Search Documents

By C. P. Kempter, H. L. Brown

Recently Chang determined heat content values of tantalum monocarbide and tungsten monocarbide from 325" to985°Kand 326" to 912"K, respectively, and, using other published data, made certain solid-state calculations for these two compounds. Chang expressed his Cp values in units of cal per "g-atom alloy" OK. We consider this poor usage since l) tantalum monocarbide and tungsten monocarbide are not alloys, and 2) an atom of an alloy does not exist. However, one may convert his values to units of cal per mole OK by merely doubling them. For TaC he calculated a Nernst-Lindemann parameter of 9.07 x lo-' "g-atom per cal". We have refined the calculation of this parameter and have arrived at a much lower value. Rather than approximating the true coefficient of volume expansion, a,, as three times the true coefficient of linear expansion, a, we calculated u, from the TaCo.99, lattice expansion data of Fries and Wahman.38 At 25°C a, = 14.3 x 10s per OC. The molar volume was calculated to be 13.32 cu cm per mole at 25°C. From the lattice compression data of Champion and Drickamer~' for "TaC,.,," we determined the room-temperature compressibility to be 3.5 x 10-l3 sq cm per dyne by plotting l/Vo (aV/ap) vs applied pressure. (Since the lowest pressure at which Champion and Drickamer reported a relative volume was 20 kbars, one may calculate an approximate compressibility only. Chang calculated a compressibility of 3.175 x 10-l3 sq cm per dyne from the same data.) We also used twice Chang's value of Cp = 4.38 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated a Nernst-Lindemann parameter of 5.8 x 10-l4 mole per erg or 2.4 x lo- ' mole per cal, and a Cdil value of 2.3 x 10' ergs per mole OK. In the case of tungsten monocarbide no isothermal compressibility has been reported; however, one may calculate an approximate Nernst-Lindemann parameter by using the adiabatic compressibility reported by Brown, Armstrong, and Kempter." Using the WC lattice expansion data of Mauer and Bolz~l we calculated a, to be 12., x l0-' per OC. The molar volume was calculated to be 12.5 cu cm per mole. We used twice Chang's value of Cp = 4.18 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated an approximate Nernst-Lindemann parameter of 2 x lo-' mole per cal, which is much

Jan 1, 1969

By Stanley C. Herold

At the present time five localities in the Argentine Republic are known to bear direct evidences of the presence of petroleum. The segregation of these localities is more or less arbitrary inasmuch as minor indications may be found to extend from one locality to the other at no regular distance apart, especially in the northern and western part of the republic. These localities are listed as follows: North Argentine-Bolivian region, Salta-Jujuy district, provinces of Mendoza and Neuquen, Comodoro Rivadavia, and the Gallegos-Punta Arenas region. Economic conditions attract us to the possibilities of developing these and other regions of countries in the southern hemisphere. Development work will, naturally, be undertaken first in such localities as present direct manifestations of the presence of petroleum; "hidden fields" may exist, but, unless discovered by accident, their development will be left to the last. The problems to be solved in the development of the petroleum resources of the Argentine republic are mainly of stratigraphy, structure, and transportation. We are not here concerned with the unfavorable climate of the countries to the north in the tropics where, for us of the "far north," life hangs by a thread ready to be severed by a mosquito, gnat, or tropical germ. North Argentine-Bolivian Region The North Argentine-Bolivian region has already been described by the author.' Geographically and geologically this is admittedly one field extending from Argentine into Bolivia. It is not necessary to repeat here the various conditions pertaining to this field, though the summary may be quoted as follows: Extending from northern Argentine northward into central Bolivia is a belt of petroleum seepages. On account of the remoteness of the district it has, heretofore, been little considered by oil operators. The regional geology is comparatively well understood but the local features have not been carefully detailed. Development work in the past has been done on an unscientific basis and has led to failures. At the present time, access to the region is somewhat difficult but, no

Jan 1, 1921

IF you do not make the disc at the same time as the core and as part of it, it is necessary to make it by itself. This is done by spreading on a board or other flat surface a layer of clay as thick and wide as [88] the disc that you made at the feeding head of the first pattern of the gun. When it is dry, mark it exactly with compasses and then, cutting with a chisel or rasp, make it fit exactly into the empty space at the head. Likewise, make a hole just as wide as the thickness of the core exactly in the middle of this clay disc. When you have put the disc in its place in the mould and then pass the core through this hole, it passes exactly through the center of the mould in such a way that it meets the iron ring that you put at the foot of the mould for this purpose. As I said above, if' you do not make it as part of the core, it is necessary to proceed in the aforesaid way. But if' you wish to make it attached to the core (which I like better because it can be done more accurately) make a

Jan 1, 1942

By J. L. Jernegan

In the summer and fall of 1875, the author was present during a short smelting campaign at the Hall Valley works, and having had occasion to make a number of chemical analyses of the ores, fuel, and fluxes, deems that the results of the same, and also an account of the smelting operations, may be found of interest to members of the Institute. The mines and reduction works of the Hall Valley Silver—Lead Mining and Smelting Company (limited) are situated at Hall Valley, Park County, Colorado. The smelting works are located about half way from the mouth to the head of the above-named valley, and the mines high up on the mountains, near its head. The three principal mines of the company are the Whale, Leftwick, and Coldspring. They are all on different veins, running parallel to one another, with a general trend from southwest and northeast. The

By J. L. Jernegan

IN the summer and fall of 1875, the author was present during a short smelting campaign at the Hall Valley works, and having had occasion to make a number of chemical analyses of the ores, fuel, and fluxes, deems that the results of the same, and also an account of the smelting operations, may be found of interest to members of the Institute. The mines and reduction works of the Hall Valley Silver-Lead Mining and Smelting Company (limited) are situated at Hall Valley, Park County, Colorado. The smelting works are located about half way from the mouth to the head of the above-named valley, and the mines high up on the mountains, near its head. The three principal mines of the company are the Whale, Leftwick, and Cold¬spring. They are all on different veins, running parallel to one another, with a general trend from southwest and northeast. The

Jan 1, 1877

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By D. N. Stevens, D. N. Bloom, M. A. Klugman

This paper represents a portion of a larger study concerning dispersion of major, minor and trace elements in wall-rock about orebodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to orebodies in two mines, one in the Horseshoe Mining District (Hilltop mine), and the other in the Alma Mining District (Phillips mine). The two districts lie adjacent to one another, the Horseshoe District on the south and the Alma District on the north, and are commonly referred to as one, the Alma-Horseshoe Mining District. The Alma-Horseshoe Mining District is located 80 miles southwest of Denver, Colo., (Fig. 1) in Park County, on the eastern slope of the Mosquito range. The area is typified by rugged relief with altitudes of from 10,500 to 14,000 ft. The Horseshoe District is separated from the Lead-ville Mining District by the crest of the Mosquito range, with the Leadville District to the west. The Alma-Horseshoe District has been considered as peripherial to the Leadville District, and has not received the detailed attention that the Leadville District has. These two mines were selected for this study because of their ease of access; the attitude of the workings and the drill holes to the known mineralization; the similarity of the mineralization; and because the mineralization occurs in carbonates in both mines but are of different ages. In the Hilltop mine mineralization is confined to the Leadville dolomite (Mis-issippian) and is principally lead with subordinate zinc and silver. In the Phillips mine the mineralization occurs in the Peerless dolomite and shale (Cambrian) and in the Manitou dolomite (Ordovician) and is principally zinc with subordinate lead, silver,

Jan 1, 1964

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,'~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro'~ suggested that the strain E can be deduced

Jan 1, 1970

By N. J. Olson, G. W. Toop

A series of equations previously derived for calculating ternary thermodynamic properties using binary data has been applied to the problem of predicting ternary phase diagrams and quaternary excess free energy. The methods are considered to be rigorous for regular ternary and quaternary systerns and empirical for nonregular systems. The equations have been used to predict ternary phase boundaries in the Pb-Sn-Zn system at 926°K and the Ag-Pd-Cu system at 1000ºK. Calculated quaternary excess free-energy values are presented for the Pb-Sn-Cd-Bi system at 773°K. A method for predicting the location of ternary phase boundaries would be a useful supplement to experimental measurements in ternary systems. This has been recognized with the considerable work that has been done to find models to predict or extend thermodynamic properties and phase diagrams in binary and ternary systems1-18 for which direct experimental measurements are limited. With the access to highspeed digital computers and mechanical plotting devices, it is currently rather easy to compare mathematical models with experimental data. The regular-solution model is consistent with systems which exhibit negative heats of mixing, positive heats of mixing, and miscibility gaps, and therefore it is applicable to simple phase diagrams. The purpose of this paper is to illustrate the use of regular-solution equations to predict, empirically, phase equilibria in some types of nonregular ternary systems. Corresponding equations for regular quaternary systems are given and used to calculate empirical quaternary excess free-energy data. METHOD FOR PREDICTING THE LOCATION OF TERNARY PHASE BOUNDARIES USING BINARY DATA Meijerin1,6 has used the regular-solution model to calculate common tangent points to ternary free energy of mixing surfaces and hence to determine phase boundaries in ternary systems involving miscibility gaps. He used the following equation to calculate ternary excess free energy of mixing values: stants characteristic of the binary solutions, and Ni is the mole fraction of component i. An alternate expression which gives for regular solutions as a function of binary values of along composition paths with constant N1/N2, N2lN3, and N1/N3 may also be derived:15 ternary r xs 1 ?c-*n.Ti*.U*. This expression for is more useful for the empirical calculation of ternary excess free-energy values for nonregular systems because actual binary AFXS data may be used in the expression rather than attempting to find suitable constants for Eq. [I]. The results of this feature of Eq. [2] are illustrated in Table I where calculated excess free-energy values for the Ni-Mn-Fe system at 1232°K are compared with experimental data of Smith, Paxton, and McCabe.19 Although regular-solution equations have been shown to give calculated thermodynamic quantities which agree quite well with experiment for single-phase nonregular ternary systems,14,15 care should be exercised in the use of the equations to predict thermo-dynamic properties of multiphase ternary systems in which strong compound formation is suspected. This precaution is consistent with the simple regular-solution model which for negative values of ai_j will indicate a tendency toward compound formation but even for very large negative values of ai-jwill not give multiphase binary or ternary systems involving a distinct stable compound. Hence, calculated ternary free-energy data using Eq. [2] might be expected to vary between being rigorous and poor, in the following order, for ternary systems which are: a) regular solutions, b) nonregular single-phase liquids in which random mixing is nearly realized, c) nonregular single-phase solids, d) nonregular multiphase systems exhibiting miscibility gaps, e) nonregular multiphase systems with binary compounds but no ternary compounds, f) nonregular multiphase systems with highly stable binary and ternary compounds. The calculated data will be expected to be least accurate for the last two cases. The general method adopted in this paper involves two-dimensional plots of ternary activity curves. The principle used is that tie lines indicating two-phase equilibria join conjugate phases a and B for example, for which a1(a) = a1(B), a2(a) = a2(B), and a3(a) = a3(B). Tie lines may be determined by plotting the ternary activities of two components along an isoactivity line for the third component and the unique points where the above equalities hold may be found graphically.

Jan 1, 1970

By P. W. Shimer

The purpose of this note is to call attention to a source of error in the determination of graphitic carbon, made by the usual method of solution in hydrochloric acid. Although the method is tedious, because of the necessary treatment of the separated carbon with caustic potassa, alcohol and ether, the text-books seem to give it preference; and it is, perhaps, used more generally than the method of solution in dilute nitric acid. Solution in hydrochloric acid usually gives higher graphitic-carbon results than solution in nitric acid, and many, therefore, consider it more trustworthy, the inference being that the lower results obtained by nitric acid are due to the loss of some of the finely-divided graphite by reason of the oxi-

Jan 1, 1896

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

Robert Carl Sticht, member of the Institute since 1886, an American metallurgist of world-wide reputation, died in St. Margaret's Hospital, Launceston, Tasmania, on April 30, 1922, after an illness of eleven months, against which he fought with the highest courage and characteristic fortitude. The news of his passing came as a great shock to a host of his friends and former associates here, but on account of his long absence from the United States, exact biographical details have been heretofore lacking. Throughout Tasmania, the expressions of public sorrow were many and impressive, and the flags were flown at half-mast in Queenstown, Zeehan, and the entire Mt. Lyell district, in honor of the man who had won his place in the community as a great captain of industry and a man universally admired and loved. Sticht had been connected with the Mt. Lyell Mining & Railway Co. in Tasmania throughout its entire productive period. He had originally been induced to go to Tasmania through the good offices of the late Dr. E. D. Peters, then professor of metallurgy at Harvard University, who after personally examining the undeveloped Mt. Lyell properties, recommended Sticht as the best possible man to work out the complex metallurgical problem which that great orebody presented. Sticht had already made himself the leading authority on pyritic smelting, having taken up the idea as suggested and partly worked out by Lawrence Austin and carried it through to a certain degree of perfection in the case of limited tonnages of special ores. After studying the situation at Mt. Lyell, Sticht found the conditions there to be almost ideal for pyritic smelting, and he had the courage to adopt as the basis for a permanent, and eventually successful, solution of the metallurgical problem, a process that was then little more than a theoretically interesting possibility. The thorough studies and remarkable results attained at Mt. Lyell were published as chapters in Doctor Peters' various publications on the metallurgy of copper, Doctor Peters giving full credit to Sticht for their authorship. These chapters by Sticht practically constitute the: best literature of the art of pyritic smelting. The accuracy of observation,

Jan 1, 1923

Robert Carl Sticht, member of the Institute since 1886, an American metallurgist of world-wide reputation, died in St. Margaret's Hospital, Launceston, Tasmania, on April 30, 1922, after an illness of eleven months, against which he fought with the highest courage and characteristic fortitude. The news of his passing came as a great shock to a host of his friends and former associates here, but on account of his long absence from the United States, exact biographical details have been heretofore lacking. Throughout Tasmania, the expressions of public sorrow were many and impressive, and the flags were flown at half-mast in Queenstown, Zeehan, and the entire Mt. Lyell district, in honor of the man who had won his place in the community as a great captain of industry and a man universally admired and loved. Sticht had been connected with the Mt. Lyell Mining & Railway Co. in Tasmania throughout its entire productive period. He had originally been induced to go to Tasmania through the good offices of the late Dr. E. D. Peters, then professor of metallurgy at Harvard University, who after personally examining the undeveloped Mt. Lyell properties, recommended Sticht as the best possible man to work out the complex metallurgical problem which that great orebody presented. Sticht had already made himself the leading authority on pyritic smelting, having taken up the idea as suggested and partly worked out by Lawrence Austin and carried it through to a certain degree of perfection in the case of limited tonnages of special ores. After studying the situation at Mt. Lyell, Sticht found the conditions there to be almost ideal for pyritic smelting, and he had the courage to adopt as the basis for a permanent, and eventually successful, solution of the metallurgical problem, a process that was then little more than a theoretically interesting possibility. The thorough studies and remarkable results attained at Mt. Lyell were published as chapters in Doctor Peters' various publications on the metallurgy of copper, Doctor Peters giving full credit to Sticht for their authorship. These chapters by Sticht practically constitute the: best literature of the art of pyritic smelting. The accuracy of observation,

Jan 1, 1923

By H. Warlimont

Precipitation of cementite plates from carbon-rich austenite gives rise to localized formation of martensite in the matrix next to the precipitate upon quenching. The growth of this martensite is urmsually restricted. A distinct lattice relationship is found between this martensite and the cementite phase. It is concluded that the martensite is nacleated in the region of lowest carbon concentration at the austenite-cementite integace, with low-energy matching to the cementite lattice. The restriction of the growth of the martensite phase to the vicinity of the cementite plates can be explained by misfit in the austenite -martensite glissile interface and the uphill carbon gradient in the austenite. The investigation was carried out by light- and electron-microscopy and by electron-diffraction of thin foils. THE precipitation of cementite from carbon-rich austenite gives rise to a localized formation of martensite in the matrix next to the precipitate upon quenching. This behavior has been described previously by A. B. Greninger and A. R. Troiano1 for a 1.78 pct C steel ("pseudomorphic martensite"), and by A. Hultgren2 for a Fe-0.99 pct C—5.20 pct Mn steel. By measuring the axial ratio of the martensite phase,' it was found that the carbon content of this martensite was lower than that of the martensite which formed without prior partial transformation to cementite. Therefore, it was concluded that lowering of the carbon concentration in the matrix next to the precipitate raised the M, temperature locally and thus led to nucleation of martensite at the ce-mentite-austenite interface. However, the restriction of the growth of the martensite phase to the vicinity of the cementite plates cannot be explained by localized carbon impoverishment alone. Under ordinary conditions a martensite plate which has been nucleated in a favorable site can continue to grow until it encounters a physical barrier, or until it encounters a compositional barrier in the matrix, where the total free-energy change for the reaction is not negative, since it has been shown by numerous experiments that the activation energy for growth of ordinary martensite is virtually zero.' An investigation was conducted by transmission electron microscopy and electron diffraction to study this extraordinary martensite. It was expected that crystallographic in addition to compo- sitional conditions caused this abnormal mode of martensite formation. MATERIAL AND PROCEDURE An Fe-C-Mn alloy containing 1.15 pct C and 5.1 pct Mn was used for most of the experiments. For metallographic work, specimens 15 by 15 by 3 mm were used. For preparation of thin films, the initial specimen size was 15 by 15 by 0.7 mm. The heat treatment of each specimen consisted of austenitizing for 1/2hr at 1100'~ in an argon atmosphere, subsequent isothermal holding in a lead bath at one of a series of different temperatures, and, finally, quenching into brine at room temperature. For metallographic examination, the specimens were mounted in bakelite (slight tempering effects resulted from the heat in the mounting press) ground, polished, and etched in nital. Thin films for transmission electron microscopy and electron diffraction were obtained by grinding the specimens to approximately 0.2 mm thickness and subsequent electrolytical thinning. The orientation relationships were evaluated from sets of electron micrographs and selected-area electron diffraction patterns of single units of the transformation products and the adjacent matrix. RESULTS In the alloy which was used for the experiments, proeutectoid carbide precipitates over a wide tem-

Jan 1, 1962

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942