Search Documents

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

ROBERT M. KEENEY,* Portsmouth, Ohio (written discussion?).- Mr. Coffin has written a most interesting paper that covers most of the uses to which water-cooled devices are subjected; but to meet with the operating department's approval, these devices must effect a saving in cost per ton of ingots produced in the furnace. The making of steel in the open-hearth furnace is dependent entirely on the personal element. It is not possible to charge the furnace with so much raw material, turn on a valve for heat, and by use of recording thermometers, clocks, etc. empty the furnace when a steel is made. Competent men trained to the work must be in charge all the time, and the quality and quantity of steel produced is quite as dependent on the care and working qualities of the furnaces as on the raw material and working of the charge itself. Steel making is hot, hard work and the inducement offered to technical men to take up this work is not sufficient to induce many to enter the field. The result is that most of the workmen in an open-hearth plant, the men who actually operate the furnace and make the steel, are not technical men and do not understand the "whys" and "wherefores " and care less. All this means that a furnace must be built as nearly fool-proof as possible. By this I mean that it is necessary to protect those parts of a furnace most subject to abuse by water-cooled devices whenever possible, and these water-cooled appliances must he as nearly fool-proof as they can be made. The control of the gas entering a furnace is of the utmost importance. This means a properly designed port must have the same design throughout the whole run of the furnace. This is not possible with the ordinary

Jan 6, 1919

By P. K. Currie, J. V. Walters

Solution mining of magnesium salts (Carnallite and Bischofite) is taking place near Veendam, in the northeast Netherlands. The magnesium salts are used for the production of magnesia sinter, used as a base material for the manufacture of refractory bricks for furnaces. This paper gives, first, an introduction to the operational procedure followed in Veendam, with the emphasis on some of the unique aspects, and then discusses rock-mechanical aspects of the cavity behaviour. The creep behaviour of magnesium salts is described, and Finite Element calculations on cavity stability and potential surface subsidence are discussed.

Jan 1, 1985

By Warnie Flint

PERSONAL INJURY ACCIDENTS According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. NO one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who arc living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they arc utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of Knowledge or skill. 2) Conflicting motivations, such as: (a) to be more conformable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, hut not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By J. D. Testerman

A statistical technique to identify and describe naturally occurring zones in a reservoir and to correlate these zones from well to well is described. The technique is particularly useful in describing a reservoir where cross flow between adjacent strata is important in determining reservoir behavior. Although it has been used primarily for permeability zonation, the technique is general and can be used to correlate any reservoir property or related data, such as the information contained in well logs. INTRODUCTION One of the first problems encountered by the reservoir engineer in predicting or interpreting fluid displacement behavior during secondary recovery processes is that of organizing and using the large amount of data available from core analysis. Permeabilities pose particular problems in organization because they usually vary by more than an order of magnitude between different strata. Due to the sheer volume, it is almost always necessary to group data and to use an average value to represent a number of measurements. Perhaps the most common method now used to group permeability data is the capacity-fraction technique, which ranks permeabilities in order of magnitude, regardless of the physical location of the permeabilities within the reservoir. The cumulative per cent capacity is plotted against cumulative per cent thickness. This plot is divided into an arbitrary number of zones, generally of equal thickness. Five zones (or averaged groups of data) usually are obtained, each of which is treated as homogeneous in subsequent calculations. The division so obtained has no physical meaning; strata in the same zone, calculation-wise, are usually not adjacent in the reservoir. Reservoir engineering techniques being developed will handle crossflow that occurs between adjacent communicating reservoir strata because of imbibition and gravity segregation. Since crossflow occurs between physically adjacent layers within the reservoir, a new zonation technique recognizing the actual location of strata within the reservoir is necessary. Similarly, the recognition of natural zones is important for predictions of oil recovery by processes involving diffusion. One such process is miscible displacement, where predictions of lateral diffusion within the reservoir must recognize the actual location of the invaded zones in relation to the rest of the formation. Natural zones must also be adequately recognized to account for heat transfer within the reservoir during thermal exploitation. Because of the complexity of the problem, statistics appear to offer the only practical hope of dividing a reservoir into physically-meaningful natural zones. This paper presents a statistical technique for identifying these natural zones and for ascertaining which ones are likely to be continuous between adjacent wells. The zones defined have minimum variation of permeability internally and a maximum variation between zones. The technique is general and can thus be applied to reservoir properties other than permeability. The method will guide the reservoir engineer in estimating which zones are likely to be continuous between wells. However, a statistical correlation based on permeabilities in two different wells is no guarantee that the zones so defined are, in fact, continuous. Rather, the assumption of continuity must be consistent with geological data concerning the depositional environment, as well as justified on the basis of engineering judgment in combination with statistics, just as judgment is required with conventional zonation methods. CALCULATION PROCEDURE The reservoir zonation technique is a two-step operation. The steps are individually described, and a sample calculation is presented in the Appendix. ZONATION OF INDIVIDUAL WELLS First, the set of permeability data at a single well is zone, into Zones. These zones are selected so that variation is minimized within the zones and maximized between the zones. The equations4,6 used to zone the data are where B = the variance between zones, , = the number of zones, i = the summation index for the number of zones, j = the Sumation index for the number of data within the zone, mi = the number of data in the ith zone, k,. = the mean of the permeability data in the ith zone, k . = the over-all mean of the data in the well, W = the pooled variance within zones, N = the total number of

By E. A. Anderson

IN another paper1 the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 lb. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging.

Jan 1, 1929

By Carl Keuffel

THE manufacture of optical glass is a new industry in this country. In 1914, after the war started, the supply of optical glass from Europe was cut off, but as there was a fairly large stock of glass on hand, it was not until the end of 1915 that the optical instrument makers made serious efforts to produce their own glass. These early attempts were generally made by practical glass men and, due primarily to the fact that very little scientific help was used, the first attempts were unsuccessful. It was not until the whole problem was attacked by technically trained men who used advanced methods of research that good results were obtained. These researches proved that the accurate control of the temperature was a most important factor in the manufacture of optical glass. The early glass maker judged temperatures with his eyes; later, Seger cones were introduced into the furnace at various stages of the melt. Then radiation, indicating and recording pyrometers with rare-metal thermocouples were introduced. Now, in addition to these, an optical pyrometer every hour or so is sighted right into the pot and on the molten glass. Figs. 1 and 2 show how pyrometers are used to control the melt. InFig. 2, Y is the clay pot in which the batch is melted to glass within the furnace X. The rare-metal thermocouple S, protected by a clay tube, extends through the wall and about 4 in. into the furnace. This couple is connected to an indicator T and a recorder U so that a complete record of the furnace temperatures is obtained. The section of the curve ABCD, Fig. 1, shows how gradually and carefully the clay pot must be heated to get rid of moisture AB and during the calcining at CD. The stem of an expansion pyrometer R is extended through a hole in the door Z of the furnace and into the pot in order to more closely follow the temperatures of the clay pot itself during the burning process, that is from A to D. After the pot is calcined, the temperature can be rapidly raised to E (about 1430° C.); from E to F this temperature is much higher

Jan 9, 1919

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By D. D. Homer, R. H. Cromwell

The Minas de Matahambre No. 2 shaft, vertical, four-compartment lined with steel sets and hardwood lagging, has been sunk 2057 ft. On account of rock structure, over-all cross-section dimensions are 23 by 6 ft. Certain sections have been concreted. Two compartments are for handling ore and men, one for supplies and men, and one for manway, cables and counterweight. Two 250-ton capacity skip pockets with air-operated gates and steel cartridge pockets have been installed underground. A steel "A" headframe, a 250-ton steel receiving bin, and skip-to-man-cage changing equipment have been provided. Skip capacity is 102½ cu. ft. The hoist is a Nordberg double-drum 10 ft. by 6 ft. 6 in. geared, electrically driven, with parallel grooving for 1-?in. cables. Maximum hoisting speed is 1600 ft. per minute. The motor-generator set, control panel, slip regulator and hoist accumulator are housed in the basement of the hoist house. The electrical equipment is General Electric. The direct-current hoist motor is 800 hp. Control is of the Ward-Leonard-Ilgner type. The motor-generator flywheel set, normal speed 720 r.p.m., consists of an 800-hp. induction motor, a 22-ton flywheel (dia. 117 in.) and a 650-kw. generator.

Jan 1, 1934

By S. Stutz

COAL, like most other minerals, only exceptionally occurs in a sufficiently pure state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more percent in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but most frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypsum. In both cases the impurities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the, manufacture of iron. Coke will contain on an average at least ;fifty per cent, more ash and sulphur than the raw coal from which it is, made. To the manufacturer of iron every additional per cent. of ash which his coal or .coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight ; that is, a certain part of the coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the-iron-master that coke containing less ash makes the slag or cinder more liquid and less inclined to stick to- the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore and flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etc:, from the coal 'has as yet only been succesafully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By Clamer, G. H.

G. H. CLAMER, * PHILADELPHIA, PA.-Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early clays, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used.. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 12, 1918

By Robert S. Baker

It has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformiation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta) (alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It, is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850" C. in iced brine at -8" C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 35.60 per cent zinc (9812 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1932

By AIME AIME

THE stage is set for the 1930 Annual Meeting. It will take place in the Engineering Societies Building. Feb. 17, 18, 19 and 20, and an unusual pro- gram of technical papers, symposia, lectures and addresses, interspersed with luncheons, dinners, excursions and worthwhile entertainment for the four days has been arranged. The curtain rises on Monday morning and the first act is by the entire company-registration. Then the meeting hits its stride, for there are ten technical sessions on Monday, and the range of subjects includes most of the Institute membership. The Committee on Coal and Coal Products, which is about to become the Coal Division, presents a symposium of a dozen or more papers on Coal Classification, concluding its afternoon session with several papers on general subjects. At its luncheon between sessions, C. E. Bockus, president of the National Coal Association, will be the honored guest. Papers of theoretical character will be discussed at the morning session of the Committee on Geophysical Prospecting; at its afternoon session there will be presented summaries of results obtained at various properties by methods described at previous meetings of this group and permanently recorded in "Geophysical Prospecting," published by the Institute early in 1929. Members of the Petroleum Division should not overlook the paper by Theodor Zuschlag, on this Committee's program. It is entitled, "Oil Structure Mapping by the Sundberg Method." Members of the Iron and Steel and Institute of Metals divisions will find it profitable to attend the session on Engineering Education on Monday afternoon. E. A. Holbrook has arranged a program of ten-minute talks on Metallurgical Education which are designed to get down to "brass tacks." and the practical man may, in discussion, contribute as well as learn. At 5 p. m. Thomas T. Read will lecture+ at Columbia University, on "Recent Progress in Economics of the Mineral Industries."

Jan 1, 1930

By C. C. Furnas, T. L. Joseph

It is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investiga-tion1,2 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper. Importance of Gas-solid Contact One of the authors has pointed out in a previous report? that the operation of the blast-furnace process is entirely dependent on contact between the gas stream and the solid particles in the stock. The gas stream carries the necessary heat as well as the carbon monoxide molecules that do the work of rednction. In the parts of the furnace in which there is little or no contact between the gas stream and the solids there can be little work of reduction. Obviously, the part of the apparatus that is not doing the work for which it is intended is inefficient; the ideal condition is one in which all portions of the stock column are

Jan 1, 1929

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942