Search Documents

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation. The Southeast Missouri lead belt is a mining district located about 65 miles south of St. Louis. This district is roughly 6 miles wide and 10 miles long. The ore horizon lies about 400 ft below the surface where most of the ore is mined from flat-lying beds of dolomitic limestone. This paper deals with the central part of the district, namely, that portion which contains a group of interconnected mines all in a central haulage system, serving four hoisting shafts. The two major hoisting operations are carried out at Federal No. 17 shaft and Leadwood No. 12 shaft. No. 17 accounted for about 70 pct of the ore hoisted in the district during 1950, averaging about 14,000 tons per operating day. The underground dumping and skip-pocket system at this shaft is similar to those of the other shafts except that it has two rotary dumps. The other ore-hoisting shafts have only one. It might be mentioned that waste rock is hoisted at still other shafts, hauled off, and dumped on the surface by trucks. The hoisting shafts are on a connected system of about 200 miles of underground 24-in. gage main line railroad. There is also the Bonne Terre system, with its own ore-hoisting shaft, which consists of 13.5 miles of 24-in. gage main line, located in the extreme north portion of the lead belt area. Smaller outlying mines such as Doe Run No. 12 and Hayden Creek operate on trackless or shuttle car haulage. In addition to the system of main line haulage, each contributing mine group has its own extensive system of stope or heading railroad. Trackless mining is making considerable headway in the Lead-wood and Desloge mines. Here the shovel loads into a shuttle car which in turn dumps into mine cars spotted on the main line track system. When the merits of underground haulage and surface transportation are compared, it must be remembered that in early days there were many individual

Jan 1, 1954

The importance, validity, and acceptability of the Paley Report has become the great issue of the minerals industry. A 12-man panel made up of representatives of various facets of the industry sat down at the 1952 Mining Congress Show in Denver in an attempt to clarify the many opinions currently held concerning the report. Howard Young, deputy administrator of the Defense Materials Procurement Administration, noted that the report had caused more discussion and serious thinking than any other government report, He did not subscribe to the "have not" principle, however, but called it a "need more" principle. Horace M. Allbright, president of U. S. Potash Corp., believes industry should continue to develop the report. He cited the editorial appearing in the September, 1952 edition of Bining Engineering,,, "Don't Let It Die," as expressing his feelings. Edward Snyder, president of Combined Metals Reduction Corp., says the statistics used in the report were used to promote a false international policy. He sees the report as a master plan for the development of the superstate. He also stated that the-ore reserves given in the Pales, report represent only 10 pct of what is actually available.

Jan 1, 1952

By V 7. 0 / 300 dpi

DRILLING in the Oligocene potash basin of Alsace prior to 1927 had shown important differences of level in the salt beds thus encountered. To explain this a somewhat unsatisfactory hypothesis of faulting had been advanced. During the latter part of 1926 and the beginning of 1927- our firm was engaged by two organizations for the purpose of trying to supplement, by an electrical survey, the geological data thus far collected. As a re-sult of this exploration it was possible to affirm that salt dome structures were present in the Oligocene basin of the Upper Rhine, something heretofore absolutely unknown in that region. Two salt domes were actually outlined, one, near Meyenheim, was made the subject of a communication to the Academy of Sciences, by G. Friedel2; the other, near Hettenschlag, was briefly dis-cussed by C. and M. Schlumberger3 before the same academy. The purpose of this paper is to indicate the strati-graphic and structural conditions of the area where these salt domes were found; to discuss the results of the electrical survey which led to the location of the domes, and indicate the new geological outlook which such a discovery suggests.

Jan 9, 1928

By Audley H. Snow

The general drift of the discussion as to the relative merits of pressure- and exhaust-fans has resulted, if we may judge from the prevailing practice, largely in favor of the latter. The subject has been hitherto treated, however, with special reference to highly gaseous mines, the effect of the form of ventilation upon dust-explosions having been too little considered. Even in mines containing practically no gas, dust-explosions may occur; and if, as I believe, pressure-fans are to be preferred for their effect upon dust, it may be worth while to reopen the debate, and to challenge the advisability of exhaust-ventilation under certain conditions. There are several forms of colliery-ventilation, which may be described as follows: Plain or simple pressure-ventilation, in which the fan acts as a pressure-fan, and the movement of coal is unobstructed at the surface by doors or equivalent devices in drifts or shafts, the traveling and haulage. thus being in the return-current. Plain exhaust-ventilation, in which the fan acts as an exhaust-fan, the movement of coal being likewise unobstructed at the surface, and the traveling and haulage being in the intake.

Jan 1, 1910

By M. Stuart, R. F. Down

The Copper flotation concentrate produced at Gortdrum mines contains about 1% Hg. This article deals with the treatment used to produce a substantially mercury-free copper concentrate. Metallic mercury is a byproduct. Nearly all the mercury in the Gortdrum concentrate is present in the copper mineral tennantite-tetrahedrite. This mineral is variably distributed throughout the ore body so that by selective mining it was possible to produce salable concentrate relatively low in mercury while the treatment plant was being built. Roasting was the only feasible method found for removing the mercury from the concentrate, and it was decided that this should be done in an atmosphere with limited oxygen. A multiple hearth furnace is used. Mercury soot is condensed from the gas stream and treated to produce prime virgin mercury. Problems were experienced at first with materials handling, oxygen control, cooling of the calcined concentrate, treatment of the mercury soot, and in the metallurgical accounting. Precautions were necessary to avoid health problems. The plant is now operating reasonably well. The value of the mercury produced does not warrant the cost of the plant but without it, the copper concentrate could not be sold.

Jan 1, 1975

By G. E. Agar, A. L. Mular

G. E. Agar (Manager, Minerals Processing Research, International Minerals & Chemical Corp., Skokie, III.) — The author notes a discrepancy between the parameters a and ß which are the slopes of the size distribution and energy-size modulus plots respectively. The reason for the discrepancy and the systematic decrease in the magnitude of a with grinding time is abundantly clear from the work of Fuerstenau8 on dry grinding. Fuerstenau shows very clearly in his Fig. 5 that at short retention times the parameter a is the same as that obtained by sizing over the complete size range. From this figure, it is obvious that sizing to only 400 mesh gave distribution curves similar to Mular's - that is, the slope apparently decreased systematically with increased grinding. As a consequence of the improper determination of a, the magnitude of ß given by Mular must be larger than the true value. In order to demonstrate this, the following Fig. 6 was taken from Mular's paper (his Fig. 1). Fuer-stenau's results show that we can approximate the correct value of K by drawing lines parallel to the short retention time curves through the 400-mesh

Jan 1, 1963

Discussion of the paper of DR. L. EDELEANU, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2313 to 2332. F. W. BUSHONG,* Pittsburgh, Pa.-This process of extraction is particularly advantageous in the case of Roumanian oil, on account of its high aromatic content. I have prepared a paper, which will appear probably next month in the Journal of Industrial and Engineering Chemistry, describing a series of two-degree fractions of oil from the Nowata field in Oklahoma. I have made extractions with liquid sulphur dioxide in accordance with Dr. Edeleanu's method, and found that the Oklahoma oils, for instance the kerosene fractions, are purified in this way, although the quantity taken out does not at all compare with that taken out of the Roumanian oil. I have made careful analyses of separate fractions, before and after extraction, and they show a very distinct fractional separation-. I like the distinction, brought out by Dr. Day in previous discussions, in regard to oils, rather than oil, and his beautiful illustration of fractionation. Just as fuller's earth, and other clays, will enable us to obtain lower-boiling fractional portions of the oils, and eventually retain a residuum which is hard to get rid of, or to remove, so there is an advantage to be gained by the use of a reagent which begins at the other end by taking out these last constituents first, namely, ozone. I have also analyzed the ozonides and they are derivatives of hydrocarbons very much poorer. in hydrogen than we have heretofore supposed. Similar results have been obtained with Roumanian, Russian, and Italian petroleums. Furthermore, I have prepared ozonides from a fraction of Oklahoma oils, both before and after ex-' traction with liquid sulphur dioxide, and found that the ozonide obtained from the extract is the same as that precipitated out of the original oils. In other words, the residual substance, which the fuller's earth retains, is the one first thrown down by the use of ozone, but it may also be extracted by liquid sulphur dioxide- and be thus separated in apparently unaltered condition. The analysis of this extract corresponds to the formula C15H20, which is surprising, since it is lower in hydrogen content than we have been in the habit of considering among the constituents of our oils. The extract was probably contaminated with other hydro-carbons, but I think it is unquestionable that we must look for hydro-carbons in petroleum which correspond to a formula at least -as low in hydrogen as C15H2o, and possibly even as low as C15H16.

Jan 4, 1915

By R. W. Heckel, H. P. Cheskis, A. Lawley, M. R. Pinnel

THERE are discrepancies reported in the literature regarding the micro and macro stress-strain behavior of metals and alloys. In particular, Young's modulus and micro yield measurements often show significant variations depending upon the techniques employed.'-" The purpose of this note is to correlate measurements made with four techniques and to indicate where some of these discrepancies might arise. Allied use of these techniques can provide a complete and consistent characterization of micro and macro stress-strain behavior (over the strain range of 10-9 to 10--2 in. in.-') from a minimum number of samples. Techniques. The techniques employed for measuring stress-strain behavior involved the use of a) linear differential transformers, b) SR-4 strain gages, c) longitudinal resonance waves, and d) X-ray diffraction. Specimen geometries and preparations are summarized in Table I for each technique. Differential Transformer and Strain Measurements. An Instron universal testing machine, modified with an alignment device, was used to apply the load via parallel-jaw grips. The signal from the load cell was applied to the Y scale of a Moseley X-Y recorder (sensitivity of 10 lb load per in. chart). The elongation was monitored simultaneously with strain gages mounted on three sides of the rectangular specimen, and with two linear variable differential transformers (LVDT) mounted at 90 deg to one another on faces that also contained the strain gages, Fig. 1. The signal from one of the LVDT's was applied to the X scale of the recorder (sensitivity 40 µ in. elongation per in. chart) in order to trace a continuous load-elonga-tion curve. Concurrently, the strain on the same face (i.e., the face monitored by the LVDT) was recorded by the corresponding strain gage. A stress-strain curve was plotted from the load cell-strain gage data and was compared to the stress-strain curve (converted from load-elongation) plotted from the continuous load cell-LVDT trace. Identical Table I. Description of Specimens Used in the Present Study Material Dimerisions Preparation Condition 99.99 pct A1 tensile 318 by 3/16 by 3 in. as cast ingot; cut annealed specimen on diamond wheel 2024 A1 tensile 318 by 3/20 by 31/2 in. vacuum hot annealed specimen pressed sheets; cut on diamond wheel 99.99 pct Al 3116 by 3/16 by 2 in. cut from tensile prestrained dynamic modulus specimen after 10"* in. specimen test per in. 2024 A1 dynamic 3/20 by 3/20 by 2 in. vacuum hot annealed modulus specimen pressed sheets; cut on diamond wheel 2024 A1 X-ray gage section 112 by vacuum hot annealed specimens 1/4by1/20in. pressed sheets; cut on diamond wheel

Jan 1, 1970

By Takao Kobayashi

Micro-crack formation zones developed near a crack tip in rocks and ceramics play a significant role in fracture behavior of these materials. In order to study micro- crack formation near a crack tip and its effects on crack behavior, a mica-epoxy composite material was developed. Multi-layer mica flakes were embedded in an epoxy matrix. Under high stress in the vicinity of a crack tip the mica delaminated, simulating the micro-cracking along grain boundaries or crystal planes in rocks and ceramics. A compact tension specimen was fabricated from mica-epoxy composite material. During the test the load and crack opening displacement were measured following the ASTM E561 (R-curve determination) procedure. Through the compliance calibration method the effective crack length and the KR were computed. The experiment clearly demonstrates the formation of micro-cracks and their effects on the overall behavior of the specimen. The paper discusses the significance of micro-crack formation on fracture toughness characterizations, and the advantages of the use of mica-epoxy composite for detailed studies of interaction between the micro-crack formation zone and the specimen geometry and size.

Jan 1, 1982

NEVADA SECTION J. W. HUTCHINSON, Chairman, FRANCIS CHURCH LINCOLN, Vice-Chairman, HENRY M. RIVES, Secretary-Treasurer, Reno, Nevada W. H. BLACKBURN, E. A. JULIAN, EMMET D. BOYLE, JOHN G. KIRCHEN, FREDERICK BRADSHAW, C. B. LAKENAN, TASKER L. ODDIE. The formation of the Nevada Section was originally suggested by Professor F. C. Lincoln, who had discussed the subject with Mr. William L. Saunders when the latter was President of the Institute. Professor Lincoln sought the assistance of the Nevada Mine Operators' Association, whose Executive Committee constituted itself a Committee on Organization, and authority for the establishment of a Nevada Section to include the entire State was secured from the Board of Directors of the Institute. The formal installation took place at 10 A.M. on May 18, Mr. William L. Saunders officiating. The Honorable Emmet D.. Boyle, Governor of Nevada (and a member of the Nevada Section), made the address of welcome. On the afternoon of the same day, a technical session was held, at which the following papers were presented: History and Development of the Cyanide Process Charles Butters Virginia City Whitman Symmes Ore Deposition at Steamboat Springs Prof. J. C. Jones

Jan 7, 1916

By G. K. N. S. Subasinghe

An attempt has been made to explain the behavior of a pinched sluice in terms of the established theories of fluid mechanics and mineral processing. A method has been developed to calculate the underflow discharge by assuming a logarithmic velocity distribution and free gravity fall through the discharge slot. The concentration profile of solids over the depth of flow has been shown to comply with Bagnold's theory of dispersive shear, rather than turbulent sediment transfer. Even although the results can be explained qualitatively by the Bagnold theory, their complete quantitative analysis will not be possible until more work is done. Consequently, an empirical equation has been developed to predict underflow pulp densities. It has been shown that the process of the segregation of the heavier mineral beneath the lighter can be described by a first order law. From the results obtained, a computer model of the pinched sluice has been developed. This predicts the underflow grade, pulp density and flow rate in terms of the feed and operating conditions. The model can also be used to determine the effect of a change in operating conditions, and for the optimization of rougher, cleaner, and scavenger circuits.

Jan 1, 1984

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By J. H. Keeler

The tensile characteristics of Zr-Fe binary alloys containing up to 5 atomic pet Fe are reported for the temperature range —195o to 500°C. A linear relation between stress at constant strain and volume fraction ZrFe2 was found. The coincidence of data from unalloyed zirconium with zero volume fraction ZrFe2 indicated little or no solid solution in IL-zirconium, in agreement with Hayes, Roberson, and O'Brien.' The absolute increase in strength due to particle strengthening, although decreasing with increasing temperature, was a greater percentage at high temperature. ZIRCONIUM is of interest for use in nuclear reactors because of its low neutron absorption, good corrosion resistance, and high melting temperature. The alloying of zirconium with iron has been considered as a means of increasing the mechanical strength of zirconium without seriously increasing the neutron absorption " over that of unalloyed zirconium. The Zr-Fe system has a eutectic at 934°C and 23.7 atomic pet Fe and a eutectoid at 800°C and 4.0 atomic pet Fe. The zirconium-rich end of this system determined by Hayes, Roberson, and O'Brien' is shown in Fig. 1. The intermetallic phase coexisting with a and ß-zirconium has been reported as Zr2Fe3,1 with a,, - 7.04A, and as ZrFe2,2 face-centered-cubic, the phase being of the MgCu, type (C-15). It was more recently agreed to be ZrFe33 and face-centered-cubic. This intermetallic phase is essentially insoluble in a-zirconium, the hexagonal-close-packed modification; and the lack of solubility makes the system particularly interesting metallurgically. The system is strengthened almost exclusively by particles of in-termetallic phase, and there is very little solid solution strengthening to complicate the analysis. The Bureau of Mines, in its survey of zirconium-base alloys,' reported the tensile properties of Zr-Fe alloys made from chloride process zirconium, induction melted in graphite crucibles, and swaged at 850°C in iron sheaths. Additional data on these ZrFe alloys were given by Hayes, Roberson, and O'Brien.' Chubb and Muehlenkamp% have recently reported the strength of Zr-Fe alloys containing up to about 1.25 atomic pet Fe. These alloys were made from crystal bar zirconium, hot worked at 820°C, annealed at 700°C, and tested both at room temperature and at 316°C. Experimental Procedure The materials used in this investigation were high purity zirconium made by the iodide process and electrolytic iron. The composition of the zirconium as obtained by spectrographic analysis and the nominal composition of the iron are given in Table I. Alloy ingots weighing 100 g were made by are-melting under argon in water-cooled copper crucibles in a multihearth furnace."

Jan 1, 1957

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young's modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie's3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

EUGENE MCAULIFFE, St. Louis, Mo. (written discussion*).-When we undertook the development of the Kathleen mine, near DuQuoin, certain features greatly influenced the construction and underground development. The country is very flat, so that the usual gravity yard movement of empty and loaded coal cars would entail a very heavy fill at the empty-car end of the tracks, with some form of car-pulling arrange-ment to move the loads where it was practically impossible to provide. a gravity movement. So the yard was made level, except for 1000 ft. (304 m.) under the two tipples, where the cars are moved by gravity and controlled under the main-shaft tipple by four Fairmont car retarders. Both tipples are spread sufficiently to admit of introducing a narrow-gage track and locomotive. One 18-ton locomotive is at present employed in moving empties clown to a point above the main-shaft tipple and the loads off the track scales clown into the storage yard; ultimately a 25-ton loco-motive will be employed on the loaded side of the tipple. This form of car movement and control will admit of handling empty and loaded cars

Jan 11, 1919