Search Documents

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

The question, Who won the war?, has been the text for innumerable newspaper, and magazine articles, the answers running from "bread and butter" to "poison gas," in a material sense, and from the "Y. M. C. A." to the "boys in the front lines," humanly speaking. Personally, I think the margin by which success was secured was so narrow that none of the complex, interdependent factors could have been .spared, and that, as Admiral Sampson said after the battle of Santiago: "There is glory, enough for all." But if any one human factor can be said to have been absolutely indispensable, I think all will agree that it was the engineer. The engineer, as a rule, is a modest fellow, so modest in fact and so averse to publicity of any kind that, referring to him as a class, he was hardly occupying the place he should in public estimation before the war. By way of illustration, in the early history of a mine in Bisbee, the chief owner was also the proprietor of a saloon and spent most of his time there. When asked why he did not pay more attention to the mine, lie replied: "Oh! I can hire a boy to look after that; it takes a man to run this bar." Comparisons of the position and pay of engineers with other occupations are sometimes made to show that the engineer is not getting all that he should, considering the time of preparation and the qualifications required. Perhaps at least a part of the cause may be his aloofness from many of the practical affairs of everyday life. Whether he won the war or not, the part played by the engineer has certainly placed him on a sort of pedestal in the public estimation at present and it is very desirable to keep him there and maintain the position he has made for himself.

Jan 9, 1919

By Herbert A. Franke

ANY analysis of the aluminum situation, particularly of the factors involved in the current shortage of the metal, must consider the rapid march of events since the Munich fiasco of September 1938. At the end of 1938, the sole domestic producer of aluminum had more than a year's supply of metal on hand, having added 50,500 tons of output to stocks during the year. Not until war had been declared between the United Kingdom and Germany in September 1939 did the United States begin to make serious preparations for defense and a limited national emergency was proclaimed. Congress reflecting popular opinion, was not disposed to spend huge sums for armaments in 1939, and although 31,413 tons of aluminum was withdrawn from stocks. 107,500 tons was still on hand at the end of the year. When the President initiated a 50,000-airplane program in May 1940 the country was astounded, as previous Congressional authorizations of approximately 6000 planes for the Army by July 1911 and 3000 for the Navy by 1914 had been considered adequate.

Jan 1, 1941

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By C. S. Sivil

To modern civilization the platinum metals are of inestimable value. Their distinctive properties, both physical and chemical, render them indispensable in an age in which the processes of the laboratory are becoming an essential part of the daily life of the world. Generally, their function, though vital to particular processes, is not spectacular, and so remains unknown to all except the operators. EARLY METHODS OF MANUFACTURE The properties of platinum were recognized as of prime importance for scientific work at. a very early date, probably between 1750 and 1760. The difficulty of making articles from it seemed almost insurmountable, because no means of attaining the temperature necessary to melt it were known at that time. It is true that solid platinum could be obtained by fusing the metal with a more volatile metal such as arsenic, which was subsequently driven off by baking, but such a method, at its best, would give only a very brittle product, which was totally unsuitable for the purposes for which it was intended. Little, if any, progress could be made until it was discovered that platinum sponge, heated to white heat and hammered in an iron or clay mold, would metallize and retain the shape of the mold. This was a process that could not be wholly satisfactory but from it developed the method of pressing the sponge in a mold and forging it at white heat into wire or sheet. At present a somewhat similar process must be used for fabricating articles of tungsten, molybdenum and other metals of high fusing point, as with these metals we face today the same problems that the scientists of the eighteenth century encountered with platinum, but possibly the next significant advance in the metallurgy of these metals will be the devising of means to melt and cast them.

Jan 1, 1931

By David A. Summers, John Corwine, Li-King Chen

The results from fracturing plexiglas beams are combined in eight existing equations to determine the surface energy of the material. The reliability of each equation is tested, and the equation in use to determine fracture toughness is found to be the most exact. This equation is then used in determination of the surface energy of Barre Granite.

Jan 1, 1971

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By Albert R. Ledoux

With the improvements in design and efficiency of machinery the element of danger in its use is becoming less, but it is a question whether the strain involved in operating modern plants is not increasing somewhat the danger of accident due to human fallibility. I propose to describe a somewhat uncommon casualty resulting from a not infrequent incident in the use of air-compressors. It is not necessary to state the location of the mine in which the accident occurred nor the makers of the compreseor, and the object of this brief paper is more to draw out suggestions from members more familiar than am I with the practical handling of mining machinery, than to point a moral. The compressor in question was a three-drill machine of standard make. At the time of the accident it was furnishing air to a single drill working in an upraise from a well-ventilated tunnel, and giving ventilation to a winze below the tnnnel where two men were hand-drilling. The compressor also furnished power to a small hoist in the winze, but the hoist was only operated occasionally, and never while the drills were working. The drills were located about 1200 ft. from the compressor. The engineer testified that he never had been short of air, and that there had been no complaillts that the

Jan 1, 1904

By K. Huessener

This paper attempts a survey of the principles involved in the combustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years1 practical working experience as combustion engineer, which I trust will prove useful to my readers. HlSTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow, The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam, The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 1, 1916

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,&apos; in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By Ralph B. Stevens

INTRODUCTION Underground fires continue to be one of the most serious hazards to life and property in the mining industry. Although underground mines are analogous to high-rise buildings where persons are isolated from immediate escape or rescue, application of technology to locate and control fire hazards while still in their controllable state is slow to be implemented in underground mines. Even in large surface structures such as hotels, often only fire protection systems which meet minimal laws are implemented due to the high cost of adding extensive extinguishing systems, isolation barriers, alternate ventilation, escape routes and alarm systems. Incomplete and ineffective protection occasionally is evidenced where costs would not seem to be a factor, such as the $211 million MGM Grand Hotel fire November 21, 19801. Paramount in increasing fire safety and decreasing the threat of serious fire is early warning followed by proper decision analysis to perform the correct action. However, very complex fire situations can be produced in structures such as high-rise buildings and underground mines simply because of the distances between the numerous fire-potential locations and fire safe areas. Other complexities arise when normal activities occur that emit products of combustion signaling a fire condition to a sensitive fire/smoke sensor. For example, the operation of diesel equipment or the performance of regular blasting can produce combustion products that reach the sensitive alarm points of many sensors2. Smoke detectors for surface installations provide fire warning when occupants are at a distant location or when sleeping, thus greatly reducing injuries and property damage. However, when installed in the harsh environments of underground mines, fire and smoke detection equipment soon becomes inoperative, unreliable, or requires excessive maintenance. The U.S. Bureau of Mines has performed many studies and tests to improve fire and smoke protection for underground mine workers3. This paper describes several USBM safety programs which included in-mine testing with mine fire and smoke sensors, telemetry and instrumentation to develop recommendations for improving mine fire safety. It is hoped that the technology developed during these programs can be added to other programs to provide the mining industry with the necessary fire safety facts. By recognizing fire potentials and being provided with cost-effective, proven components that will perform reliably under the poor environmental conditions of mining, mine operators can provide protection for their working life and property equal to that which they provide for themselves and their families at home. The basis of this report is two USBM programs for fire protection in metal and nonmetal mines4,5 and one coal program6. The data was collected beginning in May 1974 and continuing through the present with underground tests of a South African fire system installed at Magma Mine in Superior, Arizona, and a computer-assisted, experimental system at Peabody Coal Mine in Pawnee, Illinois. The conduct of each program was as follows: • Define the problem and its magnitude in the industry • Develop concepts to solve or diminish the problem • Review available hardware or systems approaches to fit the concepts • Install and demonstrate the performance of a prototype system through fire tests in an operating mine. MINE FIRE FACTS Whether in coal or metal and nonmetal mines, the potential severity of fire hazard is directly related to location. As shown in Figure 1, fire in intake air at zones A, B, C or D can cause contamined air to route throughout the mine quickly if not detected, isolated or rerouted. Causes and location of former metal and nonmetal fires are represented in Table 1; the cause and location of fatalities and injuries is shown in Table 2. Coal-related fires and their impact on deaths and injuries are graphed in Figure 2; their locations are described in Table 37. Significantly the table shows that the hazard to personnel was three times greater for fires occurring in shaft or slope areas, and the percentage of deaths and injuries was four times that of other areas. Number of Persons Affected A 129-mine sample indicated that from 8 to 479 employees per shift work in underground metal and nonmetal mines, and that deeper mines have larger populations, as shown in Figure 3. Coal mining relates similar employment, and a 16-state sample of 670 mines employing at least 25 persons shows the distribution in Figure 4. Drift mines accounted for 58 percent of the sample but employ only 45 percent of the underground workers.

Jan 1, 1982

By Thomas Leonard Watson

I. HISTORICAL. BARITE has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. GEOGRAPHICAL AND GEOLOGICAL DISTRIBUTION. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State-namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties:, Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties-Bedford, Louisa, Pittsylvania, Russell, and Tazewell-but in the first two counties named there was no production, the work being solely development.

Jan 9, 1907

By H. Leslie Bullock

From aluminum to zirconium, the quantitative preponderance of quartz as a gangue material is well recognized. lf this material is to be efficiently removed, its variations must be understood. Variations with temperature are especially important. Too little attention has been given to the thermal polarization of quartz. Under closely controlled conditions, electrostatic upgrading is very reliable. For efficient separation, contact charges must be fostered and charges due to radiation, surface coatings, or thermal polarization avoided. This paper lists thermal transition points of quartz and shows their effect on actual separations. Simple separation tests with all factors except temperature held constant are recommended for determining transition points. With silica making up more than 27% of the earth&apos;s crust, its oxides comprising more than 59% of all igneous rocks, and quartz accounting for most of the main free oxides, the mining engineer is in constant contact with quartz, which may occur as a valuable mineral to be purified or, far more frequently, as a gangue material to be removed as completely and economically as possible. As a means of effecting such purification or removal, dry beneficiation is becoming more and more desirable owing to local water scarcities, wet waste disposal problems, or freezing conditions. One method that has been gaining particularly rapid acceptance is electrostatic beneficiation, or the separation of dry free-flowing materials by means of opposite surface charges, differences in potential, or differences in conductivity. Electrostatic beneficiation dates back to the 1870&apos;s, but only in recent years have newly developed methods and apparatus and a growing knowledge of solid-state physics widened the field for its economical application. Because the term "electrostatic beneficiation" has been rather loosely used in the literature, it has come to include both electrostatic and electrodynamic procedures. Attracting type separators, however, in which oper- ation is based on differences of surface charge or potential, are truly electrostatic, because the separation occurs in a substantially static field set up between oppositely charged surfaces. Separations with this type of equipment may occur at potentials as low as 1000 v and seldom require potentials as high as 30,000 v. In the new contact charge dielectric separators1 the variation in charge is produced by continuous contact and separation of the particles in the moving feed stream and these charges are fostered by the use of non-conducting support and feed surfaces and by handling the feed in the form of streams of appreciable depth. This favors uniformity of feed and allows higher production rates. The distinctive surface charge differences are set up on the separation of the particles according to Coehn&apos;s Law,2 which states that equal and opposite charges are generated on the separation of any two materials in contact and that the substance having the highest dielectric constant will be positively charged. The basic contact charge concept is reliable, but all electrical charges are transient and modified by the electrical conditions of the surroundings. Pyro-electric, photoelectric and radiant effects may modify or totally destroy the contact charges necessary for efficient separation, or contact with conducting surfaces may neutralize them. Such hostile conditions must be carefully guarded against, since they have led to many costly failures in the past. The most consistent difference in surface charges to insure good separation is produced by repeated uniform contact and separation of particles in the moving stream. The thickness of the feed stream possible with this method reduces the effect of contact with the supporting surfaces, but as some contact is inevitable, the best results may be assured by having the dielectric constants of the supporting surfaces between the dielectric constants of the substances to be separated. In general, the hard smooth surface of quartz makes it an ideal substance for electrostatic separation from most minerals. For instance, with calcite, starting with a feed containing 1.9% acid insolubles, one can produce a concentrate containing 0.30% acid insolubles with a tailings containing 21.7% acid insolubles and a yield of 92.8%. The color can be held at 92 or above and the tint at 1.7 or lower. Working with specularite iron ore, laboratory work has given a concentrate of 68.8% Fe., with an iron unit recovery of 96.7%. Excellent results are also in pros-

Jan 1, 1969

By E. W. Engelmann

A NEW and interesting type of drier has been developed and operated at the Magna plant of the Utah Copper Co. for the past year for the drying of a filtered concentrate in the molybdenum recovery plant of this company. The several units installed have ranged from 12 to 30 in. in width, and from 14 to 30 ft. long. Their economy was immediately apparent after the first one was installed. The machine is not only low in capital cost, but has proved efficient for the drying of fine concentrate at low operating cost. The Utah vibrating drier consists of a steel conveyor trough supported on flexible reeds from a structural steel foundation anchored in concrete. The steel pan, which is also the drying surface, is vibrated by a heavy Utah electromagnetic vibrator fastened either to the head or discharge end of the pan. The vibration thus obtained agitates the material and causes it to be conveyed over the heated surface.

Jan 1, 1938

By L. Hartsell Cash

INTRODUCTION Created in 1944 to help rebuild those economies, principally in Europe, which were seriously damaged or destroyed during the Second World War, the World Bank--or to use its correct name, the International Bank for Reconstruction and Development-began its operational phase by making a loan to the Government of France to accomplish two tasks: (i) to import coal for space heating purposes; and (ii) to buy new machinery and equipment to help rehabilitate its coal mines. Once the thrust of reconstruction in postwar Europe was largely accomplished, the World Bank Group (for today the World Bank has three separate lending windows) turned to mobilizing funds to improve living standards in developing countries, which remains its primary goal today. Over this period of time, the World Bank Group has continued to assist the world mining industry in various ways and, since 1955 the World Bank Group has financed mining or mineral processing projects with loans/credits totalling $1.5 billion. The World Bank Group consists of two institutions--the World Bank itself and the International Finance Corporation (IFC), which was founded as a separate institution in 1956 and three separate lending windows--the World Bank, the International Development Association (IDA), and IFC. The World Bank loans are provided at commercially-related interest rates but have grace periods usually of up to 3 to 5 years and repayment periods ranging from around 15 to 20 years. Since the World Bank raises its operating funds on the international capital markets in varying currencies and in varying interest rates, it relends a basket of currencies at floating interest rates which are fixed every six months to reflect the Bank&apos;s own borrowing cost. At the present time, the interest rate is just below 10% per year and in addition, a one-time front-end fee of 1/4 of 1% is charged. Also, a commitment fee of 3/4% per year is charged on the undisbursed amount of the loan itself. For loans to industrial and mining projects, it is normal to charge an additional guarantee fee of 1 to 1.5% in addition to the annual interest rate. This guarantee fee is payable to the government of the country in which the project is carried out since, by its charter, the World Bank is required to have the guarantee of the host government for each loan made in a specific country. By far the greatest source of lending funds within the World Bank Group is that of the World Bank itself and for the fiscal year ending June 30, 1984, the World Bank approved loans totalling $12 billion. The second lending window within the World Bank Group is IDA which performs the same functions as the Bank itself and has the same staff. Nevertheless, its loans (called credits) are made on much softer terms and are made to the poorest nations only. IDA funds are subscribed by the wealthier countries, usually as grants, and these are relent as credits to those countries with the lowest per capita income. IDA credits are made for 50 year periods, including 10 years of grace, to the government itself. The credits are interest free, but there is a service charge of 3/4% per year on the amount withdrawn and outstanding to defray the administrative costs of IDA. Credits approved during fiscal 1984 totalled $3.5 billion. The third lending window is IFC. While IFC is a separate corporation and operates quite separately from the World Bank and has its own staff and regulations, it works very closely with the World Bank on its overall approach to the mining sector and to a particular country. IFC&apos;s mission is essentially to supply venture capital and to stimulate development of the local private sector in capital markets as well as to promote the international flow of private capital to developing countries. Unlike the World Bank and IDA, the IFC does not lend directly to governments

Jan 1, 1985

By D. J. Carney, J. Chipman, N. J. Grant

An absolute calibration has been achieved for sampling and analyzing liquid steel for hydrogen based on Sieverts&apos; values of hydrogen solubility in iron. Further checks were made in nickel, iron-nickel, and 18-8 stainless melts. The sampling method was successfully applied to a large number of commercial steel melts in various types of furnaces. The concurrent problem of sample storage was also solved. THE problem of sampling of liquid steel for hydrogen is more difficult than the problem of analysis. Hydrogen has a greater mobility than any other element; it is the only element that will diffuse out of steel at room temperature. In accordance with the known relation between temperature and diffusivity, the diffusion of hydrogen is extremely rapid at the temperature of liquid steel. Consequently, in the past, attempts to quench molten steel to retain the dissolved hydrogen have not been as successful as similar attempts with nitrogen or oxygen. The retention of hydrogen is especially difficult since it will continue to escape at room temperature even if the molten metal has been rapidly quenched. The hydrogen sampling methods may be classified broadly as (1) the rapid quenching techniques which attempt to preserve super saturation and (2) those methods which attempt to collect the gases evolved as the metal freezes and cools to room temperature. With all methods of sampling but especially with the rapid quenching methods, there is also a concurrent problem of storing the sample until analysis is undertaken. The two problems are interrelated and must be considered together when discussing liquid steel sampling techniques. The major obstacle in liquid steel sampling has been that there was no way of evaluating properly the various sampling and storage techniques which have been developed. It has not been possible to compare the accuracy of the various methods. For evaluation of sampling methods some known standard is required; this may be found in the published work on the equilibrium solubility of hydrogen in liquid iron which has been determined in three separate investigations.1,2,3 The data are shown in table I. Sieverts&apos; original method of obtaining gas solubilities involved measurement of the volume of gas required to saturate the liquid metal contained in an evacuated bulb of known volume. This procedure, improved by introduction of high frequency induction heating, has yielded reproducible results which appear to be entirely dependable. Using Sieverts&apos; method, it has been proved for iron and other metals and alloys that the hydrogen solubility is proportional to the square root of the pressure of the hydrogen gas above the liquid, so that one may work with various partial pressures of hydrogen to put different amounts of hydrogen in solution. From Sieverts&apos; law it is possible to know accurately what amount of hydrogen is dissolved in the liquid metal at the time of sampling. The accuracy of a sampling method may be gauged by reference to this known solubility. It was the purpose of this investigation to develop a method for sampling liquid steel and for storing the sample so that the analytical result would represent the actual hydrogen content of the metal bath. For this purpose an induction furnace was

Jan 1, 1951

By Reginald S. Dean

THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these &apos;requirements. Other hereto-fore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filterable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and C02, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores; including Three Kids, Artillery Peak, Cuyuna, and Chamberlain; as repre-

Jan 1, 1952

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien&apos;s Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?&apos; In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.&apos; occurred, data were combined.

Jan 1, 1958

By W. G. Jewitt

YELLOWKNIFE, the most northerly Canadian gold mining district, is once more in the throes of a boom. Touched off by spectacular and well-publicized diamond-drilling results on the property of Giant Yellowknife Gold Mines, Ltd., mining companies and the general public are competing for mining claims and for the shares of companies owning mining claims in the area, with little regard for values. Such a stock-market boom has various unfortunate consequences but undoubtedly one beneficial result is that considerable amounts of money are made available for serious development. The Yellowknife mining area lies on the north shore of Great Slave Lake, in the Northwest Territories, at a latitude of approximately 62°30&apos; north. The topography is a low-relief phase of that usual in the Canadian Laurentian shield. Roughly, one third of the surface is lake-covered, one third muskeg or overburden, and one third is bare

Jan 1, 1944