Search Documents

By Joseph T. Roy

MINING revival during the last few years has brought about a considerable increase in the number of gold and silver determinations made, noticeable in all branches of the industry but especially so in the business of a custom smelter. At East Helena, solely a custom smelter the assay department found that the four assay furnaces available were inadequate to handle the increased amount of work. These furnaces were of a standard design, having duplex muffles, one superimposed on the other; each muffle was 12 1/2 in. wide, 18 1/4 in. long and 6 in. high, and could handle 72 cupels or 20 fusions. Since the heat varied considerably between the upper and lower muffles, cupellations were not ruin in both at the same time. To speed up assaying, E. A. Meale, chief chemist, had the happy idea of enlarging a muffle furnace, originally designed by the Montana Power Co., so that one muffle would acconmmodate at least as many determinations as the duplex muffles. An order was given to the Denver Fire Clay Co. for a Carbofrax muffle of the size required and the local engineering department enlarged the furnace to accommodate the muffle. Details of the

Jan 1, 1938

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By A. J. Weinig

IN the accompanying figure consider the classified AB in closed circuit with a ball mill, wherein T = Tonnage of new feed C = Ratio of circulating load Now consider that the circulating load is made up of two portions of ore. One portion is due entirely to the characteristics of the ball mill and the tonnage of new feed impressed on the ball mill. This portion of the circulating load in no way is to be blamed on the characteristics of the classifier and is all composed of oversize. Consider, for illustration, that this portion of the circulating load is handled in the A division of the classifier, assuming that the classifier is divided longitudinally into two divisions by an imaginary line. Because the classifier does not usually make a perfect separation of the undersize, a certain portion of the total circulating load is to be directly blamed on the efficiency of the classifier. Let this portion of the circulating load be considered as being handled in the B division of the classifier. Now if the classifier is operating perfectly (100 per cent efficient), the width due to the B division becomes zero and correspondingly the efficiency of the classifier diminishes as B becomes wider in proportion to A. If E is the mechanical efficiency, then

Jan 1, 1934

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928

By Nathaniel Herz

PARTING of bullion before shipment to the mint had been considered by the Homestake Mining Co. at various times, but had never been attempted before 1933, be- cause the margin of profit appeared to be too small to warrant the complications in refining. When the gold standard was abandoned by the United States in the spring of 1933, however, parting of the bullion was decided upon. The method selected was the Miller or chlorine process, which consists of the passing of gaseous chlorine into a bath of molten bullion, converting all metals other than gold into chlorides, and remov-

Jan 1, 1935

By Thomas H. Sheldon

IN the zeal for opening up new ore-bodies, or for. extracting the ore from attractive bodies gal ready opened up, we very often lose sight of the fact, that, after all, the operation of a mine is a business proposition, pure and simple; and for the best working-results should be treated upon a strict business basis. Of course, in every mine of consequence a record is kept of expenditures and receipts, and such glittering generalities as "gross receipts," " net receipts," " mining expenses," .and " per cent. profit," can be told to the cent; but does this . record show economy of management, either as compared with the same record of other months, or as compared to the record of other mines of the' same class ? Moreover, if such a record shows that the cost of mining is high, does it in any way en¬able the manager to put his finger on the leakage? Does it necessarily follow that a mine which makes a profit of, say, 40 per cent on 25-dollar ore, is doing less economical mining than one which saves 60 per cent on 80-dollar ore ? Of course the figures in the latter case look the more attractive, but when it comes to a point of saving everything which can be saved, and of cutting down expenses to the lowest possible cost of operation, the former mine is doubtless on the most firm and economical financial basis. But as the relative merits of the system of mining in the two cases, nothing could be decided without a basis of detailed comparison ; if one system is more economical than the other, why is it so, and wherein does the advantage lie ? This can be shown only by keeping accurately the cost of each mining operation. And no matter how dissimilar two mines may be in character and operation, yet there are a few general heads common to all mining operations. In the first place, it is necessary to break the ore from the solid ground ;

Nov 1, 1905

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

The Cuajone and Toquepala copper projects are located in the extreme southern area of Peru. Since 1960, Southern Peru Copper Company has operated the Toquepala open -pit mine, flotation mill, 110 smelter, townsites, power plants, and railroad. Toquepala and 10, the smelter and port location, are connected by a 110-mile-long (176 lun) railroad. Much of Toquepala's infrastructure has been used for the Cuajone project. Cuajone, at an elevation of 11,400 ft (3475 m), required five standard-guage railroad tunnels with a combined length of 17 miles (27.2 km) to connect with Toquepala so concentrates could be shipped to the no smelter. The total cost of Cuajone is estimated at $726 million for a designed annual capacity of 180,000 tons of copper, equivalent to about $4,000 per ton of installed production capacity. This relatively low cost per ton, by today's standards, has been made possible through the use of the 110-to Toquepala railroad, the ability to expand the 110 copper smelter, and other favorable factors. To mine the 468 million tons of copper sulfide or e at a grade of 1.0% copper, approximately 24 1 million tons of waste were stripped- before mining of ore to supply the new Botiflaca 45, 000 ton per day concentrator. The mining rate must exceed 300,000 tons of waste plus ore per day to maintain the 45, 0 00 tpd sulfide ore milling rate which was to be reached at the end of 1976. Waste stripping is done with 15 cu yd electric shovels and 120 -ton trucks. Ore mining is done with 8 and 9 yd shovels. A railroad connects the pit with the 60 in. by 89 in. Allis-Chalmers gyratory crusher. Side-dump railroad cars of 50.cu yd capacity dump onto a 0 16 ft 9 in. long (5. 1 m) grizzly inclined at 40º with 7 to 8 in. (178 to 203 rnrn) bar spacings. The grizzly is divided into two 22 ft 4 in. (6.8 m) wide sections and two side -dump railroad cars discharge simultaneously into the 150-ton capacity dump pocket. A Barco rock manipulator is used for breaking or removing oversize from the dump pocket. The bin receiving the grizzly undersize has a capacity of 5,000 tons, and the pocket beneath the crusher holds 900 tons. Each is equipped with an 84 in. apron feeder, which feeds a 60 in. (1.52 m) conveyor belt to the 150,000 ton coarse ore stockpile, where the ore is distributed by a 72 in. (1. 83 m) tripper conveyor. The 45, 000 live tons in the coarse ore stockpile are reclaimed by twelve 48 in. (1. 22 m) apron feeders. Maintenance on the crusher eccentric is made easy by an eccentric

Jan 1, 1978

By W. E. D. Stokes

WHEN history is written, the year of the blitzkrieg will go down as giving aviation its greatest impetus. No perceptible drop in military business, even with cessation of hostilities abroad, seems likely. The combined air force of the U. S. Army and Navy on July 1 was approximately 5000 planes, as against 50,000 planes currently discussed as necessary. Observers at the fronts are giving designers and metallurgists back home some realistic ideas to shoot at. As conventional runways reveal the location of airports to enemy raiders, operating bases are now masked. Difficult, often muddy and rough landing strips, requiring strong landing gears and exacting take-off and maintenance characteristics, are the specifications of war. This is "old stuff" to numerous mining operators in mountainous jungle areas where gradients up to 8 per cent are in more or less common use in such mountain landing fields. Although airplane building is not readily adaptable to assembly-line methods, a trend towards mass productions is now in evidence. Incidentally, a U.S. Army "Curtiss P-40" requires about 10,000 man hours of work to complete and is tied together with 75,000 rivets. During the past year a number of aircraft factories adopted the "shot-

Jan 1, 1941

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By T. B. Gyles

Zinc is made by the National Smelting Co. and its associates by both the horizontal retort process and the vertical retort process developed by the New Jersey Zinc Co. This paper deals only with the horizontal retort practice at Avonmouth. That the horizontal retort process does survive in all countries in some form or other is due to at least partial success in overcoming some of the inherent difficulties of the process. The horizontal retort furnaces ran into considerable difficulties when the product of the selective flotation of mixed lead and zinc ores became the normal material for treatment. It is necessary, therefore, to make some reference in connection with the process to the preliminary treatment of the ore prior to distillation.. Therefore we include some small reference to this aspect in our description. Furnace Design and Structure Of the types of furnaces in operation at the company's various works, those at Avonmouth are perhaps more typical of the trend to utilize large units, with a subsequent saving in costs, such as heating and supervision.

Jan 1, 1937

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By M. J. Coolbaugh

There is a need for concepts and techniques developed specifically for blasting in areas where the rock is loose or highly fractured. Common practice has been to use techniques developed in hard homogeneous rock and reduce the amount and strength of explosive. However, this rule cannot cope with all of the special characteristics of highly fractured rock and has not adequately taken care of the problems of overbreak, gouging, and wall damage. The main problems encountered when blasting in highly fractured rock are controlling the amount of rock broken, minimizing the damage done to the remaining wall material, and adapting blasting methods to rapidly fluctuating ground conditions. In addition, because it frequently needs timber support right into the blasting area, there is also the problem of how not to shoot out the timber when heavy loading is needed in order to offset a loss of impact caused by deflection of the detonation wave off the numerous rock interfaces, and by the absorption of the wave by resilient clay particles. Another consideration is the fact that less attention needs to be directed toward producing satisfactory fragmentation of the broken rock. Those blasting methods designed for breaking hard rock into manageable segments are, as a rule, not needed in highly fractured rock which will usually break along its own numerous fracture lines.

Jan 8, 1965

By HUNTINGTON ADANS

(Wilkes-Barre Meeting, June, 1911.) THE arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving -of time lost in filling and discharging. But in the treatment .of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may, cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift .tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that -of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in ,starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the .arrangement of a continuous flow of pulp from tank to tank,

Aug 1, 1911

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder' showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By ALFRED T. BARR

In certain areas of the New Cornelia pit, considerable secondary blasting is necessary to reduce oversized boulders, formed from primary blasting, to pieces which will pass the 41/2-cu yd dippers on the shovels. Some of the boulders are 'dobied, but when time permits they are blockholed and blasted. In most instances one hole drilled to a depth of 2 to 3 ft and blasted with 1/3 to 1/2 of a stick of powder will break a boulder satisfactorily. Blockholing is normally done by using a jackhammer of the 55-lb class, 1-in. round drill steel, and detachable steel bits, 2-in. gauge when new. A bit change is usually made after the completion of each hole. The use of light drilling equipment in blockholing is desirable, both from the standpoint of safety and ease of doing the work, and when it was seen there was a possibility of using a lighter jackhammer through the use of tungsten-carbide bits and at the same time get at least the same drilling efficiency as with the standard equipment, it was decided to test tungsten-carbide bits. The claims for long life of the bits and footage drilled before resharpening gave hopes of eliminating much of the delay time in changing bits which is unavoidable with the use of steel bits. and thus gain in actual drilling time.

Jan 1, 1949