Search Documents

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By R. W. Kraft

The normal Mg-Mg,Sn eutectic is a classic example of a Chinese script eutectic. When the alloy is unidirectionally solidified, a much simpler topo-logical arrangement of the phase particles can be produced although individual grains still usually consist of two or more interpenetrating lamellar systerns. Specimens from unidirectionally solidified ingots were analyzed metallographicall~ and crys-tallographically, and it was found that the interfaces between the lamellae had a common crystallograPhic character describable by: Lamellar interfaces II {220}Mg2Sn 1) {1011}Mg Arguments are presented to explain why this particular orientation relationship tends to occur and it is shown that this criterion can be nearly satisfied simultaneously on up to four different lamellar systerns between two interpenetrating single crystals. Finally, on the basis of this work ad other similar work which has previously been done on Al-CuAl2 eutectics, a general principle pertaining to low-energy interfaces between two crystalline Phases is proposed. WITHIN the past few years several investigators1-4 have demonstrated that the microstructures of many eutectic alloys can be significantly altered by uni- directional solidification. If appropriate control is exercised over the purity of the alloy, the growth rate, and the thermal gradient during unidirectional solidification, ingots can be made in which the phase particles are aligned predominantly parallel to one another throughout substantial portions of the ingot. The present author has also shown for at least one of the alloys that the parallel lamellae tend to assume a unique crystallographic relationship during

Jan 1, 1963

By Young C. Kim

The use of computer models to design the ultimate open pit limits during feasibility studies as well as during long-range mine planning is becoming an enforced practice in all types of mining, e.g., ferrous, non-ferrous, and coal. As a result, the state of the art in computerized ultimate pit limit design methodologies and associated computing and optimizing techniques has advanced considerably in recent years. Unfortunately, very little has been published to date regarding the preferred ultimate pit limit design philosophy, i.e., optimizing us satisfying, or regarding the modeling approaches being used for different types of orebodies. This paper reviews the current state of the art in various modeling approaches and optimizing techniques that are in use for different types of deposits, through available literatures and personal communications.

Jan 1, 1979

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By J. J. Bodmer

The substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pitsand—siliceous sand, as it commonly occurs mixed with gravel—and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order. to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (unslaked) lime with sulphate of lime, or plaster of Paris. The graystone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

By Foster Bain

MOST of us householders in the East burn anthra-cite, so the problem that interests us most is the distribution and supply of the domestic sizes of anthracite. That, however, is only a small part of the coal problem and has its own peculiarities. Whether anthracite prices are high or low is largely a matter of relativity, depending on the size of the transaction, the available supply, and other things. As an isolated example which I hesitate to quote because it is not entirely representative, you may be interested to know that the Government fuel yard has been delivering to the Government buildings in the District of Columbia, white-ash stove coal at 16 c. a ton less during January, 1923, than during the same month of 1922. The reason is that the Government deals only with large companies who have been wise enough not to boost their prices and the small increase at the mine has been more than offset by the decrease in railroad rates. The total cost is $12.50 per ton, but I want to make it perfectly clear that it does not follow that this would be a just price for a retail dealer to charge the domestic consumer. For example, in the Government business there is no such thing as a bad debt, and certain other fixed or general charges are charged to other departments. The Bureau of Effi-ciency made an effort to determine what would be a. legitimate handling charge for a retail dealer, in Washington, and concluded that if the Government's cost of handling was $1.00, then $1.88 would be the corresponding fair charge to pay a retail dealer carrying the same volume of business, allowing for bad debts, complete depletion and depreciation of his equipment, and 10- per cent. profit. Assuming that this is the correct differential for Washington, it does not' follow that it would be equally just for Pittsburgh, New York, or elsewhere; nor does it by any means follow that it is a fair differential this year, because the dealer, after being unable to use his equipment in the summer months, now has to deliver an unusually large quantity of coal. I merely cite this instance to show that on the basis of primary cost of coal plus railway charges the retail price is not necessarily higher this-year than last.

Jan 4, 1923

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953

By H. LeRoy Scharon, A. B. Cleaves

THE application of geophysical techniques in the A engineering surveys of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System is unique inasmuch as this is the first time, (to the authors' knowledge), that such studies have been employed on a large scale on a major highway system. These investigations were confined to specific areas along the center line of the proposed Philadelphia Extension between Carlisle and King of Prussia, and the Western Extension between Irwin and the State line near Youngstown, Ohio, as shown in Fig. 1. Along the 100 miles of the philadelphia Extension, the geophysical surveys were confined to 137 individual cuts and comprised a total length of 37.4 miles of line. The Western Extension, 66 miles in length, has 108 individual cuts. The accumulated length covered by electrical resistivity studies was 17.3 miles. The depth of the cuts varied from a minimum of 10 ft to a maximum of 62 ft. The geophysical investigations were made for the purpose of determining depths to bedrock in the 245 proposed cuts and at the sites of various structures. The 'data also served as a basis for geological interpretations of the condition of bedrock, contact zones, rock types, water table, and other factors significant in highway construction. The geophysical method of investigation employed the use of the electrical resistivity principle using the Gish-Rooney type electrical resistivity meter and the Wenner electrode configuration.* Apparent resistiv- ities were determined for constant intervals to various depths and were correlated with surface geological observations and subsurface geological conditions revealed by key diamond drill holes situated within a given cut interval. From these correlations, depths to bedrock were postulated with notations on other geological features that might be pertinent to modern highway construction. Geology The bedrock underlying the areas of the extensions of the Turnpike afford an excellent academic study of the electrical resistivity depth method as well as a practical application to modern highway engineering. The rocks encountered on the Philadelphia Extension vary in age from pre-Cambrian to Triassic and Quaternary, whereas in the Western Extension, bedrock is confined to relatively flat-lying strata in the Allegheny, Conemaugh, and Monongahela formations of the Upper Paleozoic, Pennsylvanian. Glacial and Recent stream, valley, and terrace deposits are common. Philadelphia Extension The oldest bedrock encountered in this extension are igneous and metamorphic. These, encountered chiefly in Chester County, consist of the strongly

Jan 1, 1952

By James W. Neill

Bituminous coal has for many years been used for the smelting of iron-ores in the blast-furnace. In some districts in Scotland it is used alone, in others it is used mixed with coke. The similar use of certain bituminous coals in the United States has been repeatedly mentioned in the Transactions. (See, for instance, as to the Hocking Valley coal, the papers of Dr. T. Sterry Hunt, Trans., ii., 275, and vii., 313; and as to Indiana "block-coal," the paper of Mr. J. S. Alexander, Trans., i., 225.) Phillips (Elements of Metallurgy, p. 250) says: " Raw coal for blast-furnace use must be of a non-cokiog kind, and, when of suitable quality, is perhaps the most advantageous fuel." In the first

Jan 1, 1892

By W. L. Remick

THE hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past 2 years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co., Pottsville, Pa. This plant is now operating. APPLICATION The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from %2 in. down to and including "dust." (Anthracite passing a 32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes. from 3/8 in. down to "dust. 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and _washing. processes which may be considered outside the realm of coal cleaning. PRINCIPLE OF OPERATION Fig. 1 shows the method of classification practised under the Hydrotator patent:1 In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

By A. M. Ross

DEURING the past year the uranium milling industry has seen the installation and initial operation of solvent extraction circuits in the Climax Uranium Co. mill at Grand Junction, Colo.; the Kerr-McGee Oil Industries mill at Shiprock, N. M.; and the AEC pilot plant at Grand Junction, operated by National Lead Co. Inc. The Vitro Uranium Co. mill in Salt Lake City is converting to solvent extraction, and the new Union Carbide Nuclear Co. mill to be constructed at Rifle, Colo., will also employ this method. Solvent extraction circuits will be incorporated in two mills now under construction -the Texas Zinc Minerals Co. mill at Mexican Hat, Utah, and the Gunnison Mining Co. mill at Gunnison, Colo. In Canada the expansion of the Eldorado mill at Port Radium includes installation of a solvent extraction circuit. Solvent Extraction Process: In simplest terms, the organic solvent is mixed with leach liquor and then the organic and aqueous phases are allowed to separate. By this contact the solvent selectively extracts uranium from the liquor, leaving a raffinate, or barren leach liquor, which may be discarded. The pregnant solvent is stripped of its uranium by con- tact with a stripping solution, such as aqueous sodium carbonate, which has a greater affinity for uranium than the solvent does. The barren solvent from the stripping step is available for further leach liquor extraction, and the pregnant stripping solution, which usually contains 30 to 60 g U3O8 per liter, is ready for precipitation of a final product, or uranium concentrate.

Jan 9, 1957

By R. A. Pasternak, B. Evans

In an ultrahigh-vacuum study of the sorption of nitrogen by niobium* resistivity data for this metal have been obtained as function of temperature and of low nitrogen concentrations. The ultrahigh-vacuum system in which base pressures of about 5 x l0-10

Jan 1, 1965

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. NO doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data. Dr. Cook's analysis of rock behavior based on energy considerations represents a significant new approach to mining rock mechanics problems. Although the foundations of this analysis are somewhat broader and more general than elastic analysis, the development and applications are grounded almost entirely in the theory of elasticity. It has long been known1,2 that all rocks, even granites and dense limestones, exhibit nonlinear time-dependent strain properties to a greater or lesser degree. Creep strain (that is, deformation under constant stress) in salt, potash, and trona can be several orders of magnitude greater than instantaneous elastic strain. Design of underground workings in these materials must incorporate provisions for these strains and must therefore go considerably beyond elastic analysis. Some of the principles of underground design in highly plastic materials will be discussed in this paper. Since all rocks, especially when highly fractured, exhibit a certain amount of creep-type strain, these concepts should be at least recognized in any rock mechanics problem. The discussion will be illustrated largely, but not entirely, by examples drawn from

Jan 1, 1967

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

By R. W. Borio, T. S. Spicer

Inflammability and crossing point apparatus were used to study the influence of increasing amounts oi such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition. The ignition phase of the combustion of solid fuels has been under study periodically since 1900. With the advent of pulverized coal firing some 60 years ago, a technique now dominating the coal utilization field, the ignitibility characteristics have become increasingly important. Much of the early work was directed toward the prevention of coal dust explosions and improved mine safety rather than combustion. Many factors affecting ignitibility have been studied and numerous methods devised in an effort to measure the ignition temperature and these have been reviewed by other authors. A recent survey was made by Finney and Spicerl in 1959, so a discussion of previous work will be omitted. Despite these efforts, the initial stage of combustion, termed ignitibility, is still a little understood phenomenon. In fact, no ASTM method has been adopted for the calibration of this illusive property. However, a D-5 Subcommittee XVI on Ignitibility of Coal and Coke of ASTM (now inactive) defined ignitibility:' "The ignitibility of a fuel is that char-

Jan 1, 1963

By Cornelius F. Kelley

SEVENTY-FIVE years ago, in Wilkes-Barre, Pennsylvania, 22 men of vision banded together to initiate this great organization. Ideals and emotions mingled and united in the declaration of a twofold purpose: first, the more economic production of minerals and metals, and second, the promotion of greater safety and welfare for each man so employed-tacit recognition of the inseparability of humanitarian and utilitarian concepts of world progress. The members and honorary members then, as now, were mining engineers and associates from allied walks of life. Under the able guidance of David Thomas, our first president and outstanding ironmaster of the time, there were elected 46 members and associates, and the foundations of the Institute were laid. Conceived in a turbulent postwar era, the problems then faced had some similarity to those we face in this time of war-bashed uncertainty. With a Civil War behind them and once again dedicated to a spirit of national endeavor, they surveyed the landscape, then surged ahead toward a beckoning industrial horizon. That effort has never been relaxed. Poised upon the threshold of a new century, rancher, banker, engineer and businessman paused to contemplate and evaluate his natural endowments. Surrounded by immeasurable God-given wealth, necessity inspired

Jan 1, 1947

By D. F. Malott

The Michigan Dept. of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large-volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a rehtive aid in assessing rock strength is reported. These past several years have been a period of unprecendented construction and commercial expansion. Vast private manufacturing complexes and government road, power, and office projects are being built or are in planning stages. Nearly everywhere, municipalities are expanding outward and upward. Many towns are developing into cities and many cities are displaying new skylines, and the building boom shows little sign of slowing down.

Jan 1, 1970

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

By Rossiter TV. RAYMOND, Charles H. Snow, THEODORE DWIGHT

SECRETARY'S NOTE.-The complete list of all officers of the Institute will be found on p. iv. of this number of the Bulletin. The following explanation may recall to old members, and convey to new ones, the relations of the two governing bodies, as determined by the, Certificate of Incorporation of the Institute, and the Constitution and By-Laws adopted in accordance therewith. The body legally responsible for the business management is the Board of nine Directors (three elected annually to serve three years), which elects its own officers. This body, for reasons of practical convenience, is composed of well-known members, residing in New York City, and able to attend, without serious inconvenience or expense, the necessary meetings of the Board. The officers of this Board are legally the officers of the Institute. But, apart from business manage-ment, the Board exercises no control over the election of members, or the professional and technical work of the Institute, except that its vote is required to elect honorary members, upon the recommendation of the Council. The Council is a. body, constituted in all respects (except that it has no Treasurer) like the Council existing before the incorporation of the Institute, in January, 1905, and charged with all duties and powers, except those which the Board of Directors must legally perform. It elects members, appoints the times and places of professional meetings, and controls the publication and distribution of papers and volumes, etc. Its members (President, Vice-Presidents and Councilors) are elected by the members of the Institute, voting in person or by proxy, and after publication of the nominations received ; and it is intended to repre¬sent, as far as practicable, both the professional and the geographical distribution of the membership. Consequently, whatever professional honor attaches to official position belongs to membership in the Council, rather than in the legal Board of Directors. This remark implies no disparagement of the members of the latter body, every one of whom has served, or is now serving, as a member of the Council. But it is only fair to explain that their election and continued re-election as Directors is simply a matter of legal convenience.

Mar 1, 1906