Search Documents

By G. P. de Forest, G. O. Hiers

The object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line; (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the results of Miller,' by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-curve experiments and microscopic examination reported here. Solution of Copper in Molten Tin To determine the amount of copper that would be dissolved by molten tin at a given constant temperature the apparatus shown in Fig. 1 was used. It consists of a cast-iron pot a, 6 in. deep and 8 in. dia., well cleaned inside and dressed with graphite. This pot, which holds 15 lb. of tin, g, rests on a hot plate b with resistance winding c. The thermocouple d leads to a Wilson-Maeulen temperature regulator for maintaining the temperahre at the heating coils at a fixed temperature to within ±5°C. There is a shallow bath of solder e on the top of the hot plate to improve the thermal contact between the plate and the pot. An insulating jacket f of asbestos prevents the irregular radiation of heat from the apparatus. The copper stirrer h slowly rotates in, and is dissolved by the bath of molten tin g. This bath is protected from excessive oxidation by a layer of charcoal j. The stirrer h is fixed to the lower end of the iron tube k, which is so mounted that it can be driven by a motor with reducing gear. The temperature of the bath is indicated

Jan 1, 1930

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.' Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-' have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.' Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.' The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6' and 16" crystals and with 1300 ppm oxygen in the 33' crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.'p7

Jan 1, 1969

By AIME AIME

ONE hundred and eighty-three A.I.M.E. members, W. S. Morris with an excellent technical program, John Suman, "oil" President of the Institute, and a Texas norther blew into Dallas for the fall meeting of the Petroleum Division at the Adolphus Hotel, Oct. 16-18. and the most successful result will give future meeting committees a high mark to equal. People were still talking of the terrific heat the week before and it was quite noticeable that with the lowered temperatures, the members were in fine fettle for the technical sessions. The total attendance on Friday noon was

Jan 1, 1941

By Herbert Hoover

This paper is in the nature of a rough preliminary report on the progress that has been made in the application of the mass spectrometer to various problems arising in the petroleum industry. A few years ago the authors considered a number of the problems that were arising in the qualitative and quantitative measurement of small amounts of hydrocarbons. The methods available of making analyses by chemical techniques appeared to leave much room for improvement. Without going into the reasons at this point, attention was turned to the possibility of employing physical instead of chemical methods of accomplish-ing the desired results. A preliminary investigation disclosed that the mass spectrometer presented a possibility of solving many problems which could not easily be accomplished by other methods. Work was begun in developing the necessary apparatus and technique. A great deal of encouragement and many valuable suggestions were received from Dr. Robert A. Millikan, Dr. W. R. Smythe, and Dr. W. N. Lacey, of the California Institute of Technology, and from Dr. E. 0. Lawrence, who recently received the Nobel Prize, of the University of California. The authors particularly wish to acknowl-edge the very great willingness of these out-standing scientists to be helpful in solving many of the problems that were involved. So far as the authors are aware, this was the first application of the mass spectrometer to commercial work. The results were considerably better than had at first been anticipated. Briefly, it is pos-sible to run a qualitative and quantitative analysis of an unknown mixture of hydro-carbon gases, with an accuracy of better than plus or minus 5 per cent of each of the various constituents. An exceedingly high degree of sensitivity has been obtained, and a relatively short time is required to com-plete an analysis. Furthermore, it is un-necessary to separate a mixture of gases into its various components in order to complete the analysis.

Jan 1, 1940

By C. R. Fondersmith, John Chipman

In the manufacture of rimming steel—which constitutes the bulk of the world's production of mild steel—the factors that determine the quality of the product are very closely associated with the pouring and solidification of the steel in the ingot mold. The behavior of the metal in the mold is, on the one hand, the resultant of the complex processes through which the liquid metal has passed, and, on the other, it is an indication of the probable behavior of the ingot during subsequent rolling and finishing operations. A detailed study of the mechanism of solidification of rimming ingots ought to yield information that will be useful in controlling the structure of the ingot and the quality of the ultimate product. The first step in such a study is to determine the rate at which the solid shell of the ingot forms from the liquid metal in the mold. A knowledge of the rate of solidification will make it possible to correlate observations of rimming action and gas evolution with studies of the structure, porosity, and segregation within the ingot. Thus, if the metal in the mold is observed to fall, let us say one minute after pouring, the portion of the structure associated with this fall will be located in the part of the ingot that is solidifying at that particular moment. The knowledge that the ingot solidifies to a depth of 3/4 in. in the first minute enables us to locate in the ingot the structural features corresponding to the observed fall. Conversely, the blowhole condition associated with a rising or growing ingot will be found in the part of the ingot that is solidifying at the time the phenomenon occurs. The time required for the complete solidification of an ingot has long been a matter of speculation. It is of considerable practical importance in connection with charging and heating in the soaking pits. Too rapid handling of the ingot through heating and rolling processes has been thought to be associated with excessive pipe and other internal defects, so that a further object of this investigation was to attempt to estimate the time required for complete solidification, or the minimum practical time within which the subsequent operations can be performed with the minimum hazard.

Jan 1, 1937

By Mary Sue Coates

Characterization of the rock mass in which deep underground structures are to be located is of critical importance to the feasibility and design of the structures. The process involves areal studies, subsurface exploration and extensive testing to obtain comprehensive data on the rock units which will enclose the excavated structures. The Illinois Deep Hole Project provides an example of characterization of rock at great depth describing the types and variety of tests and studies which were utilized and the results obtained.

Jan 1, 1984

By Frederick N. Rhines

BECAUSE of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding 'their occurrence, even though the fundamental mechanisms involved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpret the next. It is the purpose of the present paper to present, by means of examples drawn from practice, a brief survey, of the ways in which gas-metal diffusion serves and obstructs the purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with but brief mention of parallel cases. THE NATURE OF GAS-METAL DIFFUSION The term "gas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to- regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. No element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Donald M. Liddell

From a commercial standpoint, the only beryllium mineral warranting attention is beryl, 3Be.Al2O3.6SiO2, which is of fairly widespread occurrence. The chief deposits are in Brazil, Argentina, India, Canada and Portugal. When pure this contains about 14 per cent of beryllium oxide. The mineral richest in beryllium is phenacite, (BeO)2SiO2, or beryllium orth-osilicate, which contains 45.55 per cent beryllium oxide when pure, and if anyone is ever fortunate enough to discover a large deposit of it, it will revolutionize beryllium metallurgy. Gadoljnite, zBe0.Fe0.2Yz0~.zSi0~, is also often referred to as a beryllium mineral, though the occurrences are comparatively scant and it is of more interest as a source of yttrium than it is of beryllium. There has been a good deal of talk recently regarding some occurrences of helvite in the United States. Helvite is a complex manganese-iron beryllium silicate and, apart from difficulties that would arise in its treatment because of its compo-sition, the beryllium content of the known deposits is not high. Early Metallurgy The elemcnt beryllium was first isolated by L. N. Vauquelin in 1797.~ He crushed and heated beryl, having the idea that this heating made it more readily amenable to attack by chemicals, and then mixed the mineral with three times its weight of caustic potash and fused the mixture. The melt after cooling was dissolved in hydrochloric acid: dehydrated, and again taken up with hydrochloric acid and filtered to separate the silica. The filtrate was treated with an excess of potassium carbonate and the precipitate after draining was leached with a solution of caustic potash, which dissolved the alumina. The undissolved material was, in Vauquelin's own words, "une terre nouvelle." He dissolved the precipitate with nitric acid and evaporated it to dryness, took up with hydrochloric acid and threw the iron out with potassium hydrosulphide, though he found that to make a complete separation of the iron involved a second treatment. The solution, after throwing out of the iron, had a pronounced sweet taste, and though Vauquelin always speaks of working on "terre du beril" he suggests that the new element should be known as "glucine" (glucinum) from the Greek word for sweet, because of this outstanding property. Vauquelin did considerable work on the comparison of aluminum and beryllium, working out a separation of most of the aluminum based on its precipitation as alum. His work is reviewed at some length, since ordinarily his procedure is incorrectly stated. It will also be recognized by those who have studied beryllium metallurgy that a good many technicians have followed his ideas since, including preheating the beryl before treatment. The fusion with

Jan 1, 1944

By Charles C. Peterson, Ronald E. Enstrom

Significant improvements have been made in the ursine systern for epitaxial vapor gvowtlz of Gds. The electron concentration has been reduced to below 1015 cm-3 with electron-mobility values as high as 7200 sq on per v-sec at 30PK and 60,000 sq cw7 per v-sec at 77°K. These high-purity layers have been successfully gvown on n&apos; layers with thicknesses as snzall as 1 p and as large as 125 p. Furthermore, high-purity layers have been incorporated into an structure without degradation of electrical properties. Different impurity gradients at the n&apos; to n interface were achieved. Using these structures, Gunn oscillators have been operated at frequencies as low as 0.4 GHz and as high as 40 GHz, which equals the highest valzle yet reported. The frequencies nleasured are in reasonable apeenlent with those calculated fron7 the n-layer widths and the transit times. CW operatiolz has been achieved from 3 to 20 GHz. In Gunn devices for >40 GHz operation (i.e., witk an n-layer tkickness below 2.5p), the n layer has been generally too pure to permit oscillations to occuv. ThE mechanism of the Gunn oscillator&apos; is now generally understood.2-5 Electron transfer from the (000) minimum to the ( 100) minima leads to a voltage-controlled negative resistance, which results in the formation of domains of high and low electric fields which travel through the crystal with a characteristic velocity of about 107 cm per sec. When a constant voltage is applied to the sample, this domain motion generaliy leads to oscillations at the transit time frequency, fT = 107/L, where L is the thickness of the active n layer.&apos; In this case, a single high-field domain is nucleated at the cathode and grows until it reaches the anode, where it is absorbed; a new domain then forms at the cathode.5 There are related modes of oscillation of the same device in which a tuned circuit causes a periodic variation of the voltage across the device. The frequency then may be either above or below fT. It has been shown that oscillations will occur when n • L 2 1012 cm"2, where n is the carrier concentration in the active region. At lower doping densities, 10" 5 n . L 5 lo&apos;&apos;, the doping is said to be subcritical for oscillation and the description of the device operation changes since the domains become comparable in thickness to the device thickness, L. Nevertheless, such devices have been found to be "active" and, in fact, are useful as amplifiers.778 For CW operation, one wishes to minimize the power dissipation, which is related to the electric field, E, and the low-field resistivity, p. Below threshold, the power dissipation density is approximately Typically, at threshold where E -- 3 x 103 v per cm, the dissipation density is 107/p watts per cu cm, p in ohm-cm. Furthermore, it is desirable to provide good conduction of the heat generated in the active region. The temperature rise, AT, across the active layer of a sandwich structure, with a heat sink on one side, is given by AT = (E&apos;/P)(L~/~~) where it is assumed that the thermal conductivity, u, and resistivity, p, of GaAs do not vary appreciably over the range of temperature and electric fields existing in the layer. This expression shows that, subject to maintaining an appropriate (n . L) product, CW operation is favored by a higher resistivity, a lower threshold field, and a thinner device. The above device requirements place some severe restrictions on the materials to be used, especially for high-frequency (>10 GHz) operation. Here, it is necessary to prepare very thin (<10 µ) layers of GaAs, in a state of high purity (-1 ohm-cm), complete with very low-resistance ohmic contacts. Problems of handling such thin and fragile samples become inereasingly severe as the frequency is raised. Furthermore, while good low-resistance ohmic contacts are easily applied to low-resistivity GaAs, contacting difficulties are encountered for these higher-resistivity materials.

Jan 1, 1968

By Jr. J. L. Ryon.

Experimentation with ammonium nitrate-fuel oil mixtures at three underground salt mines revealed its excellent applications at those properties. The author relates the present blasting practice used at these mines by the Intemzational Salt Co. The International Salt Company is presently performing blasting operations with a pneumatically -placed ammonium nitrate-fuel oil mixture at three rock salt mines, and plans its use in the near future at its new Cleveland mine. Use of ammonium nitrate is saving the company approximately $250,000 annually. With rapidly increasing operating expenses and increasing competitive pressure resulting in lower prices, savings such as those realized through the use of ammonium nitrate are vitally important. ORIGINAL INVESTIGATION AND EXPERIMENTAL ACTIVITIES The three mines presently involved are located at Detroit, Mich.; Avery Island, La.; and Retsof, N. Y. Initial experiments were conducted at the Detroit mine where a detailed investigation was carried on to determine the significance of the static electricity factor when blowing ammonium nitrate into drill holes in which millisecond delay electric blasting caps had been placed. Although the information developed at the Detroit mine was passed along to the other mines, each mine independently pursued its own course of inves- tigation. This fact, plus the differing mining conditions, resulted in slightly different operational procedures at each mine. Some of the varying statistical data are shown in Table I, and data common to all three International Salt Company mines are shown in Table 11. BLASTING PROCEDURE AT THE DETROIT MINE This mine has been using the ammonium nitrate-fuel oil mixture for more than two years on a full time production basis and represents the successful detonation of several hundred thousand holes. Results have been excellent and the blasting cost has been reduced many times. The actual operation at Detroit consists of adding the fuel oil to the bags of ammonium nitrate by means of a portable fuel oil tank complete with hose, nozzle, and metering device. The bags of the ammonium nitrate-fuel oil mixture are transported to the working face from the oiling area by means of a jeep-drawn trailer. At the face, the ammonium nitrate is placed on the elevating platform of a powder-load ing rig which consists of a pneumatically-tired, large fork-lift truck with a fully insulated elevating platform constructed on the forks. The placement of the dynamite primer and the pneumatic placement of the ammonium nitrate is a two-man operation. First, one cartridge of the primer is placed in each hole on the line of holes which can be reached from the loading rig platform. The plastic hose is then inserted into the hole and pushes the primer to the back of the hole. The proper charge of ammonium nitrate is then placed in the pneumatic placement machine and,

Jan 1, 1961

By Robert H. Carpenter

Major trends in exploration geochemistry during the past year included an increased level of geochemical exploration by both government and private industry: greater sophistication in sampling, analytical and interpretive techniques: and increased activity on the part of universities and state geological surveys. The evolution of applied geochemistry in North America from a useful prospecting tool to an invaluable exploration method is largely due to efforts of the mining industry, the USGS and the Geological Survey of Canada. In the U.S., there has been a distinct reluctance on the part of universities to conduct research or to offer courses dealing principally with applied geochemistry. Most university geochemists have not been responsive to industry needs because government sponsorship of geochemical research in universities has been overwhelmingly in favor of theoretical, rather than applied research: and, because of the mistaken notion that exploration geochemistry is not sufficiently academic. A critical shortage of specialists in this field has resulted. Specialists in Exploration Geochemistry Needed Based on the response to a brief questionnaire sent to universities in the U.S. and Canada, there is some evidence suggesting a reversal in this trend. Graduate courses devoted to exploration geochemistry are currently being offered in geology departments at the following universities: University of British Columbia, Colorado School of Mines, University of Idaho, McGill University, University of New Mexico, Pennsylvania State University and the University of Utah. Other departments report that applied geochemistry is included in general geochemistry courses. A survey of recent publications suggests increased research interest in exploration geochemistry by university geologists.

Jan 1, 1970

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.&apos; The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.&apos;

Jan 1, 1964

By Walter Miller

Construction of new large refineries was small in 1937, but extensive modernization and expansion of existing plants were made, bearing out the observation of the Bureau of Mines that the trend is strongly toward fewer and larger refineries. Building the first large combination skimming and cracking unit of 20,000-bbl. capacity was a startling achievement four or five years ago, but it has been exceeded many times since, and at least four units with a capacity of 30,000 bbl. or more were contracted for during 1937, as well as many other units of smaller but still substantial capacity. Installation of polymerization plants for producing high-antiknock blending naphthas from refinery gases progressed at an accelerated rate in refineries affording sufficient raw gas to make the use of the process profitable. The total productive capacity of polymerization units built and contracted for in the United States is now about 25,000 bbl., equivalent to the gasoline production from approximately 55,000 bbl. of crude oil a day. Octane Fuels Also utilizing refinery gases—the butylene fractions in particular—the plants for manufacture of iso-octane increased in number to such an extent that the combined capacities will enable the air forces of the United States shortly to go entirely to the use of 100-octane fuel, indications being that the Army will reach that position in 1938, with the Navy not far behind. Commercial air-lines are expected to take advantage of the greater power of high-antiknock fuels to gain the increased power and increased pay loads possible with their use. Work done on producing fuels with octanes beyond the 100 point has recently been reported, and their production can be expected, although at high cost, when the economics of the situation justifies and engines capable of utilizing them efficiently are available. In the field of motor fuels, important work was reported to the A.P.I. at its annual meeting, on the effect of altitude on antiknock requirements

Jan 1, 1938

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows : I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment&apos;s reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

By Ralph Arnold

PERHAPS the most striking feature in the three newly discovered fields in the Los Angeles basin is the enormous thickness of oil sand. The total thickness is not yet known in any of the fields, since no well has as yet been drilled deep enough to pass through it. In the Signal Hill area a maximum of 1500 ft. or more of productive sand has been penetrated. In the other fields the interbedding of considerable shale members renders the total sand thickness somewhat less, but in all cases the depth of sand strata is enormous when compared with other California fields. For instance, in the Coalinga field the total thickness of sand on the average has been less than 100 ft., while in the Midway and Sunset fields not more than 250 ft. of actual productive sand has been encountered in any one place. This condition has so upset all previous ideas regard-ing the possible future production that but few of the engineers who have had to deal with the situation feel

Jan 5, 1923

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known out crops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The Oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this coal can be used in steel production is will be possible for the Mexican steel industry to reach new dimensions, commensurate with the growing industry of the central region. Coal can be utilized in thermoelectric plants in this area, which lacks not only petroleum and natural gas but also electric power. It can be used as domestic fuel, replacing charcoal and firewood.

Jan 5, 1954

By Thomas M. Drown

THE method usually employed in accurate determinations of sulhur in pig-iron and steel is to treat a weighed sample of borings in a flask with muriatic acid, and to pass the gaseous products through an alkaline solution of lead or silver, which precipitates all the sulphur of the sulphuretted hydrogen in the form of sulphide of lead or silver. The sulphide thus formed is subsequently oxidized by aqua regia, bromine, or other oxidizing agent, and the sulphuric acid formed precipitated in the usual way by chloride of barium. I have substituted for the alkaline metallic solution, a solution of permanganate of potash in the strength of one gramme of permanganate to 200 cubic centimetres of water, and find that it gives results quite as accurate as those obtained by using an ammoniacal solution of silver. By the employment of the permanganate it will be readily seen that there is considerable saving of time and work. In order to test the accuracy of the method, six samples of pig-iron borings were weighed out (about six grammes each) and treated identically

Jan 1, 1874

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,&apos; shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,&apos; shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951

By Claudio Gutierrez

It has been claimed (Eadington and Rosser, 1969) that when freshly precipitated lead sulfide is in contact with oxygen-containing water, there is an "induction period" of at least a few hours during which no detectable oxidation of the lead sulfide takes place This effect would be of the utmost importance for the adsorption of xanthate on galena in flotation mills. It was tried here to reproduce the results obtained in (Eadington and Rosser, 1969), but no "induction period" was found. Besides, reasons are given to prove that the oxidation mechanism proposed by Eadington and Prosser (1969) is not realistic.

Jan 1, 1982