Search Documents

By W. A. Boyer

If the safety factor of a mine hoisting rope is checked for the lowest depth, is the rope then safe for all levels? The answer here is no. A new set of volues is proposed. HOISTS for metal mines are seldom designed for one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper. The safety factor of a hoisting rope as defined by the U. S. Bureau of Mines' is the ratio of the static load to the tensile strength of the rope. It is calculated by dividing the breaking strength of the rope* In Fig. 1 curves A and B are plotted against the vertical suspended distance, which is the abscissa, and the factor of safety, the ordinates. Curve C is a smooth curve drawn through the midpoints of the steps of curve A and would more closely represent the minimum factor of safety for new rope for any particular depth. Curve D is a smooth curve drawn through the midpoints of the steps of Curve B and would more closely represent the minimum factor of safety when ropes should be discarded for any particular depth. If a new rope were applied with a minimum factor of safety, then the vertical distance or ordinate under curve D for any particular depth, divided by the vertical distance or ordinate under curve C, would represent the minimum percent of remaining area intact that could be allowed before the rope would be discarded. Also, that section of the ordinate between curve C and curve D is proportional to the section of the area of the new rope that could be allowed for wear and broken wires. Considering that point at 2500 ft on the chart, the ratio do to co would be the minimum percent of rope area remaining at the point of discard. The ratio of that portion of the ordinate cd to co would represent maximum percent of area of a new rope available for wear and broken wires.

Jan 1, 1955

By D. A. Dukelow, K. Li, G. C. Smith

Decarburization in the Fe-C system by oxygen top blowing has been studied in laboratory -scale experiments. It is shown that equilibrium models fail to explain or predict either the course of refining or endpoint conditions, giving results which either are incompatible with the chemistry of the system or do not satisfy material balance requirements. Also the path of decarburization was found to vary even for heats made under apparently identica1 conditions. A promising approach to analyzing the decarburization results is to relate oxygen efficiency fm carbon removal to bath carbon content. This relationship for Fe-C heats shows the same range of oxygen efficiencies as is obtained in pilot-plant and commercial heats using hot metal-scrap charges. This implies that oxygen transfer is primarily controlled by the decarburization reaction itself, independent of other refining reactions. Therefore, it should be possible to study separately decarburization and slag-metal reactions. DECARBURIZATION is probably the most important reaction in steelmaking. Not only is it a main reaction in the refining of iron to steel but it also provides the stirring action in the bath necessary for the diffusion processes to proceed at reasonable rates so as to make a steelmaking process practical. Kinetics of decarburization in the open-hearth process has been a subject of investigation for many years.&apos;-B It is generally accepted that at steelmaking temperatures the rate of homogeneous C-0 reaction is extremely high and cannot constitute a rate-controlling step. Diffusion of oxygen through a boundary film in the metal phase has been suggested by arken&apos; as rate-determining. Recently, Larsen and sordah16 concluded from experiments in a laboratory furnace that, with oxygen supplied from air or combustion gases, the rate of "steady-state" carbon boil is controlled essentially by a diffusion process of O2, Co2, or H2O through a film of nitrogen above the slag surface. Displacing this diffusion film by a stream of nearly pure oxygen produced a ten-fold increase in the rate of carbon boil with the rates of slag-metal oxygen transfer, bubble nucle-ation, and other steps all apparently able to keep pace. In the top-blown basic oxygen process, however, the transport of oxygen takes a more direct route. and the state of bath agitation is much more turbulent than in the open-hearth process. In addition, direct contact of the gas with the metal phase provides opportunity for direct oxidation of carbon. It is likely that the rate-limiting factor for the decarburization reaction will be different. However, only a few descriptive discussions of the subject have been reported in the literature.10-l2 Studies of the decarburization kinetics based on plant or pilot-plant data are necessarily complicated and are influenced by other refining reactions which occur simultaneously. In order to investigate the mechanism of decarburization, experiments have been conducted in which carbon-saturated iron melts were top-blown with pure oxygen over a range of conditions. It is hoped that this study will form a foundation on which a more basic understanding of this important reaction may be built. EXPERIMENTS One group of blowing experiments was made in a standard 200-lb induction furnace and another group in a 500-lb induction furnace. The furnaces were modified to the general shape of a basic oxygen furnace by adding a rammed refractory cone section to the regular crucible body. Crucible and cone were of high MgO (95 pct) material. A water-cooled lance, 1/2 in. in diam and threaded at one end to take a nozzle, was used for blowing oxygen. The lance with its water and oxygen lines was supported on a cantilever arrangement so that it could be moved up, down, or sideways. Oxygen of 99.5 pct purity was supplied from a cylinder and metered through a rotameter equipped with pressure and temperature gages. Another pressure gage was located at the top of the lance. A schematic diagram of the assembly is shown in Fig. 1. Before each experiment, a weighed amount of ingot iron, containing 0.02 pct C, < 0.01 pct Si, 0.10 pct Mn, 0.019 pct P, and 0.015 pct S, was charged in the furnace and melted down by induction heating. Graphite was then added to the molten charge until it became saturated. When the temperature of the charge reached the desired level, the lance was lowered to a predetermined height above the bath

Jan 1, 1964

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,&apos; and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.&apos; The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

[ ]

Jan 1, 1938

By W. A. Boyer

HOISTS for metal mines are seldom designed for H one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper.

Jan 10, 1954

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,&apos; for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.&apos; They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

E. Hill, South Norwalk, Conn. (communication to the Secretary*) :—The phenomenon described by Dr. Ledoux, involving an apparently abnormal high temperature in the air-cylinders of compressors, has not been, so far as I know, discussed in technical literature. The common formula for the adiabatic compression of dry air does not account for heat suficient to flash ordinarily decent cylinder-oils, nor do the text-books include in their theoretical statements any quantitative consideration of the effect of leaks in the ideal machines which they contemplate. This lack I have endeavored to supply by preparing, in the form of a circular, for the use of the customers and correspondents of the Norwalk Iron-Works, a brief mathematical

Jan 1, 1904

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower&apos;s control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower&apos;s stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower&apos;s pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By AIME AIME

WILLIS McGERALD PEIRCE-"Jerry" to his host of friends, and on that account a hit of a puzzle to those who have known him only as "W. 14."-a native of Buffalo, educated at Penn State College, Illinois: and Yale universities, has bee11 associated throughout all of his professional career with the New Jersey Zinc Company. Jerry has served successively as investigator, section chief, and division chief in the research department of the company and has just been promoted to chief of research.

Jan 1, 1937

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette&apos; recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.&apos;."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy&apos;s law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By H. J. Donnell, B. C. Parks, O&apos

In 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen&apos;s terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.1 The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O&apos;Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogena-tion properties of certain American coals. In the years following adoption of Thies-sen&apos;s method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau&apos;s method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O&apos;Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring in-strumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. Petrographic Components and Type Classification of Coal Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1949

By E. L. Brack

ASARCO&apos;s copper smelter at Hayden, Arizona has been upgraded to meet the increasing Environmental Protection Agency (EPA) and Occupational Safety and Health Administration (OSHA) environmental standards. Fortunately, means were found to accomplish these standards and provide for more efficient operations. With the adaptation of oxygen flash smelting and other related operations at Hayden, ASARCO has turned to the use of minicomputers and microprocessors for inter-plant communications and local area process control. The applications of distributive and computer controls to the plant operations at the Hayden smelter are discussed in this paper.

Jan 1, 1984

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

By Rossiter W. Raymond

THE most important event in the history of mining in the United States was the discovery of gold in California, which led to the rapid development, not only of a new industry, but of a new empire. The settlement of the Pacific slope was making but slow progress under the inducements of a scanty commerce in furs and hides. The liberal grants offered by the government to agricultural pioneers in Oregon had attracted to the Willamette valley and other favored points in that territory a limited population; but the government of the Mexicans in California was positively unfavorable to enterprise. It is true that gold was known to exist in the country. Rumors of it were current among the trappers, and placers had actually been worked in what is now Los Angeles County ; but the padres of the neighboring mission of San Fernando had discouraged the business as demoralizing to their flocks ; and the existence of the precious metal was not widely known; still less was its distribution north¬ward suspected. The discovery of gold, January 19th, 1848, at Sutter&apos;s saw-mill, on the south fork of the American River, afterward famous as Coloma, in Eldorado County, was the beginning of the new epoch. This discovery was made by James Wilson Marshall, a partner in the mill, who observed in the debris washed down by the tail-race a glittering fragment of a mineral unknown to him. Suspecting it to be gold, he sought for further specimens, and obtained, in the course of a few days, several ounces of it. Tests subsequently

Jan 1, 1875

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By Kim Beattie

IN spite of the fact that in 1944 Canada experienced a decline in production of all her leading base metals-nickel, zinc, lead, and copper; despite uncured headaches in the coal-mining industry; and cheerfully ignoring a still further drop in gold, the most valuable product of her mines, which had the lowest output of any year since 1931, the Canadian miner retains the traditional optimism of miners everywhere as he looks forward to the postwar period. Some factors should keep the Canadian mining industry from being too optimistic of the coming era of peace, but the fraternity generally holds that its confident attitude towards the future is based on sound reasons. The decline in production in the Canadian mining industry last year can be almost wholly attributed to the serious shortage of labor and the difficulty in obtaining transport and supplies in remote areas. Some falling off occurred in the demand for certain strategic metals, but the diversion of gold miners, especially, without replacements being obtainable, to direct war work or allied pursuits, was certainly the principal cause of the reduced output in 1944. But that is a situation which will right itself at the close of the conflict.

Jan 1, 1945

By R. J. S. Brown, B. W. Ganison

A new logging method has been developed, based on measurement of the nuclear magnetism of formation fluids. The nuclear magnetism log (NML) is the only log that responds solely to formation fluids. It operates equally well in both oil-base and water-base muds and in empty holes, and can be used in all kinds of formations except strongly magnetic ones. Two separate NML measurements can be made, one of which provides a continuous formation fluid curve. This fluid curve is called the free fluid log (FFL) and is believed to indicate a minimum effective porosity in most formations. The FFL not only delineates fluid-containing zones, but provides an excellent correlation curve that can be obtained under conditions where conventional correlation logs are ineffective. Preliminary tests indicate that the second kind of NML measurement may help distinguish oil and water zones and provide information concerning permeability and wettability. (The FFL itself appears to provide some information on permeability.) The second kind of NML measurement requires stopping the logging tool for a short time opposite a zone of interest and taking more extensive NML data that can be displayed as nuclear magnetic relaxation curves. In some instances, oil and water saturations for the region immediately adjacent to the borehole can be read from these relaxation curves. INTRODUCTION In 1946, Bloch, Hansen and Packard and Purcell, Torrey and Pound3 independently announced the successful demonstration of the phenomenon of nuclear magnetic resonance. During the past 13 years, there have been many applications of nuclear magnetic resonance, including applications to the study of chemical structure and to the measurement of magnetic field strengths. Preliminary experiments on the feasibility of using nuclear magnetism measurements in well logging were made independently by California Research Corp. and Varian Assoc., the Varian work being sponsored by the Byron Jackson Tools, Inc. Since then a cooperative research program on nuclear magnetism logging has been carried out by the Byron Jackson Div. and Research Center of Borg-Warner Corp., and California Research Corp., subsidiary of Standard Oil Co. of California. The use of nuclear magnetism in well logging is of special interest because it offers a way of making direct measurements on the hydrogen in the formation fluids and not on the rock matrix. Within the past 1 1/2 years, successful measurements have been made with a research model logging tool in wells in California, Tex as, Utah, Louisiana and Wyoming. NUCLEAR MAGNETISM SIGNALS Polarization, Relaxation and Precession Many atomic nuclei possess magnetic moments and spins; that is, they are similar in some respects to bar-magnet and gyroscope combinations. Molecules and their nuclei are subject to thermal motion, which has a scrambling effect, tending to leave as many nuclear spins oriented in any one direction as in any other. However, if a magnetic field is applied, the magnetic nuclei tend to align in the direction of the field. The scrambling and aligning forces compete with each other, with the result that a few more spins are oriented parallel to the field than in other directions. This gives a net magnetization, or polarization, which is directly proportional to the strength of the applied magnetic field (aligning influence) and inversely proportional to the absolute temperature (scrambling influence). When the magnetic field in, or temperature of, a liquid sample containing protons is changed, the new equilibrium value of proton polarization is not established immediately but requires an amount of time which depends on the nature of the hydrogen-containing materials. The process of approaching the equilibrium value of polarization is called relaxation.&apos;.&apos; Polarization is a vector quantity, and the components parallel to and perpendicular to the magnetic field must be considered separately. Relaxation of the component parallel to the field is called "thermal relaxation", or "longitudinal relaxation", and the corresponding time for this component of non-equilibrium polarization to decay by a factor of e (natural log base) is denoted T. The relaxation of the perpendicular component is called "transverse relaxation", and the corresponding relaxation time is denoted T,. The potential energy of a magnet in a uniform field depends on the angle the magnet makes with the field; therefore, a change of the component of net polarization parallel to the magnetic field involves an exchange of energy between the spin system and the thermal motion of the molecules, leading to the term thermal relaxation for the relaxation of this component. Suppose we subject a sample to a strong magnetic field at right angles to the earth&apos;s field for a time greater than TI. A polarization, thus, is established at right an-