Search Documents

By Theron Wasson

During 1936 the state of Michigan produced 11,868,573 bbl. This is approximately 4,000,000 bbl. less than produced in 1935. The principle reason for the decrease in production over the previous year was the rapid decline of the Crystal field, which reached its peak in October 1935. The old producing area—Mt. Pleasant, Porter, Yost-Clark— accounted for over 7,000,000 bbl. during 1936. Crystal produced a total of 2,400,000. Outstanding among the old fields were Vernon and

Jan 1, 1937

By J. W. Still

CIRCULAR steel sets have proved to be more economical for supporting slusher drifts in the block-caving mining used by the Miami Copper Co., at Miami, Ariz. The first steel sets were installed in July 1950, and up to July 1, 1951, about 474 sets (approximately 1896 ft of drift) were placed; the bulk of this work was done in the latter six months. All of the places selected for the steel were in heavy ground. Based on this experience the following definite conclusions can be drawn:

Jan 11, 1951

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: mass transfer to a region near the surface, adhesion onto a partially filled surface, and resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. Results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1985

By R. E. Old

THROUGH the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-balance methods and the equations for natural water encroachment to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed.

Jan 1, 1942

By N. Albon, J. F. Miller, R. W. Coutant

The deposition of nickel from nickel carbonyl onto amorphous substrates has been studied, with attention being paid to the specific effects of the physical and chemical nature of the substrate and to the effect of oxygen on the crystal morphology. With substrates having microscratches or etch lines, nu-cleation was observed to occur preferentially at these surface features. Flame polishing of the substrate surfaces was found to remove any regularity in preferred nucleation sites. Nucleation was observed to occur less readily on substrates having relatively low surface energies, e.g., Teflon and carbon, than on materials having relatively high surface energies such as fused silica. At low oxygen concentrations [Ni(CO)4/O2 > 54 x 1031, apparently pure and well-formed nickel crystals were observed to nucleate and grow irrespective of the presence of oxygen. At higher concentrations of oxygen, a secondary growth process, dependent upon oxygen concentration and resulting in a gradual change in crystal morphology, was observed. It is concluded that the influence of oxygen on the nucleation and growth of nickel is determined by the relative kinetics of the various possible reactions, and that under the experimental conditions employed the 0-Ni interaction occurs at some nucleation or prenuclea-tion stage. THE purpose of the research on crystal nucleation in chemical vapor deposition as described in this paper has been twofold: 1) to examine some effects arising from the use of amorphous substrates, and 2) to study the specific effects of oxygen on the nucleation and growth of nickel in a nickel carbonyl-carbon monoxide system. The nickel-nickel carbonyl system was chosen for study for several reasons: 1) nickel films are of potential interest in electronic technology, and 2) the deposition can be carried out at moderate temperatures, thus making possible detailed study of the processes occurring and the use of a variety of substrate materials (including some which melt at relatively low temperatures). Fairly well-characterized chemical kinetics and a broad background of information are available on the py-rolysis reactions and on the mechanisms of Ni-O interactions. NUCLEATION AND GROWTH THEORY The theoretical background for the analysis of nucleation and growth by vapor deposition for a one-component system (physical vapor deposition) and the problems encountered therein have been reviewed by Hirth and pound.' More recently Mande12 has indicated the difficulties of applying such theory to chemical systems. One of the major problems involved is the possible multiplicity of chemical reactions and deposition routes. For example, those reactions which are probably of significance in a discussion of the pyrolytic deposition of nickel from nickel carbonyl under the conditions of the present experimental work are illustrated in Fig. 1. As is true with most cases of chemical deposition, many of the quantitative data necessary for a complete analysis of the system are either not available or not directly measurable. However, with the present system, sufficient data are available for a discussion of nucleation and growth on a qualitative basis. Classically, the rate of nucleation of a monatomic species being deposited from a vapor phase is given by

Jan 1, 1965

By W. G. Wender

The North Central Texas district, as known to the oil fraternity, is the area producing from sands and limes of Pennsylvanian age, roughly embracing the territory lying between Fort Worth and Abilene in an east-west line, and between the Red River and the Llano Mountains in a north-south line. The history of oil development in North Central Texas during the year 1927 is briefly reviewed in the following paragraphs. Brown County New discoveries and development in Brown County centered mainly around the Fry pool, located in the west central portion of the county. Important discoveries for the year were: Shoupe No. 1 John Byler, discovery well of the Byler pool, located 2 miles south of the Fry pool which camc in early in February, 1927, at 1262 ft. for 90 bbl. in the Fry sand of upper Strawn (Pennsylvanian) age. Rosenfield No. 1 P. Davis, discovery well of the Smith-Ellis pool located 1 1/2 miles northeast of the Fry pool, came in March 7, in the Fry sand from 1277 to 1279 ft. for 30 bbl. initial. Pandem Oil Corpn. No. 1 Mrs. T. Hutton, located 1 mile east of the Smith-Ellis pool, came in in December in the Fry sand from 1119 to 1130 ft. for 45 barrels. The Fry pool passed its daily production peak of 25,000 bbl. during the first part of June, and declined to a daily production of 5100 hhl. by the close of the year. The oil recovery from the Fry pool up to Jan. 1, 1928, slightly exceeded 4,000,000 bbl., averaging 4700 bbl. to the acre. over the entire pool. The Smith-Ellis pool passed its daily production peak of 5300 bbl. in Octohcr, 1927, and dropped to 3600 bbl. by the close of the year. The possibilities of the Byler pool will be unknown until the area is fully drilled up. In the Blake pool, production passed 2,500,-000 bbl. for the year. The per acre recovery in this pool up to lkc. 31, averaged slightly over 5000 barrels.

Jan 1, 1928

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By P. R. PaeIay, A. Slibar

Using three-dimensional, stress-deformation rate equations for a Bingham plastic, an approximate solution for the laminar flow of drilling mud between the drill pipe and casing is given for the case when the velocity gradients due to axial flow are large compared to velocity gradients due to rotation. INTRODUCTION The fact that drilling mud can be treated, to a first approximation, as a Bingham plastic has been established by several investigators12,3,4,5. A Bingham plastic is a material that is rigid until a certain combination of stresses exceeds a critical value. When the stresses are sufficiently high to initiate flow, the reduced stresses have a constant ratio to the corresponding deformation rates at each point. Prediction of pressure and torque requirements to produce the desired flow of the material have been made by analytical solutions due to Bingham6, Reiner7, and Buckingham8. One part of the present means of calculation that requires clarification is the flow between the drill pipe and casing. Present methods treat the flow resulting from the rotation of the drill pipe separate from the flow produced by the axial pressure gradient. Since the non-linear behavior of a Bingham plastic implies that solutions cannot be superposed, the present analytical investigation was undertaken to obtain a solution to the problem of combined axial and tangential flow. Equations have been proposed for the three-dimensional flow of a Bingham plastic9,10,11 and it has been shown that the proposed equations lead to the usual solutions from the one-dimensional theory". Applying these equations to the flow between two concentric cylinders the problem of axial flow only13 and tangential flow only12 have been solved. In addition to the separate problems of axial and tangential flow between concentric cylinders, the authors have determined the relationship between external torque on the inside cylinder and axial pressure gradient necessary to initiate flow". The solution given in Ref. 14 points out the complexity of the present problem. The problem considered here is the case of simultaneous axial and tangential flow. The axial flow, necessary to keep the drill bit free of removed material, results from the axial pressure gradient. Tangential flow is present since the drill pipe rotates in the hole. The solution given here is valid when the shear stresses in the drilling mud due to rotation are small compared to the shear stresses resulting from the axial flow. This case for laminar flow can be encountered in oilfield drilling. STRESS-DEFORMATION RATE EQUATIONS A detailed derivation of the equations governing the behavior of a Bingham plastic is given in Ref. 10. This section briefly outlines the physical reasoning leading to this three-dimensional formulation of the stress-deforma-tion rate law. Experiments on a certain class of materials have demonstrated the following properties: (1) when a certain combination of the stresses is below a critical value no deformation of the material occurs, (2) to a first approximation this combination of stresses is independent of the hydrostatic pressure (negative average normal stress), (3) if flow occurs the ratio of the reduced stress to the corresponding deformation rate is constant at each point of the flowing material, and (4) incom-pressibility. For the one dimensional case of shear deformation, Bingham6 formulated the governing equation as dxx, = 0 for sxx < to and µdxx = s xx = to for sxx to , . where dxx is the shear deformation rate, sxx the shear stress, to the critical shear stress, and p the slope of the sxx vs dxx curve for dxx > 0. Fig. 1 shows the behavior for pure shear between two parallel plates. Taking into account the physical properties given above and assuming the critical combination of stresses to be measured by the octahedral shear stress, the fol-lowing three-dimensional equations have been proposed.

Jan 1, 1958

By W. Rall, A. J. Birkle

The effect of fast-neutron irradiation on the micvo strcture of a common reactor pressure-vessel steel, A212 Grade B, was studied using thin-foil transmission electron microscopy. The dislocation density of the irradiated material is considerably greater than that of the nonirradiated control material. Annealing studies indicated that dislocations and hardness ill the irradiated material annealed out—as docs the radiation-induced embrittlement according to other- investigators— at temperatures STEELS in nuclear reactors are affected by neutron irradiation. In the American Society for Testing Materials (ASTM) A302B and A212B steels commonly specified by designers for reactor vessels, between 650° and 800°F. However, the dislocations and hardness in control samples cold-worked to 9 and 70 pct did not anneal out readily, and a high dis -location density was observed, even after a 1-hr anneal at 850°F. Based on the hypothesis that cllrster defects, rather than the increased dislocation density, are primarily responsible for mdicltiotz-iudziced e)nbriftlen7ent, reconzmendations are made for reducing the susceptibility to such ernbrittlement. exposures at a temperature of 550°F or lower to neutron dosages encountered during a 20- to 30-year life (-3 X 10&apos;&apos; nvt, >1 mev) may increase the nil-ductility transition temperature (NDT) as much as 300" or 400".&apos;9 Therefore, to prevent brittle failures in reactor structures, extreme caution is required to reduce thermally induced stresses during all reactor shutdowns and startups when the temperature is below the NDT of the pressure vessel.

Jan 1, 1964

By John W. Vanderwilt

THE fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence- are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore.

Jan 1, 1946

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean&apos;s equation (Eq. [4] of Gifkins&apos; paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean&apos;s equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"&apos; on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins&apos; work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins&apos; results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins&apos; results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author&apos;s reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By J. P. Lesley

The old do not love to see the young pass away from the light of the sun before them. Fathers would fain keep their sons by their side to the. end of life ; but the old Greeks, who loved the old gods, were wont to moderate their grief with the sweet superstition that only those whom their gods especially loved died early. The Christian church found consolation in that superstition applied in a new form to its new sorrows, and paid its most enthusiastic devotion to the memories of its young and beautiful martyrs. The natural science of our century is robbing us fast of this and all other superstitions, sweet as well as bitter, and leaving us for consolation to the teaching—colder, yet kinder—of personal fortitude and that optimism Which intelligently translates the Cosmos of Humboldt back into its old name of the Harmonia of Pythagoras. The Homeric Kataclothes, the three fates, are dead and gone for us, with that old world which comprehended none of the laws of cause and effect, and sorrowed for those who were cut off from the land of the living without hope of more than a shadowy existence beyond the river of death. All the more the ancients cherished the memory of their dead and lavished their choicest art upon their monuments. We moderns have lost the monumental arts, but we better keep the monuments which our dead leave behind them. No one of us who has done good work can fail to be remembered; and in an Institute like this, which keeps the press at work, an immortality in the memory of men is more possible, more certain, for every one of its members than the greatest heroes of antiquity could anticipate for themselves. In old apocalyptic times the works of men followed them through death to the throne of God to be their advocates in judgment, but in these modern times our works remain this side the grave, to follow the name of the departed one as it takes its course along the history of his peculiar art or science advancing slowly to perfection. We write the epitaph, not upon the mouldering stone of a tomb, but on the pages

Jan 1, 1890

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By Donald L. Katz

The compressing of gas into a partially depleted gas drive oil reservoir to bring the contents to a single phase miscible with gas is proposed as a process worthy of serious study. The compressed gas and vaporized oil would be recovered by cycling. This paper explores the Possibility of recovering oil from reservoirs of 6,000 ft or more by this method. INTRODUCTION Many new methods for increasing the recovery of oil from reservoirs are under consideration in the various research laboratories. One method which should be considered for recovering oil From partially depleted gas drive fields is to compress gas into the reservoir until the contents become a single phase miscible with more gas. Natural gas then may be cycled through the reservoir to recover the oil. This procedure ideally will eliminate the capillary effects of the liquid ill the porous media and should permit recoveries similar to those obtained in cycling operations, probably of the order of 80 per cent. This paper explores the information now available for the prediction of the performance of such a project and discusses the problems likely to be encountered in recovering oil by cycling. For many years dry natural gas has been passed through oil reservoirs to recover natural gasoline which would vaporize from the oil. Recently a process of recovering more of the high boiling hydrocarbons has been described by employing high pressures at which the heavier hydrocarbons have a higher volatility. Nevertheless. this reported method does not eliminate the differential nature of the vaporization process and capillary forces are still present in the reservoir. The process under discussion in this paper would minimize differential vaporization and would remove capillary forces which are responsible for low oil recoveries. Higher gas pressures are required to accomplish this removal of the miniscus, but it does not follow that more gas is required for oil recovery. The process is limited to reservoirs deep enough to permit the use of the required pressure — Probabably 6,000 it and deeper. DESCRIPTION OF THE PROCESS Briefly, the process is to compress natural gas into an oil reservoir which is partially depleted so that it has an oil saturation in the range of 40 to 60 per cent of the hydrocarbon pore space. The injected gas will pass through the channels formerly carrying gas to the wells to build up the pressure and dissolve in the oil phase. This injection will continue without production from the field until the reservoir reaches a single phase. If one were to select unique conditions such that the gas composition, the reservoir oil composition and the Per cent saturation would bring the mixture in the reservoir to the critical temperature and pressure simultaneously the phase behavior accompanying injection is shown by Fig. 1. The oil-gas mixture in the depleted reservoir has a critical temperature at C,. Addition of natural gas to the mixture will give a new critical temperature for each addition. Mixture No. 3 is shown to have its critical temperature at the reservoir temperature and reservoir pressure at P: the critical pressure. Under ideal behavior, the entire reservoir would be at iti critical temperature and pressure and the entire hydrocarbon content would be at a single phase. If the reservoir content were a binary system of methane and a heavy constituent. it would be miscible with more methane. However, for complex mixtures the critical locus does not confine the two phase region, and the dew point curves of Fig. 1 occur above the critical locus. If fluid which was injected into the rezervoir at the critical point were of the

Jan 1, 1952

By J. C. Savins

The practical analysis of the hydrodynamics of the wellbore has long been a subject of interest to engineers. This paper presents a simplified solution to the problem of computing the pressure drop for the flow of drilling mud in the annulus of the wellbore. This solution is, however, an exact and rigorous solution under the assumptions which have been imposed. These assumptions are that the drilling fluid is a Bingham plastic fluid* and that the annulus is formed by two concentric, stationary, cylindrical pipes. It is further assumed that the fluid is incompressible and that its motion is isothermal and in a steady state. This problem under the same assumptions has been attacked by previous authors. Beck, Nuss and Dunn&apos; proposed that the equation for the flow of a Bingham plastic fluid in a cylindrical pipe could be applied to an annulus if the pipe radius were replaced in the equation by the hydraulic radius. This equation, known as the Buckingham-Reiner equation&apos; (see Appendix 1), was also used in an approximate form. Van Olphen pointed out that even for a simple or Newtonian- fluid the pipe equation (Poiseuille&apos;s law) could not be converted to the Lamb equation escriptive of flow in an annulus (see Appendix 1) by using the hydraulic radius. Van Olphen further attempted to give a solution for the annular flow of a Bingham plastic fluid by introducing approximations similar to those which have been used in the case of the Buckingham-Reiner equation. Other attempts to provide approximate or exact solutions have been made by Grodde&apos; and by Mori and Ototakeq. The present authors some years ago in unpublished work derived the correct expressions relating the pressure drop and flow rate for this problem. It was found that the solution consisted of two simultaneous equations, one of which contained a logarithmic term. Thus, obtaining numerical results for any particular case of interest involves very tedious trial-and-error computations. Very recently Laird presented the correct derivation of the two equations which are given in full detail in Appendix 1. In order to reduce the amount of calculation time which would be involved in providing a complete tabular or graphical solution to the problem, a high-speed electronic digital computer has been utilized. For this purpose the two simultaneous equations were transformed into more compact expressions by introducing reduced variables. These expressions are given in the following theoretical section. A similar procedure in this problem has been developed by Fredrickson and Bird1" Their tabular results, however, are very incomplete in the range of practical interest for problems of wellbore hydrodynamics. We have furthermore been able to express our graphical results in terms of convenient and familiar dimensionless groups. THEORETICAL DEVELOPMENT Use of Reduced Variables In terms of reduced variables the two simultaneous equations just discussed take the following form, The reduced variables q, x, a and z are defined in terms of the various measured quantities, where Q is volumetric flow rate, AP/L is pressure gradient, Dl is OD of inner pipe, D, is ID of outer pipe, is plastic viscosity, and is yield point. Thus, we have a dimensionless volume flux, a dimensionless reciprocal pressure gradient, and the ratio of the pipe diameters Before introducing the fourth reduced variable, z, it is of interest to consider the physical significance of the parameter x. As may &apos;be seen from the velocity profile of Fig. 1 the Bingham plastic fluid has the interesting property that a portion of the stream flows at a uniform velocity without shearing action. This section of the stream is situated approximately in the center of the conduit and is known as the "plug flow" region. Its existence is due to the fact that the shearing stresses within the region do not exceed the yield point, which is one of the two flow properties characterizing the fluid. The parameter x then turns out to be the ratio of the

By R. Maddin, S. K. Tung

SUCCESS of the dislocation theory in formulating the transitional lattice theory proposed by Har-greaves and Hill in 1929&apos; is well established for low angle grain boundaries. The theoretical work of Burgersa and Read and Shockley,3 together with the experimental observations of Aust and Chalmers4 and Parker and colleagues,6 leaves little doubt as to the structure of grain boundaries with differences of orientations up to between 15" and 20". Beyond these angles, the structure of the boundary is not so clear, and is still a matter for conjecture. There have been notable experiments devised from which the data could be used to calculate energetics for possible arrangements of atoms in forming a large angle boundary.6 Most of these experiments deal with diffusion through and along the grain boundary. The recent work of Rhines and Cochart7 and Rhines, Bond, and Kissel18 was concerned with the relative movement of grains in aluminum bicrystals under constant tensile loads with their boundaries aligned at 45 " to the tension axis. The gliding along the grain boundary was cyclic and began after an incubation period. The velocity of gliding increased with the sum of the angular difference, 8, between the operative slip direction in the conjugate crystals and the angular difference between the active slip planes as measured between their traces upon the grain boundary. The initial gliding rate varied with temperature, and the logarithm of the average gliding taken over a considerable period was a linear function of the reciprocal of the absolute temperature: the slope gave an activation energy of 11,000 ±1,000 cal per mole. Since the rate of grain boundary shear is sensitive to the misorientation of the grains themselves, as shown by several workers,7,8 it is suggested that further work of this type might be fruitful in adding information regarding the behavior of boundaries under stress. The techniques devised by Chalmers" added impetus to the facility for observing grain boundary behavior, in that they provided a simple means for producing bicrystals of predetermined orientation so that the angle of the boundary could be controlled,

Jan 1, 1958

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918