Search Documents

By H. Kobbè William

ARTHUR KNAPP, Ardmore, Pa. (communication to the Secretary*).¬On p. 2275 I find a quotation from Mr. Thompson regarding the fountains of the Baku field. I have seen a large number of these gushers or fountains. In every case where unusual amounts of sand were produced the wells caved in and shut off in a few clays and were an absolute loss Very often the formation had caved so far up as to allow the water to enter the oil strata, and not only was the well lost but the ground for many acres around the well was useless for drilling purposes because the disturbed ground had allowed the gas and oil to dissipate and the water to enter. On p. 2268, Mr. Thompson is again quoted regarding the Balakhany field. If the text is consulted further, it will be found that the oil at Balakhany is heavy only in contradistinction to the Bibi Eibat, field. The gravity of the oil at Balakhany is from 28 to 32. Also, it must be noted that the illustration is taken from the conditions in the older part of the field. This field was first chilled 40 years ago, and was a worn-out field 15 years ago. The wells which produce sand are wells in which the casings are practically gone and the formations are full of water. The sand must be bailed from these wells because the clays from the upper stratum have caved into the wells and are obstructing the passage of oil. On p. 2262 is the statement that the Russian wells cannot be pumped on account of the large amounts of free sand produced. They have never tried pumping in the Baku field to any extent. Wherever tried, it has proven a great success. If we take the author's theories as correct and wish to put them into practice, it would first be necessary to consider a few figures. Let us assume that we produce oil and sand together in the proportion in which they exist in the productive strata. It is not uncommon to have wells in the California field which are not gushers, but which, by pumping, produce 1,000 bbl. per clay the first 100 clays.

Jan 3, 1917

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By John Birkinbine

The following data concerning the general dimensions and district-location of the blast-furnaces of the United States are intended to supplement a paper of similar title, which appears in volume xiv., pages 561 to 577, of the Transactions, and bring the record to the end of the calendar year 1886. The reasons for presenting the figures at so short an interval since the former paper are that the American Iron and Steel Association has lately issued a new directory of iron and steel works (edition of 1886) from which many of the plants which have been inactive are omitted and new industries added, to such an extent as to materially affect the figures presented in the first paper; and also that the improvement in business has encouraged a production of pig-iron in 1886 in excess of any previous outputs, and the results obtained in the industry at large as well as at individual plants form a better index of what the American furnaces can accomplish than those heretofore presented. The statement will not be extended beyond the production of pigiron, although it could well be made to include the manufactured iron and steel; and while the data given have been verified as far as possible up to the close of the year 1886, no attempt, except in special cases, has been made to note the changes which have taken place since that time—changes which within the next twelvemouth will affect some of the figures here presented. At the close of the year 1886 there were 579 blast-furnaces reported on the active list—an apparent decrease, as compared with my former paper, of 97 stacks; but this was not an actual decrease, since most of the furnaces dropped from the Directory were those which, owing to location, inefficient equipment, or fake of ore-supplies, etc., were considered likely to remain inactive, although a number of them will possibly be temporarily put into blast with iron advancing in price. On the other hand the new plants added

Jan 1, 1887

By C. R. Van Hise

[Concluding Contribution of Prof. Van Hise to the Discussion of his Paper, and Others on the Same General Subject, presented at the Washington Meeting, February, 1900 (see Trans., xxx., 27, 177, 323, 424, 5 S); also of the contributions of Vogt, De Launay, Beck, Lindgren, hemp, Rickard, Bain, Keyes, Collins and Adams, presented at the Richmond Meeting, February, 1901, and printed in the present volume.] IN June, 1900, shortly after my paper was published in the Transactions, I made a briefer statement* before the Western Society of Engineers covering the same `round, which, in certain respects, is somewhat of an improvement. For instance, instead of using the terms descending and ascending with reference to the waters resulting in the two concentrations, my modified statement is as follows " The first concentration of many ore-deposits is the work of a relatively deep water-circulation, while the reconcentration is the result of reactions upon an earlier concentration through the agency of a relatively shallow water-circulation. Commonly the deep water circulation is lacking in free oxygen, and contains reducing agents, and the shallow water contains free oxygen. The deep water is therefore a reducing, and the shallow water an oxidizing agent."† Of the papers upon ore-deposits which, in vol. xxx. of the Transactions, follow my own, or which were presented at the Richmond meeting, a considerable number are wholly confirmatory of the conclusions which I have presented. Among these are the Washington paper of Emmons upon the Secondary Enrichment of Ore-Deposits‡ and his discussion at Richmond of other papers,§ that of Weed upon the Enrichment of Gold and Silver Veins,[ ]the discussion of Emmons&apos;, and at Richmond of Weed&apos;s paper by Collinst and Prof. De Launay,† the paper of Lindgren on Metasomatic Processes in Fissure Veins,¶ that of-Rickard upon the Formation of Bonanzas in the Upper Portions of Gold Veins,** and the remarks of Bain upon the Mississippi Valley lead- and zinc-deposits.†† It is therefore un-

Jan 1, 1902

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

By R. T. Bayliss

Although every mill-man of even limited experience in the amalgamation of gold-ores is probably aware that copper plates will in time become coated by the accumulation of gold-amalgam, it may be that many do not know to what extent this accumulation occurs in the treatment of ores dissimilar to those with which they are familiar, and under conditions foreign to those with which they have to contend in any given locality. The writer, therefore, feels relieved from the necessity of offering an apology for dealing with such an elementary subject, believing that certain facts in reference thereto, which have recently come under his personal observation, will be interesting to many, and possibly instructive to some persons engaged in the amalgamation of gold-ores. The facts hereinafter stated were observed in the 50-stamp "combination"-mill, owned by the Montana Mining Company, Limited, of England, operating the Drum Lummon mine, situated at Marysville, Montana. The material treated in this mill consists of quartz and ores of somewhat variable character, containing gold and silver in native form, as well as in chemical union with the sulphides of iron and copper. There is also present a little lead, some arsenic and antimony, and a little zinc. The last fair minerals, however, are of irregular occurrence, and but sparingly distributed throughout the ore, and yield only a trace in the analysis of the average material in this mill. The free gold, which is in a condition of fine division, and rarely visible to the naked eye, carries silver as an alloy; and the native silver, which is only occasionally observed, is present in the richer ores in wireand in leaf-form. Of the two precious metals, the ore worked during the past three years and ten months, the period under review, contained about 1/2-ounce of gold, and from 7 to 12 ounces of silver, per ton of 2000 pounds.

Jan 1, 1897

By D. Havlena, A. S. Odeh

The use of the straight-line method of solving the material balance equation is illustrated by means of six field cases. Also, the application of statistical criteria to arrive at the most probable answer is shown. The theory underlying the straight-line method of solution and the applicability of the statistical criteria was presented in a previous paper.&apos; The field cases include saturated and undersaturated oil reservoirs with and without water drive. The aquifers discussed are: limited radial, infinite radial, very small aquifer and infinite linear. The field cases also include a gas reservoir producing under water drive. INTRODUCTION In a previous paper,&apos; the authors presented the theory underlying the solution of the material balance as an equation of a straight line. The appropriate equations for various material balance cases as well as the methods of analysis and interpretation with comments and discussion were also included. To illustrate the various theoretical cases treated previously, five field cases are analyzed in this paper by employing the straight-line method of solving the material balance equation (MBE) and one example previously published is referred to. The use of statistical criteria to arrive at the most probable answer is also shown. All the field examples presented, except Case 2, are excerpts from complete reservoir studies. To illustrate the method, only sections specifically dealing with the material balance principles are included. Additional geologic information and basic data are reported to better acquire an understanding of the cases and thus to better follow the reasoning that suggested the successful application of the straight-line method of solving the MBE. The six cases are: (1) saturated reservoir, small gas cap, limited aquifer; (2) saturated reservoir, very small gas cap, infinite aquifer; (3) undersaturated-saturated reservoir, very small aquifer; (4) highly undersaturated reservoir, no water drive; (5) high undersaturated one-well reservoir, limited aquifer; and (6) gas reservoir, infinite linear aquifer. THE D4 SAND, GUICO FIELD, VENEZUELA The D, sand, which was discovered in 1943, is presently in a depleted state. Since its discovery it has produced under water drive, gas-cap-gas expansion, and solution gas drive. In Nov., 1947, water injection was initiated to arrest further pressure decline. When discovered, the D, sand was a saturated reservoir with a gas cap /oil zone volume ratio m estimated volu-metrically at 0.0731, an average permeability of 500 md, a porosity value of 25 per cent, and an oil viscosity at reservoir conditions of 0.3 cp. The volumetrically determined stock-tank oil initially in place was 23.1 million bbl. The volumetrically weighted physical data and production data available until Nov., 1953 are reported in Table 1. In Ref. 1, the effects on the straight-line plot of various values of ro/r for a constant ?to, or of various dimen-sionless times for a constant r8/r10 were theorized and were illustrated in Fig. 3A of that reference. In this field case, the previously theoretically predicted effects are established. Thus, the MBE calculations using Eq. 3c of Ref. 1 were performed for various r6/r10 and dimension-less time values. Eq. 3c of Ref. 1 is:

Jan 1, 1965

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By J. W. Leonard

This expanded and more detailed supplement to earlier published work1 is offered as a means to demonstrate the high empirical correlation which exists between the readily measured coal bench scale test parameters of volatile matter (d & a.f.), Hard-grove grindability index (HGI), Koppers cone bulk density (BD) and pulverization level (% passing a 1/8-in. screen) to the less readily measured full scale coke stability index. Thus, Fig. 1, 2 and 3 represent the correlated test data contained in Tables I, II and III respectively. Ninety-six coals are correlated so that 97% of the resultant cokes fall within two points and 100% fall within three points of the actual tested coke stability indices. The main generalizations which can be drawn from the correlation of these coals are as follows: 1) The coke stability indices for higher bulk density coals (46.0 BD to 50.6 BD) appear to be largely influenced by differing combinations of factors for coals above and below a pivotal point of approximately 36% to 37% volatile matter. Below this pivotal volatile matter coke stability index appears to be influenced largely as a result of changes to the coal volatile matter and pulverization level. While above this pivotal volatile matter coke stability indices appear to be dependent on the coal hardness, as measured by the HGI, and to some extent upon coal volatile matter. Pulverization appears to have little influence on the coke stabilities of the harder coals (52 HGI to 58 HGI) of greater than 36% to 37% volatile matter. 2) The coke stability indices for lower bulk density coals (41 BD to 45.9 BD) appears to be largely influenced by changes to coal volatile matter and pulverization level for softer coals above approximately 58 HGI. 3) The main empirical observation to be drawn from these results is that for coals above approximately 36% to 37% volatile matter the quantities of hard and soft constituents as measured by the HGI are important when defining coal rank for correlation to the coke stability index.

Jan 1, 1965

By W. O. Philbrook, C. W. McCoy

The reduction of chromous oxide from lime silica alumina slags by carbon-saturated iron behaves as a first-order process having a rate of 0.001 grams Cr min 1 cm 2 (pct Cr ) , substantially independent of slag composition and temperature over an important range for iron smelting. The equilibrium ratio (pct Cr)/[pct Crl is below 0.04 for slags having lime-silica ratios above 0.6. MANY studies have been conducted on chromium in slag-metal systems under oxidized conditions. The Purpose of these investigations has been twofold; namely, (1) to determine those conditions which lead to greater chromium recovery in electric-furnace and open-hearth practice, and (2) to determine the nature of oxide inclusions and de-

Jan 1, 1959

By M. R. J. Wyllie, P. F. Southwick

The importance of the so-called "dirty sand" or "conductive solids" problem in electric log interpretation was first stressed in a paper presented in 1949. Since that time the problem has been generally recognized as a most serious one. Several research papers bearing on the theory of the effects of clay contaminants on reservoir rock resistivities have appeared. These papers, while contributing to the theory of the problem, have not offered any practical solution. In the present paper an experimental investigation has been made of the effects of ion-exchange materials on the electrical properties of natural and synthetic porous media. The method used to make synthetic dirty sands is entirely novel and has proved a valuable guide to a better understanding of the properties of dirty sands generally. The effects of ion-exchange materials on both the resistivity and self potential (S.P.) logs have been examined. From the data obtained it has been possible to formulate a simple, practical method whereby electrical logs of dirty sands can be qualitatively interpreted. The method is in all essentials identical to that presently in use for interpreting clean sands. New light has also been thrown on the significance of the term formation factor when it is applied to dirty sands. In 1949 a paper was presented1 which showed that the presence of so-called "conductive solids" introduced considerable complexities into the analysis of the resistivities of dirty sands, i.e., permeable formations containing clay. The reduction of the self potential (S.P.) resulting from the presence of interlaminated shale or interstitial clay in permeable formations has been discussed by Doll.2,3 Noteworthy papers which dilate further upon the effects of shale and clay on the resistivity of permeable formations are those of deWitte,4,5 Berg,6 Wyllie,7 and most recently, Winsauer and McCardell.8 The last authors have endeavored to elucidate the chemistry of the resistivity phenomena in dirty sands in terms of an adsorption hypothesis. Specifically, they attribute the electrolytic conductivity of shales and clays within a permeable formation to an ionic double-layer effect and, for this reason, regard the term "conductive solids" as a misleading one. Some consideration has been given to the effect of dirty sands on the S.P. by Wyllie7 and by McCardell, Winsauer and Williams." Published work to date has cast light only on certain theoretical aspects of the problems created by the presence of clays and shales within permeable formations. One object of this paper is to describe experiments which serve to elucidate further the theory of the dirty sand problem and particularly the significance of the term "formation factor" as applied to dirty

Jan 1, 1955

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6&apos;6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6&apos;6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By A. G. Preban, R. J. De Angelis, J. B. Cohen, P. Gordon, D. C. Brillhart

Changes in stored energy, resistivity, density, X-ray line broadening, and dislocation arrangements (from transmission electron microscopy) have been mensured on copper specimens shock-loaded at 75 to 435 kbars. The stored energy in shock-loaded copper and changes in density and resistivity are larger than those after conventional deformation. A high density of twins makes an appreciable contribution to all the measured quantities. Dislocation densities rise to values of 1011 lines per sq cm at the highest pressure. The resistivity, density, and X-ray In a study of the effects of shock loading on copper, changes in stored energy, resistivity, density, hardness, lattice parameter, line broadening, and dislocation structure have been examined after subsequent annealing of specimens shocked to various pressures. This paper presents certain aspects of the data, taken by two groups, one at the Illinois Institute of Technology, and the other at Northwestern University, and compares the changes in these properties, and what they indicate about the effects of shock deformation. measurements yield dislocation densities in substantial agreement at all pressures, after correcting for the effects due to the twins. At the higher pressures, electron microscopy yields dislocation densities that are lower by a factor of about 5 to 10. Dislocation densities from stored -energy measurements are high; this finding can be rationalized by the consideration that the deformation twin boundaries present are largely incoherent. There is no evidence for homogeneous dislocation nucleation during shock loading. Shock loading any metal or alloy, such as copper, causes a large increase in yield strength, with dimensional changes of the order of only a few percent."&apos; Other properties have not been extensively studied, but this result clearly indicates the importance of examining the substructure. Previous studies of the substructure of conventionally deformed specimens have been made using electron microscopy,3-6 X-ray diffraction,7,8 and etch pitting.9,10 The dislocation density can reach values of about 10" per sq cm; and the dislocations are arranged in cells approximately 0.15 in size. The substructure varies widely, however, from point to point in the specimen. The substructure of explosively loaded copper consists of cells of about the same dimensions6,11 but their size is more uniform.6 Profuse twinning occurs12,13 and the twins are often too small to be detected optically.6,13 The boundaries outlining these twins appear to be incoherent.14 There is now ample evidence 13-15 that twinning is a strengthening mechanism in fcc metals but this is only part of the strengthening effect in shock-loaded copper.* From the twinning systems which operate in shock-loaded single crystals,13 and from changes in texture on shock loading,17 it has been shown that both the

Jan 1, 1968

By W. O. Philbrook, K. M. Goldman, G. Derge

EQUILIBRIUM conditions for steelmaking reactions have been studied extensively over the past two decades by a .number of investigators, with gratifying results. Equilibrium data are essential to the understanding of any process, and such knowledge has the practical utility of placing a limit beyond which control measures cannot succeed. When, however, the driving rate of an industrial process is so fast that there is not time for reactions to reach equilibrium, it then becomes necessary that the factors which control the rates of reaction be known in order to establish full control of the process. The desulphurization of molten pig iron by slags within the iron blast furnace is one such process in which the actual degree of sulphur absorption by the slag does not approach the equilibrium distribution obtained for similar slag-metal systems in the laboratory.&apos; A study of the rate-controlling factors governing the desulphurization of iron by slags is becoming increasingly important as the sulphur content of raw materials increases with depletion of higher grade ores and coal. Following up an initial study on kinetics,&apos; this paper reports some results of a continuing laboratory investigation on the mechanism of sulphur transfer between molten iron saturated with carbon and slags of the CaO-SiO,-A12O3 system. Laboratory experiments cannot reproduce in detail the conditions which prevail in the hearth of a blast furnace, but they will contribute to an understanding of the smelting reactions and perhaps will explain some apparent inconsistencies in the factors controlling the equilibrium distribution of sulphur between iron and slags under reducing compared with oxidizing conditions. The mechanism of a reaction—that is, the individual steps and the sequence in which they occur to produce the overall reaction which is ordinarily observed—must be elucidated to learn which steps are the slow ones, or "bottlenecks," that fix the pace of the process as a whole. In the desulphurization reaction, for example, the overall rate might, in principle, depend upon the rate of diffusion of sulphur in the metal or in the slag, upon the speed of some homogeneous reaction taking place entirely within one of the phases, or upon some heterogeneous reaction taking place across the slag-metal interface. Even some side reaction or the back reaction might have some influence. Evidence on all of these points will be presented in this paper. The rate of diffusion of sulphur in both iron and slag is so slow that it seems necessary to assume that convection provides the mechanism of carrying

Jan 1, 1951