Search Documents

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By C. E. LAWAL

WITH the object of adapting high-school vocational courses to the industrial needs of the community, a few high-school officials in West -Virginia working with the School of Mines of the State university decided to try an innovation this year. The purpose of this experiment was to teach coal mining in two high schools situated in mining communities. We thought that if a course in coal mining would be included in the list of optional courses offered in the high school, it might interest some of the boys, and if the course were properly taught it would undoubtedly be of inestimable value to those boys who later decided to take up mining work as their vocation. This coal-mining course was started last September in the Berwind and Gary high schools in West Virginia. The high-school officials in their conferences with' us decided that we should work up the outline of this course and they would assign the science teachers of the schools as instructors, with ,the understanding that we would help 'these instructors with this work. We consented to all this and submitted -an outline to the school officials which they are following this year.

Jan 1, 1929

By WILLIAM E. NEWNAM

THE molding and loading of pig lead has, in the past, been accomplished mainly by the strong arm method and, as the pigs are usually loaded directly into the cars, it has been a hot and laborious task. Of late years it has been difficult to obtain men willing to perform such labor and the need has been felt for loading and molding machinery which would eliminate all manual handling of the hot pigs and which would be sufficiently compact to permit of installation in existing plants with little or no

Jan 1, 1924

By ELIHU THOMSON

IN 1877, Professor Thomson delivered at the Franklin Institute, [Philadelphia, five lectures on electricity. The object of the lectures and the demonstrations, which were numerous and many of them original even to the employment of special apparatus constructed by the lecturer, was to show clearly that electricity, of whatever name, was the same., differing only in tension (as it was termed) and in the current flowing, or quantity (the old term), in steadiness or in wave-like character. In those days, the textbooks divided the subject into statical and dynamic electricity, with sub-divisions such as frictional electricity, voltaic electricity, magneto electricity, electromagnetism, thermo electricity, and animal electricity. The well-known Ruhmkorff coil,' or spark coil as it is now called (as when used for the ignition of automobiles), was employed to step, up a battery current to a high-tension discharge which would charge condensers, such as Leyden jars.

Jan 1, 1921

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By ERIIL SCHROEDTER

THE death, on May 6, 1908, of Dr. Hermann Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony. Hermann Wedding was born March 9, 1834, in Berlin. At the suggestion of Dr. C. J. B. Karsten, the veteran father of Prussian metallurgy and author of the first German text-book of the metallurgy of iron, lie turned his attention, after gradu¬ating from the gymnasium, to mining and metallurgy. In 1853, he began a practical course at the Malapane iron-works, in Upper Silesia. Subsequently, he studied at the Berlin Mining Academy, and received from the University in 1859 the degree of Doctor of Philosophy. A journey which be made to England, somewhat later, led to his undertaking a German translation, with revision and additions, of John Percy's classic treatise on the metallurgy of iron and steel, the publication of which, in successive installments, stretched through many years. In 1863, lie published, as a thesis in connection with his "Assessor's examination," an essay, entitled The Results of the Bessemer Process for the Production of Steel, and Its Prospects for the Rhenish and Westphalian Iron and Steel Industry, which revealed such ability and knowledge as to secure for him a call to the chair of metallurgy in the Berlin Mining Academy.

Jun 1, 1909

By M. A. Scheil

Austenitic stainless alloys are susceptible to stress-corrosion cracking which may occur under certain corrosion environments irrespective of their susceptibility to intergranular corrosion. Test samples are described for investigating stress-corrosion susceptibility of alloys for industrial equipment. A laboratory test using a solution of magnesium chloride boiling at 309 F. was found to produce transgranular cracks in several alloys investigated and in types 347 and 316 stainless steel tubing a residual stress of the order of 10,000 psi. was observed to initiate cracking. The susceptibility to stress-corrosion cracking as judged by the boiling magnesium chloride test indicates that alloys may be selected which will withstand a high stress in service Stressed specimens of stainless alloys included in a corrosion testing program will aid in determining the acceptibility of these fabricated alloys, when stressed, to the service conditions.

Jan 1, 1945

A. O. GATES, Salt Lake City, Utah (communication to the Secretary*).-The writer is delighted by the results shown in Mr. Bell's paper, which prove in an experimental way different from that followed by the writer' that "the work clone in crushing is proportional to the surface exposed by the operation," per Rittinger's Law. Mr. Bell's work was all clone in commercial types of crushing machines, while my work was clone in a testing machine; his work represents fully one hundred times the expenditure and time that my work represented; a great number of tests were made by his organization to determine single points, while I was obliged to depend on the general trend of a curve for results; we agree absolutely that "Kick's law," for which Mr. Stadler was sponsor, does not apply to rock crushing. While my work indicated the reliability of Rittinger's theory, Mr. Bell's work clearly establishes the reliability and makes it Rittinger's law.

Jan 5, 1917

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By George H. Deike

UNDERGRADUATE interest in coal mining engineering has dropped to an alarmingly low level. Most companies having co-operative scholarship programs have been forced to abandon them for the duration.

Jan 1, 1944

By J. A. Retty

HOLLINGER CONSOLIDATED GOLD MINES LTD., through two subsidiary companies, has the exclusive right to prospect in two contiguous areas in central Labrador. This paper presents the results of the mineral exploration that has been conducted in these areas to date. One of the subsidiaries of Hollinger. the Labrador Mining and Exploration Co. Ltd., under an agreement with the Newfoundland Commission of Government, holds an area of approximately 20,000 sq.mi., which comprises the western portion of Newfoundland-Labrador and includes the upper basins of the Hamilton and Naskaupi Rivers. (The main area of the deposits so far discovered may be located on a map at about 67° west longitude and 55° north latitude.) The other subsidiary of Hollinger, Hollinger North Shore Exploration Co. Ltd., has licensed from the Province of Quebec an area of approximately 3900 sq.mi. lying directly north of the Newfoundland-controlled area at the headwaters of the George, Whale, and Swampy Bay Rivers. The M. A. Hanna Co., large iron-ore operators of the Lake Superior region, are participating in the project. With the exception of the years 1940 and 1941, field work has been conducted in the Newfoundland area since 1936, and in the Quebec area since 1939. Hollinger assumed the management in 1942. The field base is at Hollinger Lake, some 300 miles north of the tidewater base at Seven Islands, Quebec, which, in turn, is just west of the mouth of the Moisie River, on the Gulf of St. Lawrence. Air transportation is used exclusively to service the operation.

Jan 1, 1945

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

Jan 1, 1920

By Clyde E. Williams

MORE has been said about the iron and steel situation on the Pacific Coast than has been done .about it; but perhaps as much has been done as conditions have warranted. The production of finished steel in an amount sufficient to take care of the local demand for certain sizes and shapes is an established industry on the .coast. The amount .and the variety of products, so made, changes with the demand or them which is largely dependent upon the growth in population. An increasing demand will not always increase the quantity of steel produced locally because the cost of production may rise so -high as to let in steel from the outside. The reason for this is that all of the steel made in the West comes from steel scrap, the supply of which is .limited. From the standpoint of the metallurgist, it would. be desirable to subititute pig iron for some of ' the steel scrap, but this cannot be done profitably because the pig iron now available is too expensive. In other words, the large future demand for steel and pig iron on the Pacific Coast must be supplied by reduction of ores in the West, unless we are to be content with paying high transportation costs for material produced elsewhere. ."

Jan 1, 1924

By C. A. LINDBERG

Several new methods have been developed on the Iron Range to remove the material adhering to truck bodies in freezing weather. A machine known as a Gradall, incorporating the features of digging both above and below the horizontal, digging angle of blade control, full revolving, travel almost anywhere, and operated by one man, has proven successful in trials at body cleaning. Several of these units are in use with great saving in box-cleaning costs and improvements in efficiency of the truck operation with full capacity boxes. In addition to their winter use, the same machines have been used for ditching and excavating in the summer with great saving. The latest method of combating this freezing problem is to carry the exhaust from the engine through the body, making use of the tremendous heat that is now being wasted. To do this, the present wood sandwich which is used between the bottom of the box and the wear plate is removed and replaced with angles or channels run lengthwise of the box and spaced to permit gases to flow between or through them and also provide a good sup- port for the wear plate. The channels or angles are cut a little short on each end to form a cross passage that permits the gases to flow through the area. In the front end, openings are made in the wear plate and connect to a manifold created by welding a plate across the whole front of the box, spaced from the original end by the original vertical reinforcing angles at that point. The body being described is for a Euclid truck which is the only truck that has been adapted to this body-heating idea to date. At the rear of the truck, the holes from the cross passage are made in the bottom plate of the body and lead into a triangular-shaped body cross member under the scoop end of the truck.

Jan 1, 1949

By Horace V. Winchell

This paper, embodying information acquired by the writer in his work in connection with the Geological Survey of Minnesota, is presented by permission of the State Geologist. Historical.—On November 16, 1890, the workmen of Captain J. A. Nichols, of Duluth, Minn., encountered in a test-pit on the northwest quarter of section 3, township 58, range 18, west of the fourth principal meridian, the body of soft ore now called the Mountain Iron mine. Hard ore, chiefly magnetic, had been known for many years on the Mesabi range, and explorations made by Mr. E. W. Griffin, of Minneapolis, near the falls of Prairie river in T. 56-24 and T. 56-25, and by John Mallmann, at the Mallmann explorations, T. 59-14, had revealed some hard hematite interbedded with quartzite and low-grade soft ore; but this was the first discovery of merchantable hematite on the range. Captain Nichols had been exploring more or less along the range for some two years. To him and to the Merritt brothers, of Duluth and Oneota, who, unshaken in Faith by the discouraging reports of explorers, miners, experts, and geologists, had persevered in the search for ore, great credit is due for the final success, and large rewards have accrued to them already.

Jan 1, 1893

By Julian E. Tobey

A MEMORABLE year has just passed in the field of coal utilization. Because of the war, oil conversions in industrial, commercial, and domestic installations have been made to the equivalent of 20,000,000 tons of coal. The war emergency has resulted in a great shifting of various types of coals to various markets. Huge tonnages of metallurgical-quality coals have been withdrawn from steam and domestic business and sent into the iron and steel industries. Marginal coals have replaced these coals in the steam and domestic field.

Jan 1, 1944

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952