Search Documents

By H. J. Ramey

The wellbore acts as a storage tank during drawdown and build-up testing and causes the sand-face flow rate to approach the constant surface flow rate as a function of time. This effect is compounded if non-Darcy flow (turbulent flow) exists near a gas wellbore. Non-Darcy flow can be interpreted as a flow-rate dependent skin effect. A method for determining the non-Darcy flow constant using this concept and the usual skin effect equation is described. Field tests of this method have identified several cases where non-Darcy flow was severe enough that gas wells in a fractured region appeared to be moderately damaged. The combination of wellbore storage and non-Darcy flow can result in erroneous estimates of formation flow capacity for short-time gas well tests. Fortunately, the presence of the wellbore storage eflect permits a new analysis which can provide a reasonable estimate of formation flow capacity and the non-Darcy flow constant from a single short-time test. The basis of the Gladfelter, Tracy and Wilsey correction for wellbore storage in pressure build-up was investigated. Results led to extension of the method to drawdown testing. If non-Darcy flow is not important, the method can be used to correct short-time gas well drawdown or build-up data. A method for estimation of the duration of wellbore storage effects was developed. INTRODUCTION In 1953, van Everdingen and Hurst generalized results published in their previous paper3 concerning wellbore storage effects to include a "skin effect", or a region of altered permeability adjacent to the wellbore. Later, Gladfelter. Tracy and Wilsey4 presented a method for correcting observed oilwell pressure build-up data for wellbore storage in the presence of a skin effect. The method depended upon measuring the change in the fluid storage in the wellbore by measuring the rise in liquid level. To the author's knowledge, application of the Gladfelter, Tracy and Wilsey storage correction to gas-well build-up has not been discussed in the literature. It is, however, a rather obvious application. Gas storage in the wellbore is a conlpressibility effect and can be estimated easily from the measured wellbore pressure as a function of time. Several approaches to the wellbore storage problem have been suggested. As summarized by Matthews, it is possible to minimize annulus storage volume by using a packer, and to obtain a near sand-face shut-in by use of down-hole tubing plug devices. Matthews and Perrine have suggested criteiia for determining the time when storage effects become negligible. In 1962, Swift and Kiel' presented a method for determination of the effect of non-Darcy flow (often called turbulent flow) upon gas-well behavior. This paper provided a theoretical basis for peculiar gas-well behavior described previously by Smith. Recently, Carter, Miller and Riley observed disagreement among flow capacity k,,h data determined from gas-well drawdown tests conducted at different flow rates for short periods of time (less than six hours flowing time). In the original preprint of their paper, Carter et al. proposed that the discrepancy in flow capacity was possibly a result of wellbore storage effects. Results of an analytical study of unloading of the wellbore and non-Darcy flow were recorded by carter.14 In the final text of their paper, Carter et al.!' stated that they no longer believed wellbore storage was the reason for discrepancy in their kgh estimates. In view of the preceding, this study was performed to establish the importance of non-Darcy flow and well-bore storage for gas-well testing. In the course of the study. a reinspection of the previous work by van Everdingen' and Hurst' was made, and the basis for the Gladfelter, Tracy and Wilsey' wellbore storage correction was investigated and extended to flow testing. WELLBORE STORAGE THEORY As has been shown by Aronofsky and Jenkins,11-12 Matthews," and others, flow of gas can often be approximated by an equivalent liquid flow system. The following developnlent will use liquid flow nomenclature to simplify the presentation. Application to gas-well cases will be illustrated later. First, we will use the van Everdingen-HursP treatment of wellbore storage in transient flow to establish (1) the duration of wellbore storage effects, and (2) a method to correct flow data for wellbore storage. DURATION OF WELLHORE STORAGE EFFECTS When an oil well is opened to flow. the bottom-hole pressure drops and causes a resulting drop in the liquid level in the annulus. If V. represents the annular volume in cu ft/ft of depth, and p represents the average density of the fluid in the wellbore, the volume of fluid at reservoir conditions produced from the annulus per unit bottom-hole pressure drop is approximately: res bbl-- (V, cu ft/ft) (144 sqin./sq ft) psi -(5.615 cu ft/bbl)(pIb/cuft) ........(I)

Jan 1, 1966

By N. J. Myers, S. J. Nemeth

POWER in the mill at Appalachian Sulphides Inc. is provided by 86 electrical motors ranging from 1 to 200 hp and totaling 1200 hp. After a careful study of different types of support for these cables an expanded metal trough was chosen as the most suitable. One hundred and twenty feet of trough were installed in 18-in. width and 150 ft in 6-in. width. This trough carries all the power as well as the control circuits. Now that the electrical distribution system is complete it is clear that this type of cable supporting system offers many advantages. To handle the same amount of cable in conduit, for example, would have required such a jungle that wiring all the different motors and controls would have been very difficult, even for the original hook-up. In the Appalachian Sulphides operation it has been necessary to make changes from time to time in the wiring of the different motors. These changes are readily made with the present cable supporting system because the trough leaves the wires accessible for rerouting as needed.

Jan 1, 1958

By Samuel Dolbear

PUBLIC discussions of mine finance in the tech-nical press have been confined mainly to methods of providing funds for the development of pros-pects or other mining operations which have not reached the stage of productivity. The application of modern financing methods to mines which have behind them a successful record of net earnings has, for some reason, been given scant consideration by mine owners and managers. In a few conspicuous cases, such for example as the Anaconda Copper Mining Co., Chile Copper Co., and one or two others, industrial finance has been applied to mining operations on the scale and after the fashion of other operations. When extensions are needed re-course is usually had, however, to the sale of common stock, with the obvious disadvantage of diluting the holdings of every stockholder of record prior to such financing. In some cases, it has been sought to over-come this disadvantage by issuing stock purchase rights to shareholders of record. If the stockholder is in a position to acquire additional stock, he may then pre-serve his interest intact, otherwise he must suffer a dilution of his holding. If he purchases additional stock he is, from one point of view, paying more for his in-terest than he bargained for when he made his original purchase. In many cases development and equipment are paid for out of surplus or current earnings. It is sometimes most difficult to explain to a manager why he can afford to borrow money when funds are available from a sur-plus account. Nevertheless, industrial enterprises with adequate surplus accounts often finance new construc-tion by the issuance of bonds. Such a procedure enables the company to maintain its surplus intact, and to con-tinue the payment of dividends during a temporary period of unusual expenditures.

Jan 2, 1927

By G. W. Leney

Iron ores occur in such a wide variety of forms that nearly every kind of prospecting, geological knowledge, and geophysical technique has some application in the search for them. The type of orebody that is considered desirable depends on political and economic considerations, on transportation and markets, on the characteristics of the orebody, on the metallurgy of the ore, and on its comparison with other available ores. In North America, materials that can be efficiently processed into high grade concentrates and pellets are now the object of most exploration work. These are usually shallow, relatively unoxidized, metamorphosed iron formations that are particularly suitable for geophysical methods of exploration. Magnetic surveys are used for the direct discovery of new orebodies, for mapping stratigraphy and structure, and at times to locate oxidized zones in magnetic iron formation. Gravity mapping provides supplementary information, indicates gross tonnages, is useful in regional studies, and can discover non-magnetic orebodies. Electrical methods have not been fully exploited but self-potential, resistivity, applied potential, electromagnetic and perhaps induced polarization surveys all have restricted but highly useful applications. The use of all geophysical techniques promises to increase as the number of exposed easily discoverable orebodies decreases. A high consumption of steel, and consequently of iron ore is the chief characteristic of an industrial society and this consumption has been increasing at an average rate of about 35% every ten years for the past century. To supply this demand, iron ores and iron bearing materials in a wide variety of forms have been exploited on every inhabited continent and in nearly every country. Nearly every kind of prospecting, geological knowledge and geophysical technique has some application in the search for them. The type of orebody that is con-

Jan 1, 1964

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By M. Metzger, J. C. Bilello

Microyielding in 99.999 pct Cu occuwed in two distinct parabolic microstages and was substantially indeoendent of grain size at the relatiz~ely large grain sizes stzcdied. The strain recouered on unloading was a significant fraction of the forward strain and was initially higher in a copper-coated single crystal than in poly crystals. Results were interpreted in terms of cooperative yielding and short-range dislocation motion activated otter a range of stresses, and a formalism was given for the first microstage. It was suggested that models involving long-range dislocation motion are more appropriate for impure or alloyed fcc metals. THERE are still many unanswered questions concerning the degree and origin of the grain size dependence of plastic properties. In the microstrain region, a theory of the stress-strain curve proposed by Brown and Lukens,&apos; based on an exhaustion hardening model in which the grain boundaries limit the amount of slip per source, accounted for the variation with grain size of microyielding in iron, zinc, and copper.&apos; This theory assumes N dislocation sources per unit volume whose activation stress varies only with grain orientation. Dislocations pile-up against grain boundaries until the back stress deactivates the source, which leads to a relationship between the axial stress and the strain in the microstrain region given by: where G is the shear modulus, D the grain diameter, a the flow stress, and a, is the stress required to activate a source in the most favorably oriented grain.3 If this or other grain-boundary pile-up models are correct, then the reverse strain on unloading would be much larger for a polycrystalline specimen than for a single crystal. Also, the microplasticity would become insensitive to grain size if this could be made larger than the mean dislocation glide path for a single crystal in the microregion. These questions are examined in the present work on polycrys-talline copper and a single crystal coated to provide a synthetic polycrystal. EXPERIMENTAL PROCEDURE Tensile specimens 3 mm sq were prepared from 99.999 pct Cu after a sequence of rolling and vacuum annealing treatments similar to those recommended by Cook and Richards4-6 to minimize preferred orientation. Grain size variation from 0.05 to 0.38 mm was obtained by a final anneal at temperatures from 310" to 700°C. Dislocation etching7 revealed pits on those few grains within 3 deg of (111). For all grain sizes dislocation densities could be estimated as -107 cm per cu cm with no prominent subboundaries. The single crystals, of the same cross section, were grown by the Bridgman technique with axes 8 deg from [Oll] and one face 2 deg from (111). An anneal at 1050°C produced dislocation densities of 2 x 106 cm per cu cm and subboundaries -1 mm apart in these single crystals. A Pb-Sn-Ag creep resistant solder was used to mount the specimens, with a 19 mm effective gage length, into aligned sleeve grips fitted to receive the strain gages. All specimens were chemically polished and rinsed8 to remove surface films just prior to testing. The synthetic polycrystal was made by electroplating a single crystal with 1 µ of polycrystalline copper from a cyanide bath. Mechanical testing was carried out on an Instron machine using two matched LVDT tranducers to measure specimen displacement, the temperature and the measuring circuit being sufficiently stable to yield a strain sensitivity of 5 x 107. At the crosshead speeds employed, plastic strain rates were, above strains of 10¯4, about 10¯5 per sec for polycrystalline specimens and 10-4 per sec for the single crystals. Plastic strain rates were an order of magnitude lower at strains near l0- &apos;. A few checks at strain rates tenfold higher were made for reassurance that the initial yielding of polycrystalline copper was not strongly strain-rate dependent. Test procedures followed the general framework outlined by Roberts and Brown.9,10 An alignment preload of 8 g per sq mm for polycrystals, and 2 to 4 g per sq mm for single crystals, was used for all tests. These gave no detectable permanent strain within the sensitivity of the present experiments; although at these stress levels, small permanent strains are detectable in copper with methods of higher sensitivity.11 12 stress and strain data are reported in terms of axial components. RESULTS General. The initial yielding is shown in the stress vs strain data of Fig. 1. For polycrystals, cycle lc, the loading line bent over gradually without a well-defined proportional limit, and almost all of the plastic prestrain appeared as permanent strain at the end of the cycle. The unloading curve was accurately linear over most of its length with a distinct break indicating the onset of a significant nonelastic reverse strain at the stress o u, indicated by the arrows. The yielding in subsequent cycles, Id and le, had the same general character. The single crystal behavior, shown to a different scale at the right of Fig. 1, was different in that initially the nonlinear reverse strain was unexpectedly much greater than for polycrystals. It should be noted that these soft crystals had a small elastic

Jan 1, 1970

A bibliography of the use of pulverized coal for the years 1917 and 1918 has been compiled by the Library for the Institute. It comprises three typewritten sheets. Copies may be obtained by those interested at $2 per copy.

Jan 5, 1919

By J. K. Brooke, R. M. Dreyer

For mining engineers and geologists accustomed evaluating metallic mineral deposits, the problems inherent in determining the worth of non- metallic industrial minerals deposits for the chemical processing industry often comes as a rude shock. These difficulties lead to different, and often much greater, problems in financing the development of such deposits than would normally be anticipated for economic sources of copper, molybdenum, iron, nickel and other metallic minerals. The chemical processing industry is one of the two principal consumers of non-metallic mineral production, the other being the construction industry. In the last decade, the volume of industrial minerals consumed by chemical processers has in- creased by 30%, and further increases are forecasted. To satisfy this growing demand, many new sources of these minerals must be found and developed. For those of us who will become involved in such work, the following brief analysis of the major problems to be expected may be of help in developing a realistic approach to evaluating and financing such a deposit and selling the product to consumers.

Jan 8, 1962

Development of Technical Education for the Petroleum, Industry. By H C GEORGE (Min & Met, June, 260 2000 words) With a growth of 718 per cent in the petroleum industry from 1901 to 1931, there was a corresponding increase in the demand for technically trained men in the industry This was first met by increasing numbers of college graduates from the old established courses m chemistry, geology and engineering However, there began to be felt a need for scientists and engineers specially trained for the petroleum industry In 1912 the University of Pittsburgh established the first department in any university in the world that offered major work in petroleum engineering and petroleum geology In Europe, the first major work in petroleum engineering was offered in England in 1913 at the University of Birmingham The University of California and Stanford University offered major work in petroleum engineering in 1915 Since that time at least 10 other American universities and colleges have offered major work and at least 12 others are now offering some courses dealing with petroleum, and the petroleum industry.

Jan 1, 1935

By J. E. Russell, Y. J. Wang

In this paper, we report the results of a study of the characteristics of Texas lignite based on a proximate analysis data base previously published by the Bureau of Economic Geology, University of Texas at Austin and the U.S. Bureau of Mines. The original impetus for this study was the desire to perform a parameter study in connection with the siting of potential underground gasification tests in Texas. A numerical model of the gasification process was available and required proximate analysis data, among other parameters, as input. If proximate data were available for a particular site, a prediction of the product gas quality could be made. However, in preliminary siting studies, it would be advantageous to know what the desirable characteristics of the lignite are, in order to target general areas for drilling. Consequently, a parameter study was in order. This paper presents the methodology required to systematically vary proximate analysis parameters and estimate the corresponding energy content for various group(or formation)-facies classifications of Texas lignite.

Jan 1, 1983

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

Because common salt, sodium chloride, is necessary to all animal and much plant life, it is probably the most widely used of all mineral commodities, except for water. Nevertheless, of the total salt consumed, only 7% is used for food, including animal food. Two-thirds of the total is used as chemical raw material, principally for making such basic chemicals as chlorine, caustic soda, and soda ash. Other uses are for road thawing (16%) and water softening. Some 162.5 million tons of salt were used, worldwide, in 1972 (Table 15.4F.1). Production is from bedded salt deposits, salt domes, and evaporation of brines, including solar evaporation of seawater. Production is worldwide from at least 20 countries, of which the United States, China, USSR, the United Kingdom, and West Germany are the leaders. Consumption increases about 7 % annually. Reserves are plentiful: Other important sodium salts are soda ash (sodium carbonate) and salt cake (sodium sulfate). Soda ash comes mainly from the Solvay process (70% ) , which uses salt, limestone, and ammonia as raw materials. A large and growing portion of United States production is from mining large bedded deposits of trona, a natural hydrated sodium carbonate and bicarbonate found in Wyoming, and from brine evaporation in California. Soda ash is used for glassmaking, phenol, soap, detergents, and bleaches. Half of the United States salt cake used is a byproduct from rayon manufacturing. The other half comes from brines and playa lakes in California, Texas, and Wyoming. Salt cake is used mainly for papermaking. ACKNOWLEDGMENT Appreciation is expressed to William B. Dickson, president, Salt Institute. [ ]

Jan 1, 1976

By J. E. Lawver, J. D. Raulerson, Charles C. Cook

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent, or at least delay, mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the form of calcined bones at least 2000 years ago (Anon., 1964), and man has used phosphate minerals as a source of fertilization in one form or another for at least 100 years. During 1977 the world produced about 116 Mt of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows: marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits requiring apatite carbonate mineral separation. [ ] Guano, mostly from Chile and Peru, accounts for 0.1% of the total world production, and the calcium phosphates from Ocean, Nauru, and Christmas Islands and the aluminum and iron phosphates from Brazil and Aruba account for less than 4% of the world production and are thus not considered in this classification (Lawver, et al.). At present, marine phosphorite deposits account for about 75% of the world&apos;s production; the igneous deposits account for 20%. The igneous deposits low in carbonate minerals are easily concentrated by crushing, grinding, and apatite flotation. The most important igneous deposits are those of the Kola Peninsula, USSR (Woodrooffe, 1972). The igneous deposits high in carbonate materials are of corn appreciably more difficult to beneficiate, but they have been concentrated by froth flotation for a number of years. An interesting but rather complicated flowsheet of this type is at Phalabonva, in the Republic of South Africa (Lovell, 1976). The Phalaborwa deposit is an igneous complex of pyroxenite with a central core of carbonatite surrounded by a serpentine- magnetite-apatite rock called phoscorite. The phoscorite containing about 10% P2O5, 35% magnetite, and 35% calcium magnesium carbonate is currently being processed. The process involves comminuting the material for fiberation and subjecting it to a copper float using a potassium amyl xanthate as collector and triethoxybutane as a frother followed by a magnetic separation of the tailings to produce a feed for phosphate flotation. This process produces a phosphate concentrate containing greater than 36% P2O5 at a P2O5 recovery ranging from 75 to 80%. Considerable success has been claimed for recovering apatite from carbonate-bearing ores at the Jacupiranga Mine of Serrana S/A (Silva and Andery, 1972). The carbonatite currently being mined contains an average of only 5% P205 and is concentrated using a unique flotation process (Andery, 1968) to yield 96% P205 concentrates. The ore contains about 12% apatite, 5% magnetite, 80% calcite plus dolomite, and minor amounts of phlogopite, olivine, zircon, ilmenite, and pyrochlore. Feed preparation consists of crushing to -31.75 mm (-1 M in.), rod milling in closed circuit with hydrocyclones to about 92% (-50 mesh), and two-stage cyclone desliming of the -50 mesh sands at 20 m. Weight recovery in the deslimed feed is normally 85 to 88% and the corresponding P2O5 recovery is usually about 90%. The deslimed feed is conditioned at 60 to 70% solids for 15 min at pH = 8-10 with 0.6 kg/t of causticized starch for iron oxide and calcite-dolomite depression. The conditioned slurry is diluted to 20 to 30% solids, about 0.2 kg/t of fatty acid or soap collector is added to the conditioner discharge, and the reagentized ore is subjected to rougher-scavenger flotation with additional fatty acid added to the scavenger float. The scavenger concentrate is returned to rougher circuit distributor, and the rougher concentrate froth is subjected to two stages of cleaner flotation to yield a final apatite concentrate analyzing 36 to 38% P205. Flotation recovery of P205 is, in general, above 90% when treating fresh carbonatite. The high-carbonate flotation tails normally analyze 1 % P2O5 or less and are suitable for portland cement production. The marine deposits. Types 1 and 2 of central Florida are representative of enormous reserves of phosphate rock that will undoubtedly account for much of the world&apos;s production in the near future. Until very recently the sedimentary deposits high in carbonate minerals (Type 2) have not been considered reserves due to the difficulty in making a francolite-carbonate separation. Although no commercial plant has yet been built to beneficiate Type 2 ore, laboratory and pilot plant data indicate the process is viable. If so, the reserves of Florida and similar deposits throughout the world will be substantially increased. A discussion of the beneficiation of these two types of sedimentary deposits and the relation of the resulting concentrates to the fertilizer industry of the United States is the subject of this paper.

Jan 1, 1981

An unexpected demand having entirely exhausted the Institute&apos;s supply of the Bulletins for January and February, 1916, the sum of $0.50 each will be paid for. a limited number of copies of these Bulletins, which send to the Secretary of the Institute.

Jan 5, 1916

By A. G. Raine

For the technological age in which we live, with the constant goal of further improvement in the efficiency of mechanized systems, the need for a replacement of the antiquated drill and blast method of shaft construction has been recognized. For over a decade now; the trend in shaft construction has been toward large diameter bored shafts using either raise boring methods or more flexible, rodless "down the hole" boring machine. The limits of conventional shaft sinking have been reached, the mining regulations are more stringent, and the environmental agencies more aggressive, all contributing to the growing need for development of the rodless shaft boring machine. In the last three years in the United States, world shaft construction records have been achieved using a V-Mole machine, designed by Mirth GmbH of West Germany, using American electrics and hydraulics. Shafts of 7.0 meters (23 feet) diameter, totaling 2,255 meters (7,400 feet) in depth have been constructed at high advance rates, yet with unusually low accident rates. Bearing in mind the high cost of today&apos;s mining labor and the inherent danger associated with conventional shaft sinking, this alternative method of shaft construction achieves a fast, competitive, low manpower requirement, whilst enhancing a safer environment for the labor force. Recent results have proven that program time savings of 50 percent over conventional shaft sinking can be achieved which can be directly translated into improved client cash flow projections and more accurate project budgeting.

Jan 1, 1984

By R. C. Wilcox, R. V. Lawrence, P. A. Calhoun

The V-Rh-Si, Nb-Rh-Si, and Cr-Rh-Si systems were investigated to evaluate the extent of solid solubility between binary Cr3O structures. All Cr3O components lie within the favorable atomic size range1 for the formation of the Cr3O structure. Previous studies indicated complete solid solubility between V3Si and V3Sn2 and no solubility between Sn and cr3si3 or Si and Nb3Rh.4 The Cr3O structure is not found in the Cr-Sn and Nb-Si binary systems. Powder compacts were are-melted under argon, homogenized in a vacuum at 1000°C, and water-quenched. Alloys containing greater than 15 at. pet Si were annealed 100 hr. X-ray diffractometer methods were used to study all systems utilizing copper radiation for the Cr-Rh-Si system and chromium radiation for the other two systems. V-Rh-Si System. The alloys prepared in the V-Rh-Si system and the measured lattice parameters for the Cr3O structure found in each alloy are listed in Table I. The characteristic Cr3O diffraction pattern was found in all binary alloys. The measured lattice parameter of V3Rh (VRS-1) is in agreement with the reported value5 while the value for V3Si (VRS-5) is only in fair agreement.&apos; In

Jan 1, 1965

By Paul Soros

Terminal facilities were recently completed at Conneaut, Ohio, on Lake Erie, for the Bessemer and Erie Railroad Co. (a wholly-owned subsidiary of U.S. Steel Corp.) which may become the blue- print for all future coal shipping terminals. Design and engineering of the new facility was by Soros Associates, New York, N. Y. Unlike terminals of conventional design, for example, those at Toledo and Newport News, which load coal directly from the railroad car to the vessel, the new installation passes the coal into temporary storage, loads the vessel from temporary storage and provides alternative reclaiming systems in case of major system failure.

Jan 1, 1966

By R. S. Rickard, H. D. Peterson, M. C. Fuerstenau, J. D. Miller

The flotation characteristics of the oxide copper minerals, malachite, azurite, and cuprite, have not presented the difficulty for concentration as have those of the copper silicate, chrysocolla. The copper carbonates and oxides respond reasonably well to flotation with conventional collectors, whereas chrysocolla will not respond to flotation with fatty acids or xanthates under normal flotation conditions. In this view then, other reagents will have to be devised to function as collectors for chrysocolla. The most obvious general class of reagents for this purpose would seem to be the organic copper chelating compounds. The utility of chelating agents as collectors in flotation systems has already been demonstrated.1-6

Jan 4, 1966

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedom with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth." The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1980