Search Documents

By Joseph Jensen, F. W. Hertel

Many fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which a field was developed. In contrast thereto, in the Ventura Avenue field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other than the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 it. of oil-bearing zone has been penetrated below this intermediate water—a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater penetration in the zone, the better the well. The error of this assumption became evident as time passed. Other pressing attendant problems requiring consideration also developed. In the spring of 1929, the Associated Oil Co., still having a large undrilled area, adopted a method for developing this land by dividing the oil formation into zones, so as to drill two classes of wells and to prepare for others, if conditions in the future justified or required such action. Wells now completed are considered as permanent completions in the zone or class for which they are drilled, and are not looked on as a ready means for deepening or accepted as a temptation for deepening to get some flush production quickly. Provision has also been made to avoid future water problems. The most striking demonstration resulting from such work is the fact that the top of the structure is far from being the point at which the largest oil recovery is made. Wells on the flank of the structure invariably produce with lower gas-oil ratios and secure much larger oil production. Zoning of Oil Sands The Gosnell shale separates the upper light 50 gravity oil from the lower 30 gravity oil below. As the light oil zone is of practically no importance at present, it is not being exploited. The development pro-

Jan 1, 1931

By Nelson Severinghaus

AS far back as 40 years ago management made the initial steps toward utilizing the large amount of reject marble produced by the dimension stone quarries in sized products. In 1947 the Calcium Products Div. of the Georgia Marble Co. was organized to manufacture crushed, ground, and screened products from Georgia marble.* It became obvious early in operations that salability of any products of this type was determined by several factors: high calcium carbonate content, whiteness, dryness, and cleanness. Because no reject material could consistently meet these specifications, Calcium Products Div. now operates three underground quarries for raw material feed. In underground operations no stripping is required, surface contamination and trash are eliminated, weather causes no operational difficulties, and the raw material is maintained dry for plant processing.

Jan 12, 1957

By Frederick J. McGarry, Parviz F. Rad

Although tunneling machines have attained very high advance rates in medium-hard rocks, the need for frequent repairs has slowed their use in very hard rocks. Laser- assisted tunneling is expected to improve tunneling machine performance by improving either specific energy or amount and quality of muck. The beneficial effects of lasing are the initiation and growth of microcracks from differential thermal expansion of grains, and overall spalling in the vicinity of the lased area. Using a constant thrust rock cutting device with disk cutters, the effects of cutter geometry, cutter diameter, thrust, and speed variations on specific energy and muck were explored and the improvement in performance of disk cutters caused by lasing was evaluated. It was found that the improvement depends on beam power and density, beam speed, pattern of heating, and cutting pattern and procedure. A focused beam slightly offset from the cutter path gives the most improvement both when cutting on a smooth surface and when cutting in previously cut grooves.

Jan 1, 1971

By R. W. Raymond

ChaRles William HenRy Kirchhoff was born March 28, 1853, at San Francisco, Cal., where his father, Charles Kirchhoff, was at that time consul for his native country, Germany. A few years later, the family moved' to Hoboken, K. J., in which city the son received his preliminary education at the Hoboken Academy, proceeding later to Germany, where he was graduated in 1874 as mining engineer and metallurgist at the Prussian Royal Mining Academy of Clausthal, in the Harz. Upon his return to the United States, he became chemist of the Delaware Lead Refinery at Philadelphia, and retained that position for three years. But in 1877 he began what was to be an almost uninterrupted life-long association with David Williams, the publisher of The Iron Age, of New York, who established in that year, and continued for a brief period, a journal entitled the Metallurgical Review, on the editorial staff of which Mr. Kirchhoff received a place. The enterprise was doubtless an attempt to cover a wide metallurgical field outside of that which properly belonged to The Iron Age. But it was soon abandoned, and Mr. Williams wisely concentrated his energies upon the older journal, which, under his vigorous and skillful management, and the labors of the able editors and correspondents whom he selected, became one of the greatest institutions of its class in the world. From 1878 to 1881, Mr. Kirchhoff was assistant editor of The Iron Age. From 1881 to 1884, he was managing editor of the Engineering and Mining Journal; in 1884 he returned to The Iron Age, to become for five years its associate editor, and in 1889, on the retirement of James C. Bayles, editor-in-chief. This list of dates and employments, without further comment, sufficiently indicates, at least to the eye of an expert, that Mr. Kirchhoff had found his congenial career in trade journalism. His qualifications for this profession were somewhat exceptional. He possessed the scientific training, the knowledge of foreign languages and literatures, and the power of making and keeping friends, which enabled him to get early notice of technical novelties; he had the taste for statistics which made him both industrious and intelligent in their collection and use; and to these traits he added a mastery of the meaning of such accumulated data, and a sane, critical judgment of the situations which they represented, as well as of the sources and the figures themselves, which made his opinion weighty

Jan 1, 1917

Every 12 minutes, a cable operated skip car appears from beneath the desert surface of Arizona's Papago Indian Reservation. The Papagos have become quite used to the car, particularly those whose paychecks depend upon its regular appearance. The 24-ton capacity skip or tramcar hauls copper ore out of the North Decline of Hecla Mining Company's new mine about 30 mi south of Casa Grande. While there's nothing particularly glamorous about the skip itself, the railroad system upon which it travels is interesting because of the unconventional way it was built.

Jan 6, 1974

By H. A. Wentworth

The Huff electrostatic plant of the United States Smelting CO., operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. , In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some rearrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely from the company's mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing, and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company's own mines, the results given below are fairly indicative of the general work obtained. The diagram, Fig. 1, illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill, containing from 15 to 18 per cent. moisture, is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 1, 1915

E. A. HOLBROOK,*Urbana, Ill.-To those who have followed the development of powdered coal two questions often occur. First, as to the moisture in the coal. In Illinois we recognize that the bituminous coals contain about 12 to 15 per cent. of what we call "contained moisture," that is, the moisture is present in the coal although this may appear absolutely dry and dusty. In addition, the surface moisture may be present in any amount. I would like to ask what is the relative effect of these two forms of moisture upon the work of pulverizing. Does Mr. Collins refer to the contained moisture or to the surface moisture in estimating the degree to which the coal must be dried? H. R. COLLINS.-In the lignite coals, of which this country possesses a great deal and is beginning to develop them to considerable extent, the "contained" or "combined" moisture does not .trouble us; we have no difficulty in reducing lignites to a high degree of fineness. But when dealing with bituminous, sub-bituminous, or semi-bituminous, we, prefer to reduce the combined moisture as well as the hydroscopic moisture as far as possible. We have recently put into operation, at a plant, furnaces and boilers consuming the lignite from northern New Mexico, which contains between 4 and 5 per cent. moisture as we pulverize and burn it. The evaporating efficiencies under the boilers have been so remarkable that we wish to check the results half a dozen times before quoting them. We have also just started two boilers at the Garfield smelter, and have obtained the same high efficiencies.

Jan 11, 1918

By William P. Blake

The copper-beariug rock formations of Cananea, Sonora, Mexico, present conclusive evidences of extensive and sharp plication. Some of these evidences are here briefly stated. 1. There is a succession of approximately parallel outcrops of an altered limestone, alternating with dikes and masses of porphyry. The great copper-ore deposits are in close association with these ridges of limestone, which trend northerly and southerly and stand nearly vertical. This parallel succession is so well-defined that the management of the mines has, for convenience, recognized and named five zones, known from the chief mines, in their succession from east to west, as the " Cobre-Grande," " Veta-Grande," " Esperanza," " Capote," and " Puertocitas " belts. The intervening and separating formations are coarsely crystalline feldspar porphyries, highly basic, of light color, which may be regarded as intrusive and, in part at least, as the cause of the metamorphosed condition of the limestone. 2. These cupriferous limestone-zones are similar in constitution, are similarly charged with copper-ore (in association with quartz as a gangue, or veinstone), and are marked by similar croppiugs of gossan. 3. Distinctly folded outcrops of the surrounding strata can be observed, especially on the eastern border of the copper-bearing district north of the Democrita ground, and not far from the Veta-Grande. 4. The limestone ridge adjoining the Veta-Grande ends a short distance north of the mine, and appears to be the extretne end of a synclinal trough. 5. The Capote limestone, the most western of the croppings of the central copper-bearing area, is contiguous to stratified sandstones and quartzites, uplifted at high angles, but showing an easterly dip. The Capote limestone is apparently conformable

Jan 1, 1905

By B. B. Betty

H. L. Burghoff.*—Have the authors any information on the effect of grain size in these materials? There is a material difference in the grain sizes shown for the Monel and the Inconel. Is a wide range of grain size normally found for each material, and, if so, what is its effect upon creep strength? 11. L. Eiselstein.—The grain size for Monel shown in the micrograph is the usual size found in that product. The grain size of Inconel is about the same as that, too. However, we have run tests on Inconel at higher temperatures than those reported in this paper, and have found that the coarser grain size has a better creep resistance; and that the grain size that gives the best creep resistance at 1600°F. is about 0.005 in. in diameter. We have no test on Monel with varying grain size. J. J. KANTER.†-It has been known for a long time that Monel metal exhibits ductility anomalies at elevated temperatures. Even in short-time test, it can be demonstrated in the range of 900°F. that there is a distinct falling off of the ability of Mone1 metal to elongate, and in rupture tests this shortcoming is still further accentuated. Knowledge of this rupture anomaly of Monel metal may be one of the reasons for which designer's approach certain high-temperature applications with reservations. The authors of this paper have merely demonstrated that for 900°F. the alloy has an ability to elongate 1.7 per cent over a period of some 2700 hr. Before any conviction can be expected from designers that Monel metal is applicable to stress design in such range of temperature, I think it is desirable to demonstrate the capacity for the material to elongate over a longer period of time than has been done in this presentation.

Jan 1, 1945

By Clair Upthegrove, E. S. Rowland

The widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the stronges nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-A1 and Cu-Zn, among others, exhibit promising improrcmc~nts in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those reahzed from the binary copper-beryllium alloys, excellent properties arc obtaincd with beryllium contents averagirlg about one-half the amount reqnired in the binary alloys. This paper presents the results of an investigation of the equilibriun relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of quenching experiments, microscopic examination and thermal analysis The results of some powder-method X-ray determiniations on the alloys, conducted by Mr. William Mikulas and Prof. Lars Thomassen at the University of Michigan, are used as evidence in this paper. The con

Jan 1, 1935

By E. S. Rowland, Clair Upthegrove

The widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the stronges nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-A1 and Cu-Zn, among others, exhibit promising improrcmc~nts in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those reahzed from the binary copper-beryllium alloys, excellent properties arc obtaincd with beryllium contents averagirlg about one-half the amount reqnired in the binary alloys. This paper presents the results of an investigation of the equilibriun relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of quenching experiments, microscopic examination and thermal analysis The results of some powder-method X-ray determiniations on the alloys, conducted by Mr. William Mikulas and Prof. Lars Thomassen at the University of Michigan, are used as evidence in this paper. The con

Jan 1, 1935

By R. H. Walpole, J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger ecorlomic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic. As with any mechanical devices, selection of suitable dust collector equipment involves evaluation of available products with characteristics most nearly meeting conditions of the application at hand. When there is valuable product to be collected, and/or when there are possibilities of air pollution or public nuisance, collector selection is often guided by the maxim of "highest available collection efficiency at reasonable cost and reasonable maintenance." A brief review of dust collector designs will permit outlining of major characteristics of each group. Final selection will involve detailed data against a background of the problem under consideration. The dry centrifugal collectors, see Fig. 1, represent a group of low cost units with minimum maintenance. They are subject to abrasion under heavy abrasive dust loads and to plugging with moist materials. Efficiency drops off rapidly on particle sizes below the 10 to 20 micron group. Because of the large amounts of —10 micron particles in most mining dust problems, they will normally be used as primary collectors and will be followed by high efficiency units. This combination is cspecially popular where the bulk of material is desired in a dry state with wet collection indicated for the final cleanup portion. In remote plant locations, dry centrifugal~ can be used alone if product in dust form has no value or if dust loading is light enough to eliminate a nuisance in the plant area. Where high efficiency dust colleotion equipment must be selected, choice will normally involve fabric arresters, wet collectors, or high voltage Electro-Static precip-itators. Fabric arresters, see Fig. 2, rely on the passing of dust-laden air at low velocity through filter fabric. Velocity ranges from 1 to 3 fpm for the usual installation and may be as high as 10 to 20 fpm in arrangements where automatic frequent vibration or continuous cleaning of the filter media is employed. Fabric is normally suspended in either stocking type or in an enlvelope shape. Collection efficiency is excellent even on sub-micron particle sizes. Equipment is bulky, must be vibrated to remove the collected dust load, and is restricted in applications from temperature and moisture standpoints. Condensation of moisture on the fabric filter mcdia causes plugging of the passages with great reduction in air flow. Temperatures for the usual medias of cotton or wool are 180" and 200°F maximum, although the introduction of synthetic materials such as nylon, orlon, and glass cloth have increased the possibilities of this type of collector for higher temperature applications. The wet-type collector may employ a number of different principles so that entering dust particles in the gas stream are wetted and removed. Principles usually include impingement on collector surface or water droplets, often in combination with centrifugal forces. Variety of wet collector designs is indicated by typical collectors illustrated in Figs. 3 and 4. Collection efficiency is a function of the particular design, although the better collectors will have high collection efficiency on particles in the 1-micron range. Wet collectors have the advantage of handling hot or moist gases, take up small space, and eliminate secondary dust problems during the disposal of the material. At times collection of the material wet is a disadvantage. Wet collectors may also be subject to corrosion and freezing factors. The high voltage Electro-Static precipitator, see Fig. 5, is probably the most expensive type of high efficiency collector. It finds its applications generally in problems in which collectors previously discussed cannot be employed. Its collection efficiency is based on its design features and can be excellent on the finest of fume particles. Material is normally collected dry. Gas temperatures are of no great concern as long as condensation does not occur within the dry type of precipitator and the temperatures do not exceed the limits for materials used in its construction. As with the fabric arrester, provisions

Jan 1, 1954

By Fred Wise

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed, The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxi-dized, The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices, On this basis metallurgical results are viewed in the light of an optimum tailing rather than a per-centage of extraction.

Jan 1, 1940

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By R. E., Head

THE use of lime in flotation has become so general in recent years that its functions are familiar to plant operators. The conditions and phenomena described in this paper are of interest because they are directly associated with the use of lime as a reagent and the resulting formation of lime scale worth nearly $1 per pound for its gold content. It is not known to what extent lime scale is common in flotation plants where lime is used, but as several occurrences have been re- ported, its existence is not limited to one particular plant. In November, 1927, the author's attention was drawn to a lime scale that formed on the sides of Callow flotation cells in the Walker Mining Co. mill at Spring Gar- den, Cal. The scale was described as an accumulation of hard material that built up on the sides of both the rougher and cleaner cells and in some instances attained a thickness of 2 in. The lime scale builds up in the cleaner cell at the rate of about 1/10 in. per month, or slightly more than ?12 in. during six months' operation. The rate of growth in the rougher cells is slower, and about 3/s in. of scale forms in six months. Analyses' of typical lime scale samples are as follows:

Jan 1, 1928

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or: more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud.

Jan 1, 1949

By Paul Billingsley

THE mining districts of the first and second order1 of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of Tertiary compres-sive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 NATURE OF THE THRUST ARC The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The cross-sections are as shown in Fig. 2.

Jan 1, 1933

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By T. F. Baily

DURING the period of the War, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the FIG. 1.-EXPERIMENTAL FURNACE. 5000 KW. CAPACITY: 150 TONS 2 PER CENT. SILICON PIG IRON PER DAY. electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted at Canton, Ohio, in

Jan 1, 1930

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with rare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930