Search Documents

By Rodolfo V. de la Cruz, Richard E. Goodman

Knowledge of the initial state of stress in rocks provides a key to the solution of many problems in rock mechanics. The initial state of stress is part of the basic data required for rational design of structures in rock, since its redistribution when engineering activities are conducted is a primary load on the rock portion of the engineering system. Knowledge of initial and subsequent changes in the state of stress is also relevant in the study of active faults and crustal strain. The purposes of stress measurements are not generally well served by methods which disclose only one of the stress components at a point. Recently, interest has centered on overcoring methods which though ex- pensive and difficult have the important advantage of yielding data on three or more stress components. In a previous paper, the authors introduced a new method-termed borehole deepening-based on measurement of the deformations that occur close to the bottom of a borehole when it is deepened by further drilling without overcoring.l The proposed method is at a disadvantage when compared with over- coring procedures in that the quantities to be measured are somewhat smaller and the measuring environment is more hostile. However, the borehole deepening method presents three distinct advantages in comparison with overcoring procedures: (1) Using the same borehole, both the initial and the subsequent changes in the state of stress can be obtained by borehole deepening. Stress changes with time are

Jan 1, 1970

By A. L. Field

A. W. FAHRENWALD, Socorro, 'N. M. (communication to the Secretary*).-When asked to discuss Mr. Feild's paper, I felt most highly complimented to have the privilege of commenting on such a worthy and needed piece of apparatus. In consideration of the importance of the viscosity of blast-furnace slags and the relation existing between the' melting point of a slag and its viscosity, the introduction of this apparatus should be a welcome means or assistant in the study of the physical properties of a slag. Up to the present time, it is A fact that this side of the practical working of the blast furnace has been sadly neglected by those investigating slags. It is easily seen that the fluidity of a slag is of as great importance as its melting point. It is not necessarily true that a slag having a low melting point will have a correspondingly low viscosity or be highly fluid. For example, a slag having a melting point of 1,100° C. may have to be superheated to, say,1,300° C., in order to have as high a fluidity as another slag whose melting point is, say, 1,250° C. The latter in this case would be the more economical. This point has been brought out very nicely by Mr. Feild. Before discussing this paper further, I think it will be well to outline some of the points, a discussion of which may be in order:

Jan 3, 1917

By R. L. Fleischer, R. S. Davis

BICRYSTAL specimens grown from the melt have been used extensively for investigations of the influence of grain boundaries on plastic deformation. The bicrystals are usually of predetermined orientation prepared by seeded growth from the melt in milled graphite boats. This technique has been described in detail by Chalmers.' Since the direction that the grain boundary follows during growth is affected by both thermal conditions and crystallography, a difficulty arises in maintaining the grain boundary position constant along the length of the specimen. This problem is particularly

Jan 1, 1960

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer' up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der' found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.'' APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

By J. L. Gillson

The big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits; and some have made classical Studies introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the highest peak in the range. The finer grained and lighter colored rock is called the Whiteface, after another mountain appropriately named for a cliff colored by this facies of the anorthosite.

Mar 1, 1956

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine milt",3 across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40' to 45' southeast

By W. A. Oates, J. S. Blakemore, E. O. Hall

AS part of an investigation into the effect of hydrogen on the serrated yielding of Ni-Cu alloys,' it was necessary to determine the solubility of hydrogen in the alloys of interest. With the exception of the work by Fukusima and Mitui2 who investigated the solubility of hydrogen in solid Ni-Cu alloys at 20 wt pct intervals at 1050°, 700°, and 350°C, the information in the literature is limited.3-10 Alloys were prepared from deoxidized Analar Copper and Mond Nickel pellets.' Wire samples were hydrogenated at 7.8 atm in an autoclave consisting of 5 ft of thick-walled Inconel 600 tube with a resistance furnace around the middle portion. The top end, at room temperature, was fitted with a safety valve, a calibrated pressure gage, and a sample inlet, while the bottom end, again at room temperature, was filled with water. After reaching equilibrium samples were quenched by dropping from the high-temperature region of the autoclave into water. They were then quickly transferred to liquid nitrogen where they were stored until analyzed for hydrogen using an Exhalograph.11 The results, which are shown in Fig. 1, represent the mean of two separate determinations on each sample. Because of the lower level of hydrogen at the high copper end of the series, the results here are of poor precision using this method. Fortunately, the results of Himmler9 using the Sieverts technique are available for these copper-rich alloys (>80 at. pct Cu)

Jan 1, 1969

By W. C. Winegard, C. J. Simpson

BNINGESSNER et al.1 have shown that the solidification substructure in dilute cadmium alloys persisted after repeated deformation, recrystallization, and annealing treatments. On the basis of this and similar evidence, Whelan has suggested in a recent publication' that the solidification structure might affect the mobility of grain boundaries even after primary re-crystallization. This suggestion is important, since the technique used by previous investigators3-5 to fabricate grain growth specimens consisted only of casting, deforming, and recrystallizing prior to the grain growth anneal. Usually no attempt was made to homogenize samples with prolonged annealing. Experiments. To test the Whelan hypothesis, grain growth experiments were performed with samples in which the degree of solute segregation was altered by controlling the solidification rate of the alloys. The initial experiments were performed on the Pb-Ag system. Alloys containing 0.01 at. pct Ag were produced from 99.9999 pct Pb and 99.999 pct Ag. Cylindrical samples, 40 cm long and 12 mm in diam, were solidified in graphite-coated Vycor tubes by lowering them through a vertical furnace at varying rates with the furnace power settings constant. Six-centimeter sections were discarded from each end, and the 28-cm section from the center was cut into sections 25 mm long for grain growth experiments. These samples were deformed with the aid of a drophammer to a uniform thickness of 5.7 mm. After almost instantaneous recrystallization, the samples were given a grain growth anneal for various times at 260°C in a salt bath. Experimental results are shown

Jan 1, 1970

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905

By G. J. Heuer, J. N. Dew, G. C. Clark

The effect on well behavior of partial permeability barriers, changes in producing rates and well spacings have been calculated through use of a radial, unsteady-state, two-phase-flow mathematical model. This model allows for variations in permeabilities and porosities with distance from the wellbore. The numerical methods necessary to solve the problem require use of a highspeed digital computer, in this case an IBM 704. In each instance, pressure and saturation gradients, gas-oil ratios and recoveries around a well producing by solution-gas drive have been calculated as a function of time and distance from the wellbore. Comparisons are made to show the effect of changes in producing rate and of varying permeability near the wellbore and out in the formation on the production and pressure history of the well. The effect of different well spacings on producing rate and ultimate recovery is considered. Although the mathematical description of the reservoir is simplified in comparison to an actual reservoir, the results do give some insight into the difficult problem of spacing and proration in a heterogeneous solution-gas-drive reservoir. Results show that for the cases considered spacing has little effect on ultimate recovery and that permeability barriers removed from the well decrease producing rate for a period of time but have only a small effect on ultimate production. INTRODUCTION The effect of spacing and producing rate on the production characteristics and ultimate recovery of a well producing by the solution-gas-drive mechanism have been topics of interest to the oil industry for many years and the subject of many hearings before state regulatory bodies. The problem is very complicated because of the difficulty of simulating in the laboratory a reservoir producing by the solution-gas-drive mechanism under anything like normal field conditions. This paper gives the initial results of a study aimed at determining the effect of these factors on production from reservoirs simulated by a mathematical model. Two-phase, unsteady-state equations are used to calculate pressures, saturations, and rates of oil and gas flow as a function of time and distance from the wellbore. The model is radial, and reservoir properties may be varied with distance from the wellbore. A decrease in permeability at a given distance results in a low-permeability ring concentric with the wellbore through which all the fluids from more distant portions of the reservoir must flow. The current mathematical model allows for variation of permeability, porosity and saturations as a function of distance from the well. Any desired drainage radius for the well may be selected. Drainage radii of 745 and 1,053 ft, which correspond to 40- and 80-acre spacing, were chosen for the calculations which follow. A large amount of the input data has been held constant. No investigation was made into the effect of changes in fluid properties and relative permeability characteristics on oil and gas production behavior. Fluid properties and relative permeabilities are essentially those of the White Mesa portion of the Greater Aneth area in southeastern Utah. A recently concluded hearing before the Utah Oil and Gas Conservation Commission to determine spacing for the field aroused interest in the possible effect of permeability constrictions located some distance from the well on production and recovery. This interest stimulated the present study. In this paper, no attempt has been made to simulate any field production characteristics exactly. Only the solution-gas-drive mechanism has been investigated, and production by liquid expansion has not been considered. This investigation is exploratory in nature but does give some insight into the problems of spacing and proration in a solution-gas-drive field having permeability variations. THE MATHEMATICAL MODEL The mathematical model is similar to that proposed by West, Garvin and Sheldon.' Approximately the same techniques have been used in arriving at a solution. The equations are nonlinear, partial differential equations which have been known for some time. The particular equations used for this study neglect the effects of capillary pressure and gravitational forces. The advent of modern digital computing equipment has made their solution practical. Basically, the method solves for pressure, saturations, and oil and gas flow rates as a function of distance and time. In our model, distance to the

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,' 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By C. R. Criss, R. J. McCormick

ThiS paper .summarizes the development and perform. ance of the Coldwater Oil field, Isabella County, Mich. Production is obtained at a depth of 3750 ft from a dolomite reservoir, which is probably both Rogers City and Dundee. There appears to be no persistent barrier to vertical fluid movement between the Rogers City and Dundee, and both formations are believed to have a common original oil-water contact. No we1ls are open to production at the level of the Dundee. The discovery of the field in 1944 was followed by the drilling of 81 producing wells and nine dry holes. By the end of 1952, the field had produced 12,763,000 bbl of oil, at which time 69 active wells were producing 3600 B/D oil and 21,000 B/D water. The reservoir has an effective natural water drive, and bottom-hole pressure has declined 75 psi from an original pressure of 1453 psi. Oil is undersaturated at reservoir conditions with a solution GOR of 512 cu ft/bbl and a saturation pressure of 1190 psi. INTRODUCTION Although the Coldwater Field is now in its ninth year of production, it ranks seventh in cumulative recovery, and second in current daily oil production in the State. Following complete development of the field in 1946, it has consistently contributed approximately 11 per cent of Michigan's daily production. Coldwater appears to have a greater pay thickness than most fields producing from the Rogers City forma- tion in the west central part of the Michigan basin. Except as influenced by the extent of closure and the thickness of the oil column, reservoir performance is believed to be representative of Rogers City fields in this part of the basin. For this reason, it is felt that the following presentation of factual data for the field will be of general interest. HISTORY AND DEVELOPMENT Discovery of the Coldwater field during Aug., 1944, followed favorable subsurface geological correlations and core tests drilled to a shallow stratigraphic marker horizon. The field is located in the west central part of the Michigan Basin in Coldwater Township (T16N-R6W), Isabella County. It is 60 miles west-northwest of Bay City, and near the geographic center of the southern peninsula of Michigan. The discovery well flowed 200 bbl of oil the first 24 hours from the Rogers City dolomite at a depth of approximately 3750 ft. Field production is principally from the Rogers City with a minor amount assumed to come from the underlying Dundee dolomite, although none of the wells are open to production at the level of the Dundee. Both the Rogers City and Dundee formations belong to the Devonian system (See Geologic Column-Fig. I.) In addition to Rogers City-Dundee oil production, sweet gas is produced from the Michigan Stray sand of the Mississippian system at a depth of 1400 ft. The gas reservoir has approximately the same areal extent as the underlying oil reservoir. Although gas production is an important feature of the Coldwater field, this report is concerned only with the oil reservoir. The productive area is approximately 3200 acres. The pool is developed on a 40 acre spacing pattern with wells drilled in the center of the north half of 40 acre tracts, except for a few off-pattern wells drilled along

Jan 1, 1955

By F. H. Buttner, E. R. Funk, H. Udin

Gold wires, 5 mil in diam, are found to creep viscously up to approximately 5.5x106 dynes per sq cm around 1300°K. Beyond this point, an additional slip mechanism appears. The average coefficient in the viscous range at these temperatures is 18.9 ± 7x10 12 poises. This observation and other visual observations made during the experiments agree with Herring's predictions. EARLY creep studies by Chalmers on single crystals of tin produced some of the first experimental evidence to suggest that metals deform viscously under very light stresses. That is to say, over a small initial stress range up to 150 g per sq mm, the single crystals of tin elongated at a rate proportional to the stress. The proportionality constant between strain rate and stress is by definition the coefficient of viscosity. Chalmers named this range of proportionality the microcreep range. One of the first theoretical attempts to explain the microcreep phenomenon was given by Kauzman,' who applied Eyring'sQ eneral statistical mechanical theory of shear rates to creep data then available. From the rate theory, he deduced the general hyperbolic sine law for shear rate on the assumption that the distortion of the reaction path due to stress is negligible and that the system is an infinite continuum. In order to fit the available data to the equation, it was necessary to assume that creep occurs by shear of rather large blocks of material, rather than by an atomistic shear process as in diffusion. The size of the shear units was shown to increase with increasing temperatures and lower stress, or lower strain rates. In applying the hyperbolic sine law equation to the microcreep data of tin, it was shown by Kauzman that the unit shear blocks became quite small, which suggested to him that microcreep might be a self-diffusion process. Making this an assumption, Kauz- man reworked the rate theory and arrived at an equation where the shear rate is proportional to the stress. In the form of viscosity coefficient, the equation is: o- _ \LkT V = 2qAlA where u is the stress; S, the shear rate; X, the distance in shear direction moved by flow units relative to one another in the unit process; L, the distance between layers of units of flow; T, the absolute temperature; k, Boltzmann's constant; qAL, a constant proportional to the size of flow units; and kT A, the diffusion coefficient = ------kTe-Q/RT = K X2 h Kauzman applied the expression to molten lead with a fair degree of success, the calculated viscosity being low by a factor of four. For solid lead the result is 5000 times too high. Taking q = 1, and X = dA = L = 21 = nearest neighbor distance, Udin, Shaler and Wulff8 found the equation low by a factor of lo7 for solid copper. On the basis of the discrepancy in lead, Kauzman indicated that microcreep is probably not a simple diffusion process of molecular shear units, but one involving preferential diffusion paths, or even that diffusion in solids does not involve shear at all. Cottrell and Jaswon4 treat the microcreep phenomenon on the basis of slow moving dislocations and apply it to Chalmers' data on tin with fair success. Nabarro Suggested a microcreep model in which mass movement in the direction of pull is effected by the diffusion of holes. The tension on the crystal effectively creates a greater hole concentration at regions near the crystal surfaces perpendicular to

Jan 1, 1953

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By R. W. Gould, B. G. LeFevre, A. G. Guy

The resistivity anomaly known as the K state was studied in Ni-Mo alloys containing 10.5 and 14.0 at. pct Mo. Both these alloys exhibit a large K effect which depends on the mechanical and thermal treatment. On the basis of X-ray diffuse scattering studies which were correlated with resistivity measurements, it appears that the K state in dilute Ni-Mo alloys can be associated with changes in the degree of short-range order within the a phase. An interesting phenomenon that has received much attention in recent years is the K state. The K state is marked by anomalous changes in some of the physical properties of certain alloys without the occurrence of observable microscopic structural changes. One of the early pieces of work in this area was by Thomas' who studied alloys of Ni-Cr, Ni-Cu, Ni-Cu-Zn, Fe-A1, Fe-Si, and Ni-A1. Upon annealing specimens which had been previously cold-worked or quenched from an elevated temperature he found an anomalous increase in resistivity over a certain temperature range. He also found that specimens which had been appropriately annealed to develop the K state showed a decrease in resistivity upon subsequent cold working. These effects are opposite to those found in normal alloys. Although the resistivity anomaly has been rather arbitrarily taken as the "definition" of the K state, there are several other interesting effects which accompany the resistivity increase. In Ni-Cr alloys,2, 3 for example, it was found that the hardness increases with increasing resistivity. It was also found that specimens which have been treated to develop the K state can be cold-worked for as much as an 80 pct reduction of area without an increase in the hardness. In Fe-A1 and Fe-Si alloys4 the K state is accompanied by an increase in flow stress and by a lattice contraction. In Ni-A1 alloys,5 specimens which have been treated to develop the K state also show an increase in elastic modulus. In Ag-Pd alloys6 the increased resistivity observed on annealing a cold-worked specimen is accompanied by an increase in the thermoelectric power and an increase in the Hall coefficient. The explanations of the K state phenomena are varied and depend upon the particular alloy in question. Several theories have been advanced to explain the increased conductivity with cold work on the basis of changes in the electronic configuration of the alloy as a result of local lattice distortions.7"9 Most investigators, however, believe that some type of local order in the solid solution, either short-range order (SRO) or clustering, is responsible for this effect. Theories concerning the relationship between ordering and the K state have for the most part been speculative, since there is little direct X-ray evidence that can be correlated with the above property changes. Much of the previous work on the K state was done in the Ni-Cr system where the small difference in the X-ray atomic scattering factors of the components nickel and chromium makes it very difficult to use X-ray diffuse-scattering measurements to determine the role of local order. In the Ni-A1 system, however, Starke et al.10 succeeded in detecting a connection between local order and the K state. It was found that a small but measurable K effect correlated with increasing SRO in the nickel-rich a phase. The manner in which local order might increase the resistivity of K state alloys is not completely clear. Since most of the known K state alloys contain at least one transition element, significance has frequently been attached to the presence of an unfilled d shell. It has been suggested that during the formation of the K state the number of conduction electrons decreases as a result of the transfer of s electrons to the d shell where they are more tightly bound.1'11'12 Koster and Rocholl13 have proposed that SRO can cause an increase in resistivity for alloy systems in which the number and mobility of charge carriers are reduced when the percent solute is increased. According to this hypothesis, the local environment of a given solvent atom changes in the same manner with increasing percent solute as it does with an increasing degree of SRO; hence the change in physical properties should tend in the same direction. In this hypothesis, SRO is considered only in a statistical sense, and the increased resistivity of the K state is attributed to a change in the mean distribution of electrons and holes in the s and d states as a result of SRO. From the work of Chen and Nicholson on Ag-Pd alloys,6 it appears that the K state can occur in systems for which the d shell is completely filled. These investigators explained the increased resistivity by picturing the SRO as small domains of some form of long-range order (LRO). According to ~ibson,'~ the number of effective electrons can be reduced by the creation of a new Brillouin zone boundary near the Fermi surface of an alloy as a result of the changing crystallographic symmetry that accompanies the formation of a superlattice. This idea may be expressed in terms of the superzone concept.15 In the present work the role of local order in the formation of the K state in Ni-Mo alloys was investigated. The principal tools used in this study were X-ray diffuse scattering and electrical resistivity measurements; however, these data were supplemented by electron microscopic and field-ion microscopic data. The purpose of the work was to determine whether or not the K state in Ni-Mo alloys can indeed be attributed to the formation of SRO as has been proposed by previous investigators.

Jan 1, 1969

EUGENE McAULIFFE, * St. Louis, Mo.-The method employed by the Engineer's Committee in arriving at a proper selling price for coal and coke represents hard painstaking effort based on a thoroughly scientific foundation; and the United States Fuel Administration can well point with pride to the work of this committee. The results so obtained placed

Jan 12, 1918