Search Documents

By H. G. Doll, H. P. Schwede

This paper describes a method to provide identification of particular depths in a borehole through the use of radioactive markers. The correlation of a marker, placed in the wall of a borehole, with known points of the electrical log and with the casing collars in the cased hole permits accurate positioning of tools with respect to a formation, regardless of absolute depth. Such a process is particularly useful in gun perforation of a casing in a well. Technique and equipment are discussed and illustrated. Examples are given of practical application in the field. Introduction During the past decade the search for petroleum has increased the importance of testing zones at depths in wells which have become progressively deeper. The development of new techniques, such as electrical logging, has permitted the identification of producing formations which consist of comparatively thin strata. When thin beds are to be produced at great depths, the problem of positioning tools accurately to place the well in production becomes acute.l Continuous consideration is being given in the petroleum industry towards the improvement of depth measurements in a borehole. The accuracy in absolute depth measurements, whether made in an open or cased hole, whether determined by a cable or a drill pipe, depends upon a number of factors, such as tension, temperature, and calibration. For example, the effects of tension from the weight of 10,000 ft of drill pipe and the thermal expansion of this length . of pipe, where its average temperature has increased SO"', will Produce an elongation as much as 8 ft.2 The effects Of such factors can be minimized through the use of care in depth measurements, the application of corrections based on experience, and continuous calibration or checking. The fact that different methods and different tools are used to determine the depths of formations in wells will sometimes give rise to a difference between measurements. It is evident that an important requirement in a well is the ability to locate at will any subsurface point. While absolute depth measurements have ion in recent years, it is reassuring to have other means to verify, for example, that a casing is perforated at a particular place with reference to a zone within a formation. Such a check on measurements may be had by placing a reference marker at a point known with respect to the electrical log of the borehole. That point is usually chosen to be in proximity to the 'One to be perforated. Thus, only short in depth measurements are made and any inaccuracy becomes very small and of minor importance' The use of reference markers located at fixed points predetermined in each zone where future operations are contemplated enables the operator to position any tool

Jan 1, 1948

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962

By Simon D. Strauss

COPPER In terms of mining activity, copper is the leading nonferrous metal. It is true that in recent years the volume of aluminum consumption in the non-Communist world has exceeded the volume of copper consumption, but virtually the entire primary aluminum supply is derived from bauxite. On the average, only four tons of bauxite need be mined to produce a ton of aluminum. By contrast, the highest-grade, large-scale copper mines now in operation (those in the Congo) must mine at least 20 tons of ore to produce a ton of copper. In the United States an average of 150 tons of ore must be mined to produce a ton of copper. This does not take into account the huge amounts of waste overburden that must be stripped from the open-pit mines to account for their steadily rising share of the world's copper output. Copper epitomizes the economic problems of the mining industry in many ways. Its price is highly volatile, considering its great economic importance. It has been a tool of mankind longer than any other of the base metals-the dawn of history has been classified as "The Bronze Age." World Copper Production Although copper is mined in many countries, in recent years 70% of the non-Communist world production has come from six countries. Two of these are industrialized countries and are large consumers-United States and Canada. The other four are developing countries with very small domestic requirements-Chile, Zambia, Zaire, and Peru. Heavily dependent on copper exports to sustain their domestic economies, these countries find themselves oscillating between prosperity and depression with the changing levels of copper prices. In an effort to control their own destiny, in 1968 they formed an organization of copper exporting countries (CIPEC) which was designed to study copper markets and possibly to intervene actively in these markets. (When this chapter was being prepared, no actual steps along such lines had been taken.) Many of the leading industrialized nations are wholly dependent on imports for their primary copper supplies. These include West Germany, the United Kingdom, France, Italy, and many others. Japan, now the non-Communist world's second largest copper consumer, produces only 10 to 15% of its requirements from domestic mines. Although the bulk of the copper output is smelted in the country where it is mined, there is a limited international trade in copper concentrates. Canada, the Philippines, Australia, and Papua-New Guinea are significant exporters of copper concentrates; Japan, Germany, the United States, and Sweden are importers. However, this trade accounted for only about 10% of the non-Communist world production of copper during the decade of the 1960s.

Jan 1, 1976

By T. Y. Yan

SUMMARY Laboratory high pressure column tests have shown that the presence of 1-20 ppm of aluminum ion effectively prevents permeability loss during uranium leaching with leachates containing sodium carbonate. If added after permeability loss has occurred, aluminum ion can restore the permeability to nearly its original value. No deleterious effect was observed on uranium leaching performance and the technique should be quite compatible with all field operations. INTRODUCTION The recovery of uranium values from underground deposits by in situ leaching or solution mining has become economically viable and competitive with conventional open pit or underground mining/milling systems (Merrit, 1971). In situ leaching processes are particularly suitable for small, low-grade deposits located in deep formations and dispersed in many thin layers. Many such ore bodies occur along a broad band of the Gulf Coastal Plain (Eargle et. al., 1971). The advantages of the in situ leaching processes have been reviewed (Anderson and Ritchi, 1968). In the in situ leaching process, a lixiviant containing the leaching chemicals is injected into the subterranean deposit and solubilizes uranium as it traverses the ore body. The pregnant lixiviant or leachate is produced from the production well and is then treated to recover the uranium. The resulting barren solution is made up with the leaching chemical to form lixiviant for re-injection. Upon completion of the leaching operation, the formation is contaminated with leaching chemicals and other species made soluble in the leaching operation and has to be treated to reduce the concentration of these contaminants in the ground water to levels acceptable to the regulatory agencies (Witlington and Taylor, 1978). Restoration is accomplished by injecting a restoration fluid, which could be the fresh water or water containing chemicals, into the formation. As it traverses the leached formation, the restoration fluid picks up the contaminants and is then produced at the production well. This produced water is either disposed or purified for recycle. In both phases of operation, formation permeability or well injectivity is one of the most important parameters which determines the viability of the in situ leaching process. Low formation permeability limits production rates, leading to uneconomical operations. The formation is said to be sensitive if there is a sharp loss of permeability on contact with water and other fluids. Many uranium bearing formations, for example, the Catahoula formation of the Texas Coastal Plain, contain significant amounts of clay minerals which are water sensitive. Serious permeability losses can occur when the pH and chemical composition of the lixiviant is significantly different from that of the formation water. Jones has investigated the influence of chemical composition of water on clay blocking of permeability (Jones, 1964) and Mungan studied permeability reduction through changes in pH and salinity of the water (Mungan, 1965). Various mechanisms of permeability damage have been proposed and reviewed (Jones, 1964; Mungan, 1965; Gray and Rex, 1966; and Veley, 1969). When large amounts of swelling clays are present, a significant fraction of the flow channels in the formation can be reduced due to swelling. However, in most cases, swelling need not be the main cause of permeability losses. Particle dispersion and migration or clay sliming can be more important causes for formation damage. Clay particles entrained in the moving fluids are carried downstream until they lodge in pore constrictions. As a result, microscopic filter cakes are formed by these obstructions, plugging the pores, effectively restricting fluid flow and reducing the formation permeability. Moore found that as little as 1-4 percent clays present in a fine grained sandstone could completely plug the formation if they are contacted by incompatible injected fluids (Moore, 1960). It has been found that injection of NaHC03/Na2CO3 lixiviant into formations with significant clay content often leads to loss of formation permeability and well injectivity. To alleviate this problem a change of the lixiviant composition to KHC03/K2CO3 has been proposed. At present, however, many in situ leaching operations employ NH4HC03/(NH4)2C03 mixtures as a source of carbonates. This approach has been successfully used in South Texas by Mobil, Intercontinental Energy, Wyoming Minerals and U.S. Steel, etc. The use of ammonium carbonates solutions, however, contaminates the formation and requires a time-consuming restoration operation. The other approach to reduce the permeability loss is to pretreat the sensitive formation with chemicals which prevent clay dispersion and migration. Such chemicals include hydroxy-aluminum (Reed, 1972 and Coppel et. al., 1973), hydrolyzable zirconium salts (Peters and Stout, 1977), hydrolyzable metal ions in general (Veley, 1969) and polyelectrolyte polymers (Anonymous). Still another approach, is to minimize the "shock" caused by sudden injection by gradually changing the chemical composition of the injected fluids from that of the formation water. THE APPROACH Since permeability loss can be an important factor limiting the efficiency and economic viability of the in situ leaching process, a study was initiated on

Jan 1, 1982

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By L. A. Roe, E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3; CaO: 48.30%, SiO2: 51.70%. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, CA. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, NY, was developed by the Cabot Corp. A processing plant was placed onstream in 1953, with nearly continuous production to date. It is currently operated by NYCO, a division of Processed Minerals, Inc. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1980, the United States was the major producing country, furnishing about 75% of the world&apos;s output. Current production comes from Finland, Mexico, India, and Kenya. Small amounts have been shipped intermittently from the USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and Namibia (South-West Africa). The principal use of wollastonite is in the manufacture of plastics. Other uses are for paints, ceramics, adhesives, fluxes, glazes, thermal insulation board, and refractory products. Mineralogy Pure wollastonite, CaSiO3, has the composition of 48.3% CaO and 51.7% SiO2. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mohs&apos; scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540ºC. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. The average diameter of wollastonite is 3.5 µm. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both, with colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The acicularity of wollastonite is a property of considerable importance to the marketplace. The plastics industry makes utilization of high aspect ratio grades of wollastonite (20:1) for reinforcing thermoplastics and thermoset polymer compounds. The naturally high pH of 9.9 (10% water slurry) is a prime property to the coatings industry. The coatings industry uses milled grades of wollastonite as a pH stabilizer in interior and exterior PVA and acrylic latex systems. Processed wollastonite can have a G.E. brightness of 90 to 93. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature

Jan 1, 1983

By F. E. Crane, J. Downie

The general application of Darcy&apos;s law to natural rocks has already been challenged in the literature.1 The evidence shows that the permeability as calculated from the Darcy equation can be a function of the pressure drop and the salt concentration of the water phase. Most explanations for aberrant behavior involve clays and their properties and have been qualitatively satisfactory.Recently, however, Odeh2 revived the theoretical views of Yuster.3 Since Yuster&apos;s concept implies a fundamental error in using Darcy&apos;s relationship for two-phase flow, and not merely that conditions may limit its use, Odeh&apos;s experimental support arouses considerable interest. However, Odeh&apos;s work as presented is thought to to be inadequate. He has omitted important information about his materials and procedures; therefore, acceptance of his conclusions should be withheld. Since a clay effect is possible, Odeh should have been allowed space to present a more detailed account of the rocks which he used and the precautions which he took to avoid confounding the effects of clay and fluid circulation. In addition, it follows from Odeh&apos;s discussion that the oil relative permeability should increase as the viscosity ratio increases. Odeh presents data corroborating this deduction. It also follows that the oil relative permeability should decrease as the viscosity ratio of oil to water decreases. However, our results show that a high relative permeability, when once attained by using a viscous oil, may be maintained when that oil is replaced by an oil of much lower viscosity. EXPERIMENTAL PROCEDURE The results are shown in Fig. 1 and were obtained as follows. Sandstone cores. 3-in. long X l-in, in diameter and which contained clays, were saturated with

By S. C. Sun

This article by Spokes and Mitchell de- serves high commendation. For many years mineral dressers have been at a loss to explain the variation in magnetic susceptibility of the same mineral species obtained from different localities. In fact, they do not even have a list of accurately measured data on the specific magnetic susceptibility of weakly magnetic minerals to consult. Experience as a university teacher has firmly convinced me that the average student has more difficulty in acquiring a satisfactory knowledge of magnetism than of any other branch of mineral dressing. This is almost entirely because the subject has been treated far too much from a strict practical standpoint and far too little from a fundamental one. It is no exaggeration to state that almost all the published theoretical discussions are based on the experimental results of manufactured chemicals and alloys, but not of naturally occurring minerals. In an attempt to remedy this state of affairs, the author of this article not only set up a new magnetic balance in the Department of Mineral Preparation of The Pennsylvania State University, but also performed work of fundamental value, thus pointing the way to further research. This is evidenced by the fact that an investigation of the magnetic susceptibilities of manganese minerals was recently completed by S. G. Watt under the direction of David R. Mitchell, now acting dean of the College of Mineral Industries of the Pennsylvania State University. D. J. Cook is studying the magnetic susceptibility of titanium minerals under my supervision. It is hoped that our research program can be continued for several years and that similar investigations will be Initiated at other universities and research institutions.

Jan 4, 1958

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.&apos; Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.&apos; Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1938

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee

Jan 1, 1943

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers &apos; and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1944

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given be- low. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1932

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given be- low. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1934

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given be- low. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1934

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1937

By Carl J. McHargue

Mechanical twins were produced in electron-beam melted columbium by high-speed impact at room temperature and by slow or fast compression at -196°C. The composition plane of the twins was { 112} and the shear direction was <111>. Notches in the twin bands often corresponded to traces of {110) of the matrix and appeared to be untwinned regions. Markings within the twin bands were interpreted as resulting from {110} slip in the twins. THERE has been much work in recent years concerning plastic deformation by glide, and the dislocation theory relating to glide has reached a relatively high degree of development. On the other hand, there have been fewer studies of deformation by mechanical twinning, and understanding of this process is far from satisfactory. This method of deformation is of interest for at least two reasons. First, it provides a mechanism in addition to glide for the relief of stresses, and, in the bcc and hexagonal close-packed metals may result in significant amounts of plastic flow. Secondly, there is the possibility that twins may act as barriers for dislocation movement, resulting in pile-ups which could nucleate cracks. As might be expected, the bulk of the literature on mechanical twinning in the bcc metals is concerned with iron. A good summary of the work done prior to 1954 is contained in the book by all.&apos; Recently the refractory bcc metals have become increasingly important. Limited studies have shown that tantalum,2,3 molybdenum,4,5 vanadium,6,7 tungsten,&apos; and columbium9-11 deform by mechanical twinning under some conditions. Alloys of molybdenum with rhenium and tungsten with rhenium show extensive deformation by twinning at room temperature.I2-l4 Most of these studies have dealt primarily with mechanical properties at low temperatures or have shown the existence of twins, and there is only a small amount of information concerning the conditions under which they form. The subject of the present paper is the formation of twins under stress in columbium with a consideration of their morphology. EXPERIMENTAL PROCEDURE The material used for these studies was taken from an ingot of columbium which had been melted twice by the electron-be am-method. The analysis of the ingot was (in ppm): B < 1, C = 10, Fe < 100, The cast ingot contained very large grains, and it was possible to obtain single-crystal prisms which measured from ¼ to 3/4 in. on a side. A few experiments were conducted on polycrystalline plate which was prepared by rolling material from the same ingot at room temperature and annealing at 1000 in a dynamic vacuum of 10-6 mm Hg. This gave a plate in which the grains had an average diameter of 3 mm. After the specimens were cut from the ingot, the six faces were metallographically polished and elec-tropolished to remove all traces of cold work. Most of the observations were made on the surfaces of the deformed specirllens without further treatment. Occasionally, etching after deformation was desirable. In these cases, an etchant of the composition 50 parts H2O, 5 parts HNO3 25 parts HF, and 10 parts H2SO4 was found to delineate the twins very well. Unless considerable care was taken to ensure the removal of all disturbed metal left by the mechanical polishing, etching failed to reveal many of the features discussed in this; paper. The specimen&apos;s were deformed either by impact or slow compression at 77°K (liquid-nitrogen coolant), 198°K (dry ice and acetone coolant), and 298°K. The impact load was delivered by a hammer except in one case where the load was delivered by a bullet. Slow compression was carried out on a hydraulic testing machine equipped with a chamber to hold the coolant. EXPERIMENTAL RESULTS It has been generally believed that the conditions favoring the formation of deformation twins are large grains, low temperature, and impact loading. In fact, Barrett and Bakish2 found twins in tantalum only after impact deformation at 77°K, and Adams, Roberts, and Smallman10 observed twins in columbium only at 20 For these reasons, the initial experiments of this study used impact loading. Hammer blows caused many bands resembling twins in single crystals a.t 77" but not at 198°K. Only a few slip lines were observed on any of the single-crystal specimens of this study—essentially all the deformation occurred by twinning. The appearance of the twins on the as-deformed surface is shown in Fig. 1. Although both Figs. 1(a) and l(b) are photomicrographs of twins taken at the same magnification and from the same crystal, they are startlingly different in appearance. Fig. 1(a) was taken from the crystal face approximately perpendicular to the shear direction, whereas Fig. 1(b) was taken from

Jan 1, 1962

By G. W. Josephson

Since the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,l and the large-scale expansion of the industry has taken place since 1900. Historical Background Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low- priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a high degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun&apos;s rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof—conservatively, 500 per cent. Slate Graftules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate Pro-

Jan 1, 1948

By G. W. Josephson

Since the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,l and the large-scale expansion of the industry has taken place since 1900. Historical Background Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low- priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a high degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun&apos;s rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof—conservatively, 500 per cent. Slate Graftules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate Pro-

Jan 1, 1948