Search Documents

By Sidney G. Parker, Jack E. Pinnell

Cubic ZnSe crystals have been grown with HCl, HBr, and I, as chemical transport reagents. The growth of large, well faceted crystals is in the order HCl < HBr < I, with some produced by I, transport being 1 cm on an edge. ZnSe:I crystals showed no strain in cross polarized light and were homogeneous as determined by electron microprobe. These ZnSe:I crystals had a mobility at 25°C of about 300 sq cm per v-sec and contained 103 dislocations per sq cm; further, these crystals were pure cubic and showed both photolumi-nescence and photo conductance. Doping was attempted during crystal growth. ZnS and Zn (S,Se) crystals were also grown by I, transport. ZnSe crystals have been grown by most of the common techniques.1"6 Of these, chemical vapor transport as developed by Kaldis2 showed promise of producing high perfection, cubic ZnSe. With chemical transport, crystals can be grown far below the transition temperature for conversion of cubic to hexagonal structure. A small temperature gradient between source and growth region tends to allow near equilibrium growth, which should lead to good crystalline perfection. Because it is necessary to form volatile compounds, halogens or their compounds are extensively used as transport agents. HCl, HBr, and I, were compared as transport agents for growth of ZnSe crystals. Doping during crystal growth was attempted. ZnS and ZnSxSe1-x crystals were also grown by chemical transport. Electrical and optical properties of the crystals were examined. EXPERIMENTAL Fig. 1 is a sketch of the growth apparatus, which was a modification of Kaldis&apos;. A quartz rod which butted against the seed crystal served as a heat sink to promote growth only on the seed. Initially, crystal growth was attempted with ZnSe prepared by wet chemical methods. Because such a material contained oxides and selenates, HC1 reacted with these oxygen compounds to form H2O and no ZnSe transport occurred. Further, this ZnSe contained about 10 ppm Cu plus other impurities. High purity ZnSe, containing small amounts or no oxygen compounds, was prepared by reaction of H2Se with zinc vapors at 600° to 800°C in an atmosphere of palladium diffused H2.7 The ZnSe thus produced was usually copper free and contained only 1 ppm by weight of magnesium as determined by emission spectrographic analysis. G.E.&apos;s electronic grade ZnS, which had about 10 ppm metallic impurities, was used without further treatment. ZnS-ZnSe charges were prepared by mixing the two compounds together, then sintering 24 hr at 1100°C in an H2S ambient. The gases, HBr and HC1, were commercial grade, of 99.9 pct purity, while the I2 was 99.999 pct pure. The single crystal seeds with (111) faces for growth were mechanically held in place by sealing the outer quartz tube to the growth tube. After the charge was introduced, the system was outgassed at l0-5 torr while heated to 500°C. The desired quantities of transport reagents were then sealed off in the system, which had been cooled to 25°C. The growth tubes were inserted into a furnace with the desired temperature and thermal gradient. The system was allowed to cool for 1 to 12 hr from growth temperatures of about 850" to 25°C. The tubes remained stationary during crystal growth. HCl CHEMICAL TRANSPORT GROWTH Preliminary runs with HC1 had a temperature gradient of 100° to 200°C and no seed or heat sink. Only small crystals were obtained in these experiments as

Jan 1, 1970

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,&apos; Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By C. R. McEwen

This paper presents a technique for calculating the original amount of hydrocarbon in place in a petroleum reservoir, and for determining the constants characterizing the aquifer performance, based on pressure-production data. A method for doing this based on a least-squares line-fitting computationwus proposed by vanEverdingen,Timmerman andMcMahon in 1953. We found that their method would not work when there is error in the reservoir pressure data — even moderate error. The technique presented here appears to give reasonable answers when pressure data are uncertain to the degree expected in reservoir pressure determinations. The major change introduced in the present analysis is to limit the least-squares line-fitting to yield only one constant— the amount of hydrocarbon in place. The water-influx constant is then taken as proportional to the oil (or gas) in place. The constant of proportionality can be computed from estimates of effective compressibility and reservoir water saturation. It is also pointed out that the commonly used least-squares analysis assumes all of the uncertainty to be in the dependent variable. The material balance should be arranged so that this condition is fulfilled if correct inferences are to be made from statistical calculations. Examples are shown of the application of the new technique to gas reservoirs—both hypothetical and real—and to the oil-reservoir example of van Ever-dingen, Timmerman and McMahon. INTRODUCTION The amount of hydrocarbon originally in place in a petroleum resenroir can be estimated by means of the material-balance calculation. Simultaneous observations of pressure and amounts of produced fluids are required, together with the PVT data applicable to the reservoir fluids. If water encroachment is occurring, it is desirable to try to infer the behavior of the aquifer, as well as the original hydrocarbon in place, from the pressure-production data. This imposes additional demands on the method of calculation, and uncertainty in the data can result in large uncertainty in the answer. In addition, if the size of a gas cap is to be established, the whole problem becomes indeterminate, as pointed out by Woods and Muskat.1 Brownscombe and Collins2 simulated a gas reservoir and its aquifer on a reservoir analyzer and derived quantitative information on the effect of uncertainty in pressure and aquifer permeability on computed gas in place. Among the various techniques of estimating the performance of an aquifer, the method of van Ever-dingen and Hurst? based on compressible flow theory, seems to have been the most generally successful (see Ref. 4, for example). In this paper we shall confine ourselves to their representation of the aquifer. In 1953,&apos; van Everdingen, Timmerman and McMahon5 introduced a statistical technique for deriving the amount of oil originally in place and the parameters which describe the aquifer. (We shall refer to this technique as the "VTM method&apos;&apos;, as suggested by Mueller.6) Their example reservoir had no gas cap. It has been our experience that the VTM method gives a reasonable answer when the data are very accurate, but that inaccuracy (particularly in pressure) can cause the method to break down. The effect was first observed in gas reservoirs, but has since been seen in oil reservoirs also. In this paper we present another statistical method which has been successful in achieving a reasonable answer where the VTM method has failed. In the new method, one less parameter is derived from material-balance computations. It is assumed that values can be established for effective compressibility in the aquifer and reservoir water saturation independently of the material-balance calculation. The water-influx constant can then be obtained from these data and the quantity of hydrocarbon in place.

By P. Greenfield, P. A. Beck

The phase is a hard and extremely brittle material with a tetragonal crystal structure, containing 30 atoms per unit cell&apos; It occurs in many binary and ternary alloys of the transition elements. The existence of twelve a phases has been reported in binary alloys of metals from the group vanadium, chromium, molybdenum, and tungsten with metals from the group manganese, iron, cobalt, and nickel. It is a characteristic fact that the composition of the o- phases in the various binary systems is not the same. Rather, there is a gradual shift in composition, for instance in the series of chromium a phases, approximately as follows: CrMn,, FeCr, Cr3Co,. In recent years several ideas have been put forward to account for this variability of composition. SullyZ proposed that a was a type of electron compound, characterized by 1.7 electrons per atom in excess of the number required to fill the Pauling atomic orbitals. These excess electrons were supposed to just fill the first Brillouin zone of the u structure. However, later work indicated that the phase is ferromagnetic at low temperatures, so that a- is unlikely to be a full zone compound.~ Another proposal,* which is also based on the structure of the transition elements advanced by Pauling, and in fact leads to essentially the same a compositions as Sully&apos;s theory, suggests that the u phase is characterized by a constant number of electron vacancies per atom. The electron vacancy numbers N,. used were originally the same as those in the Pauling theory, but were later modified empirically vn order to bring about better agreement with data for the p phase in certain ternary systems. For alloys, N,, was calculated on the assumption of simple additivity from the electron vacancy numbers of the components, as follows: N,. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2 (Fe) + 1.71 (Co) + 1.6 (Ni). On this basis a reasonably constant value of N, = 3.4 was obtained for all of the binary u phases and a fairly constant value of N,, = 3.1 for the various p phases. More recently, Bloom and Granta pointed out that a similar correlation with the total number of 3d and 4s electrons per atom is also fairly well fulfilled and concluded that no reference need be made to the Pauling theory. This proposal does not lead to the same binary a compositions as the one described above, so that the relative merits of the two proposals may be determined on the basis of direct comparison with experimental composition data. The purpose of the present paper is to provide such a comparison. Since the experimental data for the composition ranges of several of the known u phases were rather incomplete, it was decided to carry out new experimental determinations for many of the binary systems. Experimental Procedure The alloys were prepared by induction melting in recrystallized alumina crucibles, either in vacuum or in helium atmospheres. Some aluminum was picked up from the crucibles in the alloys of high vanadium content, but this was minimized by keeping the alloys in the molten state for as short a time as possible. The maximum aluminum impurity was 0.13 wt pct by chemical analysis, in an alloy containing over 50 wt pct V. In general, the as-melted compositions agreed accurately with those obtained by chemical analysis. In the case of manganese, however, losses inevitably occurred; consequently all manganese alloys were analyzed. Specimens of all alloys were annealed at temperatures ranging from 1000" to 1300°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. All manganese alloys were sealed in quartz tubes under vacuum before annealing. The specimens were held at temperature for between four and eight days before being quenched into cold water. Alloys were prepared for microscopic examination by mechanical polishing, usually followed by electrolytic etching. X-ray diffraction specimens were prepared by crushing the homogenized alloys, and by reanneal-ing the obtained powders in evacuated quartz tubes for a few hours at the temperature of the lump anneal. X-ray diffraction patterns were made with unfiltered chromium radiation, using an asymmetrical focusing camera of high dispersion. Using microscopic and X-ray techniques jointly, the accuracy

Jan 1, 1955

By W. C. Maurer

A study of bit-tooth penetration, or crater forniation. under simulated borehole condirions has been made. Pressure conditions existing when drilling with air, water and mud have been sirnulated for depths of 0 to 20.000 ft. These crater tests showed that a threshold bit-tooth force must he exceeded before a crater is .formed. This thresh old force increased with both tooth dullness and diflerenrial pressure between the borehole and formalion fluids. At low differential pressures, the craters formed in a brittle manner and the cuttings were easily removed. At high differenlial pressures, the cunings were firmly held in the craters and the craters were formed by a pseudoplas-tic mechanism. With constant farce of 6,500 16 applied to the bit reeth, an increase in differential pressure (sitnulated mud drilling) from 0 to 5,000 psi reduced the crater volumes by 90 per cent. A comparable increase in hydrostatic fluid pressure (simulated water drilling) produced only a 50 per cent decrease in volutne while changes in overburden pressure (simulated air drilling) had no detectable effect on crater volume. Crater tests in unconsolidated sand subjected to differential pressure showed that high friction was present in the sand at high pressures. Similar friction belween the cuttings in craters produces the transition from brittle to pseudo plastic craters. INTRODUCTION The number of wells drilled below 15,000 ft increased from 5 in 1950 to 308 in 1964. Associated with these deep wells are low drilling rates and high costs. High bottom-hole pressures produce low drilling rates by increasing rock strength and by creating bottom-hole cleaning problems. This paper describes an experimental investigation of crater formation under bottom-hole conditions simulating air, water and mud drilling. Although numerous investigators have studied bit-tooth penetration (cratering) at atmospheric pressure conditions, only limited work has been done on cratering in rocks subjected to pressures existing in oil wells. Payne and Chippendale2 have studied cratering in rocks subjected to hydrostatic pressure using spherical penetrators. Garner et aLJ conducted crater tests in dry limestone by varying overburden pressure and borehole fluid pressure independently and using atmospheric formation-fluid pressure Gnirk and Cheathem4,5 have studied crater formation in several dry rocks subjected to equal overburden and borehole pressure and atmospheric formotion pressure. Podio and Gray studied the effect of pore fluid viscosity on crater formation using atmospheric borehole and formation-fluid pressurc and varying overburden pressure. Although these studies have provided useful information on crater formation under pressure, they were limited in that the three bottom-hole pressures could not be varied independently and, therefore, that many drilling conditions could not be simulated. The prersure chamber used in this study allowed visual observation of the cratering mechanism and independent control of the borehole, formation and confining pressures. By using different fluids in the chamber, pressure conditions existing in air, water and mud drilling to depths of 20,000 ft were simulated. The mechanisms involved in cratering at these different pressure conditions were studied for teeth of varying dullness and at different loadins rates. High-speed movies (8,000 frames/sec) and closed-circuit television were used to visually study the crater mechanism under pressure. EXPERIMENTAT PROCEDURE PRESSURE CHAMBER The Pressure chamber in Fig. I was used to simulate bottom-hole pressure conditions. This chamber has been pressure-tested to 22,500 psi and is normally operated at pressures up to 15,000 psi. The chamber contains four lucite windows&apos; used for illuminating and observing the crater mechanism under pressurc. A closed-circuit television and a Fastax camera (8,000 frames/sec) have been used in these studies. Cylindrical rock specimens (8-in. diameter X 6-in. long) were subjected to three independently controlled pressures simulating overburden, borehole fluid and formation-fluid pressures. Overburden pressure, which corresponds to the stress induced by the overlying earth mass, was applied by exerting fluid pressure against a rubber sleeve surrounding the rock. Borehole pressure, which is the pressure exerted by the column of mud in the wellbore, was simulated by applying pressure to the fluid overlying the rock in the chamber. Formation pressure was simulated by applying pressure to the water saturating the rock. The borehole and formation pressures were equal except when mud was used in the chamber, in which case the differential pressure between these fluids acted across the mud filter cake.

Jan 1, 1966

By Walter Weeks

THERE is very little useful material in the litera-ture on the construction of manometers, so each experimenter must devise his own instrument. I have experimented for a number of years and have finally built one that is satisfactory. If we are to obtain accurate friction factors in mine-ventilation problems we must use accurate instruments. The most simple and convenient instrument for the mea-surement of small pressures is the inclined manometer or U-tube. By changing the angle at which the tube is set, any desired magnification of the pressure reading may be obtained. The first question in regard to the manometer is: What liquid shall be used? Alcohol, in my opinion, is the best. It does not cling to the glass and it does not attack the rubber tubes. The next problem is the setting of the instrument at the proper angle. One method is illustrated in Fig. 1. The base plate AC is made horizontal by a level bubble. The plate AB, which carries the U-tube, is hinged at A. The angle z which AB makes with the horizontal may be made any value by pinning the end B at the calculated position on the arm CD. Such an instrument may be designed to read directly in inches of water if a liquid of constant specific gravity is used. If the specific gravity varies, a calculation is necessary to convert the reading into inches of water.

Jan 1, 1923

By Charles E. Glass

A steadily growing body of evidence indicates that earthquake ground motions can cause failure of rock slopes that are otherwise stable under static loading conditions. As a result, the economic optimum working slope angle is reduced when earthquake shaking is considered in surface mine design, especially in regions of high seismicity. When designing surface mine slopes to withstand seismic motion it is as important to consider the probability of experiencing various levels of ground shaking as it is to consider the characteristics of the ground motion. For most slope designs, simple probabilistic techniques such as extreme value or maximum likelihood techniques are appropriate. These techniques, however, should be applied in such a way that a probability value is assigned to characteristic ground motion parameters at the mine rather than to nearby earthquake magnitudes. Several techniques have been developed to analyze rock slopes subjected to dynamic loads. Most of these techniques do not adequately account for the ground motion parameters of concern. The best technique appears to be one that utilizes actual earthquake time histories. A simple technique that calculates block displacement for any input accelerogram, using a linear acceleration approximation between time steps, has been developed that accurately accounts for rock block response. Results using this technique indicate that the following factors are important for assessing rock slope stability in earthquake regions:

Jan 1, 1983

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

By T. T. Chen, P. Pint

Based on the mineralogy, phase characteristics and compositions of the smelter feed, the smelter products and the smelter wastes, the sources and distributions of mercury and arsenic in the Afton copper smelter, Kamloops, British Columbia have been determined. Of the total mercury In the feed, approximately 33% is in solid solution in tennantite, 51% is in native copper and 16% occurs as mercurian silver. Arsenic in the feed occurs mainly as tennantite. Under current smelting conditions, 99.6% of the total mercury In the feeds enters the off-gas cleaning system. From this off-gas, about 1% of the total mercury, occurring as dust, is recirculated to the flotation concentrate; 4.6% of the total mercury is contained in SO2 scrubber sludge which is discharged to tailings. Approximately 78% of the total arsenic in the smelter reports in the copper products; 20% is incorporated in the dust and slag which are subsequently recirculated to the mill. Only 1.8% is rejected as scrubber sludge, and less than 0.2% 1s released to the mercury scrubber.

Jan 1, 1984

By Nicholas J. Grant, Ulf Kalling, John Chipman

THE operation of a blast furnace is dependent to an important extent upon the sulphur content of materials charged and the desired limit of sulphur in the product. It has long been known that the blast furnace is the most efficient tool for desulphurization in common use and that this efficiency is associated with the strongly reducing conditions of the hearth and is enhanced by increased basicity and fluidity of the slag. The chemical reactions of desulphurization may be studied from the viewpoint of the ratio of the process or of the final equilibrium conditions. Both kinds of studies contribute to an understanding of the process and both are included here. A simple measure of the desulphurization power of a slag is given by the ratio: Pct sulphur in slag (Pet S) Pct sulphur in metal [Pct S] This ratio was used by Holbrook and Joseph&apos;,&apos; to measure relative desulphurizing powers under controlled laboratory conditions. It was also used by Hatch and Chipman3 as a measure of the equilibrium distribution. For the latter purpose it would be preferable to employ thermodynamic activities rather than percentages, but until very recently this has been impossible for lack of data. Now, thanks to the work of Morris and Williams and Morris and Buehl," the effects of carbon and silicon upon the activity of sulphur in the metal are known. The confirmation of this work and its extension to include the effects of other elements by Sherman and Chipman and by Rosenqvist and Cox&apos; make it possible to calculate the activity of sulphur in pig iron of any composition. Hence it is now possible to use data on the equilibrium distribution of sulphur to find its activity in the liquid slag and to approach an ultimate solution of the thermodynamic aspects of the problem. The rate of transfer of sulphur from metal to slag is the problem of major industrial importance and indeed the principal need for equilibrium data has been as a necessary adjunct to the kinetic studies. The rate of approach to equilibrium under laboratory conditions seems slow compared to the requirements of industrial practice, and it is clear that further laboratory studies of rates are needed. In the research reported below, the items which were investigated were the following: I—The role of mechanical stirring on the approach to equilibrium. 2—The role of MgO in desulphurization as compared to CaO. 3—The role of MnO in desulphurization. 4— The limiting reactions which constitute the slow steps in desulphurization. Experimental Procedure The experimental set-up and procedure previously described by Hatch and Chipman" were essentially followed with several small modifications. The graphite crucible containing the slag and metal charge was altered to provide considerably more active stirring and mixing of the slag and metal in the carbon monoxide atmosphere. For this purpose the crucible was machined to provide two deep cylindrical wells which were interconnected at top and bottom as shown in Fig. 1. A graphite screw with a flat thread and of shallow pitch (4 threads per in.) spinning at 600 to 800 rpm was used to lift the slag and metal over the partition between the two wells and throw them over into the second well, where the metal settled through the slag into the reservoir at the bottom. It was possible to see actual particles of slag and metal being thrown over the partition. In this respect, the stirring was more vigorous than used in the work of Hatch and Chipman. A charge of 400 g of wash metal was first melted, and 20 g of FeS was then added to yield a bath containing 1.65 pct S. Immediately 400 g of slag (as pure mixed oxides) was added and fused. The slag was generally fused in 1 hr * 10 min. Within 30 to 45 min after melting, the temperature was adjusted to 1525"C, and the first slag and metal samples were taken. The slag was picked up on the end of a cold Armco iron rod, whereas the metal was sucked into a silica tube. The wash metal composition was (in percent): 4.29 C; 0.022 S; 0.021 P; 0.38 Si. The slags used were of four fixed starting compositions covering a wide range of acid-base ratios shown in Table I. Deliberate variations in MgO were made in these slags to check the role of MgO in blast-furnace desulphurization. Changes due to additions and reactions were followed by analysis of samples. Additions of Mn and MnO were made to most of the heats to note the role of Mn and MnO on desulphurization. Three heats (62 through 64) were made in an open pot induction crucible (graphite) using a

Jan 1, 1952

By John W. Rushton

What role does maintenance play in the design of a new mineral processing facility? Consider the fact that most new plants never reach design capacity the first year-or the second, third, or fourth years. The fact is, according to data collected from several plants which have started up in the last ten years, mill throughput and equipment availability doesn&apos;t peak, on the average, until the fifth year.

Jan 3, 1978

By T. Egleston

There has alrvays been atheory among those working placer mines that gold is both folind rusty," and becomes so under treatment, hy which they nleun, not that gold becomes coated with oxide: of gold, but that it, is either coated superficially or alloyed with some substsnee which prevents the contact with mercury,and thus precludenthe possibility of amtrlgamation. To such aoiiditions of the

Jan 1, 1881

By D. G. Westlake

Resistance was measured as a function of temperature, 77° to 350°K,for niobium with hydrogen concentrations up to 3.76 at. pct. Cooling curves exhibited a discontinuity in slope that was attributed to the initiation of hydride formation. A thermal hysteresis was explained in terms of diffusion and the effects of mechanical constraint on nucleation and growth. The heat of solution of hydrogen in saturated Nb-H solid solution was 2. 737 * 0.045 kcal per g-atom, including an unknown stress contribution. The critical ternperatures for hydride formation during cooling and for embrittlement are correlated but not coincident. This, too, has been explained in terms of mechanical constraint and stress-itlduced tratzsfomtation. Nb-H alloys undergo a ductile-brittle transition with decreasing temperature.&apos;-3 Similar behavior has been noted for v-H.1,5 For the latter system, there is evi-dence6 suggesting coincidence of the temperature of minimum ductility and the critical temperature T, for initiation of metal hydride precipitation during cooling. A decrease in ductility due to the presence of brittle hydride particles is readily explainable. The fact that ductility begins to decrease at some temperature higher than T,4,5 has led us6 to suggest that precipitation may be strain-induced locally during tensile testing. Wood and Daniels&apos; have reported that a plot of temperatures for 10 pct reduction in ductility vs hydrogen concentration in niobium is not coincident with, but parallels, the solvus.7,8 They believe this indicates a correlation of precipitation and embrittlement. Unfortunately, the two reported solvuses 7,8 to which Wood and Daniels refer are not in agreement with each other. Furthermore, neither solvus was determined experimentally: each was a plot of calculated solubilities. Thus. neither is highly dependable for determining whether embrittlement coincides with initiation of hydride precipitation. Longson 9 studied phase relations in the Nb-H system between 77° and 473°K by dilatometry. Comparison with metallographic observations convinced him that discontinuities in the slopes of his dilatometric plots were coincident with the initiation of hydride precipitation. Plotting the logarithm of the hydrogen concentration vs the reciprocal of the temperature at which precipitation was initiated during cooling, he obtained a straight line shown in Fig. 1. Walter and chandler,&apos;&apos; using X-ray techniques to detect the for mation of a second phase? have obtained three experimental points in the temperature range 295° to 338°K which fall within Longson&apos;s experimental error for this plot. A similar plotg of temperatures at which dissolution was completed during heating was a parallel line shifted toward higher temperatures. A straight-line plot was obtained, also, for the temperatures of the ductile-brittle transitions,9 but it was shifted toward still higher temperatures. Longson calculated an activation energy of 2.980 * 0.300 kcal per mole for the hydrogen embrittlement mechanism, compared with 3.180 * 0.400 kcal per mole for hydride formation. Despite this agreement, he concluded, "It seems unlikely that embrittlement results from hydride formation..." because hydrogen embrittlement was observed at temperatures above the solvus. It is our contention that embrittlement is correlated with precipitation of the hydride.6 Because only Longson has investigated Nb-H phase relations at sub-ambient temperatures, we deemed it advisable to re-determine the temperature dependence of the solubility using the resistometric technique already proven successful for the V-H system.6 Coincidence of our solvus with temperatures for embrittlement would

Jan 1, 1970

By G. Wranglen

On account of the possibility of isolating carbides in steel it is generally assumed that the electrode potential of iron carbide is more noble than that of ferrite.1,2,3,4,5 Differences from 0.032 V1 to 0.4 V4 have been recorded. However, it is important to realize that the more noble behavior of cementite in relation to ferrite is not an issue of thermodynamics but of reaction kinetics. Theoretically, cementite is less noble than ferrite, which is a direct consequence of its thermo-dynamic instability. With the value ?F°298 = +4700 cal per mol for the free energy of formation of cementite6 it is easily calculated that the electrode

Jan 1, 1950

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400&apos; to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report&apos; with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese; they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way; there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution began. In the 1850s, miners began experimenting with liquid nitroglycerine on a limited scale. This was a very sensitive and dangerous explosive. Fortunately in the 1860s, Alfred Nobel succeeded in stabilizing nitroglycerine by absorbing it in kieselguhr-and a new product, dynamite, was born. With it, miners were able to unleash the great energy of nitroglycerine for blasting purposes. But dynamite was still a very sensitive explosive. In subsequent years, other explosives of various strengths and characteristics were developed, such as blasting gelatin, gelatin dynamite, ammonia dynamites, (all containing some nitroglycerine or nitrostarch), and liquid oxygen explosives. These products and their variations supplied the blasting trade for many years. A grained ammonium nitrate product containing some carbonaceous material entered the market in the 1930s. This explosive had below-zero sensitivity-meaning: a No. 6 blasting cap imbedded in it would not detonate it. A more sensitive initiator, called a primer, was needed to detonate this mixture. From Rags to Primacord to Solid-State The first initiator for an explosive charge was probably a rag slowly burning its way to the charge; this method was quite unreliable. Then came the burning fuse, which was an improvement. Next was the nonelectric blasting cap initiated by a fuse. With these initiators, a miner needed quick reflexes and good legs; upon lighting the fuse, he had to run immediately for cover. Development of the electric blasting cap that allowed for accurate timing eliminated this hazard; the electric cap, however, introduced other safety problems because of its susceptibility to extraneous electricity, e.g., ground currents, lightning, and static electricity. These caps also became available in millisecond delays. Development in the mid-1930s of Primacord, a detonating fuse insensitive to electrical currents or impact, further reduced blasting hazards, and is generally acknowledged as the safest known means of initiation. Eventually, Primacord millisecond connectors also became available for delay patterns in blasting. In the mid-1960s, the Primadet delay was introduced; it is a practical nonelectric detonator system that offers the precise timing of electric blasting caps-and is immune to the hazards or effects of extraneous electricity. Recently, Research Energy of Ohio, Inc. introduced a new type of solid-state blasting machine that combines a sequential timer and delay caps. It enables the efficient breakage of rock with a minimum amount of shock, ground vibration, and noise. Improvements in Blast-Hole Drilling World War II created an enormous demand for coal and other minerals in the U.S. and elsewhere. Great efforts and large amounts of capital were spent to find new mineral deposits and develop better mining methods. But while mechanization in mining proceeded at a rapid pace particularly in open-cut work, there was a definite lag in developing new or improved machines for drilling blast holes. The industry continued to depend largely on horizontal, churn, and pneumatic drills. No better machine was available for large scale production. The need for improvement in this phase of mining became more acute in the post-war years. Despite efforts toward further mechanization, mining costs rose rapidly because of mounting inflation and increasingly high wages. In most operations, drilling and blasting the overburden became the principal item of cost. Therefore, whatever size holes were being drilled, the holes had to be spaced so that any foot of the bore hole could be loaded with the maximum load required for the number of cubic yards of material that each foot of the hole was carrying. With the smaller holes that were being drilled, the proportion of drilling cost to the total drilling and shooting cost was much higher than it would have been with larger holes (because of the closer spacing required by smal-

Jan 1, 1977

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

By Andrew Hyslop

In our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber-tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys- tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1949

By Andrew Hyslop

IN our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys¬tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1948