The gold is mixed with debris from the adjacent bedrock and is typically concentrated at or near bedrock or on clay layers or caliche-cemented gravels above bedrock. The most extensive and productive placers are thick accumulations of debris in well-defined stream or gully channels, in alluvial fans at the edges of the range fronts, or as thick residuum on hillsides. With very few exceptions, the gold has been transported only a very short distance from the source. Numerous small high-grade gold-quartz veinlets, rather than single large lode deposits, are by far the most common source of placer gold. Most placer mining consisted of small-scale one-or two-man operations using rockers, pans, and sluices when water was available and dry-washing machines when it was not. Where gravels were deep the miner would dig shafts to bedrock and drift along the paystreak. Large-scale operations in the major districts utilized floating or stationary dredges or, more rarely, hydraulicking to mine extensive deposits. An adequate supply of water for efficient concentration of gold has always been a major problem in the Southwest. To overcome this problem, difficult and sometimes ingenious techniques were used-pipelines to carry water for miles to the placer area were constructed, or gravel was hauled to central washing plants where water was available; numerous designs of dry-washing machines were invented. In some districts, attempts to mine the gravels by large- scale operations failed because the gravels were too wet for dry concentration methods, and no water was available for wet methods; or, when water was available, the gravels were too porous to retain sufficient water in the dredging pond.

Jan 3, 1974

By H. M. Howe

One of the little electric-resistance magnesia crucible-furnaces which I designed for the metallurgical laboratory of the School of Mines of Columbia University is shown, in vertical section, of full natural size, in Fig. 1. The furnace itself consists of two semi-cylinders of magnesia, A A, with a cover of magnesia, B B, and a stopper, C, also of magnesia, which is perforated to admit the leads x, y, of a thermo-electric couple. The furnace is heated by the spiral of platinum wire, D D (entering and departing by the openings I and K), through which a current of any desired strength is passed, bringing it to incandescence, and to ally temperature, not above the melting-point of platinum, which may be desired. The crucible E, actually used in this furnace, is also of magnesia. I have heard of some unsuccessful attempts with furuaces of this general class, and have attributed these failures to the use of siliceous materials for the furnace-walls. Of course such a result is what we should expect, since the silica mould readily be electrolysed by the current, and the resultant silicon would alloy with platinum ; but the little magnesia furnace here clescribed seems to be wholly free from this objection. It has been used in my laboratory for some months, and temperatures, up to 1100° C, hare been developed in it over considerable periods of time—indeed, it has been held near 1400" C. for about two hours—without indication, thus far, of any deterioration of the platinum. In the section shown, F F are a pair of steel disks, bound together, but separated by the inverted thermo-junction, N, of the thermo-electric pyrometer. This arrangement permits the observation and record of retardations in the heating and cooling of F F—in other words, the determinations of the cooling curves of steel—a purpose for which the furnace has been used, thus far, more frequently than in the determination of meltingpoints. For the latter operation, however, it is also suitable.

Jan 1, 1902

By Albert H. Chester

DURING the summer of 1875 I visited some of the iron mines of Houghton County, Mich., and was quite interested to observe the progress made there within a. few years. Working in open pits is gradually giving place to underground work in most of the mines where this system is practicable. In some cases, as in the Lake Superior Mine, the body of ore is so irregular, and the deposit so liable at any time to be pinched out, or nearly so, that it has been found impractical, if not impossible, to lay out any plan for systematic underground work. But in many other mines the deposit is so regular in character, that the work can be laid out in shafts at regu¬lar intervals, and a series of 60 feet levels. The Michigammi Mine, opened in 1872, and first worked in 1873, is arranged on this plan, though some quarrying is still done. But the men are being put at overhead stoping as fast as it can be got ready for them, and before long it will all be worked in this way. The New York Mine is undergoing a similar change to the pillar system, and several others have either been changed, or it is about to be done. My principal object in visiting this region was to obtain samples from some of the important mines, so as to be able to answer the question : "What is the average percentage of iron in the Lake Superior ores?" Most iron furnaces work on mixtures of ore, so that it is impossible to tell, from their records, just the percentage in each one.

Jan 1, 1876

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By Jacob T. Wainwright

The object of this paper is to describe some efforts and observations by the writer relating to this subject. Althongh the usual type of' blast-furnace is a most efficient device for smelting and melting purposes, it is not suitable for utilizing the cheaper grades of fuel, such as coal-slack and certain gaseous fuels. This problem not only involves the consideration of the furnace as a suitable apparatus, but also embraces the consideration of the chemical and calorific properties of the proposed fuel. In the hearth of the ordinary blast-furnace an extremely high temperature is maintained. This extreme temperature is due to the complete combustion of the fuel in the hearth, and before the gases reach the zone of fusion their temperature is reduced, by the absorption of carbon, 2300 degrees Fat). In a smelting-furnace, the maintenance of this extreme temperature at the hearth becomes useless when it can be reduced without

Jan 1, 1889

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By H. A. Kuhn

The Pittsburgh coal field in Western Pennsylvania is conceded to be the most important in the world.

Jan 1, 1915

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By M. Gensamer

In applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "LÜders'" lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiterl though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By M. Gensamer

In applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "LÜders'" lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiterl though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By Calvin C. Brown

A university is a place to build minds and develop leaders. It provides the tools necessary for the development of new ideas which come from the inquisitive mind and is one of the stepping stones to management responsibilities for the truly ambitious. However, it is not always a financially sound investment! Lately, there have been several articles published on the economic advantages of a college education. These articles tend to average wages together according to education and years of service. Their tabulations generally include the chairman of the board, various vice presidents and plant managers and do not reflect the achievement of the average graduate. They consistently fail to include an analysis of the investment a college education requires. In reality, the bright high school graduate would make more real money over a 20-year period if he went directly to work "on the hill" than he would if he graduated from college. Furthermore, he would find little difference between his wages and those of the college graduate in the period from 20-30 years after high school graduation.

Jan 1, 1971

By Philip R. Strand

Vermiculite is the name used for those micaceous minerals with a ferromagnesian aluminum silicate composition and the unique property of exfoliating to a low density material when heated. Commercially, the exfoliated products are also called vermiculite, or more exactly, expanded vermiculite. In its exfoliated state, vermiculite serves many markets, chief among them construction, agriculture, horticulture, and general industry. Composition and Properties Vermiculite, in a natural state, has the characteristic mica habit, splits readily into thin laminae, flexible but inelastic. In a mineralogical sense, vermiculite is a hydrated silicate with no exact chemical composition. The structural formula for a macroscopic, trioctahedral vermiculite may be written: [ ] The structure of vermiculite is basically that of a talc, and it could be regarded as a trioctahedral member of the smectite group. Macroscopically, vermiculite displays the prominent monoclinic crystal faces that are commonly marked by lines at 60° and 120°. Hardness varies from 1.5 to 2.8 or more; specific gravities are between 2.1 and 2.8; color is amber, bronze, brown, dark green, or black. When heated quickly to an elevated tempera¬ture, vermiculite expands by exfoliating at right angles to the cleavage, into wormlike pieces (the name vermiculite is derived from the Latin `vermiculare,' to breed worms). This characteristic of expansion, the basis for commercial use of the mineral, is the result of the mechanical separation of the layers by the rapid conversion of contained water to steam. The increase in bulk volume of commercial grades is 8 to 12 times, but individual flakes may expand as much as 30 times. All expansion occurs at right angles to the basal cleavage. Vermiculite may also be expanded by a number of chemical processes such as soaking in hydrogen peroxide, weak acids, and other electrolytes. There is a color change during expansion that is dependent upon the composition of the vermiculite and furnace atmospheres. Heating in an oxidizing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. The exfoliation of the vermiculite crystal results in large pores being formed between groups of platelets. Thus exfoliation can make available a large increase in void volume without significantly changing the surface area of the platelets. This characteristic is important in the chemical carrier applications of vermiculite. Although there has been much research on the chemical and structural composition of vermiculite, an exact formula and composition cannot be described. This is to be expected since vermiculite derives from a number of different mineral sources. As has been proposed, vermiculite is not a single mineral species, but families of related minerals. Additionally, commercial interest in the end product has resulted in the name vermiculite being applied to the very voluminous, bloated products from calcination of baueritized (bleached) phlogopite. This has also resulted in many names for the specific vermiculite found in a particular deposit. All of this difficulty arises from the nature of its crystal chemistry. Consequently, vermiculite is now thought of as several related variable mineral series rather than a group of related species. The vermiculites have a common silica tetrahedral sheet structure with separating ions. It is now generally agreed that vermiculites must also be regarded as true clay minerals. The properties of the mineral, such as cation exchange capacity, organic complexing ability, and vari-

Jan 1, 1975