Search Documents

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or. other persons.) Position for a single man experienced in cyanide mill construction and operation at a small mine in Nicaragua. Salary $150 per month and expenses. No.. 39. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, desires position in ore dressing, either experimental or operating. Has had practical experience in flotation and other special methods. No. 228. Member, technical. graduate, 10 years' experience in Belgian coal mines, five years' experience in American coal mines in connection with reorganization of companies and opening of new coal fields. Aged 37. Speaks Spanish. No. 229

Jan 7, 1915

By C. A. Lemke

THE ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from ;the company's mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent. of the total ore. These three minerals vary considerably' in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver h Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment.

Jan 9, 1925

By L. C. Armstrong

Twice in the past two years and in two widely separated localities—ane near Williamsville, Mo., and the other in the Allard Lake district of Quebec— the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately inter-grown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely. It should be pointed out that the lack of time and funds made it impossible for the writer, or other persons interested in correlating the details of bit histories with the kinds of rocks drilled, to be present during the performance of the contracts. However, the records kept in the normal course of drilling are deemed complete enough to be reportworthy. This information is presented here together with the findings made in studies of the rocks involved, with the thought that it may attract the comments of others who may have encountered similar refractory drilling conditions. A pooling of knowledge on the problem would be of material aid in devising more efficient cutting tools and procedures for penetrating this kind of rock. Drilling Blastholes in the Williamsville Granite Due to the unsatisfactory perform- ance of pneumatic percussion drills in boring blastholes on a construction contract near Williamsville, Mo., tests were made with a diamond drill. The poor progress achieved and the excessive loss of diamonds, however, soon led to the abandonment of these trials. The diamonds, in all of the bits tried, lost their cutting edges and acquired a polish after being in service for distances ranging from a few inches to a few feet. Coring bits containing surface-set, whole-stone bortz in a tungsten powder matrix were employed. The cost assignable to bortz wear averaged $7.17 per foot. This item of expense is several times the amount normally expended in diamond drilling in firm, unfractured, granitic rocks. Diamond-impregnated, tungsten carbide bits also were used without success. The diamond wear was at the rate of $0.98 per foot, but the diamond chips became too polished for further duty in less than a foot of drilling. The Williamsville granite is pink and medium-grained. In the hand specimen, it has a fresh, sound appearance; it is seemingly composed almost entirely of interlocking grains of feldspar and quartz and has no discernible features suggesting a greater durability than is usually found in rocks with this composition and texture. Microscopic examination, however, reveals a predominance of feldspar grains with more or less regularly distributed and sharply angular masses of quartz (see Fig 1). The pattern assumed by the two minerals in this mode of occurrence is referred to as a "graphic intergrowth," as it bears some resemblance to the cuneiform characters of ancient Persian writing. The other principal constituents are quartz-free feldspars (microcline and orthoclase) and quartz. All of these constituents are in nearly equidimensional grains, ranging up to about 3 mm in length. There are also

Jan 1, 1950

By R. J. S. Brown, B. W. Ganison

A new logging method has been developed, based on measurement of the nuclear magnetism of formation fluids. The nuclear magnetism log (NML) is the only log that responds solely to formation fluids. It operates equally well in both oil-base and water-base muds and in empty holes, and can be used in all kinds of formations except strongly magnetic ones. Two separate NML measurements can be made, one of which provides a continuous formation fluid curve. This fluid curve is called the free fluid log (FFL) and is believed to indicate a minimum effective porosity in most formations. The FFL not only delineates fluid-containing zones, but provides an excellent correlation curve that can be obtained under conditions where conventional correlation logs are ineffective. Preliminary tests indicate that the second kind of NML measurement may help distinguish oil and water zones and provide information concerning permeability and wettability. (The FFL itself appears to provide some information on permeability.) The second kind of NML measurement requires stopping the logging tool for a short time opposite a zone of interest and taking more extensive NML data that can be displayed as nuclear magnetic relaxation curves. In some instances, oil and water saturations for the region immediately adjacent to the borehole can be read from these relaxation curves. INTRODUCTION In 1946, Bloch, Hansen and Packard and Purcell, Torrey and Pound3 independently announced the successful demonstration of the phenomenon of nuclear magnetic resonance. During the past 13 years, there have been many applications of nuclear magnetic resonance, including applications to the study of chemical structure and to the measurement of magnetic field strengths. Preliminary experiments on the feasibility of using nuclear magnetism measurements in well logging were made independently by California Research Corp. and Varian Assoc., the Varian work being sponsored by the Byron Jackson Tools, Inc. Since then a cooperative research program on nuclear magnetism logging has been carried out by the Byron Jackson Div. and Research Center of Borg-Warner Corp., and California Research Corp., subsidiary of Standard Oil Co. of California. The use of nuclear magnetism in well logging is of special interest because it offers a way of making direct measurements on the hydrogen in the formation fluids and not on the rock matrix. Within the past 1 1/2 years, successful measurements have been made with a research model logging tool in wells in California, Tex as, Utah, Louisiana and Wyoming. NUCLEAR MAGNETISM SIGNALS Polarization, Relaxation and Precession Many atomic nuclei possess magnetic moments and spins; that is, they are similar in some respects to bar-magnet and gyroscope combinations. Molecules and their nuclei are subject to thermal motion, which has a scrambling effect, tending to leave as many nuclear spins oriented in any one direction as in any other. However, if a magnetic field is applied, the magnetic nuclei tend to align in the direction of the field. The scrambling and aligning forces compete with each other, with the result that a few more spins are oriented parallel to the field than in other directions. This gives a net magnetization, or polarization, which is directly proportional to the strength of the applied magnetic field (aligning influence) and inversely proportional to the absolute temperature (scrambling influence). When the magnetic field in, or temperature of, a liquid sample containing protons is changed, the new equilibrium value of proton polarization is not established immediately but requires an amount of time which depends on the nature of the hydrogen-containing materials. The process of approaching the equilibrium value of polarization is called relaxation.'.' Polarization is a vector quantity, and the components parallel to and perpendicular to the magnetic field must be considered separately. Relaxation of the component parallel to the field is called "thermal relaxation", or "longitudinal relaxation", and the corresponding time for this component of non-equilibrium polarization to decay by a factor of e (natural log base) is denoted T. The relaxation of the perpendicular component is called "transverse relaxation", and the corresponding relaxation time is denoted T,. The potential energy of a magnet in a uniform field depends on the angle the magnet makes with the field; therefore, a change of the component of net polarization parallel to the magnetic field involves an exchange of energy between the spin system and the thermal motion of the molecules, leading to the term thermal relaxation for the relaxation of this component. Suppose we subject a sample to a strong magnetic field at right angles to the earth's field for a time greater than TI. A polarization, thus, is established at right an-

By Keith G. Kirk, Lawrence E. Welborn, Patrick A. Ley

Over the past two years the Office of Surface Mining in conjunction with Energy & Minerals Technology Assessment, ENCORE Systems Inc., and Boeing Computer Services has developed the Economic Coal and Ore Reserve Estimation (ENCORE) Coal Seam Modeling System. This system is being used by OSM, certain states, and industry for mine planning and mine plan permit review. The ENCORE system enables the mining engineer to start at the reserve estimation stage of surface mine planning and continue through the entire mine planning process and into the permit preparation process. The ENCORE system enables the state and federal regulatory authorities to assess a given mining and reclamation plan permit application in a rapid and efficient manner and greatly speeds up the mine plan review and permitting process. The ENCORE system is user friendly and menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Data are input both through digitized map files and bore hole information files and stored in a data base that is an integral part of the ENCORE system. The system performs reserve estimation through standard polygon methods, least square methods, and geostatistical (kriging) techniques. Geostatistical routines permit rapid evaluation of coal and overburden quality and quantity. System outputs include drill hole sumnary and resource summary reports, cross sections, isopach maps, structure contour maps, premining topography maps, postmining topography maps, and three-dimensional perspective views. The maps can be displayed on a high-resolution, color graphics terminal or generated by a high quality plotter and are suitable for direct inclusion in the mining and reclamation pl an permit application. This paper gives detailed examples of ENCORE'S use together with example outputs.

Jan 1, 1983

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

By Carl E. Swartz

The Joint Session on Continuous Casting, of the Institute of Metals Division and the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers, convened in the Jade Room of the Hotel Waldorf-Astoria, New York City, on Feb. 23, 1944, at 9:15 o'clock, Carl E. Swartz presiding. C. E. SWartz.—It is gratifying to see so many out at what may seem an early hour for the beginning of A.I.M.E. sessions, but I think this number-—some fifty or sixty of you —is an adequate expression of the interest in these processes all over the United States, and possibly in foreign countries. I would like to ask those who feel that this type of program is of value to you to write or speak to some one of the Institute of Metals Division officers and suggest other topics for symposiums. We have a feeling that some of these current practices are of interest and we believe that under proper sponsorship many of the companies mill be willing to give publicity to processes such as those that will be discussed today. Also, we would like suggestions and criticisms, so that the next ones can be better. The subject of continuous casting is not new, of course. The two papers on the program this morning will adequately cover the history and some of the earlier processes, some of the theory and some of the practice, some of the reasons why these various methods did not work. I was rather interested in discovering, when thumbing through one of the A.I.M.E. publications tile other night, an article on continuous casting. I was not aware that the A.I.M.E. had published any papers on continuous casting, but there may be a number. The one that I happened to find was published in the 1915 volume, on the Mellen rod-casting process, and so we might say this is not the first session in which these subjects have been under discussion. However, there have been many improvements since then in all fields of metallurgical and mechanical engineering; consequently, I think that the papers today will be a little more involved and a little more complete in their technique. The first paper today will be given by one of our gentlemen of the press, who has done one of the outstanding jobs in this country in calling to our attention some of the newer processes that are being considered and being used in the metallurgical indus-

Jan 1, 1945

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

Butte Meeting. It is expected that the technical program of the Butte meeting will be a sufficient attraction to draw to that point every member who can possibly get away long enough to attend. Attention is particularly called to the papers already sent in by the Committee on Precious and Base Metals, and the papers which they are undertaking to secure for the meeting, as published on pp. ix and x. In addition to these papers, and in addition to those published in this Bulletin, the office of the Institute already has in hand several papers, which will be published at an early date, and presented in abstract and discussed at the meeting. Of the discussion of these papers a special feature is being made. Therefore, let every member come to Butte who can do so. A meeting of the Board of Directors of the Institute will also be held at Butte. In the May Bulletin, we stated for the information of members the railway excursion rates for two suggested tours in connection with the meeting, which included Glacier Park before the meeting and Yellowstone after it. The itineraries there given and rates quoted were planned and offered by the railway agent bureaus in New York. Circulars have been sent to the members of the Institute by A. E. Vaughan & Co., a tourist trip agency of New York City, containing details of tours nearly identical with those outlined in the Bulletin, and quoting rates covering, the expenses of the whole trip. Members can easily compare these rates with the rates offered by the railroads, and published in the last Bulletin. In order that no misapprehension may exist, the statement is here made that the Institute and its officers have no connection whatever with Vaughan & Co.'s proposals and that any such tours will be strictly personal matters between said company and the members of the Institute who take them. Nevertheless, the Board of Directors calls to the attention of members the circumstance that tours such as these will afford an opportunity for members to travel together to the meeting.

Jan 6, 1913

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgments are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate, and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources. Basic Reasons to Establish a Limestone Quarry Profit Motive: Certainly the dominant and overriding motive must be that of attaining a reasonable profit. In certain situations a quarry firm may acquire land, necessary rezoning (if required), and satisfy all of the other prerequisites preparatory to beginning operations but delaying the actual development.

Jan 1, 1980

INTRODUCTION This chapter summarizes porphyry copper deposits within the State of Alaska. Prospecting for porphyry copper-type deposits in Alaska germinated during the 1940's, grew slowly during the '50's, boomed during the '60's, and matured in the '70's. Although large expenditures have been made in the search for porphyry-type deposits, most accrued data lies dormant in company files. However, an adequate base exists in the literature for a general synthesis of areas that contain porphyry prospects. To simplify the summary, porphyry molybdenum deposits as defined by Clark (1972) are omitted. Description of deposits in their geologic setting permits some correlations between deposit characteristics and crustal environment. These correlations allow speculation about the genesis of the deposits. The summary also attempts to group deposits on the basis of general mineralogic characteristics because diorite model deposits are separated from quartz phenocryst-bearing hosts. Data presented in this chapter summarize observations by the author, published descriptions of specific areas and deposits as noted in the bibliography, and comments by various government geologists. E. M. MacKevett, Jr., D. H. Richter, and H. C. Berg of the US Geological Survey have been particularly helpful. Because few comprehensive descriptions of individual porphyry copper deposits exist for this area, much of the data presented is new to the literature. Details of structure, isotopic geochemistry, and petro- genesis for individual deposits are largely lacking and even the general geology of some belts is not well understood. Details on petrography of Alaskan porphyry copper occurrences are inadequate for construction of ternary diagrams (e.g., Figs. 36a, b, pp. 103, 104, for the northern Cordilleran orogen). Petrographic descriptions summarized in the text are largely from published descriptions whose sources are cited. Porphyry copper-type deposits in Alaska include deposits with pervasive pyrite that contain disseminated copper (but not necessarily coproduct molybdenum). Available data preclude differentiating the deposits by size. No Alaskan porphyry copper deposit is now in production but this is believed to be, in part, a function of economics. In some cases available geologic information is in- adequate for classifying deposits. Some de- posits included with porphyry copper may, with further exploration, be demonstrated to be some other genetic type. Alaska has three distinct porphyry copper provinces: the Hogatza plutonic belt, the Continental Margin belt, and the Interior belt. Each belt contains deposits with characteristic geologic features distinct from those of other belts. Fig. 24 shows the continental margin belt to extend inland from

Jan 1, 1978

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By A. L. Holley

The first session was held in the rooms of the American Philosophical Society, on Tuesday evening, February 26th. The President, Dr. T. Sterry Hunt, called the meeting to order, and after a few introductory remarks concerning the importance of theoretical and speculative science, which often involves principles of the highest economic value, and, more than all that, serves to enlarge our conceptions of the universe, and ennoble us, by the cultivation which it affords to our most exalted faculties, proceeded to discuss some points in the chemistry of the atmosphere. It is known that there is in the crust of the earth a great amount of oxidized carbon, not only in the shape of coal, but also in the graphite or plunlbago of the crystalline rocks, in the various bituminous shales or pyroschists, which are found in all succeeding rock-formations, and also in the forms of bitumen and petroleum. All the analogies of nature lead us to conclude that these various carbonaceous substances have had an organic origin, and have been generated by the deoxidation of carbonic acid, a process effected by the growing plant, and attended with the liberation of oxygen. He showed that the carbon of a layer of coal covering the whole earth's surface to the thickness of one meter, would, in its production from carbonic dioxide, liberate an amount of oxygen equal to that now present in our atmosphere. But bituminous coal contains also a large amount of hydrogen, derived from the deoxidation of water, which implies the liberation of a farther portion of oxygen. The amount from this latter source would equal, for the various coals and asphalts, from one-eighth to one-fourth, and, for the petroleums, onehalf of that set free in the deoxidation of the carbon which these hydrocarbonaceous bodies contain. From what we know of the composition of the stratified rocks, it is probable that they include an amount of deoxidized carbon and hydrogen many times greater than that contained in a layer of coal one meter in thickness, and, consequently, that the disengaged oxygen in past ages must have far exceeded that now present in our atmosphere. To this must be added

Jan 1, 1879

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By W. S. Ayres

THE boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqua, Lehigh Valley Railroad, built at the company&apos;s shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist&apos;s hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seen to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally ; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

Jan 1, 1874

By W. S. Ayres

The boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqtia, Lehigh Valley Railroad, built at the company&apos;s shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist&apos;s hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seem to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two