Search Documents

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

The Molycorp operation at Mountain Pass, California, is unique in that it is the only place in the world where bastnasite is mined. The orebody is a metamorphic carbonatite; the mineral of importance is bastnasite, a fluocarbonate containing principally cerium, lanthanum, neodymium, and praseodymium, with small amounts of samarium, gadolinium, and europium. In addition, appreciable quantities of barite, calcite, and strontianite are present. Molycorp had mined and processed the bastnasite ore since the early 1950s at a rate of about 100 tpd by a unique hot flotation process in a plant originally used for cyanidation of gold ore. The concentrate was primarily used in high quality glass polishing, lighter flints, ceramics, and in specialty steel making. Then in the early 1960s, Molycorp and the Colorado School of Mines Research Foundation developed a solvent extraction process to recover europium from the bulk rare earth concentrates. In 1965 a new SX plant was constructed to produce this material for use as a red phosphor in color television tubes. Because of the demand for this material, a new 500 tpd concentrator was designed and constructed in 9 ½ months. Then, because of a sharply increased demand for europium, the plant was expanded to 1200 tpd only four months after completion of the original construction. The crushing section of the new plant was designed similarly to those portable units used in road construction and arrived on the site in ten major pieces. Foundations were concrete piers; and after their completion, the entire crushing plant composed of primary and secondary crushers, conveyors, and a screen was erected in fourteen days by a crew of ten men assisted by a mobile crane. Pit-run ore is loaded into 35-ton trucks by a 7 yd (5.4 cu m) loader, trans- ported to .the crushing plant, and dumped into the 65 -ton concrete pocket. A 42 in. by 20 ft (1.07 m by 6. 1 m) apron feeder feeds ore to the 30 in. by 42 in. (760 rnrn by 1070 mm) single toggle jaw crusher. Crushed ore is trans- ferred by a scissors conveyor to a 5 ft by 14 ft (1.52 m by 4. 27 m) double- deck screen which produces a final ¾ in. (19 rnrn) product with the oversize being treated in a 4 ¼ ft (1. 3 m) standard cone crusher. Cone crusher product is returned to the first scissors conveyor to join the primary crusher product. Dust collection is by a wet scrubber, and an operator's control room is located to overlook the primary. The entire crushing is in the open, and a 30-ton mobile crane is used for maintenance. Molycorp’s two-stage crushing plant is an excellent example of functional design for a small mining and milling operation.

Jan 1, 1978

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

During the past 60 or 90 days, the metropolitan newspapers have published much concerning unemployment throughout the nation and the efforts of the Army and various other bureaus for finding work for the returning soldiers. The United States Employment Service has 2000 bureaus throughout the country, which Nathan A. Smyth, Assistant Federal Director, states have placed more than 2,400,000 persons in employment. The Engineering Societies Employment Bureau, which, since December, 1918, has been endeavoring to put all returning engineers in touch with employers who need efficient men, has produced results that are very gratifying to the Secretaries of the four Founder Societies under whose direct management the Bureau operates. During this period, 1615 men have registered at the Bureau's office in the Engineering Societies Building; not all of these, however, are unemployed. Many are ex-army and navy men, who in passing through New York on their way home, look over the field in the hope of making a change for their own benefit before returning to their former positions. During this period, 427 positions vacant have been filed, 2300 of which positions have been filled from the men registered. The letters mailed by this Bureau amount to about 1000 a month and the number of personal calls at the office, 1600. The lowest number of positions filled has been in mining, but the lowest number of registrations is also from mining men. While in February idleness throughout the nation was increasing at the rate of 35,000 a week, under date of Mar. 7, Arthur Woods, a special assistant to Secretary of War Baker, states that there is a material improvement in the unemployment situation and that the problem is no longer a serious one. It is recognized that' the improvement wrought in each individual by his military training and experience has so increased his value that it is 'not only unfair, to ask these men to accept their old jobs at the old wages, but it is probably very unlikely that they will be willing to do so. This plain statement of improvement may not carry conviction to everyone but a concrete example will show its validity. Take the example of a young man under 21, bright and intelligent, with only a high-school education who was employed, before being drafted, on purely manual labor. He shows up well under military training and is made a corporal; he makes good and is appointed a sergeant; and finally becomes top sergeant, which requires him in many ways to handle the entire company of 250 men. The result is; even if he has not been tried by the fire of battle, he comes out of the army with a feeling of self-confidence and capacity that was entirely lacking when he went in and he has had actual experience in handling a larger body of men than the average mine foreman at twice his age, and he has had twice the average amount of detail work to take care of.

Jan 4, 1919

Shovel To further increase the efficiency in the production of their foundry sand, the American Silica Sand Co. has purchased a new and improved shovel that will be used for loading trucks at their Reynolds Pit. The [ ] new shovel will greatly facilitate winter mining operations and make possible larger winter shipments of the company's foundry sand. The Reynolds Pit is one of three sand pits in the Ottawa district owned by American Silica which produce sand that is refined for foundry use. Circle No. 1 Electric Switches The Crane Electric Co. has just announced the production of their R-1000, a new rotating limit switch designed to control the travel of any rotating device requiring interruption or establishment of electrical current after a predetermined number of revolutions. It is useful for machinery, lifts, and other power equipment. The switch is presented in a finished case, 16 gage, reinforced, with walls of sufficient strength to hold the entire mechanism and all the parts in accurate alignment. The worm gear combination has a 60 to 1 ratio, sufficient for most industrial uses. The number of revolutions can still be increased by using various combinations of driving sprockets, either on the shaft of the switch, or on the sprocket of the unit controlled by the switch itself. Circle No. 2

Jan 1, 1952

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a common occurrence in coal mines of the Northern Appalachian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and formation of cutter roof failure. In-mine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dikes registered the greatest amount of roof loading near the intersection of dikes with the rib. Load cells measuring horizontal pressure changes in the roof indicated that the greatest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysis of rock pressure monitoring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectively support the roof in areas of clastic dikes and prevent cutter roof failure. However, these methods were only successful when employed shortly after mining.

Jan 1, 1984

By B. Silliman

THE remarkable outflow of natural gas recently developed in Western Pennsylvania, and along the valley of the Ohio and its tributaries, has called attention to an important series of patents for improvements in glass-fnrnaces and the manufacture of glass, which the brothers Siemens have made since 1872. The basement-patent of this series, is No. 127,806 of the U. S. Patent office, and is of date June 11th, 1872. This has been followed by eleven other patents (including one re-issue), all for improvements in glass-furnaces, or methods of manufacture, of which the latest is of date July 11th, 1882. Nine of these patents were issued in 1880-82. The following is the list of these patents, in order of dates, viz.: 1872. June 11th. No. 127,806 (U. S. office), Improvement in glass-furnaces; 17 sheets drawings, 5 pages text. This is the basement-patent. 1877. April 17th. No. 139,800. Improvement in the manufacture of glass; 3 sheets drawings, 2 pages text. Boats and floating vessels swimming in the liquid glass of the tank-furnace. Re-issued in 1880. q. v. 1880. April 27th. No. 226,931. Furnace for annealing and tem pering glass. " July 13th. No. 220,846. Glass-melting-furnace. " August 3d. No. 230,668. Glass-melting-furnace; 4 sheets drawings, 2 pages text.

Jan 1, 1885

THE distinction btween price reduction as a re-sult of lowering of production cost and price re-duction through unrestricted competition cannot be made too clear, because they are often interwoven in actual experience. Take the whole population of a town whose principal industry is shoe manufacturing as a concrete example. If the manufacturer is able to cut his price per pair in half because he has found out how to make a pair at half the cost, he will com-monly let a number of his men go, because reduction in production cost usually results from substituting cheap mechanical energy for expensive human energy. These people will normally find other employment. The workmen who remain employed usually earn more in dollars than they did before, and in spending it give employment where there was less before. Mining companies that initiate considerable enter-prises in foreign lands where the economic level is low, and where most of the people are busily but in-efficiently engaged in raising enough food to support themselves and their families, often find themselves confronted with an acute labor problem. If any con-siderable number of workers leave the land to work in and about the mines, those left on the land cannot raise enough food to keep them all unless they are taught better methods of agriculture and provided with equipment that will enable them to produce more with less expenditure of effort. Add to this the fact that managers commonly find that the "natives," as our British cousins designate them, usually need more food and a better balanced diet than they have been accustomed to in order to show anything above the lowest order of efficiency in industrial work,. and it is clear that to make a new industry possible in what may be termed an economic province involves increas-ing the productivity, not only of those who are em-ployed in it, but of the whole social group. It has already been pointed out that the employ-ment of large numbers of men in automobile manu-facture is only possible because the others have in-creased their productivity enough to turn out every-thing else that is needed without the help of the auto-mobile workers.

Jan 7, 1928

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick's second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. 'The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick's second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank' have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank's suggestions to diffusion in alloys has been discussed by Wagner.' Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

By Henry Hanson

A STUDY of the ore to be treated should be the first step in deciding on a machine for crushing or grinding. Coarse crushing is practically confined to the jaw and the gyratory crushers, the large-size jaw type being often employed in large installations as a primary crusher, followed by the gyratory type for secondary reduction. In small plants where mine-run ore is reduced in a single step, either of these machines will do the work. In intermediate and fine grinding, various machines are used. The relative merit of the different types will be governed in no small measure by the size of the installation, the character of the ore to be reduced and the final product desired for subsequent treatment. It should be possible, nevertheless, with the data available, if properly classified, to arrive at an approximation of the relative efficiency of these intermediate and fine grinders. It should be possible, also, to determine the economic grinding range of the different machines. With this in mind, it will be the object of this article to indicate, in rough outline, how the data available may be classified, rather than to attempt to discuss any particular practice and compare the results with other practices. Conclusions or generalizations can not be drawn without an exhaustive classification of data; in fact, many vital points will have to be determined by additional experiments which can be carried on most advantageously in the laboratory. The expense en-tailed in such experiments would be worth while if the data obtained should lead to definite conclusions that would aid in standardizing and simplifying grinding practice.

Jan 2, 1923

By George D. Dub

INTRODUCTION OWENS LAKE is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.2H20) and borax, (Na2B407.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. CLOSED BASINS Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I Chloride type; largely sodium chloride (NaCI) and of oceanic type, such as Great Salt Lake. Related is the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. 2. Sulphate type; largely sodium sulphate (Na2S04) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate-chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate-Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1947

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956