Search Documents

By J. E. Johnson

IT is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence in these respects on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control; the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in d practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the toll-gases, and that the ratio of CO to CO., will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Sep 1, 1905

By B. DE MARE

THE No. 6 open-hearth furnace at the plant of the Worth Steel Co., Claymont, Del., is the first to be rebuilt according to the Kuehn system. This as well as the other five furnaces at Claymont, has a nominal capacity of 75 tons, but the actual charge is about 242,000 lb. No hot metal being available, the pig-iron is charged cold. Oil of low grade with an asphalt base is used as fuel. These two items have to be kept in mind when discussing the actual fuel consumption. Careful records have been kept covering a five weeks run and the following is a brief summary of them The time required to heat the furnace preparatory to charging from the time a wood fire was started until charging commenced was 36 hours. This, I understand, is much less than with furnaces of standard design. The draft of the furnace, as shown by a gage in the stack-flue, is 1.25 in. The maximum draft with new checkers on former runs was 1.50 in., this draft gradu¬ally decreasing as the checkers closed up. Both of the first helpers claim the present draft is all they need for the proper working of the furnace, and, as with the Kuehn regenerators the draft remains practically the same from beginning to end of a run, this is satisfactory.

Jan 1, 1929

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By Paul E. Melancon, Vincent C. Kelley, Dale F. Kittel

Uranium of the Grants region occurs predominantly in continental sandstones of the upper part of the Jurassic Morrison Formation, but significant lesser deposits are found in limestone of the Jurassic Todilto Formation and in black shale of the Cretaceous Dakota Formation. The deposits are disseminations that form runs ranging from a few hundred tons to several million tons. The ore consists mainly of uraninite, uraniferous carbonaceous material, coffinite, and such secondary oxidized minerals at tyuyamunite, carnotite, and uranophane. In sandstone, the ore runs were locallized by mudstone, interstitial carbonaceous material, and primary sand channel trends. In limestone, ore deposition was related to folds and fracture zones. The great bulk of production has come from the Ambrosia Lake mines in the Grants district and the Jackpile and Paguate mines in the Laguna district. The ores, which generally have been 0.20 to 0.30 per cent U3O8, are treated at mills operated by Kerr-McGee Corporation, Homestake-Sapin Partners, and The Anaconda Company, all in the Grants district. In 14·years after discovery in 1950, the deposits had yielded concentrates valued in excess of $800,000,000. Since deposition of the Jurassic host rocks, a geologic history involving tilting, faulting, erosion, changing ground-water environments, and oxidation has considerably influenced the existence and character of the deposits. It is evident that their ongm is not simple. However, a degree of agreement appears probable for a pre-Dakota age for the original ore runs, and, at Ambrosia Lake, two principal stages of ore formation, separated by Laramide faulting, are recognized. All earlier ores have been modified by Quaternary oxidation, solution, and enrichment during which time much secondary tyuyamunite, metatyuyamunite, carnotite were formed.

Jan 1, 1968

By W. E. Wrather

DURING the war the mineral industry, and metal mining in particular, extended itself more than any other to attain the limit of its productive capacity. Likewise, probably no other industry went quite so far toward jeop¬ardizing its own economic future through depletion of material reserves. Once we looked to Europe for most of the manufactured goods we needed. Our own limited mineral requirements were easily supplied from mines near the Eastern seaboard. With expansion and industrialization, our mineral needs increased in proportion, and the centers of mining activity moved westward to Michigan, Wisconsin, Minnesota, and the Tri-State district, where seemingly inexhaustible high-grade deposits of iron, copper, lead, and zinc ores were opened and rapidly developed.

Jan 1, 1946

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By DR. RICHARD RATHBUN

(Washington Meeting, May, 1965.) THE remarks of Dr. Rathbun in his address of welcome render it unnecessary that I dwell either upon the history or aims of the National Museum, and enable me to proceed at once with a brief descriptive outline of the Department for which I am responsible, and this with particular reference to that division devoted to applied geology. The amount of geological material brought together prior to 1876, under the various Congressional acts quoted, was, though valuable, comparatively small. It consisted mainly of the collections made by Professor J. D. Dana and his assistants during the Wilkes Exploring Expedition; by the various geologists accompanying the surveys of the Pacific railroads in 1854-55; the Surveys West of the 100th Meridian under the direction of the Engineering Corps of the Army; the United States geological surveys under direction of Dr. F. V. Hayden ; and the various Land Office surveys. Prior to 1873 there were no paid assistants to care for these collections. They were studied, if studied at all, by " collabrators," so-called, several of whom had offices and even sleeping apartments in the Smithsonian Institution. In the list of these collaborators are found such names as Conrad, Cope, Gabb, Leidy, Lesquereux, Meek, and Newberry. The building now occupied by the National Museum was designed primarily to make room for the great mass of material secured in 1876 at the close of the Centennial Exposition in Philadelphia. As completed in 1880, it afforded opportunity for expansion and incidental organization on much more practical basis than had previously existed. This found expression in the creation of numerous departments with salaried officials to take charge of the various collections. With the appointment of Dr. George W. Hawes to the position of Curator of Geology and Mineralogy, in 1881, and Dr.

Jul 1, 1905

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By Arthur W. Gray

The thermal analysis of a metal or an alloy is ordinarily made with the aid of heating and cooling curves in which transitions are indicated by the rapid changes in curvature that accompany changes in the rate of heat absorption or evolution. Analysis by the method that depends on the change in thermal expansivity is not customary, partly, at least, because of the difficulties involved in making the necessary measurements. However, under certain circumstances, the dilatometric method of analysis may possess advantages over the thermometric method that will justify the additional trouble required. The addition of 1 per cent. of zinc to an alloy has been found to produce upon the volume changes that take place during transition effects that suggest the possibility of using the dilatometric method of thermal analysis as a rather sensitive means of obtaining chemical information. Although the illustrations presented in this paper are drawn from data obtained during an investigation of dental amalgams, similar phenomena can doubtless be observed with other alloys. Some of the results found during an investigation made in 1917l have been confirmed by data on the thermal expansivity of amalgams published by Souder and Peters of the Bureau of Standards in reporting tests of dental materials.2 Although the Bureau of Standards made experiments for the purpose of discovering effects of including zinc as one of the constituents of a dental alloy—a matter much discussed in dental literature but without the presentation of reliable experimental evidencae to support the views of either side—the reports of the tests made by the Bureau give the impression that certain striking phenomena associated with the presence of zinc were not noticed. Among such phenomena arc those connceted with the conditions that determine whether or riot a specimen of amalgam becomes covered with droplets from which crystals develop.

Jan 1, 1921

By AIME AIME

ATER the preliminary registration at which approximately 380 members and guests were registered, the 138th meeting of the Institute was opened in the Concert Room of the Palace Hotel. E. A. Hersam, chairman of the San Francisco Section, voiced a brief welcome and introduced F. W. Bradley, president of the Institute, who presided over the remainder of the morning session. After expressing the welcome of the Institute to the members and guests, he read a telegram from Secretary H. Foster Bain, extending the best wishes of the eastern staff and members for a successful meeting. He next introduced Theodore J. Hoover, dean of the School of Engineering, Stanford University, who read an address by the Secretary of the Interior, Ray Lyman Wilbur, briefly outlining California's part in the mining industry and giving the welcome of California to this meeting of the Institute.

Jan 1, 1929

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives' of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are 'still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

By Joseph Hartshorne

This plant is situated in the borough of Pottstown, on the banks of the Schuylkill river, between the Philadelphia and Reading Railroad and the Schuylkill Division of the Pennsylvania Railroad, on a plot of about 125 acres, most of which is reserved for future extensions. About 45 acres are to be used for houses, 40 of which have already been built. The accompanying plan will give a clear idea of the general arrangement of the works. Beginning at the lower or eastern end, the first building is the basic-cinder grinding-plant. At present, it consists of a 2000 mm. Jenisch ball-mill (Kugelfallmühle) similar to those used so extensively for grinding basic cinder in Europe. It was built by Herman LÖhnert, of Bromberg. The mill is very simple in design, and efficient in execution. About 13 horse-power is required to run it, and the average output is 20,000 pounds in 10 hours. The best work we have done is 29,000 pounds in 10 hours, with perfectly dry cinder. From 95 to 98 per cent. of the product will pass through a sieve with 100 meshes to the inch, while from 70 to 75 per cent. will pass through a 150-mesh sieve. The mill has been in service since last March, part of the time on double-turn, and the renewals and repairs have been very slight. The product of the plant is sold as a fertilizer. It runs from 18 to 24 per cent. in phosphoric acid, about 14 of which is reverted. The merits of this fertilizer were explained by Mr. W. H. Morris, at the Baltimore meeting of February, 1892 (Trans., xxi., 232), and by Mr. W. B. Phillips, at the Birmingham meeting of 1888 (Trans., xvii., 84). The results obtained by its use in Europe, where over 600,000 tons were used last year, are well known. Near the cinder-grinding plant will be situated the new machineshop, which is now being erected. The next buildings contain the brick-making plant and ovens.

Jan 1, 1893

By Arthur Hockman, Howard W. Jaffe, Howard F. Carl

THE problem of establishing practical techniques for evaluating natural corundum ores arose from the desire to improve the existing purchase specifications for crystal corundum procured by the Federal Government for stockpiling. Such purchase specifications had been developed for a large number of products, including minerals and ores considered to be critical and strategic because of the country's dependence on foreign sources of supply. It will be apparent to anyone considering the subject of purchase specifications that the determination of whether or not a submittal meets the specifications is a prime consideration. Consequently satisfactory specifications for minerals should not only incorporate physical, chemical, and mineralogical requirements that are practical but should also establish the means by which both buyer and seller can be assured that materials meet stated requirements. The Munition Board's Material Purchase Specification for corundum, dated February 1954, covered two grades of crystal corundum intended primarily for abrasive use. It established limits of size and of composition: Grade A, at least 95 pct +3 mesh and 92 pct alumina (Al2O3); Grade B, at least 95 pct +7 mesh and 90 pct alumina. It also specified that "of each lot of material, not less than 95 percent shall have a hardness equal to or exceeding nine (9) on Moh's Scale." These specifications were unsatisfactory for several reasons. They did not allow the purchase of lower grades of corundum being used by industry. Neither did they specify exactly what a corundum ore actually was, except that it should contain so much alumina and have a certain scratch hardness. Nothing was said about the abrasive qualities of the material that was to be purchased primarily for abrasive use. During the period 1946 to 1948 supplies of the two grades defined in the then current specifications continued to decrease. Early in 1949 industry recommended that the finer sizes of corundum known as "crystal corundum concentrates," ¼-in. to 16-mesh material, be added to the stockpile specifications and that lower grades of crystal corundum also be included. In the spring of 1949 the National Bureau of Standards and the Bureau of Mines were asked by the Munitions Board to cooperate in developing more practical specifications for grading natural corundum ores. The National Bureau of Standards indicated that it would investigate physical test methods for determining abrasive characteristics of corundum, and the Eastern Experiment Station of the Bureau of Mines at College Park, Md., stated that it would consider the mineralogical aspects of the problem. Members of these two agencies, in consultation with representatives of the Office of Materials Resources of the Munitions Board and of the Federal Supply Service of the General Services Administration, and with the cooperation of industrial suppliers and consumers of abrasive corundum, developed, in a fairly short time, more practical specifications for six grades of corundum ores. The new specifications, issued January 1951, were for corundum, natural crystals, as by this time high-purity synthetic corundum was available and widely used. Nevertheless, for certain specific applications the natural product was preferred over the synthetic material. It has been extensively used in forming snagging wheels. It breaks into more or less cubical particles, whereas artificial corundum fractures into splintery shapes. These produce irregular cuts in glass, while the more symmetrical shape produces a more uniform ground surface. For this reason natural corundum has been preferred for certain types of lens grinding. Pure corundum is clear, colorless alpha alumina (A12O3), but it is rarely found in nature in this form. The most important gem varieties include the blue and yellow sapphires and the ruby. Minute impurities of titanic oxide impart a blue color,

Jan 1, 1955

THE hall of the Western Iron and Nail Associations having kindly been placed at the service of the Institute, the opening session was held at 3 o'clock, Tuesday afternoon, May 13th, with an attendance of about one hundred and twenty-five members. Mr. William Metcalf, of Pittsburgh, read an address of welcome on behalf of the Local Committee of Arrangements, to which President E. B. Coxe responded. The following papers were then read and discussed : Regenerative Stoves; a Sketch of their History and Notes on their Use, by John M. Hartman, of Philadelphia. Some Curious Phenomena Observed on Making a Test of a Piece of Bessemer Steel, by William Kent, of Pittsburgh. On the Use of Determining Slag Densities in Smelting, by Thomas Macfarlane, of Wyandotte, Michigan. After the reading of these papers each member was presented by the Local Committee with a schedule of excursions, a specially prepared map of Pittsburgh and surroundings, and a directory of industrial works, all tastefully bound, and also with a metal badge bearing the seal of the Institute, to be worn on the excursions. The second session was held on Tuesday evening. The following persons, duly proposed for members and associates of the Institute, were, on the recommendation of the Council, unan¬imously elected. (In this list are included those elected at the final session on Friday morning.) George Bartol, - Cleveland, Ohio. Luther S. Bent, - Steelton, Dauphin Co., Pa. Octave Chanute, - New York City. Albert H. Childs, - Allegheny, Pa. Theodore Cooper, - New York City. Andrew Cosgriff, - Brewster, Putnam Co., N. Y. William B. Crocker, - New York City. Henry M. Curry, - Pittsburgh, Pa. Charles Davis, - Allegheny, Pa. Henry F. De Bardeleben, - Birmingham, Ala. Herbert Du Puy, - Pittsburgh, Pa. Charles L. Fitzhugh, - Pittsburgh, Pa. W. S. Franklin, - Ashland, Md. F. G. Fricke, - Pittsburgh, Pa. Paul A. Fusz, - St. Louis, Mo. Ignatius Hahn, . Pittsburgh, Pa. Henry Hargreaves, - South Pittsburgh, Tenn.

Jan 1, 1880

By R. W. Jenkins, O. J. Neslage

The need for mechanized drilling to decrease mining costs has resulted in the development of the jumbo from column-and-bar drill carriages to hydraulically controlled jib jumbos. Resultant savings from use of improved jumbos have been high enough usually to retire the machinery investment within a year. The jib jumbo unit has been applied successfully to development and preparation programs and flat-bedded stopes, and an even wider field is forecast for its use.

Jan 1, 1950

By John M. Kelly

This report covers the development, exploratory drilling, and production of oil and gas in New Mexico during 1945. The statistical information was gathered from state regulatory agencies and other sources believed to be reliable; it is presented here in combined form for general information only, and the author assumes no responsibility for its accuracy or completeness.

Jan 1, 1946

By W. P. Lass

The gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co., Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About 3 or 4 tons of this precipitate is produced monthly having 'a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the byproducts from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 1b. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high. The upper electrodes, of graphite or carbon, are 3 in. in diameter and 40 in. long, arranged with joints enabling new electrodes to be connected without shutting down or wasting stubs. A screw feed was arranged for raising and lowering the upper electrode. (Figs. 1 and 2.) The cover for the furnace had three openings, one for feeding the charge, one for the escape of gases, and one in the center for the introduction of the electrode. It was later found more practical to enlarge this center opening to 6 in. in diameter, to allow of a central feeding of the charge around the electrode.

Jan 1, 1916

T. M. Drown, South Bethlehem, Pa.: Mr. Thackray's paper shows in a striking way the high degree of rapidity and ac curacy exhibited by the chemists of our steel-works in ordinary everyday practice. That determinations made in an hour should present only slight differences in the third place of deci male is certainly matter for surprise and congratulation. This remarkable result has been due, perhaps, in part, to a remark able cause. The managers of works, ignorant of all the diffi culties of the laboratory, have demanded "the impossible " of their chemists—and the chemists have done it! Andrew A. Blair, Philadelphia, Pa.: Mr. Thackray's paper is extremely interesting, especially in its bearing on the question of a standard method for the rapid determination of phosphorus in the laboratories of steel-works. Before discussing the re sults in general, I desire to explain the results obtained by me under method A'. This is the method which I have used in the work of the sub-committee on Methods of the Interna tional Steel Standards Committee. It may be described briefly as follows: Solution in nitric acid; oxidation of carbonaceous matter by permanganate; precipitation of phosphoric acid by molybdate solution; reduction of molybdic acid in the reductor, and titra tion by permanganate. This method was used apparently by only three chemists, Dr. Dudley, Mr. Crowell, and myself. In determining phosphorus by this method, among the most essential points to be considered are the ratio of iron to molyb dic acid, or the reducing action of zinc on molybdic acid as compared to its reducing action on iron, and the ratio of molyb dic acid to phosphorus in the ammonium phospho-molybdate obtained by precipitation from the solution of the steel. In regard to the first point, the usually accepted ratio is 1 to 0.90756, or, as it is roughly stated, 0.9076, which is based on the assumed reduction of the molybdic acid to Mo12019,. This

Jan 1, 1896