Search Documents

By J. F. Myers, R. J. Tower

"There is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. General Equipment A signal light to show that a steel bin, containing relatively line, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.' TO Spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1949

By Richard S. McCaffery

A Research on iron blast-furnace slags has been in progress since 1922 in the metallurgical department of the University of Wisconsin, supplemented by observations, tests and critical examination of operating records at 10 furnaces. From the data thus collected information has been put into forms suitable for use by furnace operators and is given in this report and the three accompanying papers.' In the viscosity results reported, it is estimated that temperatures were measured within 5" C. and that the viscosity determination of the particular slag investigated is accurate within ± 4 per cent. In the viscosity diagrams in the various papers, the equal viscosity lines were drawn in such a manner that in all cases they are located correctly with respect to the actual experimental results, but when determining a viscosity for a particular composition from the diagrams, the viscosity may. be slightly less accurate than the experimentally determined viscosity for the same slag, for the reason that the iso-vis lines interpolated between the experimental results may be shifted slightly without violation of the experimental data. The viscosity diagrams represent our judgment of their position under the above conditions, and we believe the relative accuracy of viscosity data taken from the diagrams is more than sufficient for any use to which the data may be put. Hundreds of samples of slags synthetically produced in the laboratory and of actual furnace slags have been studied in various ways. The ranges of compositions of slags used for viscosity measurements are: silica 25 to 55 per cent.; alumina 0 to 35 per cent.; lime 25 to 55 per cent.; magnesia 0 to 20 per cent. These measurements were made at temperatures of 1250°, 1300°, 1350°, 1400°, 1450°, 1500°, 1550°, 1600" and 1650" Centigrade. Descriptions of apparatus, methods used and statements of the problems investigated have been published in the papers listed in the bibliography beginning on page 120.

Jan 1, 1932

By A. H. Lindley, R. Shorr, Frazier M. Stewart, F. Crerie

The mineral industry, so important to industrial development, faces a major challenge in creating the most effective financial structure to provide funds essential for seeking, evaluating, developing, and extracting minerals. The acquisition of funds for mineral development and plant erection do not differ greatly from fund-raising in nonmineral ventures because risks are essentially comparable. High-risk exploration funds, however, are more difficult for the mineral industry to acquire. With the world's ever-increasing appetite for minerals, the internally generated cash of major oil and mining companies cannot be expected solely to maintain the world's mineral supply. The augmented costs, risks, and difficulties of exploration have been shared increasingly by the smaller independent operator and by private and public participation drilling programs within the petroleum industry over the past 30 years. Only recently has the mining industry awakened to the need for utilizing exploration and development funds derived from sources other than established mining and banking circles. Almost from its inception, the oil industry was forced to drill deep holes through overburden without the aid of a mineral "outcropping" which required geological, and in subsequent years, geophysical interpretation. The poorly financed, nontechnical prospector, who depended on a mineral outcrop, was not to play an important role in oil exploration as he did in mining. Because of the high cost of drilling and the demands for technical judgment to locate an exploration drill hole, corporate and sophisticated private funds generally financed oil discoveries. When external funds were subsequently required, these financially sophisticated explorers would turn to the banking community from which came numerous ingenious innovations, taking cognizance of existing tax laws. Like the oil explorer, the miner is now faced with probing below the surface, relying solely on regional geology and geophysical anomalies. The day is gone, for practical purposes, when the prospector discovers a deposit from a mineral outcrop. There is little doubt that the mining industry will now follow the course taken by the petroleum industry in acquiring external funds if it is to meet the future raw material requirements of the world. The oil industry has been able to attract bank funds more readily than the mining industry after a mineral discovery has been made because: (1) with few exceptions, an oil discovery can be placed into commercial production and will generate cash at much less expense and time than a mine; and (2) generally, costs of oil production, the value

Jan 1, 1976

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By F. M., Waring

F. M. WARING,* Altoona, Pa.-The necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 12, 1918

By Monica Mengoli Chaves, Byron S. Gottfried

For the past several years the U. S. Department of Energy has sponsored the development of a computer simulation program that will predict the performance of coal preparation plants under a variety of different operating conditions. Recently a study was undertaken to transfer the simulation logic from the large scale mainframe environment to a small inexpensive microcomputer operating in a highly interactive "user friendly" environment. This paper describes a program that was written for the APPLE II Plus microcomputer which accomplishes these objectives. The program prompts the user for information in such a manner that it can be used by persons other than computer specialists. This makes the program directly accessible to plant managers, designers and operating engineers.

Jan 1, 1983

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection function, and a cost function. The three functions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field day available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 1, 1984

By G. R. Love

i\ program has been written which allows fully automatic conversion of data for X-ray intensity, as a function of time, to finished conventional pole figures. The program accepts input data in the serial order in which they are taken and is therefore immediately compatible with automatic data-acquisition devices. From these data taped instructions are prepared for the Calcomp plotter to construct ink-on-paper drawings. Because both Siemens and Norelco pole figure goniometers are used in this laboratory, the program was written for pole figure data obtained from one or more interpenetrating spiral scans during which both the polar angle, @, and the equatorial angle, a, are varied simultaneously and continuously. The reference direction for a scan, that is the point @ = 0 deg, may be chosen coincident with either the normal direction (N.D. figures) or the rolling direction (R.D. figures). In either case the plotted figures are drawn with the transverse direction (a = 0 deg) at the right and the rolling direction at the top. The full, circular, pole figure is drawn as two semicircular figures labeled "front side" and "back side". As presently constituted, the program will also accept data from circular scans taken at constant values of @. In every case the angular coordinates of each intensity entry are generated in the computer from a relatively small number of auxiliary data. The X-ray intensity data are corrected for background scattering by direct subtraction of the intensity measured with 28 set appropriately "off" the Bragg angle. It is possible to enter this correction as an additional spiral scan through the a, @ space; because the background correction does not normally vary rapidly enough to warrant this detailed a determination, the background corrections are entered as one or more auxiliary data. All data are normalized to a multiple of random intensity. The data taken in this laboratory for N.D. figures are normally taken in a reflection geometry from from sheet samples and do not extend beyond <p = 75 deg; for these data random intensity must be determined from separate experiments and entered as auxiliary information. When the auxiliary information is not available, a number is chosen to give intensity values normalized to a scale of 1 to 10. In this laboratory, R.D. figures are based upon hemispherical samples for which data are taken out to @ = 90 deg; for these data random intensity is calculated by direct numerical integration of . sin @ d@ using the trapezoidal rule and the background-corrected values of the input data. Points necessary to the construction of the pole figure are identified by simple linear interpolation between adjacent data points to determine the loci of contour lines. Points lying on a given contour are connected to one another with straight-line segments and the search-calculation-drawing sequence is patterned to assure that different contour lines do not cross, that a single line does not branch, and that lines do not end in space. However, so that there be no ambiguity in the data presentation, all contour lines end at the limits of the input data. Since the curves are constructed of straight-line segments, they are not continuous in their derivatives. However,

Jan 1, 1969

By F. A. Hill

Coal mining in the State of Washington offers many interesting problems for the mining engineer, due to the varied physical conditions occurring in different fields, and often in the same mine. The different coal seams worked in the same mine commonly require different mining and transportation methods for economical operation. The coal measures have inclinations ranging from 5&apos; to vertical, and in the same mine the dip of the coal may vary from 30&apos; to 50 . In all fields, the seams are extensively faulted, folded, and sheared. The quality of the coal produced ranges from brown lignite to bituminous coking coal, the following being typical analyses: Very little of the coal contains as much as 0.75 per cent. sulfur. The brown lignites occur mostly in Lewis and Thurston Counties, and as a rule are very cheaply mined. This coal has been successfully used in locomotives of the Oregon & Washington Railroad, after equipping them with specially designed fireboxes. The sub-bituminous coals occur in all the coal-mining counties. Their cost of production varies widely, according to the character of the formations, the pitch, and the wall conditions. This makes a fairly good steam coal, but the lump is used mostly for domestic trade, after grading into lump, nut, and pea. The coking coal is used for making coke, and for locomotive and other boiler fuel. It yields a strong metallurgical coke, quite high in ash, though seldom exceeding 18 per cent. ash. Most of it is susceptible to

Jan 1, 1920

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.&apos; Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder&apos;s observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,&apos; which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.&apos; Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder&apos;s observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,&apos; which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By John B. Knaebel, Robert J. Grant

This paper outlines the trends in gold production since the discovery of America, in the world as a whole, and in the principal producing regions as well. World production climbed at an average rate of about 20,000,000 oz. per 5-year period until the record all-time output of 111,307,000 oz. in the period ending with 1915. Production fell off during the war period, but has been mounting since 1925, and will probably be nearly 100,000,000 oz. for the 5-year period ending in 1930. Total world production of gold from 1492 to the end of 1930, as closely as can be determined, is more than 1,061,000,000 fine ounces. More than one-half of this total, or about 575,000,000 oz., has been mined since 1900. In percentage of world production, the United States jumped from 4.8 per cent for the decade 1831-1840 to 44.5 per cent for the five years ending with 1855. This is the highest figure ever reached by this country, although, with the exception of the 10-year period ending 1865, it ranked first among the nationa from 1849 until the end of 1905. During the 5-year period ending with that year, the United States produced 24.7 per cent of the world&apos;s gold. The tremendous increase from South Africa following 1890 resulted in that country&apos;s becoming the largest contributor for the five years 1906-1910, a position it has held with increasing dominance ever since. Relegated to second place in the period 1906 to 1910, the United States produced nearly 20 per cent of the world&apos;s new gold until 1920. From 1921 to 1925 it averaged 13.6 per cent and since then it has continued to decline in relative importance, accounting for only 10.9 per cent in 1927. Final figures for 1930 may place Canada second among the gold producers of the world.

Jan 1, 1931

By Sultan Amerie

PERSIA looms up more prominently each year as one of the richest oilfields in the world. The actual production in the south and the possibilities in both the north and the south are very great. The output in the south, where the Anglo-Persian Oil Co. operates a wide concession, is steadily increasing, the returns for the fiscal year 1922-23 being 2,957,028 tons. The estimated production for. 1923-24 is 3,775,000 tons. The figures for the past few years have been as follows: 1918-19 1,106,415 tons 1920-21 1,743,557 tons 1919-20 1,385,301 tons 1921-22 2,327,221 tons According to the company&apos;s last annual report, the production from the -Persian fields operated by its subsidiaries has been well maintained and is now being increased to deal with the expanding off-take of the company&apos;s refineries at Abadan, Persia, and Dandarcy, Wales. Test drilling in an entirely different area in Persia indicates the existence of a new oilfield, which it is intended for the time being to hold as a reserve.

Jan 3, 1924

By Wilford S. Wright

FOR the past four years the management of the Black Hawk Consolidated Mines plant at Mogollon has conscientiously kept accurate records pertaining to cost of operation and the performance of certain equipment. These records have been valuable in coordinating the work in the mine, mill and power plant. Also, as to quantity and kind of equipment and supplies most suitable from the standpoint of economy and dependable operation, they have served as a guide. Through comparison with records at other mines, where the same things are being done in a different way, they have pointed out mistakes to be avoided. No outstanding accomplishments, either in costs or performances, are revealed; in fact, some of the results are perhaps quite inferior to those obtained at similar plants, but it is with the thought that more records should be published for the benefit of the mining profession that the author presents these data. To other operators and to mining engineers who are called upon to make estimates for prospective operations, the information herein should be helpful. GENERAL CONDITIONS Mogollon is in the southern part of Catron County, southwestern New Mexico. It lies near the western border of the Mogollon Range, 14 miles east of the Arizona line. Silver City, 80 miles to the southeast, is the nearest railroad point. The connecting road, over which supplies are hauled into camp by trucks, is an improved highway for about 50 miles; the remainder consists of graveled roads and unimproved steep mountain grades. One general supply truck and one tank truck make daily round trips. Hauling of supplies to the mine has cost at the rate of $0.08 per ton-mile; or, on the basis of ore production, $0.30 per ton mined. Lumber, hauled in from local mills, has cost an average of $30.00 per 1000 board feet, $8.50 of which has been for hauling. The annual consumption averages 108,000 board feet. Lime, hauled from a plant in Arizona, is about the only other item not brought out from Silver City. Fuel oil for the generation of power is the item of greatest hauling expense, the f.o.b. Mogollon cost of approximately $0.06 per gal. being nearly twice the f.o.b. refinery price. Water for power plant, mill and camp use flows to camp storage tanks through a 4-in. pipe line from a spring and intake 3 miles up Silver Creek Canyon. A few times, particularly in the month of June, mill operations have been suspended for two or three days because of water shortage. MINING CONDITIONS During the years 1938, 1939, 1940 and 1941, the mine produced 230,059 dry tons

Jan 1, 1943

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.&apos;, n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " &apos;.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.&apos;,&apos; Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a&apos;=-n;s/= nD,(qo);"; and b&apos; = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

By AIME AIME

The Bulletin. As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the Institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will be: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. A supplementary session of this meeting will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the further discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. The XCVIIth meeting will be held on the Pacific Coast, including a visit to the Exposition at Seattle, and various other points en route going or coming, depending upon the route and program finally adopted. More definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Feb 1, 1909

TO metallurgists generally, Arthur S. Dwight is no stranger even to those who do not know him personally. He is one of those contributors to technical progress whose names will go down to posterity because of their being attached to a successful machine or process, such as Dorr, Hardinge, or Marcy, or Wedge, MacDougall, or Herreshoff. The roasting and sintering method and equipment developed by Colonel Dwight and his associate, the late Richard L. Lloyd, may be found in lead smelters throughout the world, and also in many metallurgical works dealing with other ores, including those of iron. It is ordinarily used to desulphurize and agglomerate fine ores for subsequent smelting. Colonel Dwight&apos;s citation as James Douglas Medalist reads: "For his contributions to the art of smelting nonferrous ores; and particularly for his pioneer work in developing equipment and technique for sintering such ores and metallurgical products." The medal was awarded at the last Annual Meeting of the A.I.M.E. but unfortunately the medalist was unable to leave Florida at the time to receive it in person.

Jan 1, 1942

By D. W. Fuerstenau, G. D. Gumtz

Use of the discretized batch-grinding model for the simulation of locked-cycle grinding tests from batch-grinding data is illustrated. The simulated results were compared with actual locked-cycle experimental data for the dry grinding of dolomite. To illustrate the utility of this simulation method, a number of relationships between operating and performance parameters were generated, including relations between batch grinding and the Bond test, the production rate and the circulating load, and the production rate and the product size. A large amount of testing is done each year in the mineral industry for use with grinding unit cperations, and much of the experimental test data is obtained by the tedious locked-cycle testing procedure. In addition to being experimentally complex and requiring large amounts of sample, the very nature of the locked-cycle experiment yields results that cannot readily be interpreted. The attempts that have been made to model comminution systems during the last few years may provide a better and simpler way to obtain and analyze grinding test data; these models involve elements of both fitting to "model equations" and deterministic representations.1-1 The traditional engineering design techniques for comminution systems have relied mainly upon large amounts of industrial operating data that have been correlated with locked-cycle grinding data.&apos;,&apos; Bond&apos;s empirical mill-design procedure involving locked cycle testing remains the most generally available method to this day. The purpose of the present paper is to show how much more useful data can be obtained from a simple batch-grinding experiment that provides information which subsequently can be utilized with population balance models of the grinding process to simulate locked-cycle behavior. These simulation results can, of course, be used in Bond&apos;s general design scheme. However, the combination of batch-grinding tests and the population balance model allows many more conditions to be considered than do single laboratory tests under specific locked-cycle conditions. The use of these simulation techniques for prediction of locked-cycle behavior represents one of the first practical applications for the simulation method in comminution.

Jan 1, 1971

By K. Nassau

The Effect of tin and hydrogen on the C0 parameter of a titanium. specimens were capsule cooled in water to eliminate contamination by water. Deybe-Scherrer photograms were obtained in a 114.6 mm camera with CuKa radiation. The parameters shown in Table I and Fig. 1 were calculated from the 213 (8569°) and 302 (8173.5°) reflections? no attempt being made to correct for systematic errors. The principal difference in method of preparation of specimens between this investigation and that of Worner was the use of pickling by the latter to produce X-ray diffraction samples. The possibility that hydrogen introduced by pickling was responsible for the lower a and c-parameters was investigated with the same 80 pct HNO3- 20 pct HF solutions used by Worner. The 6 and 10 at. pct specimens, the parameters of which had already been determined, were pickled and the c-parameters obtained are also shown in Fig. 1. The a-parameters, not shown, are also diminished. The quality of the lines obtained from the unetched and etched samples was unchanged, being quite sharp in both cases. It is quite possible that if corrections for systematic error carried out that the parameters obtained for the unetched samples would approach the data of Worner. In any event, the parameters of the etched samples would be still lower. The data obtained here is evidence that hydrogen in solution has contracted the c and a -parameters. Crystallographic Angles of Calcium Tung-state (Tetragonal, c/a = 2.169) K. Nassau In connection with the preparation and orientation of single crystals of calcium tungstate (Scheelite -CaWO4), the need arose for a stereographic projection for this tetragonal material. There appear to be no tetragonal projections with a c/a ratio above that of indium1 (c/a = 1.522) in the literature. In addition to its use for calcium tungstate, such a projection might find other more general applications and is accordingly presented below. The most recent X-ray diffraction work on CaWO4 is that of Swanson, Gilfrich, and Cook,2 where a summary of previous work is also found. Lattice parameters given are: a = 5.242A, c = 11.372A, and c/a = 2.169. The material is tetragonal with space group Table I, giving angles between crystallographic planes (HKL) and (hkl), was calculated from the formula3

Jan 1, 1961

By Lyall Zickrick

EXPERIMENTS of previous investigations have indicated that calcium-copper alloy, when used as a deoxidizer for molten copper, results in a sound copper casting of good physical and electrical properties. Bradenberg and Wiens1 have obtained successful results in casting sound copper using calcium for deoxidizing. Masing2 has obtained deoxidized copper of high density and high conductivity by use of calcium. Pratt,3 in 1907, patented the use of calcium for the deoxidation and degasification of, copper. Schumacher, Ellis and Eckel 4 in 1929, conducted a series of experiments on deoxidizing copper with calcium. They concluded that so long as there is only a small percentage of residual calcium the mechanical and electrical properties of the copper deoxidized are not impaired; and the deoxidation is thorough. For this investigation, a, copper-calcium alloy high in calcium and 10 variously deoxidized copper ingots were prepared. The investigation concerns itself with the casting properties and structure of these variously deoxidized ingots, their working and annealing characteristics, and the resulting physical and electrical properties of the worked materials.

Jan 1, 1932