Search Documents

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.

Jan 1, 1956

By G. S. Hume

The production of petroleum in Canada is relatively small in proportion to the amount of oil consumed. Production figures are given in Tables 1 and 2, which show that the production in Alberta for 1934 was more than for the whole of Canada in 1933. The production of natural gas for Canada is shown in Table 3, In Turner Valley, the largest producing gas and oil field in Alberta, seven naphtha wells from the Paleozoic limestone and one crude oil well from Lower Cretaceous strata were completed during the year. Six-

Jan 1, 1935

By Angelus S. C. Owili-Eger

This paper discusses a model for groundwater quantity prediction at operating sections of underground mines. The approach involves the development of a mathematical model for the movement of water through an integrated (unsaturated-saturated) flow domain within a definable watershed. The model is programmed for the IBM 370/168 computer using the method of finite difference approximation coupled with a finite element analysis. The conceptual and computational aspects of the model have been validated with both experimental and field data and applied to an active coal mining operation located in central Pennsylvania.

Jan 1, 1977

By H. M. Hobart

This paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the greatest economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of_ Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox, of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per sq. in. (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per sq. in. (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows: Works Carbon Content for Plates 1/4 In. Thick 1 In. Thick A..................... 0.14 0.23 B..................... 0.14 0.25 C2.................. 0.19 0.25 D................. 0.20 0.30 E Upper limit..... 0.35 Lower limit..... 0 24 0.29 Upper limit,.... 0.25 0.30 Lower limit..... 0.21 0.27 Upper limit..... 0.25 0.35 Lower limit..... 0.22 0.28

Jan 1, 1920

By William K. Callaway

Cominco American has operated the Magmont Mine for 16 years as a traditional open stope room and pillar mine. Diminishing ore reserves and the discovery of high grade ore zones over 90' in thickness caused consideration to be given to hydraulic sandfilling as a method of ground support to increase pillar extraction and mine life. This paper will review the results of sandfill testing. Plans for underground experiments, and operational plans for the future will also be discussed.

Jan 1, 1984

By J. H. McCarthy, J. M. Botbol, R. B. McCammon, G. H. Gott

Four areas have been identified as favorable drill site locations for determining whether a suspected porphyry copper deposit exists in Rowe Canyon, NV. Favorability is bated on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for zinc, silver, aresenic, antimony, and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1983

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

By Franklin G. Pardee

WARTIME depletion of the reserves of iron ore in the Lake Superior region of the grade and character now being shipped down the Lakes was serious. The time has come to take stock of the resources that remain in order to plan our future program of supply for our blast furnaces and protect, as far as possible. the tremendous investment made in the Lake Superior iron mining industry. Hugh M. Roberts and William H. Crago have estimated the reserves of the Lake Superior region in the United States at two billion long tons. These reserve figures are of direct-shipping ore and those concentrates produced by methods now in commercial use or those methods that may be expected in the near future. In their estimate they have assigned 392 million long tons to the Michigan ranges (all reserves in long tons) : 112 million tons for the Gogebic. 140 million tons for the Menominee, and 140 million tons for the Marquette.

Jan 1, 1948

By N. E. Rogen, N. J. Grant

AGE-hardening in nickel-chromium-titanium-aluminum alloys in the composition range characterized by the Nimonic alloys, is dependent upon the precipitation of the Ni3(AI,Ti) (y') phase.1 This phase is found to precipitate at about 700°C.1 Ni,Al is a face-centered-cubic ordered structure with a lattice parameter of 3.560 A. The atomic configuration is such that the aluminum atoms occupy the cube corners and nickel occupies the cube faces with titanium substituting for the aluminum preferentially. A maximum of three out of every five aluminum atoms can be replaced by titanium atoms in the -y 'phase.' When the solubility of the y'-phase is exceeded for titanium the T(Ni,Ti) phase is formed. The T-phase is an ordered close-packed hexagonal intermetallic structure which shows little solubility for the other elements in these alloys. The lattice parameter for T-phase is a - 2.5454 kr and c = 8.2900 kx units."

Jan 1, 1959

By C. M. Wayman, M. Miyagi

COMPARED to many of the binary alloys of iron, Fe-Ir alloys have received very little tud.'' Virtually nothing is known about the Fe-Ir equilibrium diagram' except for a few details concerning the liquidus-solidus positions for dilute iron-based alloys. It is reported1 that the y to a transformation temperature in Fe-Ir alloys (up to 40 wt pct Ir) is composition-dependent, varying from -900°C for pure iron to 0" to 100°C for Fe-40 pct Ir in an almost linear manner. The y to a transformation appears to be reversible,' the transformation hysteresis width increasing with increasing iridium content. In a qualitative way, the composition dependence of the y to a (and vice versa) transformations appears similar to those in the widely studied Fe-Ni system. In that the y phase (in Fe-40 pct Ir) can transform at -1000C, it

Jan 1, 1967

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By Anthony Folger, Charles E. Straub

Kansas produced 38,150,878 bbl. of oil in 1928 and 40,658,170 bbl. in 1929, thereby retaining its rank as fourth among the oil-producing states of this country. Production for 1928 was less than that for 1927 (Fig. 1) because of a decrease in the number of completions, but the average initial production per well (Table 1) shows an increase due to the completion of wells of comparatively large capacity in the new Valley Center pool of Sedgwick County. This increase in average initial production per well was further augmented during 1929 by completion of additional wells of comparatively large capacity in the Valley Center pool and the new Greenwich pool of Sedgwick County. Production for 1929 exceeded that for 1928 and threatened to exceed all records except that of 1918, however, production was prorated in

Jan 1, 1930

By T. M. Morris

THE following data have been compiled from in- formation submitted by 24 plants in answer to a questionnaire sent to cyclone manufacturers and to companies using cyclones for wet classification, either for closed circuit grinding or for desliming.

Jan 8, 1957

By George M. Humphrey

It is indeed a pleasure for me to have this opportunity to discuss with you a subject which I find infinitely interesting and intriguing - namely, world-wide iron ore supply and demand. We will be examining the following: (i) current iron ore production and requirements; (ii) the major ore producing countries; (iii) the seaborne iron ore trade; (iv) ore grades or types; and (v) future requirements. For those who may not be familiar with the iron ore mining industry, it may be useful to know at the outset that our industry has been plagued with overcapacity for the past seven years. The optimism which prompted substantial expansion of productive capacity in the early to mid-1970's has unfortunately proved to have been unfounded. I shall begin by describing where we are today as well as a little about how we got there. In the latter regard, it's not so much that historical knowledge will solve any of the industry's problems or provide clairvoyance with regard to the future. Rather it's a feeling on my part that some knowledge of the past will provide a useful perspective capable of enhancing our analysis of future trends. At the time of writing, the most recent year for which we have definitive world-wide iron ore production and consumption statistics is 1980. In that year the world consumed approximately 859 million metric tons of iron ore to produce approximately 510 million metric tons of primary iron consisting of 502 million tons of pig iron and 8 million tons of sponge iron. Crude steel production for the same period attained a level of 719 million metric tons. Because it is possible in today's world to produce steel without consuming iron ore simply by melting scrap, the key statistic insofar as iron ore demand is concerned is primary iron production. In 1980 the ratio of iron ore consumption to primary iron production was 1.68:1.00. The comparable ratio over the past seven years has varied from 1.63 to 1.87 and averaged 1.72:1.00. All the same, as a practical matter crude steel production and iron ore consumption tend to parallel one another closely, and for the time being a good rule of thumb is that to produce an average ton of crude steel requires 1.20 tons of iron ore. Let's turn our attention now to the regions where the 859 million tons of iron ore necessary to support 1980 world-wide iron and steel production were produced. Not surprisingly, most of the ore was produced in the same region where it was smelted. In round numbers 65% of the world's iron ore production is currently consumed in the same general region as it is produced, while 35% enters the seaborne trade and is transported in ocean vessels to a more remote consuming area. Approximately 85% of the world's seaborne iron ore trade is directed to the Western European and Japanese markets, both of which are almost entirely dependent on off-shore sources for their mammoth iron ore requirements. The following tabulation lists, in order, the twelve leading iron ore producing countries in 1980 as well as their percentages of total and free-world production; in addition their export potentials are presented. As a group these countries accounted in that year for 89% of world-wide production which stood at 871 million tons. Leading World Iron Ore Producing Countries [ ] One will first note that world iron ore production is dominated by the top four producers - namely, the U.S.S.R., Brazil, Australia and the U.S.A. - which together accounted for nearly 60% of total 1980 production. Of these four major producers the U.S.A. and the U.S.S.R. produce almost exclusively for consumption in their own regions, whereas Australia and Brazil produce primarily for the seaborne export trade. In fact Australia and Brazil accounted for about 50% of all seaborne iron ore trade in 1980! It is also interesting to note that Australia, Brazil, the U.S.A. and Canada accounted for nearly 60% of free world iron ore production in 1980. Once again the importance of Australia and Brazil shows itself, with their share alone of free world production reaching 35%. As has already been noted, a significant 35% of the world's iron ore production in the year 1980 was

Jan 1, 1982

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By Marcus A. Grossman

THE institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it," All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we should review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks.

Jan 1, 1946

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By B. K. Mozumdar

This paper describes the development and application of a dynamic simulation model of ground movement in an underground mine. Ground movement and related stress distributions with or without stowing are computed as the mining face advances. Pressure profiles plotted for different face positions indicate the presence of a front abutment with a maximum value of four times the original ground pressure but no back abutment in the gob. The surface strain is considerably reduced with increase in packing density in the gob up to a certain value. Beyond this value, the reduction in the strain is minimal, indicating an economic level of packing. As a result of model experiments with different physical systems and geological parameters, it has been concluded that when one of the coordinates for the subsidence and the strain curves is made dimensionless in terms of the critical width, the relationship will hold true for all physical situations. This was in agreement with the NCB observations for different panel lengths.

Jan 1, 1977

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946