Search Documents

By J. T., Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas on the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has- also developed very rapidly recently and the various processes to which metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles.

Jan 1, 1927

By H. J. Rahilly

MINE FIRES, in the Butte District, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the top of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "Horsetail Ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 2, 1922

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By A. H. Daane, A. S. Wilson

The U-Cr system is of the simple eutectic type with some solid solubility of chromium in r and ß uranium. The eutectic occurs at 20 atomic pet Cr and melts at 859°C. The maximum solubility of chromium in y uranium is 4 atomic pet at the eutectic temperature, and in ß uranium the solubility is estimated to be 1 atomic pet. y-ß and ß-a transformations were found to occur at 737°estimatedt° and 612°C respectively. DURING 1944 and 1945, the U-Cr constitution diagram was studied in this laboratory as a part of a research program on uranium metallurgy in the Manhattan Project, and the work was described in a Manhattan Project report issued in December 1945. This paper is based on that report, which has been declassified. Prior to this study, it had been shown by other Manhattan Project workers that the low Cr-U alloys could be quenched to retain the form of uranium. Experimental The uranium used in this work was massive metal prepared in this laboratory and contained less than 0.1 pct of other elements. The chromium was 200 mesh powder obtained from the A. D. McKay Co. and was found on analysis to be 99.5 pct Cr with 0.3 pct Fe the major impurity. Alloys, weighing 400 to 600 g, were prepared by induction heating the components to 1700°C in slip-cast ZrO, crucibles in a vacuum of 3x103 mm Hg. TO prevent too violent agitation of the melt by the induction field with subsequent crucible breakage and sample loss, the ZrO2 crucible was placed in a graphite crucible, which was surrounded by a layer of powdered carbon insulation 2 to 3 cm thick. Polished vertical sections of the alloys were examined microscopically to confirm their homogeneity. Heating and cooling curves were taken on the alloys by reheating them in ZrO, crucibles to 1200°C and inserting a mullite-protected chromel-alumel thermocouple into the melt by means of a slip seal in the vacuum head of the furnace. A recording potentiometer traced the curves which had a slope of from 3" to 6" per min. Samples of the alloys were prepared for metallo-graphic examination by conventional mechanical polishing techniques followed by an electrolytic polish in an ethylene glycol-phosphoric acid-ethyl alcohol bath. The structure of the alloys was brought out clearly by this procedure so that no further etching was required. Samples for chemical analysis were taken from drillings from the top, center, and bottom sections of the alloys. The uranium was determined by titra-tion with Ce(SO1)2, while the chromium was titrated with FeSO,; the uranium and chromium totaled at least 99.6 pct in all of the alloys prepared. X-ray samples were prepared by filing bulk specimens in a helium-filled glove box and annealing the resulting powder in a zirconium-gettered helium atmosphere. A 114.6 mm diam Debye-Scherrer camera and a Weyland nonsymmetrical self-focusing camera were used with filtered copper radiation to obtain the powder X-ray diffraction data. Results The data obtained in this study have been combined to construct the constitution diagram of the U-Cr system shown in Fig. 1 where the arrests observed in cooling curves are indicated by dots. The liquidus arrest was quite distinct in thermal data taken on alloys in the range 0 to 20 atomic pct Cr. The eutectic arrest was not observed in studies on the 2.5 and 4.5 pct Cr samples but appeared in the 7.5 pct samples, which suggested some solubility of chromium in y uranium. On quenching from 859 °C, the 2.5 pct sample showed but one phase while the 4.5 pct sample contained a small amount of the eutectic along the grain boundaries; see Figs. 2 and 3. From this the maximum solubility of chromium in r uranium has been set at 4 pct. X-ray studies on these samples showed that the r phase was not retained at room temperature by quenching, but in each case a pattern was observed .which has been identified with the ß phase of uranium. Thermal data show the y-ß transformation of uranium lowered to 737°C as a consequence of this solubility. On quenching from the ß range (660°C), precipitation of chromium in the primary uranium is observed in the 2.5 and 4.5 pct Cr samples (see Figs. 4 and 5),

Jan 1, 1956

By Cyril Smith

SEVERAL investigators, mainly concerned with the mechanical proper-ties of the alloys, have studied the so-called aluminum bronzes after various quenching and reheating treatments. Of these works, perhaps the most complete is that of Bouldoires,1 who studied changes of length, electrical conductivity, thermoelectric force, hardness and micro-structure oh tempering quenched alloys containing 5 to 20 per cent of aluminum, although the work of Carpenter and Edwards,2 Curry,3 Greenwood,4 Braesco,5 Matsuda;6,7 Grard8 and others has added much to our knowledge of the changes occurring during tempering. The so-called acicular ß decomposes on tempering at temperatures between 350° C. and the eutectoid, giving rise to a Widmanstätten structure of a needles in a matrix of d or fine a + d, associated with an increase in hardness and almost complete loss of ductility. Matsuda, studied the' eutectoid transformation by means of dilatation and electrical "conductivity measurements during cooling at different rates. He found that on cooling at the rate of 10° C. per minute there was a decrease in electrical resistance and in length instead of the usual increase which occurred with slow rates of cooling. On tempering the rapidly cooled samples, the increase commenced at about 400° C. and at 520° C. the resistance and length had reached the equilibrium values. These peculiarities he accounted for as being due to a transitional phase ß' being formed, ß having an electrical resistance and volume less than either ß or a + d.

Jan 1, 1933

The Raymond Memorial Volume, which the Members of the In-stitute have been so anxiously awaiting since the beloved man's death, is nearly ready for publication. It will contain about 45,000 words and some illustrations and a frontispiece portrait. This book promises to fill every expectation of the contributors to the volume and the host of admirers of the genius who so long guided the destiny of the Institute. It will contain one of Doctor Raymond's best stories, entitled "James and Jim;" his famous article on "Job on Mining;" and one of his poems entitled "The Grand Canyon." A biography of Doctor Raymond has been written by his daughter, who is the wife of a member of the Institute. The memorial addresses delivered by Dr. Henry F. Drinker and T. A. Rickard at the annual meeting in New York in 1919 will be included. There will also be very interesting reminiscences by H. M. Howe, A. S. Dwight, C. W. Goodale, R. W. Hunt, Lyman Abbott, J. F. hemp, T. A. Rickard. The volume has been edited by T. A. Rickard, which promises all that can be wished for the volume from a literary standpoint. The edition will he limited so that it is very desirable that orders for this volume be sent in to the Institute as promptly as possible. The price will be $5.00.

Jan 12, 1919

By Frank R. Hunter

INTRODUCTION Scope of Work Tins paper represents the results of an investigation of the presence, amounts, and degree of concentration of heavy minerals found in the pulp of the phosphate flotation plant at Peace Valley, Fla., which is operated by the International Minerals and Chemical Corporation of Chicago. In this paper, heavy minerals are those, excepting collophane, that sink in acetylene tetrabromide with a specific gravity of 2.95. Percentages of heavy minerals at several points of the flowsheet and the species of minerals have been determined. Some information as to the screen size of the minerals has been acquired. Previous Work All previous published reports or investigations of the deposits of heavy minerals in Florida have been limited to present beach sands. The mining operations conducted by the Humphreys Gold Corp. about seven miles east of Jacksonville along an ancient shore line have been described in trade journals, but descriptions of the minerals have been lacking. Commercial grades of ilmenite, zircon, and rutile are produced on a large scale. Papers have been published on heavy minerals found on the Florida beaches.I-6 Location "International's" Peace Valley flotation plant is in south-central Polk County, Fla. about eight miles south of Bartow and along the Atlantic Coast Line Railroad. The mine surrounds the plant and includes about 1500 acres of the phosphatic lands in this area. GEOLOGY General Setting All of the rock underlying the area is almost horizontal. The oldest bed exposed is part of the Hawthorn phosphatic limestone of Miocene age. This outcrops in the stream bed of the Peace River about one mile east of the plant. Elsewhere the Hawthorn is covered except where it has been exposed by mining operations. The Bone Valley formation of Pliocene age, which is the phosphatic stratum extensively mined in this area, unconformably overlies the Hawthorn. Resting unconformably upon the Bone Valley formation are Pleistocene (?) terrace deposits of unconsolidated quartz sand which comprise the overburden of the phosphate ore. Stratigraphy Hawthorn formation: "Bedrock" of the pebble phosphate deposits is a cream to white colored, sandy, dense limestone containing varying amounts of small grains and nodules of collophane. The upper surface of the formation is undulating and irregular showing evidence of former

Jan 1, 1947

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By V. N. Mackiw, D. E. Weir, D. J. I. Evans

The world's largest reserves of nickel are found in lateritic ores. Commercial exploitation has been carried out for almost one hundred years; however, none of the plants currently in operation produce pure nickel but rather ferronickel, matte, impure nickel oxide or mixed sulphide precipitate. Over the past decade Sherritt has studied various processes, including the modified reduction roast-ammonia-ammonium carbonate leach process, for the production of pure nickel powder and briquettes from laterites. Nickel can be reduced to the pure elemental form at elevated temperatures and pressures from impure basic nickel carbonate slurries. Several methods were studied in the development of the process for working up the pregnant leach liquor and basic nickel carbonate to produce feed for the aqueous hydrogen reduction step in which pure nickel powder is produced. This paper is concerned only with the laboratory studies using the basic nickel carbonate slurry reduction procedures.

Jan 1, 1973

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By V. J. Decarlo, J. J. Gilman

POLISHING pure zinc differs somewhat from polishing less reactive metals. The problem is not that of finding a suitable reagent, but rather of producing the polish in such a way that the surface remains polished after it is removed from the polishing bath. In other words., the anodic film that is vital to the polishing mechanism&apos; must be tightly adherent and nonporous. It is usually desirable that it be thin. Polishing solutions consist of proper proportions of an acid and a strong oxidizing agent. In electro-polishing, the external circuit acts as the oxidizing agent. The proportions are critical because the essential surface film must be maintained at approximately constant thickness during the polishing process. In the case of zinc, chiefly two oxidizing agents, chromic and nitric acids, have been used. The simplest polishing reagent is concentrated nitric acid. However, it has certain disadvantages. It tends to pit: an excessive amount of heat is evolved during polishing; and the oxide film that it produces is not very stable, so that the polished sur-

Jan 1, 1957

By H. M. Chance

In almost all coal-fields, the quantity of explosive gases given off by the coal increases as depth is attained, requiring correspondingly enlarged quantities of air to ventilate the workings properly, by diluting and carrying off the gas. Again, with increased depth there is a corresponding increased pressure caused by the weight of the overlying strata. Sandstone or slate, which would form a good roof for a coalbed at a depth of 300 or 400 feet, may be unable to sustain the pressure of 800 or 1000 feet of overlying rock. Hence, in nearly all deep mines, the miner will generally describe the roof as "bad," although the roof-rock may be a firm slate, forming an excellent roof for workings of moderate depth, but unable to stand the pressure resulting from the weight of a great thickness of overlying rock. With increased weight of rock-mass above comes also

Jan 1, 1901

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.&apos; Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By Hiroshi Oikawa, R. G. Blake, A. G. Guy

An equatzon has been derivedfor conveniently calculatzng the couvse of homogenzzation in a three-corviDonent solid solutiorz. The necessary assumptions are that the initial distributions of concentration are sinusoidal and that the four interdiffusion coefficients are constant. Employed in the deriuation were the Laplace transform and the fouter Fourier sine transfovwz. The final equation is shown to be in good agveetnent with the experimental results of Kirkaldyet al. on Cu-Sn-Zn alloys. COMMON boundary conditions for representing physical problems are those of the finite solid and of the infinite solid. Many metallurgical phenomena, however, have the geometrical form of a finite pattern reproduced throughout an infinite solid. Precipitation within a uniform matrix and segregation during solidification are examples. The purpose of this treatment is to show that a convenient and useful mathematical analysis is possible in those cases in which the finite pattern can be approximated by a sine function. The particular topic to be considered here is the elimination of segregation by diffusion, but the mathematical model has applicability in many other areas. It should be recalled that the mathematical solution of a typical problem involving a finite solid, such as diffusion into a thin layer, is quite involved.&apos; Various types of solutions are used depending on the degree of advancement of the diffusion process and on the initial conditions. A step function is the simplest initial condition, but even in this case the general solution has the form of an infinite series. Kirkaldy et a1.2 have

Jan 1, 1968

B. F. TILLSON,* Franklin, N. J.-A preliminary study of this paper did not, in my case, succeed in checking with the shovel dimensions of one of the large shovel manufacturers. I therefore raise a question as to there being some difference in standards used by different manufacturers in regard to the dimensions of the shovels for similar sizes and styles, so it may be rather confusing to some of us when we attempt to use the table in this paper and classify the capacity of the shovels as given here with some that are on the market.

Jan 4, 1919

By J. L. Rodda

A large amount of time has been devoted to the microscopical study of the copper-zinc alloys, emphasis naturally being placed upon the commercially important alloys of the system. Suitable methods are available for microscopically recognizing the two phases richest in copper, Per cent,by weight FIG. 1.-COPPER-ZINC EQUILIBRIUM DIAGRAM. (Frond National Metals Handbook, 1933.) but none appear to have been developed for the positive identification of the other phases. This is, however, accomplished, for the phases normally encountered, by an electrolytic method described in the following pages. Five phases of the copper-zinc diagram (Fig. 1) are considered for the purpose of this paper: the solid solution of zinc in copper, alpha (a); the intermediate phases, beta (ß), gamma (y), and epsilon (e); and the solid solution of copper in zinc, eta (n). Beta prime is not considered a separate

Jan 1, 1936

By Harold H. Haman

In view of Twentieth Century advances in mineral dressing technology, most modern metallurgists would be inclined to class jigging as an early, somewhat primitive, representation of their art. The practice of metallic sulfide concentration by jigging is becoming rare. This is so, in part, because the type of ore amenable to the process is becoming rare. It is appropriate, however, that this symposium recognize that a significant contribution of domestic zinc remains dependent upon coarse preconcentration by jigging, and that the state of the art be described even though the theory and applications are already well delineated in technical literature. One of the few areas still using jigging as a major concentrating process is The Upper Mississippi Valley. AREA HISTORY AND JIGGING The Upper Mississippi Valley (UMV) has produced one billion dollars worth of zinc and lead at current prices. The district includes the southwest part of Wisconsin, the northwest corner of Illinois and an adjoining narrow strip of Iowa. Within a total area of 4,000 square miles, important sub-districts cover about 400 square miles. As is widely known, early mining in this district involved shallow lead---crevice deposits of galena that were very selectively mined, hand sorted and cleaned, and then smelted at or near the site. The district has produced almost a million short tons of metallic lead, a very large part of this during the fifty- year period following 1830. Zinc mining began at the end of the civil war, but at a very low rate until about 1905.

Jan 1, 1970