Search Documents

By G. H. Rowe, A. N. Stroh, D. P. Gregory

The magnitude and variation with strain of the parameters activation volume, V*; activation energy, H; and frequency factor, A, in the Arrhenius equation for strain rate are determined for colunlbium single crystals and polycrgstals. Comparison of dislocation structures in deformed columbium crystals as determined by transmission electron microscopy with the rate IF deformation of a metal crystal is a thermally activated process, rate theory can be used as a powerful tool in the study of dislocation mechanisms. seeger1 develops the following expression for plastic deformation governed by a single thermally-activated theory results suggests thai formation of lattice vacancies at jogs in screw dislocations is responsible for thermally activated deformation of poly crystalline columbium. Single crystals appear to deform by a different mechanism. Work hardening in fully recrystallized fine grain columbium is found to result from simultaneous decrease in activation volume and in the number of mobile dislocations with increasing strain. Work hardening in recovered polycrystals is found to result from decrease in activation volume with strain only. dislocation mechanism. His equation for strain rate is where N is the number of mobile dislocations per unit volume held up at energy barriers, v is the frequency with which the dislocations "try" the energy barriers, b is the Burgers vector, a is the area a dislocation loop sweeps out after overcoming a barrier, V* is the activation volume which will be defined more completely later, and t* is the thermal component of stress equal to (Ta-Ti), where Ta is applied shear stress and Ti is internal stress of the dislocation network17' given by

Jan 1, 1963

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction'-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By Spencer S. Shannon

The lanthanide elements from lanthanum (atomic number 57) to lutetium (71) plus yttrium (39) are called the rare-earth elements; scandium (21) is chemically similar to yttrium and the lanthanides, but differs in occurrence. The rare-earth metals were divided into three categories by the chemist, Berzelius, in the early 1800s; however, modern usage defines only two groups. The cerium group is named after the most abundant -element and comprises lanthanum (57), cerium (58), praseodymium (59), neodymium (60), promethium (61), samarium (62), europium (63), and gadolinium (64). Traces of natural promethium were discovered in apatite in Finland (Erametsa, 1965). The yttrium group, also named after its most abundant representative, comprises terbium (65), dysprosium (66), holmium (67), erbium (68), thulium (69), ytterbium (70), and lutetium (71). Yttrium most closely resembles holmium in chemical properties, and occurs most commonly with the heavy lanthanides. The rare-earth minerals may be divided into cerium-group, yttrium-group, or mixed-group classes. A number of rare-earth minerals contain thorium and uranium, but these are variable in content and are not essential to the composition of the minerals. In monazite, a mineral that is a principal source of rare earths, the worldwide average content of thorium oxide is 7.2 % ; however, varieties of monazite contain as little as 0.001% and as much as 31.5% thoria. Monazite is the chief ore of thorium and, until recently, thorium has been the main product; the rare-earth metals were in fact byproducts. However, because of the great demand for rare-earth metals by the petroleum refining and the iron and steel industries since the early 1970s, the roles have been reversed so that thorium is now the byproduct. Uses A 9 to 1 mixture of yttrium and thorium oxides is used for high-intensity incandescent lamps and for high-temperature-resistant windows and lenses. Yttrium oxysulfide and orthovanadate, doped with europium oxide, are used in color television tube phosphors. Yttrium, as well as cerium, praseodymium, and samarium, is alloyed with cobalt to form strong permanent magnets. It hardens magnesium alloys and retards the oxidation of iron-chromium alloys. Yttrium-iron garnets are used for transmitting low microwave frequencies. Yttrium-aluminum garnets are used as host crystals for lasers and as artificial gems. Yttria also forms strong, stable, high-temperature refractories. Gadolinium-gallium garnets are used in substrate wafers on which bubble-memory films are deposited. Rare-earth chlorides, particularly of lanthanum, neodymium, and praseodymium, are used as catalysts for petroleum cracking. Mischmetal is used for lighter flints and to improve the ductility and impact strength of iron and steel alloys. Mischmetal also reduces the fatigue resistance of magnesium and aluminum alloys. Rare-earth oxides are used for polishing glasses and lenses. Individual or specific combinations of high-purity oxides are used as additives in glass to maintain or change its color, dispersion, or refractive index. High-purity oxide combinations are also used to color tile and to opacify porcelain enamel. Rare-earth fluorides and oxides are used in carbon-arc electrodes to provide incandescent white light. Lanthanum or gadolinium oxysulfide phosphors, activated with terbium, are used as x-ray screen intensifiers. Hydrogen can be stored by sorption on lanthanum-nickel alloys (Anon., 1979). Thorium232 is bombarded with slow neutrons in breeder reactors to create fissionable thorium233 for nuclear fuel cells. The 330-MW, high-temperature gas-cooled reactor at Fort St.

Jan 1, 1983

By F. F. Poland

S. ROLLE*—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By R. N. Singh, A. S. Atkins

One of the most difficult problems associated with modern mechanised longwall mining is the lack of system flexibility to deal with local changes in geology, seam thickness and the face design parameters. As a consequence of system rigidity and the quest for increasing the coal face performance, the percentage extraction in the U.K. is currently below 52%. The paper outlines the current guidelines used in face design which permit coal to be left in situ for various purposes and discusses the strata control implications in extracting subsequent panels in the same and adjacent coal seams. The paper examines the application of strata mechanics to the design of longwall layouts for maximizing .the percentage of coal extraction. Remedial measures include optimizing pillar dimensions, reduction in roof coal left for support purposes by improving the use of available powered support technology and application of thick seam mining methods including sub-level caving and techniques of extracting coal from odd shaped pillars. Case studies are described where coal extraction has been maximized by adopting a new single heading retreat mining system; a shallow seam partial extraction system utilizing, existing heading machines and minimisin8 coal sterilization in pillars by replacing longwall access roadways by goaf scour.

Jan 1, 1984

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 ft and diameters of over 30 in., have become numerous and widespread. 50 such holes have been drilled for access shafts to LPG mined caverns. Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-in. diam with 1600-ft depths, 120- in. diam with 570-ft depths, and 72-in. diam with 4800-ft depths. Equipment is now available to drill a wide range of big holes for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of big holes. The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The purpose of this paper is to present a review of the big hole drilling equipment available, a compilation of the available data on large-diameter holes, to show the experience obtained to date and to show that big hole drilling is feasible and available to the industry.

Jan 12, 1965

By Walter A. English, Ralph Arnold

Though production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a fairly liberal policy toward the prospector, which should stimulate wild-catting, although the province of British Columbia, which controls public lands within t.hat province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 1, 1923

By Walter A. English, Ralph Arnold

Though production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a fairly liberal policy toward the prospector, which should stimulate wild-catting, although the province of British Columbia, which controls public lands within t.hat province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 1, 1923

By Ralph Arnold

THOUGH production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a .fairly liberal policy toward the prospector, which should stimulate wildcatting; although the province of British Columbia, which controls public lands within that province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 7, 1922

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By Charles T. Van Winkle

Until the advent of the porphyry coppers and the introduction of flotation which soon followed, crushing and grinding for many years proceeded along somewhat stereotyped lines, without important alteration in type of machinery. For the finer crushing and grinding, stamps, rolls, and various patterns of Huntington and Chilean mills were in general use. Ball-mills were in use abroad, but owing to their small capacity and the high cost of screens and steel, they never obtained much footing in the United States. Tube-mills were first introduced into the crushing departments of cyanide plants when it was found that for crushing finer than 30-mesh other types of crushing machinery were not efficient. In order to crush with one pass, these mills were made 18 to 22 ft. (5.5 to 6.7 m.) in length. Pebbles were used as a grinding medium and the mills were lined with either silex blocks or fragments of quartz or flint pebbles set in cement. While the cylindrical tube pebble-mill had been used to some extent in small installations of concentration mills, the first instance of its use on a large scale was at the concentrating plant of the Miami Copper Co., where 8-ft. by 22-in. (2.5-m. by 55.9-cm.) Hardinge mills were tried out against Chileans. The results of these experiments led to the gradual replacement of the Chilean by the Hardinge mill. Robert Franke published an article' describing the work done, comparing the two types of mills. At the same time, according to Franke, a test was run using a 6-ft. (1.8-m.) Hardinge ball-mill as a substitute for rolls for intermediate crushing on 1/2-in. material. According to Franke, this mill was soon discarded, since it was found that to obtain the desired product the mill must be limited in capacity. The Miami Copper Co. made no test with other types of ball- or pebble-mills. Following this example, others installed the conical type; and when the Inspiration Consolidated Copper Co. decided to build a concentrator, it adopted the conical mill. As the requirements for mills would be very large, it purchased manufacturing rights in the State of Arizona from the

Jan 1, 1918

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931

By AIME AIME

THE statements quoted below range widely over the field of contact between education and industry. 'Their sources are as indicated. True Education "Education must escape from its traditional warped and narrow views as to what constitutes life and preparation for life. It must train young men and women for vigorous, wholesome development of every important element of personality. It must build physical and mental health. For each student it must inform and discipline thinking in literature, in physical, bio- logical and social sciences, and in philosophy. It must awaken appreciation of beauty.

Jan 1, 1929

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Table I (Jones, 1973) affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 (Anon., 1967) is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak-type brines, produced mainly for lithium. Market Attributes Some of the important market traits common to industrial minerals used by the chemical industry are listed below. 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. For example, fluorspar from China and Thailand normally goes to Japan, while South African fluorspar can go either to Japan or to the US. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities.

Jan 1, 1983

By J. H. Wernick, E. E. Thomas

THE etch-pit technique for revealing dislocations in bulk samples allows one to determine dislocation densities and to study their behavior under various mechanical and thermal treatments. We have developed a chemical polish-etch for the development of etch pits on the (1100) plane of Cd which appear to

Jan 1, 1961

By A. Stumpf, Y. Berube

An experimental apparatus for studying the aqueous oxidation of sulfide minerals is presented. The oxidation kinetics for molybdenite in solutions of caustic soda and dissolved oxygen are discussed; results of leaching experiments on chalcopyrite concentrates are given. Preliminary results on the transfer of oxygen into water are also discussed.

Jan 1, 1974

By M. A. Mahtab, J. D. Dixon

The results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block- caving method are presented. The two-dimensional finite-element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1977

By L. Dudley Stamp

In my last report on Petroleum in Burma and India1, details were given of production and development up to 1932. It was pointed nut, that the only statements available for Burma were those published officially by' the Government of India in the Annual Review of the Mineral Production of India (Records of the Geological Survey of India), which are issued about 10 or 11 months after the close of the year. Operations in Burma are almost entirely in the hands of three companies—the Burmah Oil Co., the British Burmah Petroleum Co. (with its subsidiary, the Rangoon Oil Co.) and the Indo-Burma Petroleum Co.—and these companies preserve a policy of secrecy, so that details are not available of new wells, depth, wells abandoned, or of other figures, except in so far as the Government considers it advisable to publish the information in its possession. GeneRal Developments in 1933-1934 As predicted in 1933, there have been no spectacular developments and no new fields have been discovered. Nor are there any new indications of a likelihood of fresh discoveries. The policy of extremely careful exploitation. has been continued and intensified; production is being maintained at an almost steady level and can be so maintained for many years to come—indeed, it is the policy of the leading company to permit refinery and local market requirements to dictate the production required. Contrary to experience in practically every other part of the world, India has shown a slightly decreased demand for petroleum products—especially kerosene, but also for gasoline. The increased use of electricity would explain the lower demand for kerosene, but the falling off in the demand for gasolinc can only be attributed, according to the Chairman of the Burmah Oil Co., to the depression and to the incidence of heavy taxation. In India (including Burma) as a whole, production was 305,018,751 Imperial gallons in 1931 (8,714,822 U. S. barrels); 308,606,031 Imp. gal. in 1932; 306,009,022 in 1933 and is estimated at 308,000,000 in 1934.

Jan 1, 1935

By Edmund Kirby

This meeting marks the point at which the long-standing dissatisfaction with the mineral-land laves, the innumerable protests against them, and the many isolated efforts to obtain relief, have developed into a general movement for the: revision. That part of the mining industry which is affected by these laws has three general organizations to speak for it: the American Institute of Mining Engineers, Mining and Metallurgical Society of America, and the American "A Mining Congress: all of which are represented in this meeting. In the series of able and thoughtful presented here, prominent men have discussed the evils of the present laws aid some of the reforms which should be made in them. We all appreciate fully the ultimate value of these studies; but we are also painfully aware of the fact that discussion of this kind has been going on for a quarter of a century without any other effect than a steady increase in the mass of printed records stored on library shelves. In order to get any practical result we must induce an indifferent government at Washington to act, and to do this we must unite in pushing some practical plan whereby it may act in a simple and effective way and with the least possible amount of criticism or opposition. The actual question before us is not whether the mining laws are bad; for their evils and absurdities are not only beyond discussion but also beyond the resources of a temperate and dignified vocabulary. It is not what particular changes ought to be made; for it is premature to make specific recommendations until there is some one to listen to them. Moreover, we all know that there are wisdom and experience enough available, and awaiting that time, for the creation of a code which would be a model to the mining world. The practical question now is, how to obtain the revision; and since the American Mining Congress has of late restricted its attention to this phase of the problem I wish as one of its representatives here to present its views upon the matter.

Jan 6, 1914