Search Documents

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By C. L. Berrien

Many fires have occurred in the mines of Butte in recent years, and while all have been of a serious nature, simply because they were mine fires, six of them have been especially dangerous in respect to loss of life and property, and the expense of extinguishing or controlling them. It is not my intention to discuss the relative merits of methods used in fighting these different fires because the conditions under which they occurred varied in each case, and it was not always advisable to expend the large sum of money necessary to actually extinguish them if they could be bulk-headed off from the rest of the mine. It is needless to say that everything possible has been done to check all fires at the beginning, but without success in some cases; and it has then become necessary to bulkhead all connections to them, in which state several now exist. The mine fires of Butte, or fires in any mine, may be divided into two classes, namely: Those occurring in accessible workings, and those occurring in inaccessible workings; because these two conditions govern to the greatest extent the methods of fighting fires. Accessibility and inaccessibility in the case of mine fires concern not only new open workings and old closed workings, respectively, but also the condition of the ventilation in and about those places. When a fire is accessible at the start it should not be difficult to confine it to a small area and extinguish it in a relatively short time, but when it is impossible to actually reach a fire in old filled, abandoned workings, or there is no opening by which the gases may be conducted away from the fire zone, then the time consumed in changing those conditions permits the fire to increase to such an extent that it is a long, hard fight to overcome it. These different conditions have been met in Butte, and of the six fires of serious proportions the Steward mine fire and the High Ore-Modoc mine fire were in new accessible workings and were extinguished in a month or so. The Anaconda mine fire, the Leonard-Minnie Healy mine fire, the West Colusa mine fire, and the Mountain View mine fire, were all inaccessible. The Anaconda mine fie started about 25 years ago and though safely bulkheaded is still active. The Leonard-Minnie Healy

Jan 1, 1916

By D. W. Fuerstenau, G. D. Gumtz

Use of the discretized batch-grinding model for the simulation of locked-cycle grinding tests from batch-grinding data is illustrated. The simulated results were compared with actual locked-cycle experimental data for the dry grinding of dolomite. To illustrate the utility of this simulation method, a number of relationships between operating and performance parameters were generated, including relations between batch grinding and the Bond test, the production rate and the circulating load, and the production rate and the product size. A large amount of testing is done each year in the mineral industry for use with grinding unit cperations, and much of the experimental test data is obtained by the tedious locked-cycle testing procedure. In addition to being experimentally complex and requiring large amounts of sample, the very nature of the locked-cycle experiment yields results that cannot readily be interpreted. The attempts that have been made to model comminution systems during the last few years may provide a better and simpler way to obtain and analyze grinding test data; these models involve elements of both fitting to "model equations" and deterministic representations.1-1 The traditional engineering design techniques for comminution systems have relied mainly upon large amounts of industrial operating data that have been correlated with locked-cycle grinding data.',' Bond's empirical mill-design procedure involving locked cycle testing remains the most generally available method to this day. The purpose of the present paper is to show how much more useful data can be obtained from a simple batch-grinding experiment that provides information which subsequently can be utilized with population balance models of the grinding process to simulate locked-cycle behavior. These simulation results can, of course, be used in Bond's general design scheme. However, the combination of batch-grinding tests and the population balance model allows many more conditions to be considered than do single laboratory tests under specific locked-cycle conditions. The use of these simulation techniques for prediction of locked-cycle behavior represents one of the first practical applications for the simulation method in comminution.

Jan 1, 1971

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916

By Sherwin F. Kelly

THE present lull in engineering activities presents an advantageous moment for inquiring into the position now occupied by geophysics in its various fields of application. The recent over-expansion in all lines of work resulted in an uncritical employment of these methods of exploration which was bound to have its harmful reaction. The pendulum has now swung back, producing a decidedly hypercritical attitude toward the new science that had been recently welcomed so joyfully as the panacea for prospecting troubles. The severe retrenchment in exploration has forced upon us a period of waiting and, it is to be hoped, of profitable contemplation. This can well be employed in trying to pass a reasoned judgment on what position geophysics should occupy in the new geological exploration programs that will inevitably ac- company the looked-for industrial recovery.

Jan 1, 1931

By J. J. Fritts, J. L. Patrick, T. L. Wright, C. O. Ensign, W. S. White, J. W. Trammell, J. C. Wright, D. J. Hathaway, R. J. Leone

The copper deposit at White Pine, Michigan, from which a little more than 5 per cent of United States primary copper currently is produced, is a large stratiform orebody, 4 to 25 feet thick and several miles across. The present ore column, containing about 1.2 per cent copper as chalcocite and native copper, is confined to the basal beds of the Nonesuch Shale. This upper Keweenawan (Upper Precambrian) formation is a distinctive gray siltstone unit, about 600 feet thick, overlying and overlain by thick red-bed sequences. All these rocks contain abundant volcanic debris, but the latest known igneous activity within 50 miles antedated the Nonesuch Shale. The rocks are unmetamorphosed and only moderately deformed, mainly by tilting and faults. Pyrite, presumably syngenetic, is the only prominent sulfide throughout most of the Nonesuch Shale. The basal beds of the formation, however, contain disseminated copper minerals instead of pyrite and constitute the cupriferous zone. On a regional scale, the top of the cupriferous zone cuts across bedding, and ranges from an inch or so above the base of the formation in some areas to more than 50 feet in others. However, within the cupriferous zone the distribution of copper shows remarkable stratigraphic control. Certain beds are copper-rich compared to the beds that lie between them and the differences persist throughout the White Pine region. Several darkgray thinly laminated beds in the lower 10 to 25 feet of the Nonesuch Shale are rich enough and sufficiently close enough together to constitute a mineable thickness where they lie within the cupriferous zone. Pyrite is the characteristic sulfide of the Nonesuch Shale as a whole. The principal sulfide mineral of the cupriferous zone at the base of the formation is chalcocite. The succession of minerals outward and upward from the center of the cupriferous zone is native copper-chalcocite-bornite-chalcopyrite- pyrite. The bornite and chalcopyrite are confined to a narrow fringe at the margin of the cupriferous zone. This pattern of mineral zones is believed to represent reaction between syngenetic pyrite and introduced copper. The main copper mineralization is independent of structure and apparently antedates deformation. Details of the geometry of the cupriferous zone indicate the possibility that copper was introduced from the underlying sandstone prior to lithification. The source of the mineralizing solutions and their copper is not known.

Jan 1, 1968

By F. L. Bosqui

The history of the development of gold metallurgy in South Africa is divisible into two periods: That preceding the introduction of the cyanide process on a commercial scale in 1890; and the 24 years intervening between that important event and the present time. The period between the discovery of the banket reefs of the Witwaters-rand and the year 1890 was one of phenomenally rapid progress in mining development, but of no special interest to the metallurgist, There were no strikingly original or distinctly local advances in the treatment of gold ores. Californian practice in stamp milling and amalgamation prevailed, in mills ranging in equipment between 5 and 50 stamps, operating within a wide range of efficiency, and under the trying conditions usually encountered in a new and isolated field. The somewhat incomplete records of gold output of that period show that in December, 1887, there were 20 producing companies in the Witwatersrand district, of which 10 had mills, the largest being of 20 stamps. The only official record of returns for May, 1887, was that of the Wemmer mine, whose modest achievement with a 5-stamp mill was 100 tons crushed, producing 887 oz. 3 dwt. of gold. This is interesting in view of the present-day output of this field, which in 1913 reached 8,430,998 oz. The rapid increase of production during this first period (May, 1887, to January 1891) is shown by the following summary for the year 1890:1 Total tone crushed.................................. 702,828 Number of stamps in operation....................... 1,046 Average number of tons crushed per stamp per day..... 2.36 Yield of gold, ounces................................ 494,817 Yield per ton, pennyweights.......................... 13.36 The stamp duty ranged between 11/2 and 4 tons per day, according to weight of stamp, fineness of screen, and operating skill available. The prevailing weight of stamp was about 900 lb., and the screen, 900 meshes to the square inch.

Jan 1, 1916

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,' and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers' Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By AIME AIME

AT bottom of this page is a photograph recently taken by a student-John E. Stewart-of the most northerly situated college in the world, the Alaska Agricultural College and School of Mines. It is situated at College, near Fairbanks, Alaska, approximately on the 65th parallel of latitude, and therefore just south of the Arctic Circle. It is farther north than Hudson Bay, and in about the same latitude as southern Greenland.

Jan 1, 1932

By Lester A. Blackner

The Ray Consolidated Copper Co.'s mining property is located on Mineral Creek, 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig. 1). The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. General Characteristics of the Orebody The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers 205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly from both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography. The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations. The bulk of the ore is chalcocite disseminated in schist. In places cupriferous pyrite is closely associated with the chalcocite. The mineralized gr'anite-porphyry forhations are contiguous to the ore-bearing schist. • Overlying the orebody is an oxidized zone of leached iron-stained schist, averaging 252 ft. in thickness, termed "capping." The Line of

Jan 1, 1916

By Gordon B. Brox, Joseph F. Mcaleer, Charles C. Goddard, Edward P. Shea, Robert G. Ingersoll, Lester G. Zeihen, George J. Burns, John M. Guilbert, Richard N. Miller, Charles Meyer

The Boulder batholith is a composite intrusive in which the Butte quartz monzonite is the dominant rock type. Quartz porphyry dikes intruded the quartz monzonite in directions which were subsequently followed by the eastwest- striking Anaconda system of veins, the earliest major veins in the district. Anaconda veins are faulted by northwest-striking veins of the Blue system, which are most prominent in the central third of the district. Anaconda veins are the major producers in the western third of the district and also in the eastern third, where the "horsetail" zones break off from them. Individual oreshoots are thousands of feet long as well as deep on both systems of veins, but they are generally more persistent and thicker on the Anaconda veins. Viewed broadly, the mineralization in the big veins is arranged in crudely concentric zones of zinc and manganese around a central zone of copper. Only slightly offset from these zones, but earlier structurally, is a zone in which quartz-molybdenite veinlets are prominent. This zone tops at about the 2800 level and widens downward. The pattern of distribution of Cu-Fe-S series minerals in the large veins of the copper zone is not symmetrical with respect to the metal zones. There is a fringe of chalcopyrite-bornite all around the copper front. However, within the copper zone, pyrite-chalcocite-enargitecovellite- digenite assemblages are prevalent near its eastern edge from the 3800 level to the surface, whereas deep on the large Anaconda veins in the western part of the copper zone, chalcopyrite is dominant. Here the chalcopyrite grades upward into bornite-chalcocite ores and eastward into the high-sulfur assemblages of the Leonard mine. Sericite-biotite-K-feldspar alteration envelopes, containing up to about 2 per cent copper as chalcopyrite, are present on some of the quartz-molybdenite veinlets at deep mine levels in the molybdenite zone. These envelopes contrast sharply mineralogically and chemically with the later sericitic and argillic alteration envelopes around Main Stage veins. K'0-Ar'0 ratios indicate that they may be older by about 4 m.y. Secondarily enriched copper ores are mined in the Berkeley pit in the southeastern part of the district. At the present time they account for about half of Butte's production of copper.

Jan 1, 1968

By Harold Price

PRIOR to Sept. 1, 1928, there had never been constructed what might be termed a long pipe line with electric-welded field joints. Nevertheless, by Sept. 1, 1929, within the period of a year, more than 2500 miles of electric-welded lines have been completed. These lines vary in diameter from 6 to 20 in., and in length from 50 to 700 miles. Before Sept. 1, 1928, no such line had been constructed .longer than 50 miles, and only one of nearly that length, a 40-mile 7-in. gas line in Louisiana. This was in reality the first pipe line to use electric-welded field joints. During the past year the following lines have been electric-welded by the Welding Engineering Co. alone: Texas Pipe Line Co.-157 miles of 8-in. line from Corsicana, Texas, to San Augustine, Texas. (This was the first electric-welded oil line.) Texas Pipe Line Co.-80 miles of 8-in. from Lafors, Texas, to Childress, Texas. Texas Pipe Line Co.-39 miles of 10-in. from Monahans, Texas, to Jal, New Mexico. Texas Pipe Line Co.-50 miles of 6-in, from San Antonio, Texas, to San Marcus, Texas. Texas-Empire Pipe Line Co.-424 miles of 12-in. from Cushing, Okla. to Chicago, Illinois. In addition to the field welding mentioned above,1 250 miles of 12-in. line was electric-welded into double joints at the pipe mill at Indiana Harbor, Ind.

Jan 1, 1929

Edward Eeller, Baltimore, Md. (communication to the Secretary): Mr. Miller's improved method of the cyanide-assay for copper will, without doubt, be much appreciated by assayers and chemists who are engaged at copper mines and works. The writer, as one who, at one time, had much work of that kind to do, entertains no doubt of its practical value. In enumerating the factors which affect the accuracy of cyanide-titration, Mr. Miller omits to mention time. This I have always considered an essential one; i.e., in order to secure accuracy, I have believed it to be necessary to run the cyanidesolution at the same rate of speed in standardizing as in the titration of the samples. I have accomplished this, without the use of a time-keeper and without noticing the volume of the solution, in the following simple manner: In running the cyanide-solution from the burette, the stream was so regulated, by manipulation of the cock, that it retained its continuity for a distance of about one inch below the orifice, and, below that, broke into individual drops. This means that a constant pressure is maintained at the orifice of the burette, so that, during equal intervals of time, equal volumes of the solution pass through. The stream of cyanide-solution was left to flow in the manner indicated until the blue ammoniacal copper-solution began to show a distinct change in color, after which the cyanide was added by drops at regular intervals until the desired end-reaction. When several burettes are used they should have orifices of equal diameter; otherwise, the timefactor must be considered separately for each. In accordance with Mr. Miller's views, I have always considered the cyanide-method as of very satisfactory accuracy for all copper-assaying in which I did not employ the electrolytic method. It may interest some of my colleagues to know the modified method which I employed some fifteen years ago in making great numbers of copper-estimations on ores and

Jan 1, 1902

By Jennings S. Cox

(Glen Summit Meeting, June, 1911.) THE following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 191.0. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years ; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C. Spencer 1 has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper on The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared.3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit and to call attention to its commercial importance. LOCATION. The Moa district is situated on the north coast of the . Province of Oriente, which is the most easterly province of the island of Cuba. It lies on the northern or seaward slope of 1 Bulletin No. 340, U. S. Geological Survey, pp. 318 to 329 (1908). 2 Trans., xl., 299 to 312 (1910). 3 Iron Age, vol. lxxx., No. 7, pp. 421 to 426 (Aug. 15, 1907), and vol. lxxxi., No. 15, pp. 1149 to 1157 (April 9, 1908).

Mar 1, 1911