Search Documents

By B. D. Lichter

The lattice parameters of zirconium and zirconium-oxygen solid solutions (hcp) were determined from measurements of back-reflection X-ray photograms obtained at 29°C using a symmetrical focussing camera. The following linear equations between parameters (c,a) in angstrom units (10-8 cm) and atom ratio (m) of oxygen to zirconium were obtained: c = 5.14764 + 0.2077m a =3.23168 + 0.1099m. The linear equations given are valid over the range 0 to 5 at. Pct 0. The accuracy of individual parameter measurements approaches the limiting accuracy determined by the spectral broadening of the incident characteristic radiation, and exceeds the accuracy of previously reported values. THE present work was undertaken in order to determine the lattice parameters of zirconium-oxygen solid solutions with an accuracy that allows quantitative determination of oxygen in zirconium. The results indicate that this is possible if very careful measurements are made, since the parameter change is only a few hundredths of a percent per at. pct 0.1, 2 In the present investigation the desired accuracy was achieved with large-grained samples using a back-reflection focussing camera and maintaining good temperature control during exposure. In addition a digital computer was used for calculation of the parameters by means of an analytical extrapolation.37 Suitable diffraction photograms were obtained from large-grained samples by using a modification of the technique described by Graf and Monteil.5 This consists of simultaneous rotation and oscillation of the specimen about two mutually perpendicular axes during exposure. Whereas, normally the upper limit of grain size is about 50 µ for useable diffraction photograms, this technique allows extending the upper limit of grain-size to exposure of a single crystal. EXPERIMENTAL Preparation of Alloys for X-ray Diffraction—Zir-conium, designated as hafnium-free, Westinghouse "Grade 1," was swaged from l/2-in.-diam crystal bar to 3/8-in.-diam rods. Substantially all of the hydrogen was removed from the zirconium by annealing at 1200°C in a high dynamic vacuum. The rods were then swaged to 0.2 in. diam without intermediate annealing, and 2 in. lengths were cut for alloying with oxygen. Samples for chemical analysis were taken from portions of the rods between each 2 in. length. Chemical analysis of the dehydroge-nated zirconium is given in Table I. Commercial tank oxygen (99.5 pct 0) was condensed in a liquid nitrogen-cooled trap, and part of the condensate was slowly reevaporated into 5-liter storage flasks. Nitrogen remained as a reactive impurity, and the calculated maximum increase in nitrogen content after a 5 at. pct 0 addition to zirconium was 50 ppm by weight. However, chemical analyses of several of the prepared alloys indicated that the maximum increase in nitrogen content was 10 ppm. The storage flasks, a Sieverts-type gas burette and manometer, and associated traps, pumps, and pressure gauges were connected through a glass high-vacuum manifold to comprise the gas addition system. A fused silica tube, connected to the mani-

Jan 1, 1961

By Lester Uren

The fluid level maintained in wells pumped for oil is an important factor in deter-mining their productivity but one that has received little attention in the literature relating to petroleum-production technology. In the present paper the writer undertakes to show how and to what extent fluid level influences productivity and suggests the use of a fluid level indicator as an aid to the oil producer in maintaining the fluid surface within the well at the proper position. IT is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended, should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the .ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size, of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well.. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 2, 1925

By L. D. Clark, S. S. Saluja

A physical law, governing the rupture of rock by confined explosive charge correspondent to current expressions for determining weight of charge to rupture rock burden, W, was developed in the form Q = cVw3 by two early investigators performing unique experiments with ice. The coefficient C, is found by trial blast. Recent physical tests conducted with rock, synthetic materials and ice to establish the validity of the theory on which it and other related formulae are based indicated: (a) that failure under hydrodynamic impact pressure is by tension rather than shear as was assumed; (b) that the fundamental law of mechanics, enabling the determination of Q = cvw3, modified to the form P = R x Sa x Wb is valid when low velocity explosives are used; (c) that rock breakage under the action of low velocity explosives is entirely due to explosion gas pressure, as was believed; (d) that under the action of high velocity explosive it is due to the joint effects of scabbing and gas pressure; and that further possible modification could make the above equation also applicable to these joint mechanisms. shape could be easily frozen and because large loads would not be required. They found: (a) that the not unfamiliar shearing equation for metals was applicable to ice where P = load in lb; S = periphery of pressure surface, in.; W = burden, in.; K = modulus of rupture by shear in lb per in.2; and (b) that "the form of cavity produced by the application of gradual pressure is similar to that obtained by blasting in rock under similar conditions of free face and pressure surface!" This similarity in crater shapes leads to the conclusion that rock would rupture by shear, as did ice, and its behavior under the force of a blast could be governed by such a relationship as P = S x W x K. Three important interrelated empirical expressions were derived and rock, charging and spacing coefficients C,, C, and e were established and substantiated by trial blasts. In checking the accuracy of the main assumptions, duplication of the ice tests, substituting rock, suggested that K is not constant and that P = K x W x S, though valid for ice, does not necessarily hold for homogeneous limestone.' Conclusions from this later work raised questions making continued investigation desirable because such conclusions do not destroy the practical value of the empirical equations or theory. Further study for the establishment of the relationship between load, burden and periphery of the pressure surface and possible application of these to the mechanism of rock blasting was undertaken by the authors of this paper. MECHANICAL TESTING - EXPERIMENTAL PROCEDURE Certain inconsistencies in the results of the aforementioned tests repeated on three types of limestone suggested these inconsistencies be attributed to rock inhomogeneity. It was also suspected that the loading speed, which could not be held uniform, may have contributed. The earlier work with both rock and ice

Jan 1, 1964

By Edward Salisbury Dana

THE remarkable advance in the Science of Mineralogy, during the years that have elapsed since this Text-Book was first issued in 1877, has made it necessary, in the preparation of a new edition, to rewrite the whole as well as to add much new matter and many new illustrations. The work being designed chiefly to meet the wants of class or private instruction, this object has at once determined the choice of topics discussed, the order and fullness of treatment and the method of presentation. In the chapter on. Crystallography, the different types of crystal forms are described under the now accepted thirty-two groups classed according to their symmetry. The names given to these groups are based, so far as possible, upon the characteristic form of each, and are intended also to suggest the terms formerly applied in accordance with the principles of hemihedrism. The order adopted is that which alone seems suited to the demands of the elementary student, the special and mathematically simple groups of the isometric system being described first. Especial prominence is given to the "normal group" under the successive systems, that is, to the group which is relatively of most common occurrence and which shows the highest degree of symmetry. The methods of Miller are followed as regards the indices of the different forms and the mathematical calculations. In the chapters on Physical and Chemical Mineralogy, the plan of the former edition is retained of presenting somewhat fully the elementary prin¬ciples of the science upon which the mineral characters depend; this is par¬ticularly true in the department of Optics. The effort has been made to give the student the means of becoming practically familiar with all the modern methods of investigation now commonly applied. Especial attention is, therefore, given to the optical properties of crystals as revealed by the micro¬scope. Further, frequent references are introduced to important papers on the different subjects discussed, in order to direct the student's attention to the original literature. The Descriptive part of the volume is essentially an abridgment of the Sixth Edition of Dana's System of Mineralogy, prepared by the author (1892). To this work (and future Appendices) the student is, therefore, referred for fuller descriptions of the crystallographic and optical properties of species, for analyses, lists of localities, etc.; also for the authorities for data here quoted. In certain directions, however, the work has been expanded when the interests

Jan 1, 1922

Here, published for the first time, is the group of Anaconda officials (New York office) concerned with the planning and operations of the company's copper properties in Chile.

Jan 1, 1952

By Arch J. Alexander

This paper is a resume of a study undertaken by the West Virginia Department of Mines. The underlying and direct causes of accidents are determined in each occupational group. Then from this study, accident prevention courses, visual and written, are to be taken to the various working groups in the mines. THE causes of accidents in West Virginia mines follow the main pattern of coal industry accidents in the United States—falls of roof, ribs and face, 56 pct; from haulage, 25 to 30 pet; blasting, 3 pet; electrocutions, 3 pct; explosions, 2 pct; and other causes, about 10 pct. To arrive at some satisfactory conclusions regarding causes and prevention of mine accidents, the Department of Mines has made a study of all mine accidents, from 1945 to 1948, inclusive. During the last two years of this period, we did not have a major explosion, one that took the lives of as many as five men. The direct cause of these accidents is apparent in the reports but we who are making a close study into their frequency think that the virus lies much deeper, and we want to suggest an underlying cause. The rapid growth of the coal industry in West Virginia, the largest producer of bituminous coal, has resulted in a demand for manpower which probably has never been equaled in mining history. At the turn of the century, West Virginia had 24,635 men employed in and about her mines, and they produced 21,153,341 tons of coal a year. In 1948, there were 125,669 men employed, and coal production for the year was 168,589,033 tons, an average increase of 35 pct for each year since 1900. Over 100,000,000 tons of this increase were mined in the southern counties of the state. A safety analyst might read into the history of this development an underlying cause for accident occurrence. He might say that in such a vast, rapid development the available supply of trained miners became exhausted and that young, inexperienced men were employed in the mines by the thousands. Being unacquainted with the hazards of mining, it would be only natural for these young men to be injured or killed in too great a number. This assumption would not be borne out by the records. Men were not injured or killed in disproportionate numbers during their first years in a mine. The only reason we can give is that, during these years, they possessed an attribute of safety—CAUTION—to a much greater degree than in the years following. The coal companies in West Virginia that have been operating over a number of years have a nucleus of employees who have been with them ten, twenty, thirty, and forty years; many of them having gained all of their mining experience with one company. Their habits of work have been

Jan 1, 1951

By Arch J. Alexander

This paper is a resume of a study undertaken by the West Virginia Department of Mines. The underlying and direct causes of accidents are determined in each occupational group. Then from this study, accident prevention courses, visual and written, are to be taken to the various working groups in the mines. THE causes of accidents in West Virginia mines follow the main pattern of coal industry accidents in the United States—falls of roof, ribs and face, 56 pct; from haulage, 25 to 30 pet; blasting, 3 pet; electrocutions, 3 pct; explosions, 2 pct; and other causes, about 10 pct. To arrive at some satisfactory conclusions regarding causes and prevention of mine accidents, the Department of Mines has made a study of all mine accidents, from 1945 to 1948, inclusive. During the last two years of this period, we did not have a major explosion, one that took the lives of as many as five men. The direct cause of these accidents is apparent in the reports but we who are making a close study into their frequency think that the virus lies much deeper, and we want to suggest an underlying cause. The rapid growth of the coal industry in West Virginia, the largest producer of bituminous coal, has resulted in a demand for manpower which probably has never been equaled in mining history. At the turn of the century, West Virginia had 24,635 men employed in and about her mines, and they produced 21,153,341 tons of coal a year. In 1948, there were 125,669 men employed, and coal production for the year was 168,589,033 tons, an average increase of 35 pct for each year since 1900. Over 100,000,000 tons of this increase were mined in the southern counties of the state. A safety analyst might read into the history of this development an underlying cause for accident occurrence. He might say that in such a vast, rapid development the available supply of trained miners became exhausted and that young, inexperienced men were employed in the mines by the thousands. Being unacquainted with the hazards of mining, it would be only natural for these young men to be injured or killed in too great a number. This assumption would not be borne out by the records. Men were not injured or killed in disproportionate numbers during their first years in a mine. The only reason we can give is that, during these years, they possessed an attribute of safety—CAUTION—to a much greater degree than in the years following. The coal companies in West Virginia that have been operating over a number of years have a nucleus of employees who have been with them ten, twenty, thirty, and forty years; many of them having gained all of their mining experience with one company. Their habits of work have been

Jan 1, 1951

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By Edgar Schweitzer

The original Dorrance breaker of the Lehigh Valley Coal Co. was erected in 1883. The coal beds were clean and dry, consequently a dry preparation system was used, consisting of revolving cylindrical screens for sizing and hand-picking, to remove the few impurities from the run of mine coal. The picking or cleaning room contained long parallel rows of chutes with seats mounted on them, for the use of the breaker boy, who bent over the chute and picked out the refuse material from the coal as it gravitated down the chute. The introduction of dry mechanical pickers, of, the sliding frictional type, in the early nineties lessened the number of boys, but hand-cleaning on the coal and refuse discharge ends of the mechanical picker was necessary. The Pardee spiral pickers, which were brought out about 1900, were better than the gravity pickers and gradually replaced them. In 1912 the breaker was entirely remodeled, although the original frame was retained. The revolving screens were replaced by shaking screens, and Pardee spirals were installed on all sizes of coal from egg to pea coal, inclusive. Hand-picking still was necessary on the coal and refuse ends of the spirals, although the changes did result in a reduction of the former breaker force. As mining advanced, and the thick clean bed became exhausted, it was necessary to mine veins containing a high percentage of impurities, which complicated the preparation problem. The most serious difficulty was the increase in the quantity of damp or wet run of mine, which could not be fully cleaned on the spirals. When this quantity exceeded approximately 5 per cent. of the feed, it was necessary to send the excess of the wet coal to the company's Prospect colliery for wet washing. This plan worked well for a time, but as the amount approached 15 per cent., with the prospect of a further increase, the company considered the building of a wet-washing plant. The Dorrance breaker was the only dry-cleaning plant operated by the company. At the seventeen other collieries, wet washing was employed, and jigs, both plunger and pan, were used. All the practical methods used in the anthracite fields were investigated, and it was finally decided to adopt the Rheolaveur system. The decision was due largely to the experience gained from the the operation of a Rheo-

Jan 1, 1931

By S. Stutz

Three years ago, at the Philadelphia meeting, in February, 1881, the author had the pleasure of presenting to the Institute a paper on coal-washing machinery.* Since that time many new machines, with important improvements and labor-saving apparatus, have been introduced, the construction and description of which may be of interest to some of the members of the Institute. By referring to the above-mentioned paper, and more especially to Plate IV., representing a vertical section of a coal-washer, it will be noticed that the bottom of the plunger-box B is made level or horizontal, and supports a spring-buffer F for the purpose of limiting the down-stroke of the plunger P and receiving the impacts of the latter. Althongh the construction of the box, in view of these impacts, received from the start the proper attention (the bottom of the chamber 3 being made of three thicknesses of 3-inch planks, resting on 6-inch sqnare columns), yet, through careless working of the machinery, without the necessary water in the box, it proved in several instances not strong enough, and had to be changed. To prevent such interruptions in future, it became necessary to devise some means for relieving the machine from the impacts of the plunger altogether. This has been accomplished by the arrangement shown upon Plate I. of this paper, representing a new waesher; and not only has the difficulty been overcome, but also sorne other advantages have been obtained, as will be seen further on. The compartments +, A' of the separator-box have been set upon heavy cast-iron brackets B, leaving sufficient space below the bottom for the buffer F and the sediment-valve K. By means of the plunger-rod 6 passing through the stuffing-box s to the outside, and provided at its lower end with a shoe a, the impacts of the plunger are now transmitted from the buffer F directly to the foundation. At the same time a better guide for the plunger P in its up and down movement has been obtained. The plunger of the former machine had only the guide I and the yoke Y, whereas the new machine has an additional guide in the stuffing-box s, thus preventing wear and friction of the plunger against the lining of the box. Further-

Jan 1, 1884

By C. Norman Cochran, James L. Brandt

ALTHOUGH gas in aluminum and its effect on aluminum products have been the subject of a number of papers, not many quantitative determinations of the hydrogen content of solid aluminum and its alloys have been recorded in the literature. For solid aluminum samples, four investigators have reported hydrogen contents which appear reasonable compared with the hydrogen solubility of 0.7 ml per 100 g, STP, in molten aluminum at 660°C established by Ransley and Neufeld' and verified by Opie and Grant' and Ransley and Talbot. Sloman," who used a vacuum fusion procedure, reported the hydrogen content of some high purity aluminum as 0.66 ml per 100 g, STP. Griffith and Mallett, employing the tin fusion method, reported the internal hydrogen content of six different aluminum alloys as ranging from less than 0.1 ml per 100 g, STP, for 1100 alloy to 0.7 ml per 100 g, STP, for 4043 alloy (previously 43S, a 5 pct Si alloy). Eborall and Ransley," using a solid extraction of the gases at 600°C, reported hydrogen contents ranging from 0.1 ml per 100 g, STP, to 1 ml per 100 g, STP. Ransley and Talbot reported that several thousand analyses on 99.2 pct and higher purity aluminum as well as Duralumin type alloys indicated hydrogen contents ranging from 0.1 ml per 100 g, STP, to 0.5 ml per 100 g, STP.

Jan 1, 1957

By J. S. Browning

The U.S. Bureau of Mines has been experimenting with flotation processes to separate the spodumene-beryl ores mined at Kings Mountain, N.C. The success to date as well as the present status of the process is discussed. Further experimentation is underway and studies will be made on the milling costs involved in the flotation process. The pegmatites of the Kings Mountain-Lincoln ton, N.C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li,O(lithia) as spodurnene.' The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,-000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2-7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals. Several years ago, the U.S. Bureau of Mines, recognizing the need for developing a large domestic supply of strategic beryl, undertook studies to develop improved methods of recovering this mineral. Because of the low beryl content of the pegmatites, economic production of the beryl entails its recovery as a byproduct of spodumene flotation. Thus, the development of procedures that would provide for maximum recoveries of the spodumene, as well as the beryl, was a primary objective of the studies. Tests were made on run-of-mine ore and spodumene flotation tailing from the Foote Mineral Co.'s spodumene concentrator at Kings Mountain (Fig. 1). Pet-rographic analyses of the ore and flotation tailing are given in Table I. Detailed analyses and examinations of the ore and tailings revealed that the beryllium was present in the form of a low-alkali beryl. The crystals were small, rarely larger than 14-mesh diam, and were clear and colorless. About 10 pct of the Li20 content of the ore was present in the mica and feldspar components of the pegmatite. In some weathered ores the associated clays also contained small amounts of lithia. This is typical of pegmatites in the Kings Mountain area. LABORATORY TESTS In the past, a vigorous chemical treatment of the spodumene surfaces with acid or caustic soda has been considered essential for satisfactory selective flotation of the spodumene from the other minerals in pegmatites. Many tests were made during this investigation to determine if chemical treatment of the spodumene could be eliminated in favor of a reagent combination that would depress the other minerals while selectively floating the spodumene. A simple reagent combination and process was developed that gave better spodumene recovery and grade of concentrate than the more elaborate acid or caustic treatment methods previously used. The finely ground ore pulps were conditioned with either an ammonium, alkali, or alkaline earth lignin sulfonate and sodium fluoride, and the spodumene was floated and cleaned using oleic acid as the collector. The spodumene tailing was deslimed, conditioned with sulfuric acid and coco amine acetate, and floated to reject mica. The mica tailing was thickened and conditioned with hydrofluoric acid, then washed to remove the acid. The washed pulp was conditioned with sodium hydroxide for pH control, and the beryl was floated and cleaned with oleic acid as the collector. Table II summarizes the results of the laboratory test work. About 77 pct of the spodumene and 75 pct of the beryl were recovered from the pegmatitic material. The spodumene concentrate assayed 6.1 pct Li20 and 0.01 pct BeO, and the beryl product assayed 3.0 pct Li20 and 1.57 pct BeO. Similar results were ob-

Jan 1, 1961

The visitors to the October meeting will be given opportunity to visit the coal fields in Illinois, adjacent to St. Louis, the steam-shovel operations near Pittsburgh, Kan., and the Oklahoma oil fields. The coal mines of Illinois, Missouri, Kansas, Oklahoma and Arkansas furnish fuel over all of the central region of the country. Especially at this time, this district is of importance because of the necessity of producing enormous quantities to meet the country's demand. Some of the mines produce as much as 5,500 tons in 8 hr., and. the total output of Illinois, alone, in 1916, was 63,000,000 tons. Visitors may see elaborate underground electric tram systems, large underground machine repair shops, surface plants equipped for rapid loading, and some of the most modern coal-washing installations. The conditions for mining here are somewhat simpler than in the east.

Jan 8, 1917

By V. D. Leary, O&apos

Contracts between The Anaconda Co. and its miners at Butte, Mont., are not contracts in the true sense of the word. They are weekly verbal agreements which tacitly admit that the company, on the one hand, will supply the place, the tools, the material, and the opportunity and that the miners, on the other hand, will supply such effective labor that both parties will profit from the arrangement. Prices are seldom discussed at the time of hiring. The miner, in effect, is hired for a definite working place, as a contract miner, and if satisfied, tries to earn as much as he can. If he is not satisfied three courses are open to him: he can quit, he can ask for a change, or he can discuss prices or improved working conditions with the mine superintendent. This rather informal arrangement is due to conditions that are particular to Butte

Jan 2, 1961

By Charles S. Barrett

There is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 2o years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold-worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calori-metric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.l When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. I, which represents a narrow beam containing X-rays of many wave lengths (''general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By Charles S. Barrett

THERE is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall, attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 20 years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold Worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calorimetric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.1 When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. 1, which represents a narrow beam containing X-rays of many wave lengths ("general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By S. Ramachandran, L. A. Vazquez, N. L. Grauerholz

A novel process is described for the selective flotation of scheelite from low-grade (- 0.5% W03) tungsten ores having appreciable quantities of calcareous and siliceous gangue minerals. Specifically developed for the Tempiute, Nevada facility of Union Carbide, the process yields tungsten concentrates exceeding 15 percent W03 with at least 85 percent recovery. This condition was not achieved through conventional processes. This process consists of conditioning the ore pulp with judicious amounts of lime, followed by soda ash and sodium silicate as modifiers. The scheelite is then floated using a mixture of oleic and naphthenic acids as collector. Contrary to the common observation as to the deleterious effects of calcium in fatty acid flotation systems, lime addition is found to be beneficial in achieving satisfactory results. The process has also shown excellent results on a Brazilian scheelite ore.

Jan 1, 1976