Search Documents

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

By Wm. D. Owsley, R. E. Moeller

In the petroleum industry, the process known as oil well cementing is the equivalent of pressure grouting in the mining and construction industries. The science of oil well cementing has been known and practiced for many years. At the present time it has been brought to a high degree of perfection in the handling of many different types of jobs, all of which are known as oil well cementing. In order to understand more easily these processes, we will discuss briefly several different types of oil well cementing jobs, the purposes for which they are performed, and the methods of their accomplishment. It is believed that some of .these procedures, in a modified form, can be applied to pressure grouting projects in general. Originally, oil well cementing consisted of placing a neat cement slurry about a steel casing set in a bore hole. Cement is used about these casings to protect them from the corrosive effects of ground waters, to protect the oil and gas zones from encroachment of undesired water from other levels, to prevent the blowing out of high pressure oil and gas zones from shallow levels, and to strengthen generally and support the casing being placed in the bore hole. After the bore hole is completed to the desired depth, casing is run into the well, pumps are attached to this casing and circulation of the mud fluid in the hole is established; this circulation being from the inside of the casing into the annulus about the casing, and thence back to the surface. Next, a cement slurry is mixed and pumped into the inside of the casing string, A plug, which acts as a piston within the casing, is placed above the cement slurry. This is to separate the top of the cement slurry from mud or water which is used to shove the cement down through the casing and out into the annulus. This plug further serves the purpose of shutting off against a baffle in the bottom end of the casing string, thus stopping the flow of cement out of the casing and leaving the shoe, or lower end of the casing, surrounded by cement and also filling the annulus there above. Casing strings cemented in the above described manner may vary in length from a few feet of large diameter pipe to very long lengths of smaller pipe. As of the present date the longest string of casing which has yet been cemented is some 16,600 ft deep. As a general rule, the deeper the well and the more cement slurry used, the higher the pressures which are required to place the slurry. In parts of West Texas, it is not uncommon to use 4000 sacks to cement a single string of casing in place. Machinery used to mix the cement and place it into the casing is mounted on heavy duty, powerfully equipped trucks which are capable of negotiating any type of highway or country roads. These trucks

Jan 1, 1949

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By F. E. Lathe, G. A. Guess

This investigation was started with the idea of determining whether copper-nickel mattes might not have a lower flowing temperature than copper mattes, and thus perhaps aid in accounting for the difficulty so far experienced in attempts at pyritically smelting copper-nickel ores. We have used the term flowing temperature to avoid confusion with the usual melting temperature. The idea at first was that there might be a greater viscosity range in the one matte than in the other. In the early experiments it was in our minds to determine the relative fluidity of the mattes at a given temperature. Looking to this end we tried pouring equal quantities of matte at the same temperature down an inclined graphite slab, and comparing the distances traveled. Results from such experiments were not satisfactory. We next tried pouring equal quantities at the same temperature through a drilled hole in an Acheson graphite crucible, timing the flow with a stop watch, the whole operation being carried out in the muffle. The flowing temperatures of the mattes tried in this way appeared to be about the same, and there was no marked difference in their fluidity when well fused. Oxidation gave some trouble. These experiments finally led to the adoption of the following apparatus which we thought at the time was wholly original with us, but which we have since found was described by W. McA. Johnson.l The tray used was a slab of graphite 8 in. long, 2 in. wide and 1/4 in. thick. It had six holes, into each of which sat a cup of Acheson graphite. Centrally in the bottom of each cup was a vertically drilled hole 3/16 in. in diameter and 1/2 in. long. The mattes to be tested were put into the cups, in a solid piece. The cups were covered with inverted Battersea "A" cups. The tray was put into the muffle of a gas-fired furnace. Supports on each end held the tray about 2 in. from the floor of the muffle. Under

Jan 1, 1917

By F. E. Poulson

The discovery of two new fields, Van, in East Texas, and Darst Creek, in the Balcones fault zone, is the outstanding development in 1929. The first six months was one of the most inactive periods in the history of East Texas. Five of the interior salt domes, which had been so eagerly sought as a result of the Humble Oil & Refining Co.'s strike on the Boggy Creek dome in 1927, were drilled with discouraging results, and the Boggy Creek field itself had fallen far short of expectations. Kelsey, a structure of considerable magnitude and extent in Upshur County, was equally disappointing; the Amerada Petroleum Corpn.'s initial test on this structure was dry. The situation improved in the latter half of the year. On Oct. 13, 1929, the Pure Oil Co. discovered the Van field. This gained for East Texas a permanent place in point of future potential production. There was a similar reaction in the Balcones fault zone. The Salt Flats (Bruner) field, the important discovery of 1928, proved its rating as a second Luling, but on account of repeated failures to extend the productive zone, wildcatting during the first half of 1929 in the Luling district was dilatory. In July, however, Darst Creek, a third fault-line field of majori mportance producing from Edwards limestone (Lower Cretaceous), was discovered. Retarded as development in this field has been by various attempts at proration, interest in the Balcones fault zone fields centered on Darst Creek as the year 1929 drew to a close. Development in East Texas Fields Discovered during 1929 Van.—The discovery well, Jarman No. 1 of the Pure Oil Co., is near the town of Van in the southeastern part of Van Zandt County, Texas. It is 55 miles northeast of the Powell field in Navarro County and 45 miles west of north from the Boggy Creek field in Cherokee and Anderson counties. Early in 1927, the Van area was submitted to seismographic exploration and outlined as a large anticline, the apex of which seemed to be

Jan 1, 1930

By Thomas Egleston

DURING the year 1873, my attention was called to the frequent accidents, resulting from the breaking of rails, on the different railroads in this' country, and I was requested to investigate the subject. The plan of investigation I proposed was to ascertain, in as many cases as possible, the exact hist* of broken rails, both in this country and in Europe; to collect information in Europe relating to the tests which rails used there were required to undergo, and to experiment upon the pieces of rails broken on the road, with a view to ascertain whether their fracture was due to their chemical constitution, bad manufacture, to a reduction in strength owing to temperature, or to physical changes in the constitution of the rail. The investigation was commenced by the collection of statistics, and for this purpose I spent several months in Europe, collecting information on the subject of broken rails, as well as the life of iron and steel rails generally, and inquiring into the systems of purchasing and of testing them employed by the railroads there, intending, on my return, to make a series of analyses of rails broken, both in this country and in Europe; to ascertain, if possible, how far great cold had an influence on the fracture; to examine whether the rail broken, either on the road or afterwards, underwent, at or about the fracture, any physical change, and to make a series of experiments on the strength of rails manufactured in the United States or sold in the American market. Unfortunately, the panic of 1873 came on, just before my return from Europe, and prevented the carrying out of the larger part of the plan proposed; as, however, I had collected in the meantime, a large number of statistics of different kinds from all parts of Europe, and had made a number of interesting experiments and investigations, I have thought it would be worth while to communicate some

By Frederic H. Lahee

The purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexial fault zone, and to show how the apparently very irregular well logs in these fields may be use? for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30" east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity River at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fauil zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a downthrow on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults. Oil Fields Associated with Mexia Fault Zone When speaking of oil fields associated with the Mexia fault zone, we refer only to those now producing from the Woodbine sand. In this category belong the Mexia, Currie, Old Richland or Seay-Cranfill, Powell, and New Richland fields, named in the order of their discovery (see Fig. 1). Subsequent development may prove that the gas found in the Boyd Oil Co.'s Connor well, north of Kerens, is coming from another pool in the same fault zone.

Jan 1, 1925

By H. J. Wasson

Published literature regarding the nation's oil reserve has been largely concerned with the estimated quantities in sight in known producing fields. This proved reserve has never been large in relation to demand. It has been the practice to consider the total future reserve (beyond that in sight within known fields) in the light of the broad potentialities of vast areas of partially explored sedimentary rocks, which are regarded as possible oil territory. Until recently, but little attention has been given to the rate at which the unexplored potentialities may be. converted into the proved reserve classification. To a certain extent, therefore, our contemporary viewpoint on the subject of national oil reserves is characterized by a pronounced contradiction. On the one hand, we measure known reserves as sufficient for only a few years of consumption—i.e., relative scarcity; on the other hand, we are confident that millions of unexplored acres will yield many new oil fields and that countless deeper productive formations underlie many of our known productive fields—i.e., infinite abundance. Of greater significance than the quantitative measure of either of these reserve classifications is the rate at which reserve replenishment must be accomplished in order to maintain an adequate time supply of proved oil reserves. The accumulation of geological data covering broad areas supports the belief that the remaining undiscovered oil reserve is exceedingly large. The distribution of oil in sedimentary formations of practically all ages, from Cambrian to Recent, is suggestive of almost unlimited possibilities; and the relatively small proportion of these possible areas that has been intensively explored in this country is a further index of the probable magnitude of the undiscovered future reserve. The implication that may reasonably be drawn from these observations is that oil, though distributed with less regularity and concentration than its related hydrocarbon, coal, nevertheless is a relatively abundant natural commodity of which the exhaustion appears remote. Final exhaustion of our oil reserve, if not infinitely remote, is a future contin-

Jan 1, 1937

Cyril w. Knight, Toronto, Ont., Canada (communication to the Secretary*).—Mr. Hore's paper presents an interesting summary of our knowledge of this important mineral field ; and is therefore acceptable as giving information which our Transactions did not already contain, although it presents little or nothing not made known by other writers before 1906, when Mr. Hore began work in the field as a student assistant. Contributions of this kind, however, should be made completely valuable by such references to previous work as will enable the reader to follow to their original sources the theories or conelusions stated by the author. It is quite natural, and even excusable, that a new observer should find novelty in his on observations—especially if he is not acquainted with the work of predecessors in the same field. Moreover, the independent repetition of an observation or conclusion has a distinct value as a confirmation, though it may have none as a discovery. But the publication of it, without reference to its predecessors, may place the author in an unfavorable light as either ignorant of the history of his subject, or willing to claim credit to which he is not entitled. Of the latter fault, I do not accuse Mr. Hore ; but I cannot wholly acquit him of the former. Without disparaging his intelligent work, I must point out that his paper, as it stands, might easily give the impression that he claims originality for many statements which are by no means new, and that he emphasizes unduly his own publications. Thus, his remark (p. 481) "I have described the silver-fields in a general way in my paper " (not yet published), should have been accompanied with reference to some of the numerous papers, already published, which describe these fields. Again, on p. 486, he refers to four papers of his own on the Porcupine gold-area, but neither in the text nor in the appended

Jan 1, 1912

By C. E. Mills

Studies of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations. Geology and Structure1 The ore deposits of the United Verde are of the massive sulfide, schist-replacement type. A structural anticline formed by the intrusion of diorite between bedding planes of steeply dipping and severely folded greenstones and porphyry localized the deposit of sulfide. The mineralized zone is of great horizontal extent varying from 200,000 to 400,-000 sq. ft., and extends from the surface to the lowest levels at a steep dip of from 50° to 75. The irregular interfingering of the sulfide with

Jan 1, 1934

By Charles E. Reed

With the increasing importance of clay in drilling operations which demand more precise and exacting control over its behavior, there has come the realization that most of our present methods of control over many of its important properties still represent more of an art than a science. Such a situation with respect to a material of such industrial significance is unfortunate, and naturally many investigations have been conducted to improve our knowledge. In general, these investigations have revealed the complex nature of clay behavior and while sometimes they may not have seemed to contribute directly to a solution of the field operator's problems they have been of inestimable importance in bringing to light the broad fundamental scientific principles upon which must be based any effective working theory correlating the known facts of clay behavior and predicting profitable new lines of attack for its improvement. Major Facts Concerning Behavior of Clays In the study of clays, as in that of most other colloidal materials, it has been impossible to make progress by the study of isolated facts. On the other hand, analysis of large groups of facts, many of which seem at first completely unrelated, can lead to a deeper insight into the structure of clays and the mechanism of their behavior. It will be well to list the major facts on which the analysis here presented is based, starting with those that have emerged repeatedly from past investigations and which thereby constitute an impregnable foundation upon which must rest any comprehensive theory of clay behavior: 1. Clays consist of hydrated aluminosilicates of extremely fine and variable particle size. 2. Suspended in water, clays exhibit variable degrees of swelling, depending upon their origin and upon the chemical and colloidal nature of any other substances present. The magnitude of the swelling is a direct indication of the extent to which the clay has become dispersed.

Jan 1, 1938

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17' There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By B. S. Butler

PART I SUMMARY CERTAIN relations between the formation of ore deposits and other geological processes are pretty generally accepted, namely: that many ore deposits are closely associated with igneous activity; that ore deposits accompany certain types of intrusive bodies, notably batholiths and stocks, and that they are concentrated near the tops of such bodies; that igneous activity occurs in belts of strong folding and faulting; that folding and faulting are greatest in basins of extensive sedimentation and least in areas of erosion or slight sedimentation; that areas of erosion or slight sedimentation and of heavy sedimentation persist over long periods and exert a major control over structure, igneous activity, and ore deposition; that cycles of erosion, deposition, folding and faulting, igneous activity, and ore deposition, have been repeated through geologic time resulting in rather definite periods in which metal deposits have formed. In short, ore deposition is but one phase of a series of closely related geological events. It is attempted in this chapter to point out the relations of these interreacting geologic processes to the distribution of ore deposits in the western United States. Three great periods of mineralization are recognized; pre-Cambrian, post-Jurassic, and late Cretaceous-Tertiary. In distribution the deposits of the three periods, with certain exceptions, show a concentration about two large positive areas, the Colorado plateau and the Columbia plateau, which suggests a causal relation. The most general age divisions of the rocks of the Cordilleran region of the United States are (1) pre-Cambrian, and (2) Cambrian and later rocks. The pre-Cambrian rocks are exposed mainly through the Rocky Mountain belt from the Canadian boundary southward to Arizona and westward through Arizona to southern California. They have commonly

Jan 1, 1933

By A. A. Bauer, F. A. Rough, G. H. Beatty

AS a result of recent studies, the constitution of the zirconium-uranium system has been fairly well defined. A diagram for the system is shown in Fig. 1. However, both oxygen and nitrogen are known1-3 to have a pronounced effect on the limits of both ß- and e -phase regions. It has been shown that small amounts of oxygen severely constrict the compositional limits of these phase regions in the ternary zirconium-uranium-oxygen system. A previously published tentative diagram shown in Fig. 2 illustrates the ß-phase constriction resulting from oxygen additions. Generally, iodide zirconium has been used in constitutional studies of zirconium-uranium alloys. While this is the highest purity material available, cast iodide zirconium-uranium alloys will generally average from 200 to 300 ppm 0 and from 50 to 60 ppm N. Thus, while the constitution of the zirconium-uranium system is fairly well defined, it must be realized that this definition applies to alloys containing in the vicinity of 250 ppm 0 and 50 ppm N. The present investigation was undertaken to accurately determine the boundary between the ß-plus-P and ß phases at a single temperature in the binary zirconium-uranium system by quantitatively

Jan 1, 1959

Edgar Hall, Tenterfield, New South Wales (communication to the Secretary): Mr. Klepetko* asks for information showing at what percentage antimony and arsenic, as impurities, begin to affect injuriously the quality of brass.

Jan 1, 1899

By Frederick Prime

In this supplementary list no titles to which an * is prefixed have been seen by the compiler; and he will be most thankfu1 to have any omissions or inaccuracies in the list sent to him to be published as a second supplement in the next volume of the Transactions. The author is indebted to Messrs. Robert Clarke, of Cincinnati; Thomas Macfarland, of Towanda; Professor F. W. Simonds, of Chapel Hill; and Professor J. J. Stevenson, of New York, for valuable assistance. Cedar Point IRON Company, Baltimore, July 31st, 1880. Alabama. Geological Survey of Alabama. Report of Progress for 1877 and 1878; by Eugene A. Smith, State Geologist. Montgomery, 1879. 8vo., 139 pp., and 4 maps.

Jan 1, 1880

By Edward Wisser

The Pachuca silver district, situated about 100 kilometers northeast of Mexico City (Fig. l), covers roughly the southeastern half of the Sierra de Pachuca. The latter is a mountain range with northwest trend, and forms a part of the northeastern rim of the topographic basin known as the Valley of Mexico. The length of the Sierra proper is about 50 km., its greatest width about 9 km., and it rises to a maximum of 600 meters above the general level of the basin floor. The Pachuca district consists of two contiguous subdistricts, the Pachuca area and the Real del Monte area. The center of the Real del

Jan 1, 1937

By M. H. Merriss

In the last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, 'Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes' that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 1, 1926