Search Documents

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.' 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

Edward Keller, Baltimore, Md. (communication to the Secretary*) :—The authors of this paper are to be commended for their industry and congratulated upon the many interesting results which were the fruit of their researches. While thoroughness has marked their work in general, yet on a few points in particular they have touched but lightly, for which reason, it would appear to me, they have hit wide of the mark in their respective conclusions. The work alluded to pertains chiefly to the occurrence of magnetic iron oxide (ferroseferric oxide) in copper-mattes. Because the authors find that the magnetic residue, left by the dissolved sulphides, varies largely in quantity according to the strength of nitric acid used (with potassium chlorate) in dissolving the mattes, they conclude :— "It appears, therefore, that the ferroso-ferric oxide is the result of precipitation by the oxidizing agent, rather than an original constituent of the matte." In this part of their investigation, Messrs. Gibb and Philp have ignored some well-established data,. In the first place, they have overlooked the fact that there are mattes which are strongly magnetic and others which scarcely show any magnetic property. There is nothing in their work tending to explain this variation. They Seem to have tested none of their products for magnetism. Secondly, they have overlooked the fact that magnetic iron oxide probably exists in all ore-charges in the copper-matting furnaces, and, under the given conditions, that this oxide is very difficult to reduce and to combine with silica to form slag. Thirdly, they pay no attention to the varying specific gravity of the several grades of copper-matte, which may exceed, equal, or fall below that of the magnetic oxide. These are .essential points which, I believe, clearly in-

Jan 1, 1906

By Henry S. Drinker

The Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been ' worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler prop erty, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the four teen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbon aceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meet ing, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone walls in V-shape running from the apex of the V towards the out crop, were built to cot the fire 06 and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

By H. Q. Golder

With the development of open-pit mines of ever increasing depth, the stability of the pit slopes in soil and rock is of growing economic importance. How is it, considering the newness of the problem that we know anything at all about the stability of man-made slopes? How much do we know and how did it all begin? We can make a reasonable estimate of the stability of a slope in soil, but we know as yet woefully little about slopes in rock because the problem is much more complex. It is only with the development of the capacity of the computer to handle wearisome calculations that any but the simplest of stability problems in rock have become possible of solution. But what we do know is a guide of immense value in the design of slopes in rock. But remember that the computer is a great elevator; it takes everyone's feet off the ground! So our study began with soils and what is now known as "Soil Mechanics", which is a translation of the German term "Bodenmechanik". It is a pity that the title of Terzaghi's book "Erdbaumechanik" was not used instead. But here the task of the translator is difficult because English lacks the facility of German to string together several words and make a new one whose meaning is unequivocal. Thus, we have the three German words 'Erde' 'Bau' and 'Mechanik'. 'Erde' means "earth" in almost all the English senses including "soil". 'Bau' and 'bauen' convey the meaning of building and construction, and 'Mechanik' means "mechanics" which includes statics and dynamics and the 'mechanics of materials', etc. So that a correct translation of the German is a phrase like "the mechanics of construction with, in or on, earth or soil." However we are stuck with 'Soil Mechanics' and that is where it all began. Now this study or subject did not begin with 'Terzaghi' although his contribution to the subject is unquestionably greater than that of any other single person. Every scientific discipline has its 'classical problem' and that of soil mechanics is 'the earth pressure problem' and it began in the 17th century. In fact, it probably began before this with the introduction of gunpowder to Western Europe in about the 15th century, but the first known reference to the problem was by Vauban, a distinguished French military engineer who lived from 1633 to 1707 and who gave rules for the dimensions of retaining walls from 6 to 80 ft. in height. The soil properties were not mentioned by Vauban probably because the rules were intended to be applied to fortifications only, but Poncelet (1840) claimed that Vauban's rules were based on a theory, and not simply on military and practical

Jan 1, 1972

By D. Turnbull

RECENTLY it has been shown that aggregates of small liquid droplets of tin,' mercury' or gallium' kept from intercommunicating by suitable films do not solidify at an appreciable rate unless the supercooling is very much greater than that usually necessary to cause a large continuous mass of the metal to solidify. For example oxide-coated tin droplets1 (1 to 10 micron diam) must be supercooled 100" to 110°C before their rate of solidification becomes rapid, although large continuous masses of liquid tin usually begin to solidify when supercooled 30" or less." These experiments have been interpreted' on the hypothesis that nucleation of crystals in large continuous metal samples is almost always catalyzed by accidental inclusions. Therefore, if the metal is dispersed into a number of isolated droplets large in comparison with the number of inclusions, most of the droplets should not crystallize until a temperature sufficiently below the thermodynamic melt- ing point, T0, has been reached to permit an ap-preciable rate of homogeneous (noncatalyzed) nu-cleation. In general this temperature is very much less than the temperature at which the rate of heterogeneous (catalyzed) nucleation is appreciable. If this interpretation is correct then investigation of the kinetics of crystallization of small droplet aggregates should be one of the most fruitful methods of obtaining information about the homogeneous formation of crystal nuclei in liquids. In this paper the results obtained on gallium and mercury are reported more fully. In addition, results on the supercooling of aggregates of liquid bismuth and lead droplets are included. Experimental Procedure Some care must be exercised in the choice of a barrier to prevent the liquid droplets from coalescing lest the barrier itself catalyze the formation of crystal nuclei. From this standpoint, the most desirable barrier is vacuum or inert gas, but, because of the difficulty of experimental arrangement, solid compounds and adsorbed films have been selected. There are two guiding principles in the selection of compounds as barriers in addition to the requirement that they prevent coalescence of liquid droplets. First, the compound should be almost insoluble in the liquid metal and second, its lattice structure should be quite unlike that of the forming metal crystal. Even so, there is no a priori assurance that the solid compound film will not catalyze to some extent the formation of metal crystal nuclei. An adsorbed protective monolayer is less likely to be catalytic than a crystal compound film, but it is not often possible to find a monolayer that is stable under the experimental conditions. Also, it is desirable, though not generally essential, that the aggregate of droplets be prepared by breaking up the massive metal rather than from a powdered compound of the metal.

Jan 1, 1951

By Gerald A. Munson, Fremont F. Clarke

DURING recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodu-mene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S. Lithium Corp. of America, during its rapid development and growth, has successfully employed three different methods of concentration: 1) hand sorting, 2) Heavy Media separation, and 3) froth flotation. Each method, though economic in its sphere, is becoming outdated as extractive techniques improve. The most recent development has taken place at Lithium Corp.'s new operation in North Carolina, where the extractive process yields lithium compounds directly from mined rock without an intervening concentrating step. Until 1954 Lithium Corp. mined only in the southern part of the Black Hills of South Dakota, where the various types of lithium-bearing pegmatite could be used to develop untried processes of beneficiation. Concentrates from these operations are shipped to the corporation's chemical plant in St. Louis Park, Minn., where actual extraction of lithium and production of commercial compounds takes place. Nature of Deposits The geology of the southern Black Hills pegmatite deposits is admirably presented by a U. S. Geological Survey publication.' Only the factors pertinent to exploitation need be mentioned here. Lithium Corp. has been interested primarily in three deposits, the Edison, the Mateen, and the Longview-Beecher No. 2. The history of these deposits dates back to the mining boom of 1880 to 1900 in the Black Hills, when most of the deposits were prospected for tin by the ill-fated Harney Peak Tin Mining Co. The three deposits described here, however, lay idle and unwanted until Lithium Corp. opened the Edison mine in 1943 and the Mateen and Longview-Beecher No. 2 in 1951. Edison Deposit: The Edison deposit is about a mile southeast of Keystone, S. D., on the northeastern flank of the Harney Peak uplift. The deposit consists of no less than four and probably at least six separate pegmatites that coalesce in a central mass from which the individual pegmatites finger outward and downward in complexly folded schist and gneiss beds of the country rock.

Jan 1, 1956

By John W. Bell

In the introduction to an excellent pamphlet, John Gross' makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 16, 18. 19. 21, 22, 23, 24, 30, 34). concluded that a foundation lor the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.I One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur 0. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 232,3 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger's was a true hypothesis and Stadler's false. The evidence in a third paper4 will be employed to prove that Stadler's hypothesis, when examined experimentally, is worthless. Stadler's Hypothesis Worthless It is the writer's opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler's hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left—the Rittinger hypothesis. Gates' Opinion What information is available in Mr. Gates' paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things. that many more of Stadler's energy units are obtained per foot-pound-applied in coarse than in finc crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger's theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1943

By John W. Bell

In the introduction to an excellent pamphlet, John Gross' makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 16, 18. 19. 21, 22, 23, 24, 30, 34). concluded that a foundation lor the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.I One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur 0. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 232,3 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger's was a true hypothesis and Stadler's false. The evidence in a third paper4 will be employed to prove that Stadler's hypothesis, when examined experimentally, is worthless. Stadler's Hypothesis Worthless It is the writer's opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler's hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left—the Rittinger hypothesis. Gates' Opinion What information is available in Mr. Gates' paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things. that many more of Stadler's energy units are obtained per foot-pound-applied in coarse than in finc crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger's theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1943

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By L. O. Bacon, D. O. Wyble

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,1,2 one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,1 and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hardwoods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magneticc anomalies they produce.

Jan 1, 1952

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.'- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers' have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.' The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.' The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

By A. J. Garnier, N. H. van Lingen

Rock downhole is known to be lesc. drillable than when brought to the surface. This must be ascribed mainly to the presence under downhole conditions of a pressure differential across already made chips, which hinders their being lifted. The pressure differential has partly a static and partly a dynamic origin. Balling-up of bits is another consequence of this pressure differerztial. Reduction in penetration rate owing to an increase in the strength of the rock is governed by the difference between the mud pressure and the pressure of the for/nation pore liquid. Rotationally symmetric geostatic stresses have 170 effect on drillability. Fracture of rock when drilling will be brille in most cases. The above is supported by laboratory drilling experiments with drag bill and roller bits an elevated mud, pore, and confining pressures On rocks differing in strength and permeability. INTRODUCTION In oil well drilling drillability of rock is found to decrease with increasing depth of the hole. Naturally deep rock will be more compacted and, therefore, harder to drill than shallow rock of the same type. However, apart from this the drillability of a sample of deep and compacted rock brought to the surface is generally much higher than in its original location downhole. In view of the economic implications of this reduction in drillability, it seems worthwhile to analyze its causes. The origin clearly has to be sought in the difference of environment. The only conceivable factors would seem to be the presence of mud under pressure, the pressure of the formation pore liquid, and the overburden of the rock. Down the borehole the rock is compressed triaxially by mud pressure and overburden. It is well known that the strength of rock is increased when confined by external pressure1. Various authors have, therefore, ascribed the difference in drillability mainly to the strengthening of rock by triaxial compression. Another factor, mentioned by Bobo and Hoch5, is that forces. including "pressure differential forces", tend to hold a dislodged particle in place. However, the conditions determining their magnitude are not clarified nor is their effect on drilling rate assessed. In the laboratory, drilling experiments on pressurized samples of rock yielded evidence that pressure differential forces holding the chips down are the major factor in reducing rate at depth. This paper describes the experiments and shows how the results enable both a qualitative and a quantitative interpretation of the factors determining the effect of chip hold-down on drilling rate. The implication with respect to balling-up and jet action is also discussed. The greatcr part of the experiments were performed in the pressure vessel shown in Fig. 1. The spacc between the sample of rock and the vesscl is divided by "0" rings into three separate chambers. The rock sample is confined laterally by pressurized oil in thc middle chamber. Penetration of oil into the sample is prevented by partly jacketing it with brass foil. Thc pressure of the drilling fluid in the hole can be adjusted via the upper chamber. Permeable rock specimens arc water saturated before being drilled. With a properly plastering mud as drilling fluid the pressure of the pore water can be adjusted independently via the lower chamber.