Search Documents

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By Roberts H. Richards

It is nearly twenty years since Dr. Raymond, then U. S. Commissioner of Mining Statistics, wrote the first paper (so far as I have been informed) upon the education of tile mining engineer, as a distinct profession for American youth. At that time nearly all the prominent mining engineers in the country had studied in one or more of the foreign schools, or had reached their high standing through years of experience in the school of life. The paper mentioned five schools in the United States in which some attention was paid to the teaching of mining engineering, but as four of them had barely graduated their first classes, their influence had not begun to make itself widely felt. Two years later the American Institute of Mining Engineers was formed, and it has been a most potent factor in the problem of "disseminating information on mining and metallurgical subjects," so potent that the need of a national school of mines as headquarters for information as well as for instruction is no longer urged. The number of schools also increased, and in 1876 Abram S. Hewitt, in his Presidential address on "A Century of Mining and Metallurgy in the United States,'' gave a list of fourteen. In 1876 the series of discussions, led by Holley's admirable paper, brought the whole subject of technical education before the country. These discussions, while mostly devoted to the engineering professions in general, touched upon the question of mining and metallurgicel training to some extent. Since that time several papers, inspired by the publication of that series of discussions, have appeared in our Transactions, and several notable addresses have been delivered at the opening or at the commencement exercises of various schools. But nothing directly bearing upon the curriculum of the mining and metallurgical schools has ever appeared in our annual volumes. As education is one of the many-sided subjects which cannot be discussed too often, I have ventured to bring it up again. There have been so many good things said upon the subject that one would only need to use the scissors and paste-brush judici

Jan 1, 1887

By Norman B. Pilling

The technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost' exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105' C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys. The reagent consists of a dilute solution of nitric acid and methyl alcohol in nitrobenzol. It is a great advantage to secure an anhydrous solution, as a tendency toward acidic etching has been traced to small amounts of water. A convenient method of preparation is to make an anhydrous stock solution of nitric acid in methyl alcohol in the proportion 20 per cent. acid by weight (12.5 per cent. by volume). The alcohol can

Jan 1, 1924

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.'" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long ''fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By C. G. Fink, E. P. Polushkin

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years were systematically surveyed and supplemented by new material obtained in examination of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors' chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper. Specimens Studied As the majority of specimens were very small and sometimes had a heavy coat of patina, or crust, which further reduced the amount of metal available for analysis, quantitative chemical analyses were not made. Small detached specimens were not always obtainable and studies had to be made on the statue, or other object, itself. In the description of specimens (Table I), their approximate compositions determined under the microscopc are given. The proportion of tin in bronze containing eutectoid was found by visual estimation of the area occupied by the eutectoid. It was based on the assumption that maximum solubility of tin in copper on moderately slow cooling is 7 to 8 per cent in thin castings and 9 to 10 per cent in heavy castings. When the metal was all

Jan 1, 1936

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By Kirby D. Mellegard, Ralph A. Wagner, Paul E. Senseny

Six creep laws for salt, each fitted to the same laboratory data base, are used in a numerical model of the deformation of an opening in salt to determine the influence of creep law form on the predicted closures. Results show that predicted closures can be very sensitive to the functional form of the creep law chosen to model the laboratory data.

Jan 1, 1982

By Bruce E. Grant, Thomas Jancic, Lawrence G. Dykers, Frank Buchella

Principal factors influencing equipment selection can be grouped into five basic categories: tonnage requirements, ore and waste; topography and property line considerations; ore control requirements; physical characteristics of ore and waste; and climatic considerations. Loading, transporting and ground preparation equipment are largely determined by tonnage requirements. Large size equipment is appropriate for a production of about six million tpm, medium size for three million tons and small size for one million tons or less.

Jan 12, 1973

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949

By E. Baker, David Donoghue

Legal and legislative matters constituted the outstanding features of proration in Texas in 1932. From East Texas emanated most of the political, legal, technical and industrial activity. Conroe and Thompson developed into fields of major importance. Proration orders were issued by the Railroad Commission on many of the producing fields of the Gulf Coast and West Texas not covered in previous years. In Yates, Penn Pool, Winkler, Van, the Panhandle, North Texas and West Central Texas there were 110 changes of importance, except in allowables. New proration schemes were introduced in East Texas, Conroe, Thompson, Saranosa, Government Wells, Tuleta and Howard-Glasscock. Little progress was made in administration or technical development. Legal and Legislative Matters Proration first began in Texas in 1927 as a voluntary attempt to divide the market outlet of a field on an equitable basis. The statutes then in existence were considered somewhat archaic and the Railroad Commission's authority was limited. Subsequent efforts to strengthen the laws were not wholly successful. The 1929 Conservation Act made no mention of market demand but declared that the term "waste" did not mean " economic waste." With the passage of the Pipc Line Act of 1930, providing for ratable purchasing, it was the opinion of many lawyere that a legal means of proration had been found. The 1931 law had ths same provision as that of 1929 with respect to economic waste but specifically prohibited limiting of production to market demand. The law passed Nov. 12, 1932, omitted reference to economic waste and specifically provided for limitation of production to reasonable market demand. Vigorous attacks were being made in State and Federal Courts on the constitutionality of the laws and the validity of the Commission's orders. In Peoples Petroleum Producers, Inc. et al. vs. Lon A. Smith et al., which had been heard before a three-judge U. S. District Court in Houston on May 28, 1932 and again on Sept. 19, the Court's decision for plaintiffs, released Oct. 2, influenced in a large measure the calling of the Legislature and the passage of the Market Demand Law on Nov. 12.

Jan 1, 1933

By C. K. Leith

AT the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, role to recrystallization in development of these zones. With the growing recognition, of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zone. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raise the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrystallization.1 The inevitable sequence has been that those of us who have taken this view have been charged, at least by inference, with emphasizing recrys-tallization to, the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 6, 1914

By C. K. Leith

At the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the- sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, ro1e to recrystallization in development of these zones. With the growing recognition of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zonc. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raisc the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrysta11ization.l The inevitable sequence has been that those of us who have .taken this view have been charged, at least by inference, with emphasizing recrystallization to the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 1, 1915

By H. K. Shearer

North Louisiana (including all townships north of the Louisiana base line) had a year of normal development in 1940, marked by the discovery of two shallow oil fields producing from the Wilcox formation in La Salle Parish and a large increase in drilling in the old Caddo shallow field. This renewal of shallow drilling activity led to a somewhat unexpected increase in the number of wells drilled, although the total footage and average depth continued to decline, as in several preceding years. Well completions and depth statistics for 1940, with previous years for coinparison, are as follows: Wildcat producers in 1940 include the discovery oil wells in the Olla and Nebo fields; also three gas wells in the vicinity oi the Olla field and a shallow gas well, which opened a new field or extension in the Greenwood area of Caddo Parish. This table illustrates the lack of important deep discoveries since 1937, in which year the Rodessa, Lisbon and Cotton Valley fields were being actively developed. Operators have been forced to return to the old type of shallow drilling, which necessarily means smaller producing wells. Oil production in 1940 was 24,381,760 bbl., a decrease of 867,880 bbl. from 1939, or 3.44 per cent. The newly discovered fields of La Salle Parish produced over a million barrels, and other increases worthy of note were at Cotton Valley, Caddo, Sligo and Sugar Creek. The greatest decrease was again at Rodessa, although this remains the principal producing field. Geological Names Revised Deep drilling during 1940 did not provide a great deal of new geological information. However, by agreement of a majority of the members of the Shreveport Geolog- ical Society, the names of some of the Lower Cretaceous formations have been revised in the interest of greater clarity and in order to make the descriptions agree better with the facts discovered in recent years. The geological section is discussed in detail and reasons for changes in nomenclature are stated in a recent publication by Ralph W. Imlay. Although not yet in universal use among field men, the new names are employed in this report and accompanying tables, as

Jan 1, 1941

By H. K. Shearer

North Louisiana (including all townships north of the Louisiana base line) had a year of normal development in 1940, marked by the discovery of two shallow oil fields producing from the Wilcox formation in La Salle Parish and a large increase in drilling in the old Caddo shallow field. This renewal of shallow drilling activity led to a somewhat unexpected increase in the number of wells drilled, although the total footage and average depth continued to decline, as in several preceding years. Well completions and depth statistics for 1940, with previous years for coinparison, are as follows: Wildcat producers in 1940 include the discovery oil wells in the Olla and Nebo fields; also three gas wells in the vicinity oi the Olla field and a shallow gas well, which opened a new field or extension in the Greenwood area of Caddo Parish. This table illustrates the lack of important deep discoveries since 1937, in which year the Rodessa, Lisbon and Cotton Valley fields were being actively developed. Operators have been forced to return to the old type of shallow drilling, which necessarily means smaller producing wells. Oil production in 1940 was 24,381,760 bbl., a decrease of 867,880 bbl. from 1939, or 3.44 per cent. The newly discovered fields of La Salle Parish produced over a million barrels, and other increases worthy of note were at Cotton Valley, Caddo, Sligo and Sugar Creek. The greatest decrease was again at Rodessa, although this remains the principal producing field. Geological Names Revised Deep drilling during 1940 did not provide a great deal of new geological information. However, by agreement of a majority of the members of the Shreveport Geolog- ical Society, the names of some of the Lower Cretaceous formations have been revised in the interest of greater clarity and in order to make the descriptions agree better with the facts discovered in recent years. The geological section is discussed in detail and reasons for changes in nomenclature are stated in a recent publication by Ralph W. Imlay. Although not yet in universal use among field men, the new names are employed in this report and accompanying tables, as

Jan 1, 1941

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John Buch

NEARLY 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining under-lying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading' was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechan-ical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1939

By Paul T. Allsman

1.1-1. Current Status. The history of surface mining is essentially that of mining coal, copper, and iron ores, and the nonmetallic minerals--clays, gypsum, phosphate rock, sand, gravel, and stone. Table 1.1-1 is a comparison of the estimated world production of crude metallic and nonmetallic ores and coal with that of the United States for 1964, in short tons. It includes an estimate of the quantity produced by surface mining methods. Two-thirds of the 8.8 billion tons are mined from surface, ranging from a third of the coal, half the metallic ores, and nearly all clays, stone, sand, and gravel. In the United States, production by surface methods parallels that of the world with two major exceptions: 74% of copper ore and 90% of usable iron ore are mined from the surface, whereas outside the country less than 40% of copper ore and only 50% of usable iron ore are mined from the surface. In surface mining of both metallic ores and coal, much waste is stripped, but in mining nonmetallics the ratio between waste and ore is small. Assuming that the stripping ratio for surface mining in the United States will apply equally to world production, it is estimated on a weighted basis that over 21 billion tons of waste, or a total of nearly 27 billion short tons of material, are mined annually in the world by surface methods. Data are not available to confirm the assumption for waste stripping outside the U.S., but the estimate expresses an order of magnitude that is worth noting. Table 1.1-2 shows the materials-crude ore, coal, and waste-mined by surface methods and the relation to total mined by both surface and under- ground methods in the United States during 1964. Eighty-two percent of all crude metallic and nonmetallic ores and coal was mined from the sur- face, including 82% of metallic, 96% of nonmetallic ores, and 35% of coal. Copper and iron ore comprise 83% of the metallic ores mined from the surface, and clays, gypsum, phosphate rock, sand, gravel, and stone

Jan 1, 1968

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By William H. Grady

FactoRs entering into the market value of coal are its grade, and the cost of labor, material, and capital. Reduction in these costs cannot be expected in the future, and it therefore follows that greater economy in their use must be accomplished if it is desired to hold the present markets; more tons of product per unit must be obtained in a given time from both men and material, and means devised for increasing the percentage of lump and domestic sizes. This paper is presented for the purpose of inviting discussion and stimulating thought in regard to the influence of methods of procedure and plans of mining, upon the quality of coal, the economical use of labor, material, and capital, and the cost of production. Even the better methods of the present day leave much to be desired, and a review of the reasons and necessities for their use may be of value in pointing the way to more economical mining. The writer does not attempt to discuss untried methods of mining, but rather to state clearly and concisely a summary of the results obtained under the several methods of procedure that have been adopted. In some instances a high degree of concentration has been effected, and comparisons of the results obtained with the results of lesser degrees of concentration form an interesting study. It is believed that much may be accomplished in improving the quality, and in the more economical use of labor, material, and capital, by concentration, and it is to concentration in particular that your study is invited. The writer, who has occasion to visit many mines, most of which are under different management, has been inclined to the opinion that improvement has been retarded in many ways and that mining has not as yet been entirely freed from the early-day practices which were forced upon it. Practices resulting in lack of concentration, to which reference will be made, are: The absence of robbing, necessitating the frequent interposition of barrier pillars; lack of system and of proper supervision, resulting in losses of life and coal. These practices could not well be

Jan 1, 1915