Search Documents

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

By A. R. Troiano, W. J. Barnett

The existence of a grain size stabilization effect on martensitic type reactions as shown by Scheill in an iron-29 pct nickel alloy and by Troiano and Tokich2 in cobalt prompted a review of other martensitic reactions to determine if this stabilization effect is characteristic of all martensite type reactions. Preliminary work has shown this effect to be present both in the gamma —+ epsilon transformation in an iron-20 pct manganese alloy and the martensite transformation of SAE 4140 and 3 pct Cr-O.40 pct steels. No appreciable effect was found in an SAE 2340 steel. The M, temperature for the gamma —+ epsilon transformation was lowered from 380°F to about room temperature by varying the annealing treatment following cold work as shown in Table I. The effect of austenitic grain size on the M, of three steels is shown in Table 2. M, was deter- mined by the conventional quench-temper method of Greninger and Troiano. In a single crystal the change in external shape concomitant with the homogeneous shear mechanism of the martensite transformation can take place unhindered. In a polycrystalline specimen a restraint of these changes must occur at the grain boundaries. Therefore, the smaller the grain size the greater the shear strain energy necessary for the formation of a martensite crystal. The degree of lowering of M, due to the reduction of grain size is much greater when the change in crystal structure involves only a small energy change, such as face-centered cubic —+ close packed hexagonal (that is, CO and Fe-20 pct manganese alloy). The maximum lowering of M, observed in the steels investigated was 50°F with a change in the ASTM austenitic grain size of 1-2 to 8-9. In comparison, the crystal structure change face-centered cubic —+ body-centered tetragonal involves a considerable energy change. There is little doubt that with much finer grain sizes the increased grain boundary restraint would greatly enhance this stabilization effect. The implications of this phenomenon are multifold. Undoubtedly. under certain conditions it offers a method of stabilizing high temperature phases for room temperature

Jan 1, 1949

By Dorsey Lyon

INTRODUCTION THE electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists, as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in the production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly y the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name" refining". is applied to the present finishing process, because in the operation oxygen and other impurities are removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral; the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities.

Jan 8, 1914

By R. V. Norris

The anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, iii the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of' the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jan 1, 1912

By Ernest Lilley

WHILE American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, Amer-ican literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year .the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both com-mercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, ;end other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset. in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline.

Jan 1, 1932

By Henry M. Howe

What should be the chief aim of a metallurgical laboratory ? Before answering this, let us ask, What should be the chief aim of metallurgical instruction ? Taking a definite case, that of the iron blast-furnace, should we chiefly teach the methods of bosh- and tuyere-cooling, of storing and assembling materials, of removing the iron and cinder, of firing boilers and cleaning stoves ? Or should we aim chiefly to lay clear and bare the nature of the reactions which occur in the blast-furnace, the reason why changes in the rate of driving, in the blast-temperature, in the composition of the cinder, cause their known effects ? Shall we chiefly describe or explain ? Shall we teach chiefly the looks or the reasons ? Put thus, the question admits but one answer. Hours of labored description at a technical school give a less true and clear view of actual metallurgical operations than a brief visit to metallurgical works. If in my teaching 1 take the far more laborious course and lay so very great stress on explanation and so little on description that I seem to err on that laborious side and not to give description enough, the student will quickly make up for my lack of description in his first weeks in the works; he will there learn quickly and easily what I could have described only obscurely and with labor. Details of practice are learned easily and retentively in the works, but with difficulty and slowly at school. With the principles, and especially the chemical principles of metallurgy, the reverse is true. The works have little facility for teaching them; the school has every facility. The place then for explaining, for teaching principles, is the school. But,

Jan 1, 1900

By T. B. Counselman

THE importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- [ ] ments from the Lake Superior district. Canadian ores are omitted. [ ] Only in Minnesota is concentrating, other than crushing and screening, practiced at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. CLASSES OF ORE The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive experimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-grade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1941

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct ThO2,*, and the ilmenite 56 1/2 pct TiO2, whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be avail- able in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources. 1 Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations.

Jan 6, 1950

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By Julian M. Avery

IN its dual role of pig-lion smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose During the past 10 years or more, improvements in blast-furnace technique and economy have, n fact, been directed primarily to increasing efficiency n the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace The net over-all result is a decrease n the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently amore than offset n value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements The purpose of the present paper is to suggest that, while progress has been made n this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure, i e , the "top pressure" under which the furnace is operated It is indicated that pressure operation may also be expected to result n concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By R. L. Moment

The anisotropic elastic behavior of rolled beryllium sheet has been measured, using a pulse echo technique, and compared with X-ray diffraction data. Calculated elastic stiffness constants compared favorably with published values for beryllium single crystals which were attributed to the strong (0002) rolling plane texture. Variations of Young's modulus in the yolling plane could be associated with the velative distribution of (0002) planes out of their ideal position in the rollitzg pkule. WHEN a metal is subjected to cold working such as drawing, forming, or rolling, a crystallographic texture develops which can significantly alter its physical properties. One method for detecting this texture is X-ray diffraction, but Alers and Liu' have recently pointed out how the prediction of anisotropic physical properties from pole figures alone is not always accurate due to differences in interpretation. Variations in Young's modulus with orientation or, more completely, the values of the effective elastic constants of the worked metal, also serve to indicate the presence of a texture. In fact, as Alers and Liu' pointed out, calculated variations in Young's modulus for assumed orientations, when compared with experimental data, can be used to eliminate some of the uncertainty in interpretation of X-ray pole figures. Thus, elasticity measurements can serve not only to clarify any unusual elastic behavior of worked metal, but also to detect and in part determine the nature of its texture. X-ray determination of the texture of rolled beryllium has been reported by Smigelskas and Barrett,2 who found a strong texture of (0002) in the rolling plane with (1070) planes normal to the rolling direction. In the case of metal rolled at room temperature, they reported that [1010] directions also appeared at positions 60 and 120 deg from the rolling direction in the rolling plane, while in more recent work Keeler3 found these directions were also tilted towards the rolling plane. The texture for beryllium rolled at 80O0C, however, only showed (1010) planes normal to the rolling direction and the spread of (0002) planes out of the rolling plane was less. In looking for elastic anisotropy one might consider unidirectional rolling of a metal as introducing an or-thorhombic symmetry through reorientation of the grains, since the three deformations, compression, extension in the rolling direction, and extension in the cross direction, are orthogonal to each other and unequal in magnitude. Thus the rolled sheet could be treated like an orthorhombic single crystal and the nine stiffness constants of the elasticity tensor used to calculate the anisotropy of Young's modulus, the shear modulus and Poisson's ratio. In this case we could write: which is symmetric about its diagonal. Borik and Alers4 have recently used this approach on rolled die steel with very good results. They found, however, that instead of displaying orthorhombic elastic symmetry their specimens could be considered tetragonal in which case Cr1 = c22, c13 = Ca, and c44 =cjj. This conclusion was made solely on the basis of the measured tensor elements, and serves to point out the advantage of this method for studying the anisotropy of rolled metals. Their calculated values for Young's modulus as a function of angle in the rolling plane also checked very well with direct measurements made on different specimens using the resonance technique. In the present study, cross-rolled beryllium was used which had been unidirectionally rolled about 11 pct for the final reduction. This imparted a slight anisotropy in the rolling plane which was detected both by X-ray techniques and elasticity measurements. For purposes of discussion in this paper, the rolling direction is that direction in which the most reduction passes were made and cross direction is the normal to the rolling direction in the rolling plane. It was also decided to consider the rolled sheet as displaying orthorhombic symmetry for the purpose of obtaining elasticity samples with the direction defined as in Table I. Any change in the final symmetry attributed to the sheet would then be made on the basis of the measured elastic stiffnesses. The final data would then be compared with that expected from the X-ray study and that reported for beryllium single crystals. EXPERIMENTAL PROCEDURE Rolling Schedule. The samples used in this study were taken from a large sheet which, because of its size, had to be unidirectionally rolled for the final reduction. The resulting texture was that of cross-rolled metal with a slight unidirectional texture superimposed. A cast beryllium ingot, 9.500 in. sq by 3.325 in. thick, was cross-rolled to 81 pct reduction followed by unidirectional rolling for an additional 11 pct to give a total reduction of 92 pct. The thickness of the final sheet ranged from 0.265 to 0.280 in. Reduction up to 67 pct was done at 980°C and the final 25 pct at 870°C. Analysis for metallic impurities showed aluminum 0.06 pct, iron 0.19 pct, and silicon 0.11 pct, giving a beryllium purity of 99.64 pct.

Jan 1, 1968

By Thos Stroup

RECENT contributions to the literature relating to the problems of coal mine management have discussed the pros, and cons of unionism among the miners as bearing upon the immediate problems of the industry, but have devoted singularly little thought to the underlying causes, and the fundamental reasons. for the remarkable growth of union sentiment among the miners, a growth paralleled only in the case of the railroad workers. It is all very well to revile their organization, its obvious stupidity and stubbornness, its multitude of economic and social crimes, but it is also well to realize that there have been deep-seated causes for all these things, causes that, while operating in all industries and amongst all workers, have in none of them found the optimum conditions for development such as exist in the coal mining industry. The rise of the United Mine Workers of America to a position of importance in the industry synchronizes roughly with the introduction of short-time operation; of course seasonal shutdowns and slow-time working have always been evident in our bituminous fields, but these evils have grown steadily worse since 1895 and the U. M. W. of A. has grown steadily stronger; yet short-time operation alone cannot account for this tremendous growth for, witness the signal failures that have always attended the attempts to organize the harvest workers, the fruit packers and other highly seasonal workers.

Jan 9, 1923

By Emile Hiertz

THE first press was installed in June, 1910, and the second in March,1911. They produce 1,000 briquettes per hour, weighing 5 kg. (11.05 1b.) each, under a pressure of about 400 kg. per square centimeter (5,689.2 lb. per square inch). The chloride of magnesium is received from the potash mines at Hanover in tank cars in approximately a 35 per cent. solution. The quantity of solution added to the flue dust varies between 2 and 3 per cent., so that the briquettes contain about 1 per cent of MgCl2. To fresh dust as much as 10 per cent. of coke breeze may be added and bri¬quettes made that still have a crushing strength of from 25 to 30 kg. (377 to 426.6 lb. per square inch) after 36 hr., and 45 kg. (639.9 lb. per square inch) after six days. After having treated 140,000 tons of the material, the reports of the blast furnaces show that the briquettes improved the action of a furnace and produced less dust than did Minette ore. As much as 35 per cent. of briquettes is added to the furnace charge without bad effects on operations. The presence of chlorine did not produce any corrosion in the furnace, downtakes or other piping. The presence of a certain amount of chlorine in the dust reduces the amount of chloride of magnesium which it is necessary to add for briquetting.

Jan 12, 1913

By Rudolph G. Wuerker

THE Krupp-Renn Process,[1] has been successfully used to treat low-grade iron ores, laterites, titaniferous sands, and other minerals, and before World War I1 25 units were built by the Krupp-Grusonwerk, Magdeburg, Germany. J. J. Howard[2] has shown theoretical advantages of the pyro-metallurgical treatment over conventional approaches; and the process was described by R. Durrer[3].

Jan 1, 1951

By John A. Shelton

One of the heaviest burdens uselessly cast by our mineral land laws upon the holder of the title conveyed by a patent from the United States is due to the provision excepting known veins from land patented as placer. In many instances the expense of defending such titles from the assaults of the owners of lode locations made upon the theory that the veins so located were known to exist at the date of the placer application for patent has exceeded many times the value of the land in question. Neither the lapse of time, however long after the issuance of the patent. nor repeated adjudications by the courts serve to quiet such titles Or to prevent them from being questioned. In the passage of laws providing for the acquisition of title to the mineral lands of the United States, Congress provided that the title to known veins should not pass from the United States by a patent based upon a placer location. As construed by the courts, the law (Sec. 2333 R.S.U.S.) provides that the applicant for a patent upon a placer claim may, if any vein of sufficient value to justify the expenditure of money in its development is known by him to exist within the boundaries thereof, include in his patent application an application for patent upon the vein as a lode claim; and failure to do so is to be deemed a conclusive declaration that the applicant makes no claim to the vein nor to an area of surface ground extending for 25 ft. (7.6 m.) on each side of its middle or center. As to such vein and such area of enclosing surface ground under the circumstances stated, the title remains in the United States notwithstanding the issuance of a patent that purports to convey the entire surface of a described area and everything beneath it, excepting only the segments of veins the apices of which lie outside of such area. Such known veins with such area of enclosing surface ground are, of course, at any time, so long as they remain unlocated, subject to location and appropriation in the same manner as other. veins upon the public domain. The history of the operation of this law in one district will serve to illustrate its effect generally throughout the mining regions of the United States. In the Butte district, the mineral that first attracted the atten-

Jan 1, 1920

By F. R. Archibald, C. F. Jackson

THE prospect of winning aluminum from clay was recorded almost a century ago at a time when the metal was no more than a curiosity.? As the industry developed, and it has probably developed faster than that of any other metal, the expanding need for raw materials was adequately met by the ample supplies of bauxite ore. As with the other metals older in industry, however, lower grade ores have gradually entered the raw-material field through improvements in ore dressing, insufficienoy of high-grade ore supplies, favorable geographic location, or national necessity for domestic supply. So with aluminum, or alumina, which has been established as the requisite intermediate, the time may have come when a satisfactory process, with favorable location and suitable raw materials, can hold a sound place both in metallurgy and economics. It is the purpose of this paper to describe the Ancor process and its proposed application in treatment of clay in a plant now under construction at Harleyville, South Carolina, by the Defense Plant Corporation. DEVELOPMENT OF THE ANCOR PROCESS The Ancor process has developed through successive stages of laboratory investigation, pilot-plant demonstration using nepheline syenite and pilot-plant demonstration using kaolin-type day from South Carolina, and is now in preparation for unit trial on an operating plant basis using the latter material. The laboratory studies were carried out over a number of years in the laboratory of the American Nepheline Corporation in Rochester, N. Y., and for the same company in the ore-dressing laboratory of Beattie Gold Mines, Que. Ltd. at Duparquet, Quebec. Both companies are associated with Ventures Ltd., Toronto, and its associated American companies. The work was originally undertaken with a view to recovery of alumina and alkalies from nepheline syenite as an adjunct to the American Nepheline Company's established business in the glass and ceramic trades, but as a process developed the possibility of application to clay and other aluminous raw materials become apparent and the laboratory studies were broadened to include these as well. Under the more pressing impetus of wartime needs and possibilities, pilot-plant operations were undertaken at the Canadian Bureau of Mines Ore Dressing Laboratories in Ottawa, and for purposes of demonstration under joint sponsorship of the Canadian Bureau of Mines, The American Nepheline Corporation, and The Aluminum Company of Canada Ltd.

Jan 1, 1944

By C. D. Gilpin, Franklin Moeller

The application of electric power for driving mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere considcration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons........... 15,680 1b. Weight of skip.......................................... 8,000 1b. Weight of cage.......................................... 1,800 1b. Maximum depth of hoisting.............................. 4,000 ft. Diameter of rope.......................................... 15/8 Total weight suspended on one rope from drum............. 42,000 1b. Normal hoisting speed.................................... 2,700 ft. per minute. Maximum hoisting speed.................................. 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft. depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding % ton, and about 10 cars are the usual load for a skip. All of the ore is dumped into underground bins, which are of diffcrent capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 1, 1916

By D. L. Ritter, N. J. Grant, B. C. Giessen

Forty-six alloys covering the complete concentration range of the Nb-Rh system were examined by metallographic and X-ray methods; solubility limits of terminal ad intermediate phases and transformation and solidus temperatures were determined. There are nine intermediate phases; two eutectic, five peritectic, two eutectoid, and three peritectnid reactions were encountered. The experimental methods and the constitution diagram are described in Part I. Part 11 deals with the crys -tallography and relation of the intermediate phases. The Nb-Rh system was selected for study for three reasons: first, it was hoped that the anticipated similarity of the Nb-Rh phase diagram to the Ta-Rh1 and Ta-Ir2 diagrams treated earlier (see also Ref. 3) and to the Nb-1r4 diagram treated simultaneously would allow a crystallographic and comparative evaluation of the intermediate phases in these related systems; second, it was likely that the previous experimental methods could be carried over without significant change; and third, it was expected that the interesting mechanical properties of the a1 phase of the Ta-Rh and Ta-Ir systems would also be encountered in similar phases of the new systems, and that these phases could be investigated more closely. The phase diagram had not been treated fully in the literature; only brief surveys of some intermediate phases were found.5-7 It was attempted to cover the details of the phase boundaries, Part I, as well as to present the crystallography of the intermediate phases, Part 11. EXPERIMENTAL METHODS Specimen Preparation and Treatment. The following high-purity starting materials were used. 1) Niobium powder, 99.8 pct pure, mesh size -60 +200, from Wah Chang Corp., Albany, Ore. The analysis furnished by the supplier showed the following major impurities: Ta, <500 ppm; Zr, <500 ppm; 0, 300 ppm; Fe, 280 ppm; Ti, <I50 ppm; W, Si, <100 ppm; C, N, 30 ppm; all other impurities, <30 ppm. 2) Rhodium powder, ground sponge, 99.9+ pct pure, mesh size -80, from J. Bishop Co., Malvern,

Jan 1, 1964

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900