Search Documents

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By Eugene McAuliffe

HAVING reached the status of an octogenarian plus, I suddenly decided to take a trip to Great Britain by airplane, before the possibility of hardening of the arteries made such a program too precarious. Of thirty June and July days spent in the islands, five were spent in the south of Ireland, or Eire as the politicians like to call their country. On June 15 I arrived in Glasgow where a day was spent with old friends before moving on to Edinburgh, where the Institution of Mining Engineers was billed to hold its summer session. I had received a cablegram before leaving New York inviting me to attend the sessions which I accepted with avidity, spending three most enjoyable and informative days with old friends and the officers of the Institution, Douglas Hay, president; Ian McDermid, secretary; and members of the council.

Jan 1, 1947

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors' notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By Paul Weir

PRODUCTION METHODS in the bituminous coal mines in the United States are undergoing many changes. Although the primary object of these changes is the production of a better product at a cheaper cost there are other considerations such as the improvement of conditions under which miners live and work. The almost complete unionization of the manual workers in the industry during the past four years has 'brought with it a stabilization of wages on a relatively high basis and of hours of work per day and per week on a relatively low basis. With differentials in wages between producing districts firmly established, and with a nation- wide and uniform application of in-

Jan 1, 1937

By D. W. Reed, R. L. Reed, Tracht

Laboratory experiments on the reverse combustion of tar sands in a linear adiabatic system have shown that a highly upgraded oil can be produced from an exceedingly viscous, immobile oil. The dependence on the air-injection rate of peak temperature, combustion-zone velocity, oil recovery, air-oil ratio, residual coke and oil, fuel burned and distribution of product gases is shown graphically. Eflects of initial temperature, oxygen concentration, oil saturation and heat loss are discussed. Experiments bearing on the coking properties of heavy oils are mentioned and some results exhibited. Field application of the process hinges on the existence of adequate air permeability and the rate of reaction under reservoir conditions. INTRODUCTION It has been established that oil can be recovered from underground reservoirs by means of at least two fundamentally distinct methods involving in situ combustion of a certain fraction of the oil. Characteristic of both of these known methods is the production of oil from one or more wells by means of hot gases formed when a high-temperature reaction zone is advanced through the reservoir. In both cases, the reaction zone is created by heating certain of the wells to a sufficiently high temperature prior to the introduction of air, and the zone is maintained and advanced through the reservoir by appropriate control of the air-injection rate. In the first of these methods, which is called "forward combustion",' the combustion zone advances in a direction which is generally the same as that of the air flow; whereas in the second method, "reverse combustion",' the combustion zone moves in a direction generally opposite to that of the air flow. Forward combustion, on the one hand, is an ideal combustion process in the sense that a minimum of the most undesirable fraction of the oil is consumed as fuel in the form of coke, a clean sand is left behind and generated heat is used as efficiently as possible. However, the applicability of forward combustion is limited. Since the products of combustion, vaporized oil and connate water must flow into relatively cold regions of the reservoir, there is an upper limit on the viscosity of oil which can be moved by this process in a practical and economical fashion.' On the other hand, it is characteristic of reverse combustion that the vaporized oil and water together with the products of combustion are produced through sand which is already hot and has had its mobile liquid content eliminated. This means there is no upper limit on oil viscosity; indeed, the oil may be an entirely immobile semi-solid. However, fuel for the process is an intermediate fraction of the original oil, and the most undesirable fraction remains on the sand surface as a substantial deposit of coke. Since this coked material is not burned during reverse combustion, it represents energy which is available for the production of oil but is not used for this purpose. It follows that one can expect economics to be somewhat less attractive with reverse combustion than with forward combustion. Nevertheless, it is a process which is designed for reservoirs where forward combustion is impossible and, as such, has become a subject of experimental and theoretical investigation. In this paper, only experiments made with tar sands are discussed. DESCRIPTION OF THE PROCESS We proceed, then, to consider the process of reverse combustion in greater detail. Fig. 1 illustrates a temperature profile defining a combustion zone which moves from right to left when air flows from left to right. In Zone 1, the temperature is the initial reservoir temperature, and the tar sand is as yet unaltered. This statement must be modified to the extent that physical properties of the oil may be changed by low-temperature oxidation at reservoir temperature. As air passes into Zone 2, which has been warmed by conduction, it assists in vaporization of the very light ends (if there are any), and oxidation occurs at a significant rate. In this region, there is almost no production of carbon monoxide or carbon dioxide because predominantly addition-type reactions take place with the formation of oxygenated compounds such as aldehydes and acids together with water. The hydrocarbon-enriched and slightly oxygen-depleted gas stream enters Zone 3 where

By William Kent

In a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on " Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron procluced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the " furnace hook," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable callses which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wetor dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1879

By William C. Harrigan, William D. Nix

Dynamic measurements of Young's modulus have been made for poly crystalline Ni-W alloys from room temperature to 800°C. The alloys studied range in composition from pure nickel to Ni-10 at. pct W. The results indicate that Young's modulus decreases linearly with temperature above the Curie temperature. The rate of change of Young's Modulus with temperature mas found to range from 104 psi per "C for pure nickel to 0.82 x 104 psi per °C for Mi-10 pct W. At all temperatures the elastic modulus decreases with increcrsing tungsten content up to 1 at. pct W, and increases as the tungsten content is increased above that level. Young's modulus decreases slightly as the carbon content is increased from 0.002 to 0.09 wt pct C THE knowledge of the elastic modulus of metals and alloys is important for a number of reasons. The first and most obvious reason comes from the need to predict elastic deflections under given loading conditions. A second and somewhat more subtle reason comes from the fact that the elastic properties of an alloy must be known before a proper account of the mechanisms of plastic deformation can be made. This is especially true for high-temperature creep of crystalline solids. Sherby and his coworkers have shown that the high-temperature steady-state creep rates of crystalline solids are inversely related to the elastic modulus1,2 and that the temperature dependence of the elastic modulus must be taken into account if reliable determinations of the activation energy for creep are to be made. In addition, measurements of the elastic constants of solid solutions are needed to allow one to assess the modulus interaction contribution to solid-solution Strengthening.3-5 Pelloux and Grant6 have demonstrated that substantial solid-solution strengthening at room temperature and elevated temperatures occurs when refractory metal solute atoms are added to nickel. While the high-temperature elastic properties of pure nickel have been measured by a number of authors,7-10 the elastic properties of nickel-based refractory metal alloys have not been determined. The purpose of this paper is to report on measurements of Young's modulus of polycrystalline Ni-W alloys at elevated temperatures. It is expected that these measurements will be valuable to studies of the mechanical properties of nickel-based refractory metal solid solutions. I) EXPERIMENTAL Young's moduli of polycrystalline samples were determined by a dynamic method in order to reduce high- temperature anelastic and plastic relaxations. The samples were forced in transverse free-free vibration; that is, both ends of the sample were unrestrained and the vibration was transverse to the long axis. The fundamental resonant frequency was determined by the Forster method.11 The analysis of this type of vibration which was formulated by Rayleigh,12 Timo-chenko,13 and pickett,14 and reviewed by Fine," leads where fn is the resonant frequency of the nth mode, r is the radius of the circular cross section. L is the specimen length, ßn is 1.5056 for free-free vibration in the fundamental mode of vibration, 6 is the mass density, and E is Young's modulus in the axial direction. This equation can be transformed into: E = 9.17605 x 10-6(L/D)E/Lf2 [2] where E is Young's modulus in psi, L is the length in inches, d is the diameter in inches, W is the weight in grams, and f is the resonance frequency in cps. Eq. [2] was further modified in order to take account of the thermal expansion of the samples. The resulting correct term is: where the thermal expansion coefficients for nickel and tungsten, respectively. Xw is the atom fraction of tungsten in the sample and T is the temperature in "C. The treatment of the thermal expansion coefficient as a linear function of composition seems sufficiently accurate since an error of 25 pct in the expansion coefficient will result in only a 0.3 pct error in the modulus at 1000°C. A) Apparatus. The equipment for this investigation has been described by Lytton et al.16 Several modifications of the equipment have been made. The most significant change involved replacing the detector crystal transducer with a magnetic transducer. A phonographic magnetic transducer was employed as a sensing device since the contact pressure necessary to produce a stable signal is much less than that for a crystal transducer. This magnetic transducer is also not affected by conditions of high temperature and vacuum which are present in these experiments. The vacuum was 10-5 torr at room temperature and about 5 x 10-4 torr at 900°C. This was sufficient to prevent surface contamination of the samples during the tests. The samples were heated in an elliptical furnace with a quartz lamp at one focal line and the sample at the other, as described by Lytton et a1.16 The temperature of the sample was measured by monitoring the

Jan 1, 1969

Arthur Yates, lecturer in the mining department of the Royal School of Mines, London, died at Blackpool, on Feb. 14, 1923, at the age of 47 years. My first acquaintance with him was made in 1902, when taking over the management of the Redjang Lebong gold mines in Sumatra, of which he was the responsible metallurgical officer. For that position he was well qualified by reason of his previous experience with the Rand Central Ore Reduction Co., in South Africa, and particularly by his early training with the Cassel Gold Extracting Co., owners of the MacArthur-Forrest patents, and the first commercial company formed to work the then recently discovered cyanide process; in this connection, Mr. Yates had the advantage of working under J. S. MacArthur himself. Our association in Sumatra was maintained for six years, when I left. Mr. Yates remained and was eventually promoted to the management of the neighboring Soelit mine. During those six years and in the close association inseparable from life in an isolated mining camp, the sterling qualities which made him so good a man were unmistakable: industry and interest in his work, patience with everybody, a quiet and unassuming demeanor. On the exhaustion of the mine to which he had been promoted, he returned to England in 1913. In 1914, the Mining Department of the Imperial College was fortunate in securing his services. Hardly, however, had he settled down when the war broke out and he spent some years in the Cleveland District promoting the efforts of the Government toward greater output. Returning to college in 1919, Mr. Yates met the full flood of Service students. The qualities which made him a man amongst men in the world made him a man among students in the college; a senior student if you like. But, unsuspected, a dread disease had fastened itself upon him, making itself felt for the first time during the summer course he was conducting in the South Wales coal field, in 1922. Against its relentless onset he opposed the bravest optimism, and when at last he realized that he was going under, and was in fact dying, his pronounced regret was that he was leaving the boys. In his death, at the age of forty-seven, staff and students in the Mining Department have experienced a great loss, that of a reliable friend, and their deepest sympathy goes out to the young widow and son in their irreparable loss. S. J. TRuBcott.

Jan 1, 1923

Arthur Yates, lecturer in the mining department of the Royal School of Mines, London, died at Blackpool, on Feb. 14, 1923, at the age of 47 years. My first acquaintance with him was made in 1902, when taking over the management of the Redjang Lebong gold mines in Sumatra, of which he was the responsible metallurgical officer. For that position he was well qualified by reason of his previous experience with the Rand Central Ore Reduction Co., in South Africa, and particularly by his early training with the Cassel Gold Extracting Co., owners of the MacArthur-Forrest patents, and the first commercial company formed to work the then recently discovered cyanide process; in this connection, Mr. Yates had the advantage of working under J. S. MacArthur himself. Our association in Sumatra was maintained for six years, when I left. Mr. Yates remained and was eventually promoted to the management of the neighboring Soelit mine. During those six years and in the close association inseparable from life in an isolated mining camp, the sterling qualities which made him so good a man were unmistakable: industry and interest in his work, patience with everybody, a quiet and unassuming demeanor. On the exhaustion of the mine to which he had been promoted, he returned to England in 1913. In 1914, the Mining Department of the Imperial College was fortunate in securing his services. Hardly, however, had he settled down when the war broke out and he spent some years in the Cleveland District promoting the efforts of the Government toward greater output. Returning to college in 1919, Mr. Yates met the full flood of Service students. The qualities which made him a man amongst men in the world made him a man among students in the college; a senior student if you like. But, unsuspected, a dread disease had fastened itself upon him, making itself felt for the first time during the summer course he was conducting in the South Wales coal field, in 1922. Against its relentless onset he opposed the bravest optimism, and when at last he realized that he was going under, and was in fact dying, his pronounced regret was that he was leaving the boys. In his death, at the age of forty-seven, staff and students in the Mining Department have experienced a great loss, that of a reliable friend, and their deepest sympathy goes out to the young widow and son in their irreparable loss. S. J. TRuBcott.

Jan 1, 1923

By Paul H. Hunt

MANY MISUNDERSTANDINGS have arisen regarding -Al the purchase by the Government of 24,000,000 oz. of domestically produced silver annually for the next four years at a price of 64 1/2c. to the producer. Some editorials have an¬nounced rather sarcastically that be¬cause of the strong western silver bloc in Congress, the Administration is paying a bonus of approximately $22,000,000 to a few large silver produc¬ers of the West, the amount being figured on the total purchase of about 100,000,000 oz. and the difference between the Government price and the world price for silver. Actually the Government will make a profit on this purchase, due to seigniorage, of something over $60,000,000. The 96,000,000 oz. of silver, for which the producers will receive approximately $62,000,000, will be produced in association with at least $100,000,000 worth of lead, zinc, copper and gold; the greater part of this $162,000,000 worth of metal will be produced at little profit to the mining companies, as will be shown later, because of the low prices for lead, copper and zinc. This amount of money will be spent largely for labor and supplies, thus greatly relieving the national burden of unemployment. Certainly, western mining, in the purchase of this silver, is not victimizing the Federal Government.

Jan 1, 1934

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

By A. A. Beard

ABOUT three years ago, I. L. Dunn, of Marietta, Ohio, found that wells could be cleaned by blowing with compressed air; this method has been used with great success on many wells in the Marietta, Ohio, district, where compressed air is being used to increase production, by forcing oil through the depleted sands. About a year ago, the process was successfully used to clean out wells in the Lenapah pool in Oklahoma, where an air plant had been installed, under the supervision of I. L. Dunn. Wells from 900 to 1000 ft. deep, with 40 ft. of sand and cavings in them, were cleaned out in from two to three days. The use of this process had, so far, been limited to properties using the Smith-Dunn process, where compressed air, under suitable pressure and volume, was available. For other properties, a portable compressor seemed essential; this was built and successfully demonstrated by Mr. Dunn, for the Tidal Oil Co. in September, 1924. The process of cleaning out with air has been described.1 It consists of lowering the tubing into the well, with a shoe or nipple of heavy pipe substituted for the perforated anchor on the bottom. Into the tubing, compressed air is introduced through a rotary swivel hose at the top, or by means of swing connections. The tubing is lowered to the top of the cave to be cleaned out, several barrels of water are put into the hole, and the compressed air is turned on. This blows out the material between the casing and the tubing, the tubing being lowered as the material is removed.

Jan 9, 1925

By Edwin Ludlow

EDWIN LUDLOW, president of the American Institute of Mining and Metallurgical Engineers for the year beginning Feb. 15, 1921, is a well-known figure in the state that was the birthplace of the Institute-Pennsylvania-although he was born and educated in New York and is again one of its residents, after years of active work in the field. Mr. Ludlow was born at Oakdale, Long Island, and was graduated from the School of Mines at Columbia University with the class of 1879. After graduation, he became a civilian worker with the U. S. Engineer Corps under General William Ludlow, his brother, and for two years did river and harbor surveying along the New Jersey coast.

Jan 1, 1921

By W. L. Saunders

THE world's greatest producing area is, geographically, in the midland region of North America about the Great Lakes. This area, with but one- third of the nation's population, produces, with the exception of tobacco and cotton, three-quarters of the principal staples. It provides the surplus or export grain, meats, dairy products, steel and leading minerals. The social and political condition of a nation is determined by its industrial efficiency, and the share of the commerce of the world obtained by a nation is fixed more by the economy of its transportation than by any other factor. It is an economic maxim that: The total cost is the cost of production plus transportation cost. The cost of carrying 1000 tons by water or 100 tons by rail is equal, over the same distance

Jan 1, 1921

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By F. W. Davis

SOME idea may be gained of the tremendous consumption of refractories by the open-hearth steel manufacturers from a statement made by A. T. Green at a meeting reported by T11.e Industrial Chemist of London, as follows: "At a very progressive steel plant in the Midlands, with a battery of five open-hearth furnaces working. twelve months and making 3000 tons of steel per week, the cost of refractories per ton of steel produced averages about $0.50 for the actual open- hearth casting and $0.12 for those operations incidental to the rolling of the metal." .These figures, when translated into the annual tonnage of steel, represent a very considerable expenditure.

Jan 1, 1930