Search Documents

By James R. Garvey

Coal reserves of the United States are enormous. Considered on the basis of proven reserves, and compared with reserves of other fuels, coal constitutes 88% of the proven recoverable energy resources of the nation. That includes oil, natural gas, oil shale and uranium used in burner reactors. Considered on the basis of "ultimate recoverable reserves", that is, those resources which can be extracted with improved technology and at somewhat higher costs and including those resources of all fuels not yet found but believed to be waiting discovery, coal still accounts for 75 % of the national total. In the U.S. hydrocarbon economy about 76% of the total energy needs are supplied by petroleum and natural gas and about 20% by coal. Domestic resources of oil and gas are running dangerously low, and assuming a continued hydrocarbon economy, the 20% supplied by coal may increase dramatically. Nearly a quarter of the petroleum consumed in the U.S. is imported. Natural gas is in shorter supply than petroleum and the problems of its importation seem at least as difficult as those of oil.

Jan 6, 1972

By John Dasher, M. C. Chang

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to beneficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly -24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant.

Jan 3, 1959

By J. R. Thoenen

THE proper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical con-troversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of under-ground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute TRANSACTIONS, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in MINING AND METALLURGY in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical:

Jan 1, 1935

By G. L. Coleman, D. S. Hutton, W. C. Leslie

The occurrence of twins in a iron, generated during cooling through the ?-a transformation, is well established,1-8 but this phenomenon has been nearly ignored during the past 20 years. It is the purpose of this note to call attention to the prevalence of such twins and to illustrate their appearance. The work of paxton7 and Kelly8 has demonstrated beyond reasonable doubt that for Neumann bands (mechanical twins) in a iron the twinning plane is (112) and the twinning direction <III>. The agreement with McKeehan&apos;s earlier work4 on transformation twins indicates that both types of twins in ferrite follow the same twinning law. There is little doubt of this conclusion, but it could be strengthened by a microbeam X-ray determination of the orientation relationship between a single ferrite grain and a transformation twin within that grain, as in the technique used by Kelly8 on Neumann bands. RESULTS AND DISCUSSION Transformation twins, identified by their appearance on a polished and etched section, were found in

Jan 1, 1960

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to l000ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1980

By H. Colijn

Belt scales are frequently used in the mining industry because of the ability to handle large tonnages without interrupting the material flow, fitting easily into all types of bulk handling systems and being relatively inexpensive. Although manufacturers claim weighing accuracies better than Y2%, many operators experience, in practice, much larger errors and they have become apprehensive about the use of belt scales. However, in spite of these disappointing instances, a belt scale is one of the most valuable tools for process and inventory control. Since it is a measuring device, care should be given to the design and installation of belt scales. The basic components of a belt scale are: (1) conveyor belt, (2) scale suspension, (3) sensing device, (4) integrating and recording. The first component of this system is of great importance to the overall accuracy and has been thoroughly discussed in earlier papers. This paper will review primarily the various scale hardware designs currently available, and will be confined to the last three components of the system.

Jan 1, 1973

By William G. Schultz

Sylvite of Canada, a division of Hudson Bay Mining and Smelting Co., operates a new 8500-tpd potash mine ten miles northeast of Rocanville, Sask. This mine, employing less than 60 men in its underground maintenance, engineering, and production operations probably ranks as one of the most highly mechanized and automated mining operations in the world. Access to the flat lying potash bed is through two 16-ft-diam concrete and steel lined shafts 3300 ft deep. The backbone of the operation is two 258-ton, 1500-hp continuous mining machines capable of mining in excess of 700 tph per machine while employing extensible conveyors for haulage. This production capability is complemented by a completely automated haulage, storage, and hoisting system. Of the other unique features of this operation, the principal ones are that the mine was designed and developed by the people that are currently operating it and from the time the shafts were commissioned, the mine was completely developed, equipped, and brought to full production in less than six months.

Jan 1, 1974

By Charles Prasky, Robert K. Zahl, John C. Nigro

Bench scale and pilot plant research was conducted using dolomitic (CaO - MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.5% SiO2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1200° to 1250°C appeared to be the most favorable for production of self-fluxed pellets with basicities (B) above 1.0. Comparison of the mechanical and metallurgical properties of regular (acid) and self-fluxed pellets (B = 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the selffluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The +3 mesh Linder index increased from 68% (regular pellets) to over 90% (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1974

By M. G. Cheney

THE production record of the Sinclair-Moren pool, in southeast Young County, Texas, demonstrates that under efficient operating methods a single well may obtain normal oil recovery from an area of 100 acres or more. This record is the more surprising in view of relatively adverse reservoir conditions such as lack of water drive, moderate initial reservoir pressures and a consolidated sandstone reservoir with original permeability greatly reduced by processes of lithification. This case history is considered worthy of special study in view of the ever present problem of proper spacing of wells. Cupidity, abetted by the unrestrained law of capture, has in too many instances guided development and production methods without regard for sound economic and engineering principles. Largely as a result of ill advised spacing of wells, many oil fields have brought financial losses instead of deserved profit to those using capital, time and energy in this important business of adequately meeting the petroleum requirements of what is known as our modern civilization. In March 1923, the Sinclair Oil and Gas Co. obtained initial daily production of about 12,000,000 cu. ft. of gas and 1100 bbl. of oil in its first well near the center of a 372-acre lease on the L. P. Moren land, James Rose survey, Abstract 245. This exploratory test was drilled as a geological prospect of average promise, on a plunging anticline with possibly 10 ft. of closure as mapped on the outcropping limestone of upper Canyon (Pennsylvanian) age. In subsurface, the top of the producing res-ervoir is 16 ft. lower in this well than in the highest wells but probably 25 ft. above lowest closing contour. Wells No. 2 and 3 were drilled about 1/4 mile west and southwest near a normal fault with some 30 ft. of downthrow to the southwest. The producing sand was reached at a depth of 2512 ft. and drilled to 2529 ft. in the first well. This sandstone reservoir is of Millsap Lake (middle Strawn, upper Cherokee) age. It was absent in the second and third wells, which were abandoned at the depths of 3725 or more. In April 1925, a fourth well was drilled 600 ft. east and 24 ft. lower for top of sand than No. I. Production of about 100 bbl. daily was reported from 2521 to 2562 after an 80-quart shot. This well was drilled to 4560 ft., plugged back to 2575 and shot again; but was abandoned soon thereafter because of small production.

Jan 1, 1940

By Kendall E. Born

Production of crude oil in Tennessee during 1943 was approximately 8200 bbl., slightly less than the 1942 production, Counties. Some half dozen wells in Clay, Fentress, and Pickett Counties, pumped intermittently, produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The Morgan County production was about I0,000,000 cu. ft. and approximately 8,000,000 cu. ft. was produced from the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Thirteen wells were spudded during the year; three were drilling on Dec. I, 1943. Of the nine completions, representing 10,488 ft. of hole, three were gas&apos; wells of commercial size although only one of them has been placed on the line. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Pluteuz.-There were three completions in the northern part of

Jan 1, 1944

By Kendall E. Born

Production of crude oil in Tennessee during 1943 was approximately 8200 bbl., slightly less than the 1942 production, Counties. Some half dozen wells in Clay, Fentress, and Pickett Counties, pumped intermittently, produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The Morgan County production was about I0,000,000 cu. ft. and approximately 8,000,000 cu. ft. was produced from the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Thirteen wells were spudded during the year; three were drilling on Dec. I, 1943. Of the nine completions, representing 10,488 ft. of hole, three were gas&apos; wells of commercial size although only one of them has been placed on the line. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Pluteuz.-There were three completions in the northern part of

Jan 1, 1944

By F. M. Lewis, J. E. Goodman

TENNESSEE Copper Co. operates two ore concentrators, the London and Isabella mill. Copperhill, Tenn. In 1948 and 1949 the small ball mills and rake classifiers in the London concentrator were replaced by one large ball mill and one hydraulic classifier. This new ball mill was designed oversize so that it could be operated at slower than normal speed. The proper operating conditions were established and the results published.1 Later it was found that this mill operated more efficiently with a small ball charge.2 While this London grinding practice was being developed, the Isabella grinding circuit was not changed in any way. It remained a conventional two-stage rod mill-ball mill combination, the rod mill in open circuit and the ball mill in closed circuit with a rake classifier. Study of the data indicated that grinding cost could be lowered by converting to the London practice, but not enough would have been saved to warrant the expense of converting. No plan for improving this grinding operation could be developed.

Jan 11, 1957

By Alexander Sutulov

The Western industrial nations are facing today what can be defined as a gradual takeover of their investments in the developing world and more importantly, they are beginning to feel approaching problems with their adequate raw materials supply. This puts them into a strategically hazardous situation, which years ago would probably have been solved by conventional wars. However, the present political and military situation, and particularly the development of nuclear arms, makes such confrontations almost impossible or at least extremely dangerous. Thus other peaceful and more pragmatic solutions should be sought. This is particularly important because the present supply-demand situation in raw materials has a very strong political and ideological background. In the ultimate analysis there are two economic systems, that of free enterprise and the other of the collective or socialistic ownership. Both are competing for world domination, and it seems that both are eager to prove their advantages to the yet uncommitted Third World, which commands the great majority of the human race and a large part of its natural resources.

Jan 7, 1974

By Arthur H. Leigh

Anode mud, the residual material collected from the bottom of the electrolytic cells during the refining of copper is leached, roasted, fire-refined and cast into Dore1 metal anodes. Dore1 metal is a gold-silver-copper alloy containing 80 percent silver. The metal is processed electrolytically using the Moebius system to refine silver and separate gold, platinum and palladium. The Moebius cell cathodes receive a deposit of silver crystals which are melted and cast into 1000 ounce silver bars with 999 Fine minimum purity. Gold mud is collected in fabric bags and cast into gold anodes for further refining in the Wohlwill cells. Wohlwill cells are unique in that gold, the noble metal, can be put into solution electrolytically without the use of aqua regia. Gold is collected on high purity gold foil cathodes and cast into 400 ounce bull ion with 999.7 Fine minimum purity. Platinum and palladium remain in the electrolyte progressively increasing in concentration and are finally separated and purified by precipitation.

Jan 1, 1973

By David B. Campbell

Production of both metallurgical and thermal coal represents a significant sector of the mining economy of British Columbia. The coal measures are located in the Rocky Mountains, and the majority of the coal is produced by open pit mining. The coal seams occur interbedded with siltstones, sandstones, mudstones, and shales. Consequently, large volumes of waste rock are generated in the course of open pit mining. The waste rock is consigned to waste rock piles that of necessity must be developed on moderate to steeply sloping terrain. Some of the waste dumps currently under development will ultimately contain in excess of 500 million cubic meters of material, and some of the proposed waste piles will attain heights in excess of 300 m. These waste piles must be developed in a manner that will assure their stability through all stages of development, as well as over the long term after mining operations have been completed. This paper describes methods of waste dump development, factors affecting stability, modes of potential failure, and a simple method for monitoring movements to provide a warning of pending unstable conditions.

Jan 1, 1985

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........&apos;.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By J. H. Craig

As a result of information that the Navy Department was questioning the advisability of raising the maximum allowable exposure temperature for zinc-coated steel parts from 500 to 750 F., it was decided to make a series of high temperature tension tests on several types of uncoated and zinc-coated steels. The objective was to determine at what temperature intergranular penetration of galvanized steel by zinc might take place under conditions of rapidly applied stress and temperature. Tests were conducted in the range from room temperature to 1400 F. In this range, low-carbon and high-carbon steels did not suffer any adverse effects due to zinc coatings. In fact, at 1400 F. the zinc coatings appeared to have a beneficial effect. In stainless steel, the coating had no effect up to 1000 F. Above this temperature, the zinc coating appeared to cause a marked loss in ductility and a less pronounced loss in strength. There was no visible evidence of zinc penetration of the stainless steel structure, but it was assumed that this was the cause of the adverse effect.

Jan 1, 1945

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

Nebraska has never produced coal in any amounts, nearly all of its mining having been by farmers for their own and local use from very thin seams. Tonnages given in Table 73 are estimates. [ ]

Jan 1, 1942