Search Documents

By E. C. IBBOTSON

THIS process was reported upon by the Canadian Commission in 1904, and much detailed information was also given in a paper by Chief Engineer V. Engelhardt.1 Believing that some of the latest particulars of the process will be of interest, I submit the following data. At Gysinge in Sweden during the year ending May 31, 1906, from a fixed furnace giving 1 ton (2,240 lb.) of steel per tap, there were produced 950 tons of tool-steel and special steel ingots. . In carbon and iron tool-steels all the usual tempers were made. The bulk of this steel was made from charges composed of about 80 per cent of Swedish white pig-iron and 20 per cent. of steel-scrap. The percentage of carbon was regulated by the addition of briquettes. Other charges were made from Swedish white iron and steel-scrap. The average time taken per charge, for the year, when adding briquettes, was 7* hr., and the electric energy consumed was 1,128 units (kilowatt-hours) per ton. The average time per charge for white-iron and scrap charges was 5.5 hr., and the electric energy consumed was 886 units per ton. These consumptions include all time and energy lost from various causes, such as bad water-supply, ice, etc. It is quite ordinary practice to complete the charges with briquettes in 6.5 hr., and without briquettes in 5 hr., as shown by the following typical charges White pig-iron, 1,457; steel-scrap, 439; briquettes, 220; ferrosilicon (50 per cent. of silicon), 17 ; ferromanganese (80 per cent. of manganese), 15 lb. ; and aluminum, 1 oz.=

Nov 1, 1906

By R. F. Marande, R. S. Busk

THE magnesium-aluminum-zinc system contains most of the magnesium-base alloys used commercially, although in practice the ternary, alloys are usually modified by the addition of a small amount [ ] of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the object of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.1 [ ] All alloys reported were made in 15-lb. melts, superheated to 1700°F. for 15 min., cooled to 1400°F. and poured in sand molds. The test bars produced had a ½ in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. CONSTITUTIONAL DATA Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914

By Fred DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force? of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are inter-esting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or, elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determina-tion of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By Arthur S. Coffinberry, Ralph Hultgren

We have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, combined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atoms, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such information is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By Arthur S. Coffinberry, Ralph Hultgren

We have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, combined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atoms, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such information is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

By Edward Norton

THE -salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Ouachita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By Thomas Read

SUMMARY THE cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; lie is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and metallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work1 I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 2, 1918

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent;, a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By Charles B. Dudley

While working, during the summer of 1877, upon the "Chemical composition and Physical Properties of Steel Rails," the results of which are given in my report with this title, I was struck with the surprising wear which some of the rails, which would ordinarily be called soft rails, had endured. At that time I knew of no chemical measure of softness except low carbon, and I found that a numher of rails with low carbon had endured as high or higher tonnage, with apparently as little loss of metal by wear, as those with higher carbon. My own work on steel rails that summer did not embrace any definite experiments as to the amount of metal worn off the rail per million tons which had passed aver it; and so I could get no more definite answer from that work, to the question at the head of this paper, than was given by comparing the appearance of the worn section of the rail with its tonnage. This comparison, however, served to arouse in my mind the query, whether the commonly received opinion as to the relation between the hardness and wearing power of steel is correct, as applied to steel rails. This opinion, if I am right, is: the harder the steel, the better will be the wear, and the limit of hardness is simply one of safety; hard, brittle steel being, of course, more liable to break than soft, tough steel. The query, although aroused, did not bear any immediate fruit, and, as will be evident to any one reading it, the report above referred to was written with the commonly received opinion in mind. Since that time I hare collected a little information upon this subject, which I should be glad to submit to the Institute, if for no other purpose, for the sake of arousing attention, and directing study to the question of hardness versus wear in steel rails. Before making known this information, howevcr, permit me a few words in reference to hardness. How shall we measure the hardness of steel ? Of the various ways of getting indications as to the hardness of steel, which are known, three mill serve our present purpose. These are: 1st. High carbon. It is generally agreed, I think, that at least within proper limits, the greater the amount of combined carbon in a piece of steel, the harder the steel, and I need not do

Jan 1, 1879

Discussion of the papers of FREDERICH LAIST and HAROLD W. ALDRICH, FREDERICH LAIST and F. F. FRICK, W. L. AUSTIN, and STUART CROASDALE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletins No. 91 and 92, July, and August, 1914. R. C. CANBY, Wallingford, Conn. (communication to the Secretary*). -Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and coke, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata., it might be of interest to refer briefly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911, I. gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcome after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable-chlorine, clue to the imperfect conversion of the subchloride to suboxide, as well as that clue to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted With the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These, fumes had a peculiarly suffocating effect, so that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been clue to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 11, 1914

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By John F. Brass

INTRODUCTION The Jim Walter Corporation is a Florida based organization with diverse interests. They have operations in many states and overseas, but the heart of the company is in the southeast. The major part of the corporation's business is home building and everything that is related to it. In 1969, the Jim Walter Corporation gained an interest in coal mining through the acquisition of the U. S. Pipe & Foundry Company which had two slope mines to supply its requirement of metallurgical coal. In the early 1970's it was decided to enlarge the coal mining activities and work was started on the Blue Creek project. This involved sinking four new deep mines (originally there were to have been five but it was later decided that the property could be satisfactorily worked by four mines). They are all located in west central Alabama between Tuscaloosa and Birmingham. They have a combined projected output of 7314 million tons of very high grade metallurgical coal per year to be reached by the mid 1980's. These new mines are all to work the Blue Creek seam which is a very gassy seam and in the area to be mined is found at between 45m (1500 ft.) and 731m (2400 ft.) below the surface. Longwall is the only practicable method of mining to produce the planned outputs in the conditions prevailing and each mine is planned to have three longwalls as the primary production system. Continuous miners will be used just to do the development work for the longwalls. No. 3 Mine is the most advanced of the mines and started the first longwall early in 1979. The second unit started in the middle of 1980 and the third is scheduled for mid 1981. The first longwall at No. 4 Mine is expected to commence production early in 1982. This paper attempts to relate some of the problems that have been encountered and the lessons that have been learned.

Jan 1, 1981

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

Edward Payson Mathewson EDWARD PAYSON MATHEWSON, President of the American Institute of Mining and Metallurgi-cal Engineers, was born in Montreal, Canada, Oct. 16, 1864, of Scotch-Irish ancestors. After preparation in private and public schools, he graduated from McGill University with the degree of Bachelor of Applied Science, in 1885, having specialized in mining engineer-ing and metallurgy. He spent the succeeding summer as a surveyor with the Canadian Geological Survey, being employed in the lake region of Ontario. The following spring he left Canada for Colorado, where he immediately obtained a position as assayer with the Pueblo Smelting & Refining Co. Within three years he became superintendent of the plant, and his success in this position brought him to the attention of the Guggenheim family, whose employ he entered in 1897. He was first in charge of their Pueblo plant, but was soon transferred to their refinery at Perth Amboy, N. J. During the succeeding five years he was in charge of important smelting operations conducted by the firm in Mexico and South America. In June, 1902, Mr. Mathewson accepted a position at the Washoe reduction works at Anaconda, soon thereafter becoming manager of the property. It is unnecessary to recount the improvements and enlarge-ments instituted at that plant under his management, until it became the Mecca of all metallurgists visiting the United States. The esteem in which Mr. Mathew-son was held, not only by the men directly under him, but by all his fellow citizens, was expressed in a send-off such as probably no other plant manager has ever received, when he left Anaconda in October, 1916, to accept the general managership of the British America Nickel Corporation, at Nickelton, Ont., Canada. Soon thereafter Mr. Mathewson accepted an appoint-ment as director of the American Smelting and Refining Co., acting as consulting metallurgist for the company and its subsidiaries. In November, 1919, he resigned this position and opened an office in New York City as a consulting metallurgist.

Jan 3, 1923

By K. A. Jackson, J. D. Hunt

The discussion by Tammann and Botschwar of the transition from eutectie grouth to denrdritic plus eu-tectic growth is reviewed and applied to metallic eutectic systems. Using expevimental data on the geowth rate of the Pb-Sn eutectic, and an extrapolalion of dendritic growth rate in tin and Sn-Pb alloys , qlcantitatice prerlictiotls of the extent of the eutectic region in tin-vich Sn-Pb alloys are made. There are no experimenta1 measuvements available for detailed comparison with these predictions. EUTECTIC structures form over a small range of compositions. The theory of lamellar growth presented by Jackson and Hunt' indicates that it is in principle possible to have eutectic growth over almost the complete range of compositions between the two solidus lines. This does not occur in practice. Alloys far from the eutectic composition grow dendritically followed by a eutectic as shown in Fig. I. The transition from a eutectic to a dendritic plus eutectic interface cannot be predicted from constitutional undercooling arguments because constitutional undercooling always exists ahead of the eutectic interface.' Reasonable predictions can, however, be made using arguments originally put forward by Tammanl. and Botschwar.3 These and later workers'"*6 carried out extensive experimental investigations of the extent of the eutectic range in organic materials. They concluded that the structure formed, eutectic or dendrites plus eutectic, depended on which structure grew faster at the given undercooling. This is, of course, equivalent to the structure which grows with the smallest undercooling at a given growth rate. In this paper, we will discuss these ideas briefly and then apply them to predict quantitatively the range of eutectic growth in tin-rich Pb-Sn alloys. The temperature dependence of the growth rates of dendrites and eutectic for a typical metal alloy of eutectic composition is shown schematically in Fig. 2(a). The growth rate for the eutectic increases more rapidly with undercooling than those of the dendrites because of the short diffusion path maintained in the eutectic, see Fig. 1. For an alloy off the eutectic composition on the A-rich side, the growth rates shift as shown in Fig. 2(b). The liquidus temperature of the a phase increases, that of the 3 phase decreases, and the temperature of zero growth rate for the eutectic does not change. The curves, particularly the dendritic ones, change shape as well, but for our purposes the principal effects occur because of the change in liquidus temperatures.3-6 In an isothermal system, only a dendrites will grow above TE, Fig. 2(b). If the temperature is below TE, and both phases have nucleated, a dendrites will grow ahead of the eutectic at

Jan 1, 1968

By A. F. Beasley

FROM the initial Bunker Hill smelter operations in 1917, to March, 1930, only 50 per cent of the ore production of the Bunker Hill and Sullivan Mining and Concentrating Co. was handled at this plant. Since the date last mentioned, the total mine production has been received. The old lead refinery was equipped with four 105-ton drossing kettles, three 110-ton softening furnaces, four 105-ton desilverizing kettles, three 100-ton refining furnaces, one 150-ton round refined lead-storage furnace, one 75-ton residue furnace and one hand-operated casting wheel. This equipment, with the exception of the residue furnace, could not adequately handle the increased tonnage in addition to the regular supply of custom ore. It became necessary either to install additional furnaces and kettles or to rebuild the entire plant, installing equipment of greater capacity.. The latter course was chosen, partly because of lack of space for additional equipment but mainly because of the more economical operation of larger units.

Jan 1, 1932