Search Documents

By R. D. Taylor, Jim Douglas Jr., H. H. Rachford Jr., P. M. Dyke

A major obstacle to the use of wetting agents in .secondary recovery by water flooding is the adsorption of the agents on the sand. As a result of adsorption, the surfactant always lags behind the floodwater front. Consideration of the chromatographic theory of adsorption indicates that the detergents will not lag as much if used in very high concentrations. An investigation was made of the possibility of using high concentrations economically by flowing slugs of wetting agents followed by normal flood water. The experiments consisted of adsorption studies on Alundum powder and Berea sandstone. Flow rests on a 12-in. Alundum core and 22-in. Berea core were used to determine rate of detergent movement. The results of the flow experiments indicate that the relative rate of surfactant advance is, indeed, sensitive to the concentration of the agent. A 10 per cent slug moved with a rate that war 78 to 95 per cent as fast as the rate of advance of the flood water. By contrast, one with 25 ppm (the number of parts of commercial detergent in a million parts of water on a weight basis) concentration moved less than one-fourth as fast as the flood water, and calculations indicate that in very long porous systems the rate of movement of the lower concentrations will be a small fraction of the rate of advance of the flood front. The results. of the adsorption studies were utilized to calculate the rate of advance of the detergent when only the initial concentration was known. The calculated rates showed substantial agreement with the experimental flow tests in the high concentration ranges. The adsorption results were also used to estimate the cost of the materials for a slug-type surfactant flood in the field. In addition to the faster rates of movement, the concentrated detergent slugs removed much more oil than the dilute solutions. However, the effectiveness of the slug process depends on many variables. The quantity of oil removed is increased markedly by increasing the flooding rate. The efficiency is also influenced by the type of crude, type of reservoir rock and initial water saturation. Therefore, a careful analysis of each reservoir system is required before the economic value of the process can be determined. INTRODUCTION It is well known that the displacement of oil by invading water during water flooding is far from complete. It is generally agreed that the unrecovered oil is retained in the porous medium by the capillary forces which may be relatively large compared to the forces generated by the flowing water. Therefore, it was logical that some early workers should turn to surface-active materials to reduce the capillary forces to facilitate the release of oil. As early as 1927,' a patent was granted for the use of surface-active materials in water flooding. In 1932, when soap solutions were passed through Bradford and Venango sands, it was reported that the results were inconclusive, erratic and that "further investigation is needed to determine exactly the function of the solution and to obtain a clearer insight into the phenomena involved."' Some of the modern scientific reports conclude with a similar statement,' showing that the lack of agreement on the mechanism of oil removal by wetting agents is still very widespread even though several comprehensive studies have been reported.'." Although there is a lack of agreement as to the general effectiveness of the detergents for water flooding, most investigators do agree that all of the common detergents are strongly adsorbed onto the solid surfaces of the reservoir. In the early calculations it appeared that all additives would be lost before reaching much of the formation area which contained the additional oil to be removed. Experiments indicated that if the usual small waterflood concentrations of wetting agents were used, the rate of advance of detergent through the formation would be only a small fraction of the rate of advance of the flood front. Indeed, some investigators4 felt that the use of wetting agents would never be economically feasible because of their adsorption. For example, DunningG estimated that the wetting agent in concentrations of 25 ppm, would advance only 0.05 times as fast as the flood front. Ojeda, et al,' found that a surfactant in a concentration of 10 ppm moved less than 0.01 times as fast as the flood front. It is significant, however, that both investigators found that increased concentrations of wetting agents moved faster, relative to the flood front, than solutions at the lower concentrations. Ojeda showed that an extrapolation of his data indicated a relative rate of 0.5 at 1 per cent concentration, while Dunning6 estimated a relative rate of 0.46 for a 1 per cent concentration. It was obvious that these concentrations could not be used for continuous injection because the cost of the injected detergent would far exceed the value of additional oil produced. Traditionally, detergents are used in very low concentrations for they show good

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By C. A. Stout, S. W. Nicksic

The materials that stubilize emulsions of some Southern California crude oils were isolated from the produced crude. These substances were separated into acidic and nonionic fractions by ion exchange chromatography. Each fraction was further broken into groups of homogeneous molecular weight composition by gel permeation chromatography. Both ionic character and molecular weight of the individual fractions are reflected in the properties of the original crude oil emulsion. Specifically, the more acidic and the higher molecular weight fractions appear to be the most effective stabilizers. INTRODUCTION The treatment of oilfield emulsions is a continuing problem for the oil industry. In almost all cases, these are water-in-oil emulsions. Much more is known about the formation and stabilization of oil-in-water (O/W) emulsions than of the water-in-oil (W/O) type. To understand W/O emulsions, more information is needed on the materials responsible for their formation and stabilization. This is especially true in the case of oilfield emulsions where the stabilizing materials are complex mixtures of large asphaltene-like molecules. To study the chemical and physical properties of these emulsion stabilizers, it is necessary first to separate them from crude oil. This separation was achieved in the case of two Southern California crude oils. The materials that were isolated appear at first to be little different from an asphaltene mixture. However, if a mixture of distilled water and mineral oil containing about 1 percent of the natural emulsion stabilizers is passed through a colloid mill, the W/O emulsion formed may be stored in the laboratory for many months without any sign of breaking. This could not be done using undifferentiated asphaltenes from the same wells, indicating that there is a real difference between these materials and ordinary asphaltenes. The colloid mill used to generate the emulsion was required because tile natural emulsion stabilizers had very little effect on oil-water interfacial tension. The one characteristic — complexity of composition — that emulsion stabilizers share with asphaltenes makes virtually impossible the exact structure determination of the components of the mixture. For this reason, it was decided to investigate first the influence of molecular weight on the ability of these materials to stabilize emulsions. The emulsion stabilizers were first separated into acidic and neutral fractions according to whether or not the material was retained on a weakly basic ion exchange column. The extraction procedure was not designed to remove basic components from tile oils, and no attempt to isolate such a fraction was made. Following this separation, selected fractions were analyzed by gel permeation chromatography. Gel permeation separates according to molecular size, largely independently of chemical or polar characteristics. A heterogeneous mixture is separated into a number of fractions having much more homogeneous molecular weight distribution. A number average molecular weight of each fraction is therefore close to the true molecular weight of the principal component of that fraction. The fraction weights, expressed as weight percent of the sample, and the number average molecular weight of a representative selection of the fractions, will be referred to in this paper as the molecular weight profile of the original sample. DESCRIPTION OF GEL PERMEATION ANALYSIS The first reported gel permeation analyses were for separating partially hydrolyzed protein molecules in an aqueous system using expanded starch granules. Most of the theoretical work on gel permeation has been done by biochemists.1 This theoretical treatment is still incomplete, but the

Jan 1, 1969

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By Henry N. McCarl

Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in port- land cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggre- gate materials. The value of mineral aggregate materials at the production plant varies from less than a dollar per ton to several dollars per ton for most crushed stone and sand and gravel, $2 to $15 per ton for slag and expanded clay or shale aggregate, to as much as $60 to $100 per ton for expanded perlite or vermicu- lite. The more specialized the use, the higher the price-although there are naturally some exceptions to this rule of thumb. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Light- weight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks there will also be some coverage of sources, mining and production, especially in those cases where they are

Jan 1, 1975

By William A. Mitchell

AN X-ray diffraction pattern for "calcined cold precipitated ferric oxide" is reproduced dia-grammatically along with data for other iron oxides by R. C. Mackenzie.1' This pattern, which shows spacings higher than those for any other form of iron oxide, was obtained from material prepared and photographed at several different times over a period of weeks, but later attempts to reproduce the results were unsuccessful, the pattern of hematite being obtained every time.2 In an attempt to solve this problem, the original photographs showing the strange diffraction pattern were examined and a marked similarity to the hematite pattern was noticed, suggesting that the pattern was in fact due to hematite but corresponded to a shorter wavelength of X-rays than the Cu Ka which was assumed to have .been used. The eight strongest lines were provisionally identified with the strongest hematite lines and, by means of the corresponding hematite spacings, the X-ray wavelength was calculated for each line. This gave an almost constant value, with the exception of the innermost line which was somewhat diffuse, and confirmed the presence of hematite. The value obtained, 0.703 ± 0.015Å, corresponds to the molybdenum Ka wavelength. The X-ray tube used was a four-filament demountable tube with a copper target. Other photographs, mostly of soil clays, taken during the same period gave normal patterns of Cu Ka radiation with one exception. This was a calcined soil clay with a high iron content and also showed Mo Ka lines of the hematite structure. The explanation is almost certainly that the copper target was contaminated with molybdenum, but it is not known how this occurred. Specimens of alumino-silicates gave their normal Cu Ka pattern, but as the K absorption edge of iron is a little longer than the Cu Ka wavelength, specimens with a high iron content greatly reduced the intensity of the Cu Ka diffraction lines relative to that of the lines due to the shorter Mo Ka wavelength. The formation of hematite on calcining cold precipitated hydrated ferric oxide3 is thus confirmed. References R. C. Mackenzie: Investigations on Cold-precipi-tated Hydrated Ferric Oxide and its Origin in Clays. Problems of Clay and Laterite Genesis, p. 69, Fig. 4, F. AIME Symposium, St. Louis, Mo. Feb. 19-22, 1951. Published 1952. 'R. C. Mackenzie: Ref. 1. Note added on proof. V. C. Hansen and L. T. Brownmiller: Equilibrium Studies on Alumina and Ferric Oxide and on Combinations of These with Magnesia and Calcium Oxide. American Journal of Science (1928) 5, No. 15, pp. 225-242.

Jan 1, 1954

W. D. BRENNAN,* Cheyenne, Wyo. (written discussion?).-My experience has been that, where possible, it is preferable for each foreman to employ his own men, rather than to have them handled through an employment bureau. The fact that each foreman comes into direct contact with the man before he is put to work gives him an opportunity to choose, at certain times, the kind and class of men that he wishes. Where possible, after a man is employed he is sent to a central office where a complete history of each individual is kept on a card. If a man has previously been in the employ of the Company, his history can be obtained from this card, and if for any reason he is not wanted he can be refused work at the time he reports to, the central office. In connection with Workman's Compensation costs, we in Wyoming feel that although the rates of compensation paid may in some cases be rather low our law works satisfactorily. As the State and the number of employees are small, compensation cases are handled through Judges of the various District Courts. In the State Treasurer's Department, a few clerks were added to look after the handling and issuing of warrants and compiling of statistics. Most of the large employers have an arrangement by which a joint claim and assent, specifying the amount of compensation due, is made tip by the employer and signed by the workman. This is forwarded, to the Judges so that personal investigation of individual cases is not necessary. In this manner, compensation is promptly received and' overhead expenses of operation of the law is kept at the minimum. The law requires each employer to pay into the State Treasury, for the benefit of the industrial fund, a sum equal to 1.5 per cent. of the money earned by each employee, engaged during each calendar month of such employment. Each employer contributes monthly, unless the sum heretofore contributed, after deducting all payments made on account of injuries to his employees, shall equal a full 1.5 per cent. of his annual pay roll, computed by multiplying his current monthly pay roll by twelve, and shall likewise be not less than ($5000). It has been found during the years that this law has been in effect, that a number of the larger employers have been exempt from payment for from five to eight months per year, so that in some cases, even in coal nines, industrial insurance has cost less than 0.75 per cent.

Jan 3, 1919

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By T. E. Leontis

ONLY a limited amount of information has been published on the effect of thorium as an alloying ingredient in magnesium. McDonald13'2 showed that the addition of thorium in amounts up to 3 pct increases significantly both the ductility and the strength of rolled magnesium sheet. A recent publication by Sauerwald" indicates that thorium contributes strength and creep resistance at elevated temperatures to magnesium in both the cast and wrought states. The observations of Sauerwald are confirmed in this paper, which presents the results of a systematic study of the effects of compositional variation on the tensile properties, creep resistance, conductivity, density, and metallography of Mg-Th alloys containing up to 50 pct Th both in the sand-cast and in the extruded states. The effect of the addition of cerium to Mg-Th alloys is also reported. Experimental Methods The alloys studied in this investigation were pre.pared in small laboratory melts according to the melting practice described by Nelson4 as the crucible method. Electrolytic magnesium was used as the starting material to which the thorium* was introduced in metallic form. It was observed that the behavior of thorium in molten magnesium with respect to reaction with protective fluxes is similar to that of rare-earth metals. In order to obtain the highest possible alloying efficiency, it is necessary to use non-MgC1, fluxes and to apply all the precautions described by Marande6 for melting, alloying, and casting magnesium-rare-earth alloys. .Under these conditions it is possible to obtain an alloying efficiency in the range of 85 to 95 pct. The Mg-Th-Ce alloys were made with cerium of the highest purity available, not with the commercial product "misch-metal" which contains approximately 50 pct Ce. The total rare-earth content of this material was 97.1 pct, of which 0.3 pct was rare-earth metals other than cerium; the major impurities comprising the balance were iron and magnesium. The thorium and cerium contents of each alloy were determined chemically. Test bars 6% in. long with a 2% in. long reduced section of % in. diam were cast in sand molds using a four-baf pattern. In most cases, a 3 in. diam extrusion billet 10 in. long was cast in a steel mold from the same melt used for making the sand-cast test bars. For the higher thorium alloys, it was necessary to remelt the foundry scrap from the test bars in order to make the extrusion billets. The billets were scalped to a diameter of 2 15/16 in. and the ends faced to a length of 9% in. as limited by the size of the extrusion container. The alloys were extruded into % in. diam rod on a 500-ton direct-extrusion press. The details of the extrusion process are as follows: Billet preheat 925°F (2 to 16 hr) Container temperature 900 °F Die temperature 900°F Extrusion speed 10 ft per min Reduction ratio 36:1 Percent reduction 97.3 Alloys containing up to 10.2 pct Th were preheated at 925°F for 2 hr; all alloys with higher thorium contents were preheated for 16 hr. In order to establish the effect of extrusion temperature, billets of

Jan 1, 1953

By R. J. Blackwell, J. R. Rayne, W. M. Terry

This paper presents results of an experimental investigation of factors that control the efficiency with which oil is displaced from porous media by a miscible fluid. The study was made to elucidate the relevant processes both on microscopic level (within individual or between neighboring pore spaces) and on macroscopic level (within a large sand body). Mixing of miscible fluids on the microscopic level was studied in sand-packed tubes. It was found that molecular diffusion is the dominant dispersion mechanism for reservoir conditions of rate, length and pore sizes. Macroscopic channeling was studied for various mobility ratios in reservoir mode1s scaled to relate viscous, gravitational, and diffusional forces. The formation of channels was due to viscous firzgering, gravity segregation and variations in permeability. With adverse mobility ratios, it was found for reservoirs of realistic widths that diffusion will not be effective in preventing the formation and growth of fingers, even in homogeneous sands. At sufficiently low rates channeling was eliminated by gravity segregation in tilted reservoirs. The dependence of recovery on mobility ratio, length-to-width ratio, flow rate and angle of dip is presented. INTRODUCTION Oil recovery by solvent flooding is finding increasing application in the field. While the process promises high recoveries from the region swept by solvent, under adverse conditions only a small fraction of the reservoir volume may be swept at the time solvent breaks through to the producing well. Further, the high cost of the solvent encourages its use only as a bank whose size must be kept at a minimum. Thus, two important questions arise: (1) what fraction of the reservoir can be swept, practically, by solvent? and (2) what is the minimum size solvent bank that can be used to carry out the displacement? The answers to these questions require knowledge of both macroscopic channeling processes and microscopic mixing processes. The studies described here were carried out to gain this knowledge. Microscopic mechanisms which cause mixing will be discussed first, because an understanding of these mechanisms is necessary for proper interpretation of the experimental work on channeling described later. INVESTIGATION OF MICROSCOPIC DISPLACEMENT PHENOMENA FOR MISCIBLE FLUIDS The questions to be resolved concerning microscopic displacement behavior are: (1) how much mixing occurs between oil and solvent in the direction of flow? and (2) does the solvent completely flush the oil from the pore spaces in the region invaded by solvent? The classic work of Sir Geoffrey Taylor' and its extension by Aris2 have shown that it is possible from theory to describe the amount of mixing in single straight capillaries when solvent displaces a fluid of equal viscosity and equal density. Aris showed that the lengths of the mixing zones, 81, corresponding to the 10 per cent and 90 per cent concentration levels of the solvent can be calculated from the formula, 81 = 3.62 \/Kt, .........(1) where 8l is the length of the mixing zone, cm; t is the time, sec; and K is the effective dispersion coefficient, cm2/sec, given by K/D = 1 + (1/48) (au/D)2......(2) where a is the radius of the capillary, cm; D is the molecular diffusivity, cm2/sec; u is the average velocity

By H. A. Jr. Koch, C. A. Hutchinson

Miscible phase displacement of oil from reservoirs has been emphasized in the past few years. The reason for this emphasis lies in the high oil recovery attainable by this process. Removal of capillary effects in the reservoir leads to recoveries approaching 100 per cent in the area contacted by the miscible phase. The miscible slug process is one means of obtaining a miscible displacement. Here a band or slug of I,PG is injected into the reservoir prior to gas injection. The idea is to maintain the band of LPG "wedged" between the gas and oil phases and thus achieve a miscible phase displacement. A second method lor achieving miscibility is through the injection of a gas which is not miscible with the reservoir fluid but which develops a zone of miscibility in [he reservoir through mass trans-ier with the reservoir oil.' This mass transfer results in either an enrichment of the lean injected gas by intermediates from the oil or an enrichment of the oil by intermediates from a rich injection gas or one that has been enriched on the surface by LPG addition. We are interested here in discussing the process in which miscibility is developed at the displacement front by the evaporation of interrnediatcs from the oil phase into the gas phase. This process "builds up" its own slug of miscible material at the displacement front and therefore does not require the injection of LPG to obtain miscibil-ily. Each process has its own area of applicability. Generally, the high pressure gas process is applicable only with reservoir fluids which con-!ain a high concentration of inter- mediates. If the high pressure gas process is technically feasible at pressures less than 4,500 psi, it is probably more desirable economically than the slug process. The slug process has broad applicability in the shallower reservoirs and with reservoir fluids which contain a relatively low concentration of LPG and natural gasoline constituents. This paper deals with some new concepts of the high pressure gas injection process where it is proposed that flue gas can be substituted for hydrocarbon gas without sacrificing our goal of miscibility. MECHANISM Introduction Considerable effort has been devoted to study of the mechanics ot the high pressure gas injection proc-one generalization result-ing from some of these studies was that the composition of the injected gas is relatively unimportant in establishing the miscibility pressure* for a given reservoir fluid. This generalization is correct for the composition range of gases typically encountered in the field. Two such gases are a gasoline plant tail gas containing 85 per cent methane and 15 per cent ethane, and a field separator gas containing 70 per cent methane and 30 per cent heavier components. The most important factor which sets the miscibility pressure in the operation is the reservoir fluid composition, particularly the concentration of LPG-natural gasoline constituents. The injected gas is the agent by which the LPG-natural gasoline constituents are concentrated at the displacing front to create a miscible displacement. Based on these results, it appeared feasible that some inexpensive gas, such as flue gas, might be substituted for hydrocarbon gas for use in the high pressure gas process. A re-examination of the phase relations of the high pressure gas injection process should clarify the principle behind using flue gas (essentially nitrogen) as an injection gas. Three Component Diagram The phase relations of the high pressure gas injection process have been illustrated by the use of the three component diagrams.'," In Fig. 1 we have arbitrarily represented the multi-component reservoir system by three components; methane, ethane through hexane, and heptanes plus. The solid curve ABC is the phase boundary curve. It represents the locus of compositions which have fixed saturation pressure at a fixed temperature; the lower branch AB shows bubble point compositions, the upper branch BC, the dew point compositions. Point B is the coniposition of the critical mixture at this temperature and pressure. The dashed lines (tie lines) connect vapor and liquid compositions which are in equilibrium. Let us consider Reservoir Fluid D which we wish to displace in 21 miscible manner by gas injection. Let us further restrict the discussion to the case where miscibility between an injection gas and the reservoir fluid at the displacement front is developed by gas enrichment in the reservoir. For this case, any gas whose composition lies between Points C and E on the right side of the three component diagram can be used to give a miscible displacement of Reservoir Fluid D. This is true because the more mobile injected gas moves faster than the displaced oil and is in continuous contact with virgin oil at the displacement front. This leads to a continuing enrichment 01' the gas at the displacement front by evaporation of the C, - C,

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968