Search Documents

E. L. BLOSSOM, New. York, N. Y.-That this paper deals with a real problem is illustrated by a statement made to the speaker a few months ago by the manager of a silver-lead property: "Our ore contains 60 per cent. silica on which the smelters are penalizing us heavily, and they are not able to take all our stuff even then. We have simply got to find some method other than smelting for getting the silver and lead out of our ores. We have had experts down here and have investigated flotation, leaching and volatilization, of which processes the latter is by far the most promising. We are continuing investigation." I was somewhat concerned in certain chloride volatilization experiments which we carried on in Denver in 1903, working on a carload of ore from Butte. Now being connected with the Cottrell process, by which method the fumes will undoubtedly he recovered if they solve the volatilization problem, I have looked into the matter again, and believe it can be developed into a commercial process. On a laboratory scale, working With silver-lead ores, experimenters have obtained a volatilization of over 90 per cent. of the total values in 30 to 60 min, on quantities of 1 to 5 lb., using a roasting dish and a muffle. That looks very good, and would be entirely commercial. On attempting to duplicate these results in a reverberatory furnace, they found that it is more likely to take 8 hr. firing to yield 75 per cent. extraction, which is not commercial at all, as it requires too much time, labor, and fuel, and the whole process is too slow. Of course it can be done, because we have done it in the laboratory.

Jan 1, 1918

By Henry M. Howe

Henry M. Howe, Bedford Hills, N. Y. (communication to the Secretary.)*—Mr. Johnson's explanation, that the rounding of the graphite masses in oxygen-bearing cast iron is due to their being in part reprecipitated after re-solution in forming carbonic oxide temporarily with.that oxygen, is certainly most attractive and suggestive. It remains to be shown whether this rounding occurs also when the solidification is too rapid to permit this process to go on. J. E. Johnson might easily test this by casting a single ladleful of his oxygenated iron in masses of varying size. If this present hypothesis is true, then the rounding ought to increase progressively with the size of the casting, and with the distance from the outside, that is to say with the time available for re-solution and reprecipitation. I question whether a like benefit is to be expected even on this hypothesis, from the oxygenation of steel. The spheroidizing of graphite does good because graphite itself is so weak. But the constituent which can be spheroidized in steel is its cementite, which is a source of strength. Lamellar pearlite, in which this cementite in effect forms long den-drites, is far stronger than divorced pearlite, in which these dendrites have been broken up into spheroids. Even the surfaces of contact between ferrite and cementite are probably sources of strength because of the amorphous iron which probably fills them.

Jan 1, 1917

IN the footnote on the first page of Prof. Stoek's paper, as printed in vol. xxviii. of the Transactions, I alluded to him, under an erroneous impression, for which he was in no way responsible, as " the present Director of the Scranton Schools." This incorrect statement placed him in a false position, as possibly having authorized the use of a title to which he had no claim. In fact, Prof. Stoek has never had any official connec-

Jan 1, 1900

By J. L. Walter

Extra-low carbon iron sheet, when deformed and annealed, undergoes exaggerated or abnormal grain growth in the critically deformed regions of the sheet. This exaggerated pmth occurs, for low strains (3 to 6 pct), only in sheet which has a fine dispersion of precipitates in the subsurface region of the sheet and fewer and coarser precipitates in the sheet interior. These particles have been identified as manganese sulfides. Wing the anneal, grains near the surface are gvowth-inhibited by the fine particles but the grains in the interior are free to grow normally. With the additional driving force provided by the strain energy, the interior grains first grow into the small subsurface pains. Eventually, these growing grains grow completely through the sheet. Calculations of limiting grain sizes at various values of strain indicate that a volume fraction of precipitates in excess of 10-' would be required to eliminate exaggerated growth in material strained to 10 pct. OPEN-COIL annealing has made decarburization of sheet steel both efficient and economically practical. Use of such material for porcelain-enameling stock is one of many possible applications of low-carbon iron since carbon in steel is deleterious to porcelain-enameling properties.' However, the extra-low carbon iron presently available presents another problem, that of exaggerated grain growth in regions where the sheet has been deformed as by bending or stretching. In exaggerated grain growth a few grains start to absorb their neighbors and these may become very much larger than the average grains of the sheet. Other names for exaggerated grain growth are coarsening, critical grain growth, secondary recrystallization, abnormal grain growth, or discontinuous grain growth. While this grain growth does not affect the enameling qualities of the low-carbon iron sheet, their presence results in a marked reduction of tensile-yield strength in the region of the sheet containing the large grains. The loss of tensile yield strength may render the material unsuitable for many applications . This report describes the results of a study undertaken to determine the cause of the exaggerated grab growth in extra-1ow carbon iron and, if possi- ble, to prescribe practical procedures for its prevention. GENERAL THEORY The driving force for exaggerated grain growth is the grain boundary free energy. This driving force is proportional to (l/rl + l/r2) where rl and r2 are the mutually perpendicular radii of curvature of the boundary between the growing grain and the grain being consumed. Thus, the greater the difference in size between the growing grain and the matrix grains, the higher the driving force for grain growth. If, however, the matrix grains are free to grow simultaneously, the driving force for exaggerated growth will be diminished. Stability toward growth of the matrix grains may be caused by a) a strong single orientation texture (texture inhibition),' b) a dispersed second phase,3"5 c) the thickness effect,' or d) intergranular segregation.7"9 As exaggerated growth occurs when growth of the matrix grains has been slowed by the stabilizing processes mentioned above, there must be an additional factor acting to promote growth of a few of the grains to the point where they are enough larger than the matrix grains that boundary energy driving forces are sufficient to cause continued growth. For instance, at the annealing temperature, growth-inhibiting inclusions may slowly dissolve and coalesce. Eventually, a grain boundary becomes unlocked and migration occurs at the expense of neighboring grains. Or, an additional driving force may be supplied to some of the grains if the material is strained. Then, since some grains will be strained less than others, the difference in strain energy between adjacent grains may be sufficient to overcome boundary locking and allow growth of the grains with lower strain energies. In the present study, therefore, such factors as the presence or absence of dispersed phases, the nature of the exaggerated growth, and the effect of strain have been considered. EXPERIMENTAL PROCEDURE I) Material and Processing. Three types of low-carbon iron were used in this study; types A and B were commercial grades, each from a different supplier.* The precise details of the processing of

Jan 1, 1963

By D. I. Cameron

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at 1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystal- line thoria.

Jan 1, 1962

By H. R. Thresh, A. F. Crawley, D. W. G. White

The densities of liquid tin, lead, and Sn-Pb alloys have been measured over a range of temperature above the liquidus. In all cases, data can be adequately represented by an equation of the type p = a + bT. For pure tin, the values of a and b are, respectively, 7.139 and 7.125 x 10-4, and for pure lead, 11.060 and 12.220 x 10-4. At constant temperature, molar volumes in the Sn-Pb system vary linearly with composition. DURING the course of a long-term program at the Department of Energy, Mines and Resources, Ottawa, Canada, the densities of liquid tin, lead, and Pb-Sn alloys were studied. The work reported herein draws on two sets of results independently achieved by Thresh, on the one hand, and by Crawley and White, on the other. EXPERIMENT The method and apparatus were originated by Thresh and have been described in detail in Mines Branch reports.172 In operation, the 14 cu cm graphite pycnometer is put in the furnace as shown in Fig. 1 after a machined charge has been placed inside the pycnometer and the lid screwed down. The dimensions of the charge are such that, upon melting, a small excess of liquid metal is discharged through the capillary hole to displace the weighted float above. When the pycnometer has been equilibrated at the experimental temperature, the

Jan 1, 1969

By Persifor Frazer

I DESIRE to say that, owing to the number of papers which have been more or less crowded at this session of the Institute, and the fact that, as one of the Local Committee, I have the distinguished honor to feel somewhat like one of the hosts, I should not tax the patience of members at this late hour, but would have my paper read by title were it in any way possible to do this. But the task I have set myself this evening is to present to the eyes of the members of the Institute certain objects which have occupied more or less of my time during the last eighteen months or two years. The objects I allude to are some of the igneous rocks of this country, which, until quite recently, have been less understood than any others. It will be well known to some of the members that some of the cooled lavas of a previous age of our planet, when not directly coarsely crystalline and granular, were considered and spoken of as " natural glasses," or perfectly uncrystalline, vitreous, or hyaline masses of matter. Among the first results of the use of the microscope was the dispersion of this fallacy. Sir David Brewster, Mr. H. C. Sorby, and William Nichol (the discoverer of the celebrated calcite prism, which bears his name), had, with greater or less success, examined sections of various rocks and minerals, both by transmitted and reflected light, and also in the form of powder. But, until the genius of Vogelsang undertook the subject, these investigations had no permanent value, nor did they constitute an independent line of mineralogical and geological research. Since the close of his labors, by Vogelsang's premature and much-lamented death, the subject has been made one of renewed interest by his brother-in-law, Ferdinand Zirkel, as well as by Rosenbusch, Tschermak, and many others abroad, and at home by the commencement of a systematic study of the traps of Connecticut by Messrs. E. D. Dana and G. W. Hawes, of New Haven, and by the splendid set of described sections of the traps of the West which have been furnished by Zirkel to illustrate Clarence King's report. I had the honor of presenting a large number of thin sections of our traps at the Washington meeting, for the inspection of the members, with the aid of a table microscope belonging to the Smithsonian Institution. Here I propose to project these sections upon the

By Fred C. Bond, Fred T. Agthe

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different texture and composition exhibit great differences in coating potentialities. Various materials were tested in thg laboratory to show the variation in coatine qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feldspathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been

Jan 1, 1940

By Laurence Delisle

The aim of this paper is the description of a technique to be applied to the study of sections of metal powder particles, less than 20 microns in diam. with the electron microscope, by the replica method, using for replica a material such as formvar or parlodion. This work originated with the study of particles of tungsten powders. Such particles were too small to be examined in sufficient detail with the light microscope. On the other hand, examination with the electron microscope of the powders dispersed in the supporting film was not found satisfactory because: 1. It did not permit differentiating between single particles and aggregates. 2. It did not show the true outlines of the particles but only the projection of a whole surface. 3. No details appeared. For that reason it was attempted to make replicas of sections of the particles imbedded in a mounting material suitable for polishing and etching. The method proved satisfactory for the examination of tungsten powder and was then extended to car-bonyl nickel and carbonyl iron powders. Procedure Several mounting materials commonly used in ordinary metallography were investigated. The problem consisted in finding a mounting material

Jan 1, 1950

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

HAVING described and taught you the method of assaying silver for gold in the preceding chapter, and therein having proceeded in the order and Drover wav followed in the working of quantities of gold and silver, I could have fled this task of describing to you the first part of parting. In truth, there is no other difference in the method of arriving at the end except in respect to certain precautions that must be taken against the dangers causing loss. In order that you may guard against these, I shall repeat the procedure completely, in addition to the second part of this art, which is the method of reducing the silver to its body.

Jan 1, 1942

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

By K. K. Rao, M. E. Nicholson

IN a recent paper on the solubility of carbon in Ni-Cu alloys,' Nicholson reported that the carbon solubility appeared to be limited by the electronic structure of the alloys and that the solubility was propor- tional to the density of states at the Fermi surface of the "3d" band. In order to determine whether or not this relationship is a general one, the study has been extended to other systems. One of these is the CO-Ni system. This system was chosen for study because 1) it is adjacent to Ni-Cu system in the periodic table, 2) the alloys of cobalt and nickel do not form stable carbides at 1000°C, and 3) the system exhibits no pronounced change (less than 1 pct) in lattice parameter from cobalt to nickel,' see Fig. 1. The alloys were prepared from -200-mesh 99.92 pct Ni furnished by the International Nickel Co. and spectroscopically pure -200-mesh cobalt sponge obtained from Johns on-Matthey and Co. The powders were weighed, mixed, and pressed using a pressure of 40,000 psi. The samples were sintered for 24 hr at 900° C in dry hydrogen and then cold rolled to a thickness of 0.010 in. (Samples containing more than 70 wt pct Co had to be annealed after cold reductions of about 20 pct to avoid cracking.) The alloys were carburized at 1000°C in an alun-durn boat containing Acheson AUC powdered graphite in an atmosphere of carbon monoxide cylinder gas which had been passed through Ascarite to remove carbon dioxide. After carburizing for either 12 or 24 hr the samples were moved to a cool zone of the furnace to cool. Cooling required about 5 min. The samples were filed to remove about 0.005 in. from the surface and then analyzed using a conventional combustion-gravimetric analytic method. The results of this investigation are shown in the lower portion of Fig. 1 and Tabulated in Table I. The nickel percentages for these alloys were determined from the weights of the powders from which the alloys were made. The solubility of carbon in pure cobalt at 1000°C (fcc) is 0.25 wt pct. This is somewhat less than the 0.33 wt pct measured by Boecker.3 From his data, it would appear Boecker's samples were supersaturated before the equilibrating treatment and that a 20-min treatment was not long enough to achieve equilibrium. Since in the present investigation the 12 and 24 treatments produced essentially equal carbon contents, our figure is presumed to represent more nearly the equilibrium value. The solubility of carbon in nickel of 0.19 wt pct agrees quite well with the value of 0.21 wt pct

Jan 1, 1963

By E. P. Abrahamson II

The effect of transitiorz element bitzary solid solution additions upon the recrystallization temperature of columbium has been investigated. The elements Mn, Fe, Co, Ni, W, Re, and 0s OWY the yecystallization tempel-aturye, while Ti, V, CY, zr, Mo, Ru, Rh, Pd, Hf, Ta, W, Ir, and Pt mise it. A correlation is kloted between the rate of chatzge of recyystallization tewaperature with atomic hercent solute and the free atom electron configuration of the solute element. The work of Abrahamson and Grant1 has indicated a correlation between the free atom ground-state electron configuration and the change in brittle-ductile transition temperature per atomic percent solute in chromium base alloys. A similar correlation was observed for the change in the recrystallization temperature of iron base alloys by Abrahamson and Blakeney and Abrahamson. It was also observed that the limit of rapid change in recrystallization temperature also Correlated with the electronic configuration of the free solute atom. A further study by Abrahamson4 established the generality of the phenomenon by yielding similar results for vanadium base dilute alloys. It has been inferred that a peri- odicity might be expected with changes in the free atom electron configuration of the solvent element. This study is the third set of transition base metal systems to be studied. It is the object of this and further studies on transitional metal systems to detect any systematic variations in the observed correlation which might contribute to the understanding of the electron interactions which are evidently exhibiting themselves. PROCEDURE All alloys were made using 99.9 pct Cb with 0.030 Ta, 0.016 0, 0.0025 H, 0.003 Mo, 0.021 Fe, 0.005 C, and 0.002 N. The solute elements were 99.9 pct pure. According to the published binary phase diagrams5 and metallographic examinations at X750, all additions were in solid solution. The alloys were arc melted and remelted 6 times in the form of cubic 400-g buttons under an argon atmosphere. They were then hot forged at 1200oC to 0.6-in. diameter, annealed for 3 hr at 1200o under argon, and furnace cooled. The specimens were then machined to 0.400 -in. diameter. Grain size was checked and found to remain essentially constant at 150 i 30 grains per sq mm. The specimens were then cold swaged to 0.187-in. diameter, yielding 46 i 1 pct cold work. All alloys were chemically analyzed for the major solute. Analyses of random samples indicated that the impurity content remained at the values of the starting material. Tungsten contamination was held to 0.007 pet.

Jan 1, 1962

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By R. E. Ogilvie, J. I. Goldstein, R. E. Hanneman

The interdiffusion coefficients for the Fe-Ni system were determined as a function of composition in both the a and y phases at 1 atm pressure. The inter diffusion coefficients were also determined in the y phase at 40 kbar pressure. The concentration gradients were measured with an electron probe, and the diffusion coefficients were calculated by the Matano analysis. At 1 atm, Ey increases with nickel content up to 65 at. pct Ni. The relationship of Dy with temperature and nickel concentration, up to 50 at. pct Ni, is given by the equation DY-l atm = exp(.0519 CN~ +1.15) MANY of the transformations that occur in the solid state are diffusion-controlled, especially those involving precipitate growth in most metallurgical systems. Multicomponent diffusion is usually expressed in terms of a chemical or an inter diffusion The activation energy Q at 1 atm decreases from pure iron to 60 to 70 at. pct Ni and decreases from pztre nickel to 60 to 70 at. pct Ni. The Kirkendall marker movement indicates that DFe is greater than DNi zcp to about 60 at. pct Ni. Above 60 at. pct Ni, however, DNi becomes peater than DFe The inter diffusion coefficients were also compared with those calculated from self-diffusion data. A comparison between calculated and measured coefficients shows only rough agreement. The effect of 40 kbar pressure is to decrease DyPl atm by an order of magnitude. The activation volumes for high-pressure diffusion are in favorable agreement with theoretical models developed for self-diffusion. coefficient which determines the rate at which material is transferred from the matrix phase to the precipitate and hence determines the growth rate of the precipitate. Since the numerical values of the diffusion coefficients differ widely as a function of the metallic system, temperature, and pressure, the diffusion coefficients must be determined for each particular environmental condition. Of long-standing interest is the growth of the classic Widmanstatten pattern in metallic (Fe-Ni) meteorites. The growth rate of the pattern is controlled by the diffusion coefficients in the Fe-Ni system. Since these coefficients are essential to calculating the growth rate of the pattern, we found it necessary to determine the diffusion coefficients

Jan 1, 1965

By E. L. Spain Jr. N. A. Rose

This study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity. crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. Introduction When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel-exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfuls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. Sources and Types of Materials The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1938

By E. L. Spain Jr. N. A. Rose

This study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity. crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. Introduction When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel-exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfuls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. Sources and Types of Materials The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1938

By D. A. Woodford

In a constant-load creep test, if the density of nlobile dislocations is assumed constant for strains exceeding that corvesponding to the minimum creep rate, it is shown that the creep rate may be approximated by the equation where E is the nominal strain, o0. is the initial stress, and a' the stress fov unit dislocation velocity. The constant C contains the mean density of mobile dislocations and n is a measure of the stress sensitivity of dislocation celocity. This equation is shoum to be applicable to published data on an alloy steel and on nickel. The degree of plastic instability and hence the creep ductility is dependent on the calue of n for these materials. When instability becomes gross and local macroscopic necking occurs, the assumptions are no longer valid. On the basis of this equation, and the strain-time relation derived from it, a method of predicting the creep behavior at different stresses is suggested. MOst analyses of creep data have been concerned with time-dependent transient creep or time-independ- ent secondary creep in constant-stress tests. The far more widely used constant-load test has been neglected in terms of a mechanistic approach. In general, since the strains involved are usually small, the same laws for transient creep may be applied to both types of tests. However, there is no steady-state creep in a constant-load test since the stress increases continuously. Any apparent steady state observed on a strain-time plot is either fortuitous or illusory, and is generally revealed as a continuously varying creep rate on a carefully constructed strain rate vs time plot.* Transient creep may be understood in terms of a simple differential equation representing the change in mobile dislocation density with time:' where p is the density of mobile dislocations. The first term on the right is related to first-order kinetics of dislocation multiDlication and the second to second-order kinetics of exhaustion. On the basis of this equation, several authors2-4 have found good agreement with experimental transient creep curves for a number of materials. When k1p = k2p2, a steady-state creep

Jan 1, 1968

By J. H. L. Vogt

TABLE OF CONTENTS. PAGE Introduction,...........125 I. The Original Source of the Heavy Metals of Ore-DepoBits,. 126 Distribution of Elementary Substances in the Earth's Crust,. . 128 11. The Relation between Eruptive Processes and the Formation of Ore-Deposits, Especially Buch AS have been Produced by Eruptive After-Actions,........ Ore-Deposits Formed by Magmatic Segregation,..... Ore-Deposits Formed by Eruptive After-Actions,..... Cassiterite-Veins and Apatite-Veins,...... Ore-Deposits of Contact-Metamorphic Origin,.... Pyritic Deposits,.......... Veins of Gold, Silver and Lead-Ore,......142 Conclusions,........... 111. The Nature of the Ore-Solutions in Vein-Fissures, and the Metasomatic Alterations along the Ore-Veins,. .. 147 The Association of Vein-Minerals,.......147 Deposition of the Vein-Minemls,........148 Alteration of the Country-Rock,........ Classification of Metasomatic Alterations,...... 149 Additional Observations,......... Kaolinization,..........150 Comparison between Cassiterite-Veins and Lead-Sulphide Veins,. 154 Comparison between Formation of Greisen, etc., and Propylitiza tion, etc.,........... Conclusions,........... IV. Differences of Depth in the Original Positions of EPIGENETIC Deposits ; and the Secondary Alterations of Deposits,. . 158 Original Differences of Depth,. .. .. .. . Gecondary Altemtions of Ore-Deposits,......, Introduction. In the latter part of November, 1900,I received through the Secretary of the Institute the papers of Messrs. Van Hise, Emmons, Lindgren and Weed, presented at the Washington meeting of February in that year, with the request (urged also by Mr. Emmons) that I would furnish for the Richmond meet-

Jan 1, 1902