Search Documents

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By Norman Gerald

THE lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnec-essary drilling.1 While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a tech-nique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By I. A. Ettlinger

THE formation that the writer has chosen to call "The Central Arizona Batholith" is included in the Globe, Miami, Ray, Pioneer, Troy, and Silver King mining districts. Its extension to the southeast is in the Banner mining field. Basing his argument on what is known of batholithic intrusions, the author offers reasons for considering all these granitic outcrops as parts of a single great mass of plutonic rock. The United States Geological Survey has subdivided this area into three -quadrangles-the Globe, the Ray, and the Florence. Of the first two, geologic atlases1 have been published, but of the last, the topographic map alone is available. These mining districts include such prominent present-day producers as Inspiration, Miami, Old Dominion, Arizona Commercial, Iron Cap, Superior and Boston, Magma, Belmont, and Ray Consolidated. Among those well known in the past are Silver King mine and Gibson mine. Fig. 1 is a geologic map of the Central Arizona Batholith region. F. L. Ransome's excellent work on The Copper Deposits of Ray and Miami, Arizona,' is of great value to all workers in those districts. His geologic map for the Ray and Globe quadrangles has been incorporated in Fig. 1, and the stratigraphic names employed are those first applied and defined by him in his pioneer work in this region. The purpose of this paper is to show that the ores are related to post-Carboniferous granitic intrusions; that while there does not seem to be any adequate explanation for the distribution of all the igneous stocks, a preexisting structure does appear responsible for at least the location of the largest igneous stock of the region; that the principal producing vein mines are located in the sedimentary rocks in the roof of this batholith, while the disseminated copper deposits are found bordering the lower portions of the batholith exposed by erosion; that primary zoning is illustrated not only on a broad (district) scale but also on a small (individual

Jan 1, 1928

Since the beginning of the 20th century the world has been trying to find a new political system, even as it did at the end of the 18th century. The French Revolution instigated the destruction of absolute monarchies when Napoleon unwittingly showed the masses the advantages of freedom, as opposed to the abuses of unlimited power by the imperialists. In spite of advances in culture, science, and technology during the past 50 years, there is a hangover of laissez-faire economic principles. Failure to divert the trends of minority pressure groups has caused two world wars and is the basis for the current social unrest and turmoil. In the ebullition of ideas there have risen to the surface the dregs of ideas, old and new-Nazism, Fascism, Russian Communism-a hodgepodge of imperialistic, socialistic, communistic and capitalistic maneuverings where state monopoly of capital enables ruthless exploitation of the masses. The United States owes much of its industrial greatness to the work of pioneers in the mineral industries. The task of the pioneer was to locate and develop in a rude way the mineral resources of the nation. Today, mineral industries leaders are still in great demand, but for a different purpose-to direct intelligent utilization of the limited, waning, submarginal mineral resources. Today the need is for trained earth scientists, mineral

Jan 1, 1950

By J. N. Hummel

THE methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view, The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic.

Jan 1, 1931

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956

By Warren B. Weeks

The development of the relatively deeper fields discovered during 1937 helped build the 1938 production to 18,456,760 bbl., an increase of 6,295,910 bbl., or 51.6 per cent over 1937, and the largest production for south Arkansas since 1930. Schuler and Rodessa accounted for the increased production as well as for over half of the wells drilled in the state. There were 243 holes drilled during 1938, of which 200 were completed as oil or gas wells. Of the 29 wildcat wells completed, 25 were dry, 3 found oil in the Smack-over limestone, while 1 made a small oil well in the Nacatoch sand. This was less than half the number of wildcats drilled the previous year, but nearly twice as many field wells were drilled. The old depth record of 7973 ft. was exceeded twice during the year, with the present record of 8332 feet. Trend of Prospecting The porous "Reynolds" oolite of the Smackover limestone1 has been the object of most of the wildcat prospecting during the past two years. Seismograph work, which brought 22 crews into this area during 1938, was largely pointed toward a study of the structure of this limestone formation. Thirteen dry wildcats have been drilled to this formation and five pools have been opened in it since it was first found to be productive at Snow Hill in the spring of 1936. With the failure of "updip" prospects to produce, activity moved southward and basinward. Success in five instances in Columbia and south Union Counties has spurred activity in this area. Much of the acreage is under lease and half a dozen deep limestone tests are assured for the current year. Fig. 1 shows the location of the principal oil fields in south Arkansas, as well as one or two minor producing areas. The fields are numbered in the order of their discovery. It is shown that most of the recent discoveries are from the deeper formations. Dry wildcats that penetrated

Jan 1, 1939

By Warren B. Weeks

The development of the relatively deeper fields discovered during 1937 helped build the 1938 production to 18,456,760 bbl., an increase of 6,295,910 bbl., or 51.6 per cent over 1937, and the largest production for south Arkansas since 1930. Schuler and Rodessa accounted for the increased production as well as for over half of the wells drilled in the state. There were 243 holes drilled during 1938, of which 200 were completed as oil or gas wells. Of the 29 wildcat wells completed, 25 were dry, 3 found oil in the Smack-over limestone, while 1 made a small oil well in the Nacatoch sand. This was less than half the number of wildcats drilled the previous year, but nearly twice as many field wells were drilled. The old depth record of 7973 ft. was exceeded twice during the year, with the present record of 8332 feet. Trend of Prospecting The porous "Reynolds" oolite of the Smackover limestone1 has been the object of most of the wildcat prospecting during the past two years. Seismograph work, which brought 22 crews into this area during 1938, was largely pointed toward a study of the structure of this limestone formation. Thirteen dry wildcats have been drilled to this formation and five pools have been opened in it since it was first found to be productive at Snow Hill in the spring of 1936. With the failure of "updip" prospects to produce, activity moved southward and basinward. Success in five instances in Columbia and south Union Counties has spurred activity in this area. Much of the acreage is under lease and half a dozen deep limestone tests are assured for the current year. Fig. 1 shows the location of the principal oil fields in south Arkansas, as well as one or two minor producing areas. The fields are numbered in the order of their discovery. It is shown that most of the recent discoveries are from the deeper formations. Dry wildcats that penetrated

Jan 1, 1939

By W. M. Weigel

The rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers —the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used in its natural state after mechanical preparation only (such as grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the Eastern and Northern Statcs. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The Southern States have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the North, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries, for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business revives and freight rates are adjusted. Most of the non-metallic mines are small and the tonnage handled is low in comparison with the tonnage involved in modern large-scale mining of coal, iron, copper, etc. On the other hand, at nearly all non-metallic

Jan 1, 1923

By W. M. Weigel

The rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers —the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used in its natural state after mechanical preparation only (such as grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the Eastern and Northern Statcs. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The Southern States have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the North, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries, for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business revives and freight rates are adjusted. Most of the non-metallic mines are small and the tonnage handled is low in comparison with the tonnage involved in modern large-scale mining of coal, iron, copper, etc. On the other hand, at nearly all non-metallic

Jan 1, 1923

By Leo Behr

RECENT years have seen important practical advances in the construction of recording instruments for use with thermocouples. The difficulties of the problem will be appreciated when it is remembered that a 10° F. change in temperature of a base-metal couple at 1500° means a change in the electromotive force of about 0.00035 volt. In a circuit having a resistance of 350 ohms, this means a change in the current of 0.00000,1 amp.; and despite this requirement of great sensitivity the instruments must be sufficiently robust to withstand the rough usage which is so often their lot. Two methods are in common use for the measurement of the electromotive force produced by a thermocouple: 1. The milliammeter method, in which the current produced by the thermocouple in a circuit of known resistance is measured and from. this the electromotive force is deduced by Ohm's law. 2. The potentiometer method in which a known potential difference is opposed to the thermocouple electromotive force. The use of thermocouple and milliammeter for measuring temperature introduces some possible sources of error, for the reading depends on a number of factors, including the following: (1) Electromotive force set up at the hot junction, (2) electromotive force set up at the cold junction, (3) resistance of the circuit including thermocouple, lead wires, and meter, (4) field strength of magnets, (5) strength of controlling springs in meter, (6) friction at pivots, of pointer on paper, etc. It is obviously necessary to so design and maintain the installation that the reading is independent of all the factors except the first. The electromotive force set up at the cold junction can easily be taken care of provided it is constant. This has been approximately accomplished by burying the cold junction in the ground or actually secured by locating it in a container, the temperature of which is kept constant by means of a thermostat.

Jan 9, 1919

Very few data are available about production in this county. The amount mined was used locally, or shipped by river, until 1839 when the canal was completed to Dunnsburg. Only partial records for four years remain of canal shipments. Considerable coal was used locally by the iron works at Farrandsville for some years. Rail shipments started in 1861 and those shown are the estimated shipments of these mines as compared with the mines in other counties served by the Philadelphia and Erie Railroad, the total tonnages being given in the annual reports to the Auditor General. It is not likely that any coal used by the railroad is included in these figures. (Table 40.)

Jan 1, 1942

By P. J. Conners, H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of moving bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at the same speed and without impact, then about 90% of all belt conveyor problems would disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. Some general design criteria required for proper transfer of materials from one conveyor to another are established and discussed. Specific attention is given to loading chutes and skirting.

Jan 1, 1973

The Anglovaal Group has released details concerning its new processes for recovering platinum group metals, stating that the Group's system, which involves batch processing and precipitation methods for these metals (PGM's), leads to faster recovery times, increased recoveries, and higher purities than the conventional process. Insofar as South Africa's Merensky Reef is concerned, the Anglovaal method of recovering palladium first (as opposed to platinum in the conventional process) enables it to use a much simpler process in the subsequent recovery of platinum and other metals. Because the processes give cleaner separations, the volume of material to be recirculated -and therefore the total volume of material in the recovery circuits- is reduced substantially.

Jan 3, 1976

By M. R. Geer

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built.

Jan 7, 1953

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

By W. F. Hosford

A series of aluminum single crystals was subjected to axially symmetric flow by drawing through dies. The orientation dependence of the drawing stress, which indicates the resistance to this type of flow, compares reasonably with predictions of Taylor and of Bishop and Hill. Measured lattice rotations likewise are generally consistent with theory. The most successful analyses of the plastic behavior of polycrystalline metal and its relationship to single crystal behavior are those of Taylor1-3 and of Bishop and Hill.4-6 The purpose of this paper is to provide a critical test of some of the basic assumptions involved in these theories. Both treatments apply to fcc metals and assume the shape change of each grain in a polycrystal to be the same as that of the polycrystal as a whole. Thus for a randomly oriented polycrystal extended under uni-axial tension each grain is assumed to undergo axially symmetric flow. dey = dez = -1/2dex, deyZ = dezx = dexy = 0 [l] where x, y, and z are a set of orthogonal axes, x being the tensile axis. Although [011.] oriented grains in bcc and fcc metals may depart markedly from this ideal behavior,7,8 the assumption is probably quite reasonable for most grains. Under a uniaxial tensile stress, ox, the work dW per unit volume expended in producing an increment of axial strain dex is, dW=oxdex [21 Since this work is expended in slip, dw =STi dyi 131 where Ti and yi are the shear stress and shear strain on the active slip systems. In both analyses Ti is taken to be the same on all slip systems, and dependent only on the total prior shear strain on all systems, so dw = Tdy [41 where t is the shear stress required for slip and y is the sum of the shear strain yi on all slip systems. Combining 121 and [4] and defining M = oX/T The ratio M is a generalized Schmid factor. It relates the tensile stress required for axially symmetric flow, ox, to the basic shear stress, 7, and it also expresses the ratio of crystallographic strain, y, to the tensile strain, Ex It depends only on the orientation of the crystal. Taylor evaluated M for various orientations by finding the least value of dy/dEx which could satisfy the shape change. Bishop and Hill, on the other hand, found M by considering the relative work (1/T)dW/dEx expended by stress states which could activate enough slip systems to produce the shape changes. The results of both methods appear to be equivalent, although certain omissions were made in Taylor's original work. The orientation dependence of M, calculated by the second method,9 is shown in Fig. 1. Taylor used the average 2= 3.06 for all possible orientations to predict the tensile stress-strain curve (oxvs Ex) for a random polycrystal from the shear stress-strain curve (t vs y) of a single crystal. Changes in M from lattice rotation were neglected so points on the ox vs ex curve were simply taken at ox = 3.06t and e = y/3.06 from corresponding points on the t vs y curve. Recent extension of the analyses of Taylor and of Bishop and Hill to crystallographically textured metals has been used to relate plastic anisotropy to textures, and to predict the potential texture hardening that could result from texture control.9 Unfortunately there have been relatively few experimental tests of the underlying theory. Taylor found that the tensile stress-strain curve of polycrystalline aluminum did agree reasonably well with that predicted from a single-crystal T-y curve. Had the single crystal undergone easy glide, how-

Jan 1, 1965